SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A measurement circuit to obtain buffet data from wind tunnel models wherein a signal proportional to the average RMS value of buffet data is produced for subsequent recording. Feedback means are employed to suppress the D.C. portion of signals developed by the strain gages during dynamic testing. Automatic recording of gain settings of amplifiers employed in the circuit is also provided.
Data on atmospheric pressure, density, temperature and winds between 50 and 200 km were collected from sources including Meteorological Rocket Network data, ROBIN falling sphere data, grenade release and pitot tube data, meteor winds, chemical release winds, satellite data, and others. These data were analyzed by a daily difference method and results on the distribution statistics, magnitude, and spatial structure of the irregular atmospheric variations are presented. Time structures of the irregular variations were determined by the analysis of residuals from harmonic analysis of time series data. The observed height variations of irregular winds and densities are found to be in accord with a theoretical relation between these two quantities. The latitude variations (at 50 - 60 km height) show an increasing trend with latitude. A possible explanation of the unusually large irregular wind magnitudes of the White Sands MRN data is given in terms of mountain wave generation by the Sierra Nevada range about 1000 km west of White Sands. An analytical method is developed which, based on an analogy of the irregular motion field with axisymmetric turbulence, allows measured or model correlation or structure functions to be used to evaluate the effective frequency spectra of scalar and vector quantities of a spacecraft moving at any speed and at any trajectory elevation angle.
The accumulation of the large deposits of volatile and nonvolatile sediments at both Martian poles has occurred through periods of likely climate change. Most data on wind directions near the Martian poles and seasonal activity relate to a very short period of time, at one point in climate cycles. It is still uncertain what the net budgets to the poles are and how this budget (if known) would fit into longer climate/sediment cycles. Pending further data we examined the full suite of Viking high-resolution, high-latitude images for wind markers of all sizes and types. These probably represent timescales of formation from days to several tens of thousands of years. The goal is to estimate the effectiveness, and possible drivers, of wind systems that bring materials near the surface to the regions of polar sediments and that also remove materials from the polar areas.
The general objective of this effort is to increase understanding of how frontal scale contraction processes may create and sustain intense mesoscale precipitation along intensifying cold fronts. The five-part project (an expansion of the originally proposed two-part project) employed conventional meteorological data, special mesoscale data, remote sensing measurements, and various numerical models. First an idealized hydrostatic modeling study of the scale contraction effects of differential cloud cover on low-level frontal structure and dynamics was completed and published in a peer-reviewed journal. The second objective was to complete and publish the results from a three dimensional numerical model simulation of a cold front in which differential sensible heating related to cloud coverage patterns was apparently crucial in the formation of a severe frontal squall line. The third objective was to use a nonhydrostatic model to examine the nonlinear interactions between the transverse circulation arising from inhomogeneous cloud cover, the adiabatic frontal circulation related to semi-geostrophic forcing, and diabatic effects related to precipitation processes, in the development of a density current-like microstructure at the leading edge of cold fronts. Although the development of a frontal model that could be used to initialize such a primitive equation model was begun, we decided to focus our efforts instead on a project that could be successfully completed in this short time, due to the lack of prospects for continued NASA funding beyond this first year (our proposal was not accepted for future funding). Thus, a fourth task was added, which was to use the nonhydrostatic model to test tentative hypotheses developed from the most detailed observations ever obtained on a density current (primarily sodar and wind profiler data). These simulations were successfully completed, the findings were reported at a scientific conference, and the results have recently been submitted to a peer-reviewed journal. The fifth objective was to complete the analysis of data collected during the Cooperative Oklahoma Profiler Studies (COPS-91) field project, which was supported by NASA. The analysis of the mesoscale surface and sounding data, Doppler radar imagery, and other remote sensing data from multi frequency wind profiler, microwave radiometer, and the Radio Acoustic Sounding System has been completed. This study is a unique investigation of processes that caused the contraction of a cold front to a microscale zone exhibiting an undular bore-like structure. Results were reported at a scientific conference and are being prepared for publication. In summary, considerable progress has been achieved under NASA funding in furthering our understanding of frontal scale contraction and density current - gravity wave interaction processes, and in utilizing models and remotely sensed data in such studies.
The high-resolution wind profile of the Automated Meteorological Profiling System (HRAMPS) is the proposed replacement for the Jimsphere measurement system used to support NASA Shuttle launches from the Eastern Test Range (ETR). Samples of twenty-six ETR near simultaneous Jimsphere and HRAMPS wind profiles were obtained for Shuttle program HRAMPS certification studies. Shuttle systems engineering certification is to ensure that spacecraft and launch vehicle systems performance and safety evaluations for each launch (derived from flight simulations with Jimsphere wind profile data bases) retain their validity when HRAMPS profiles are used on day-of-launch (DOL) in trajectory and loads simulations to support the commit-to-launch decision. This paper describes a statistical analysis of the near simultaneous profiles. In principle the differences between a Jimsphere profile and an HRAMPS profile should be attributed to tracking technology (radar versus GPS tracking of a Jimsphere flight element) and the method for derivation of wind vectors from the raw tracking data. In reality, it is not technically feasible to track the same Jimsphere balloon with the two systems. The aluminized Mylar surface of the standard Jimsphere flight element facilitates radar tracking, but it interferes with HRAMPS during simultaneous tracking. Suspending a radar reflector from an HRAMPS flight element (Jimsphere without aluminized coating) does not produce satisfactory Jimsphere profiles because of intermittent radar returns. Thus, differences between the Jimsphere and HRAMPS profiles are also attributed to differences in the trajectories of separate flight elements. Because of small sample size and a test period limited to one winter season, test measurements during extreme high winds aloft could not have been expected and did not occur. It is during the highest winds that the largest differences between Jimsphere and HRAMPS would occur because the distance between flight elements would be larger. Jimsphere radar tracking noise increases as a function of balloon displacement downrange. The Jimsphere data processing compensates for tracking signal/noise degradation by increasing the smoothing interval. The Jimsphere wind profile effective resolution is a function of downrange distance and altitude, whereas the effective resolution of the HRAMPS should be independent of those variables. The procedure used for editing Jimsphere spikes in Shuttle DOL profiles was not implemented for the Jimsphere profile measurements during the AMPS field tests. For this analysis a code was developed that essentially mimics DOL Jimsphere spike editing. Jimsphere profiles have somewhat more noise in the wavelength range less than 200m defined as the noise floor. No differences between Jimsphere and HRAMPS wind profile pairs have been found that would support denial of HRAMPS certification for application in Shuttle DOL applications. The reliability of the HRAMPS system, which is an important certification issue, is not addressed in this study.
A 10 m height wind vector data set, named CMODFD, from ERS-1 Active Microwave Instrument (AMI) measurements, was compared with moored buoy wind observations. The CMODFD wind vectors compared favorably with moored buoy wind observations at about 60 sites. Satisfactory results were obtained from intercomparisons between CMODFD and moored buoy estimates of horizontal wind divergence and wind stress curl. The CMODFD positions of the Intertropical Convergence Zone (ITCZ) at 28 deg west were nearly equal to those determined from satellite images of clouds. The CMODFD data were employed to compute the Ekman vertical velocity in the region of the Pacific North Equatorial Countercurrent (NECC), and a correlative relation was found between the annual cycles and longitudinal variations of the NECC and Ekman vertical motion.
It has long been recognized that frequency and phasing of structural modes in the presence of airflow play a fundamental role in the occurrence of flutter. Animation of simulation results for the long, slender Semi-Span Super-Sonic Transport (S4T) wind-tunnel model demonstrates that, for the case of mass-ballasted nacelles, the flutter mode can be described as a traveling wave propagating downstream. Such a characterization provides certain insights, such as (1) describing the means by which energy is transferred from the airflow to the structure, (2) identifying airspeed as an upper limit for speed of wave propagation, (3) providing an interpretation for a companion mode that coalesces in frequency with the flutter mode but becomes very well damped, (4) providing an explanation for bursts of response to uniform turbulence, and (5) providing an explanation for loss of low frequency (lead) phase margin with increases in dynamic pressure (at constant Mach number) for feedback systems that use sensors located upstream from active control surfaces. Results from simulation animation, simplified modeling, and wind-tunnel testing are presented for comparison. The simulation animation was generated using double time-integration in Simulink of vertical accelerometer signals distributed over wing and fuselage, along with time histories for actuated control surfaces. Crossing points for a zero-elevation reference plane were tracked along a network of lines connecting the accelerometer locations. Accelerometer signals were used in preference to modal displacement state variables in anticipation that the technique could be used to animate motion of the actual wind-tunnel model using data acquired during testing. Double integration of wind-tunnel accelerometer signals introduced severe drift even with removal of both position and rate biases such that the technique does not currently work. Using wind-tunnel data to drive a Kalman filter based upon fitting coefficients to analytical mode shapes might provide a better means to animate the wind tunnel data.
The implementation of available wind shear data into general aviation flight training simulators is discussed. Currently, there are 11 simulators with wind shear models installed involving some 9 different aircraft models. Retrofits to other systems that were put out earlier are currently underway, and all the new simulators will have wind shear available for the instructors to use for demonstrations and training. There are three types of computer systems involved, and two different types of instructor stations. Most of the systems with wind shear are the CRT-type displays. The integration of wind shear models in flight simulators is discussed in detail.
The Goddard Lidar Observatory for Winds (GLOW) is a mobile direct detection Doppler lidar system designed to measure wind profiles from the surface into the lower stratosphere. Recently, the GLOW lidar has participated in several field deployments measuring tropospheric winds in a variety of conditions including both daytime and night operation. More than 50 hours of line-of-sight wind profit data were obtained in September, 2000 during a three week intercomparison experiment at the Ground Winds facility in North Glen, NH. Typical clear air lidar wind profiles extended to altitudes of 20 km with a 1 km vertical resolution and 1 minute averaging. An additional 40 hours of lidar profiles of wind speed and direction were obtained during HARGLO-2, an intercomparison experiment held at Wallops Flight Facility, VA in November, 2001. A description of the mobile system is presented along with the examples of validated lidar wind profiles obtained during these experiments.
A collection of computational fluid dynamics tools and techniques are being developed and tested for application to stage separation and abort simulation for next-generation launch vehicles. In this work, an overset grid Navier-Stokes flow solver has been enhanced and demonstrated on a matrix of proximity cases and on a dynamic separation simulation of a belly-to-belly wing-body configuration. Steady cases show excellent agreement between Navier-Stokes results, Cartesian grid Euler solutions, and wind tunnel data at Mach 3. Good agreement has been obtained between Navier-Stokes, Euler, and wind tunnel results at Mach 6. An analysis of a dynamic separation at Mach 3 demonstrates that unsteady aerodynamic effects are not important for this scenario. Results provide an illustration of the relative applicability of Euler and Navier-Stokes methods to these types of problems.
This paper describes the techniques involved in determining the aerodynamic stability derivatives for the frequency domain analysis of the Space Launch System (SLS) vehicle. Generally for launch vehicles, determination of the derivatives is fairly straightforward since the aerodynamic data is usually linear through a moderate range of angle of attack. However, if the wind tunnel data lacks proper corrections then nonlinearities and asymmetric behavior may appear in the aerodynamic database coefficients. In this case, computing the derivatives becomes a non-trivial task. Errors in computing the nominal derivatives could lead to improper interpretation regarding the natural stability of the system and tuning of the controller parameters, which would impact both stability and performance. The aerodynamic derivatives are also provided at off nominal operating conditions used for dispersed frequency domain Monte Carlo analysis. Finally, results are shown to illustrate that the effects of aerodynamic cross axis coupling can be neglected for the SLS configuration studied
An unsteady Reynolds averaged Navier-Stokes analysis loosely coupled with a comprehensive rotorcraft code is presented for a second-generation active-twist rotor. High fidelity Navier-Stokes results for three configurations: an isolated rotor, a rotor with fuselage, and a rotor with fuselage mounted in a wind tunnel, are compared to lifting-line theory based comprehensive rotorcraft code calculations and wind tunnel data. Results indicate that CFD/CSD predictions of flapwise bending moments are in good agreement with wind tunnel measurements for configurations with a fuselage, and that modeling the wind tunnel environment does not significantly enhance computed results. Actuated rotor results for the rotor with fuselage configuration are also validated for predictions of vibratory blade loads and fixed-system vibratory loads. Varying levels of agreement with wind tunnel measurements are observed for blade vibratory loads, depending on the load component (flap, lag, or torsion) and the harmonic being examined. Predicted trends in fixed-system vibratory loads are in good agreement with wind tunnel measurements.
The Single Field of View (SFOV) Sounder Atmospheric Products (SiFSAP) derived from Cross-track Infrared Sounder (CrIS) on SNPP and JPSS have a spatial resolution ( ~14.5 km) better than most global weather and climate models. Most recent significant improvement in the quality of these products enables us to use these high-resolution observation-based sounding data for weather studies and model evaluation. The aim of this study is to explore the value to use these SFOV products for studying the dynamic transport associated with polar vortex outbreak. In a few cases studies, we used SiFSAP products, especially ozone, as well as the data of wind, geopotential height (GPH) and potential velocity (PV) from the fifth-generation ECMWF reanalysis (ERA5) data, to analyze the variation of total ozone, relative humidity and ozone in different layers, as well as their correlation with GPH and PV. Some comparison of the retrieved temperature and water vapor with ERA5 data, and ozone with the Ozone Mapping and Profiler Suite (OMPS) measurements have also been made. It is found (1) the transport of O3-riched polar air accompanying the polar vortex breakup to lower latitude and lower atmosphere, and (2) the transport path of O3 agreeing well with the path of polar cold air (illustrated using the retrieved RH, wind fields and GPH). These results demonstrate the 3-D structure of O3 distribution as derived from CrIS measurements provides some insights of the cold air transport, and can be used to track the dynamic transport of polar cold air following the outbreak of polar vortex. The observed enhancement of O3 following the polar vortex outbreak also suggests some possible linkage between the tropospheric cold air advected with stratospheric air source.
The purpose of this paper is to report a new data-driven analysis methodology for identifying nonlinear modal interactions and its application to aeroelastic wind-tunnel data from a generic fighter configuration, which reveals global modal interactions in this system caused by multiple resonance capture events initiated by local nonlinearities. It is shown that during supersonic testing at the Transonic Dynamics Tunnel, vibro-impacts at the embedded external fuel tank shakers on the inboard underwing stations of the generic fighter introduce strong nonlinearity that gives rise to nonlinear modal interactions. Specifically, time–frequency analysis of the acceleration data demonstrates that 6∶5 and 7∶6 transient resonance captures occur across the aircraft exclusively during this vibro-impact forcing window. Further analysis suggests that these resonance captures are dependent on Mach number. These results show experimentally that local vibro-impacts can cause global nonlinear effects in an aeroelastic system and that these effects can be identified using the new methodology herein. The data-driven analysis scheme employed shows applicability to full-aircraft flight test data for identifying nonlinear modal interactions without knowledge of the precise nonlinear contributors.
We describe the results of a statistical survey of Wind-Waves data motivated by the recent STEREO/Waves discovery of large-amplitude whistlers in the inner magnetosphere. Although Wind was primarily intended to monitor the solar wind, the spacecraft spent 47 h inside 5 R(sub E) and 431 h inside 10 R(sub E) during the 8 years (1994-2002) that it orbited the Earth. Five episodes were found when whistlers had amplitudes comparable to those of Cattell et al. (2008), i.e., electric fields of 100 m V/m or greater. The whistlers usually occurred near the plasmapause. The observations are generally consistent with the whistlers observed by STEREO. In contrast with STEREO, Wind-Waves had a search coil, so magnetic measurements are available, enabling determination of the wave vector without a model. Eleven whistler events with useable magnetic measurements were found. The wave vectors of these are distributed around the magnetic field direction with angles from 4 to 48deg. Approximations to observed electron distribution functions show a Kennel-Petschek instability which, however, does not seem to produce the observed whistlers. One Wind episode was sampled at 120,000 samples/s, and these events showed a signature that is interpreted as trapping of electrons in the electrostatic potential of an oblique whistler. Similar waveforms are found in the STEREO data. In addition to the whistler waves, large amplitude, short duration solitary waves (up to 100 mV/m), presumed to be electron holes, occur in these passes, primarily on plasma sheet field lines mapping to the auroral zone.
The Marshall Space Flight Center (MSFC) is charged with the responsibility to enhance aviation safety through improving understanding of various atmospheric phenomena. A brief discussion is presented concerning the tasks and work being accomplished by MSFC. The tasks are defined as follows: (1) to determine and define the turbulence and steady wind environments induced by buildings, towers, hills, trees, etc., (2) to identify, develop, and apply natural environment technology for the reconstruction and/or simulation of the natural environment for aircraft accident investigation and hazard identification, (3) to develop basic information about free atmosphere perturbations, (4) to develop and apply fog modification mathematical models to assess candidate fog modification schemes and to develop appropriate instrumentation to aquire basic data about fog. To accomplish these tasks MSFC has developed a program involving field data acquisition, wind tunnel studies, theoretical studies, data analysis, and flight simulation studies.
Development of improved modeling methods to provide increased fidelity of flight predictions for aircraft motions during flight in flow regimes with large nonlinearities requires improvements in test techniques for measuring and characterizing wind tunnel data. This paper presents a method for providing a measure of data integrity for static and forced oscillation test techniques. Data integrity is particularly important when attempting to accurately model and predict flight of today s high performance aircraft which are operating in expanded flight envelopes, often maneuvering at high angular rates at high angles-of-attack, even above maximum lift. Current aerodynamic models are inadequate in predicting flight characteristics in the expanded envelope, such as rapid aircraft departures and other unusual motions. Present wind tunnel test methods do not factor changes of flow physics into data acquisition schemes, so in many cases data are obtained over more iterations than required, or insufficient data may be obtained to determine a valid estimate with statistical significance. Additionally, forced oscillation test techniques, one of the primary tools used to develop dynamic models, do not currently provide estimates of the uncertainty of the results during an oscillation cycle. A method to optimize the required number of forced oscillation cycles based on decay of uncertainty gradients and balance tolerances is also presented.
The results of an analysis of wind-tunnel data for the effect of wave shape on local boundary layer flows and heat transfer are used to assess the feasibility of using corrugated panels on a Single-Stage-To-Orbit (SSTO) vehicle. In the flight assessment, available engineering design procedures are used to compute the inviscid and boundary layer flow for a given flight trajectory. The flight vehicle flow field calculations are then used in conjunction with wind-tunnel corrugated panel heating data correlations to examine the heating penalties associated with using corrugated panels at a number of locations on the vehicle. Severe heating penalties, as a result of the corrugations, were found over large areas of the windward surface. Maximum surface temperature penalties ranged from 100K to 500K and very large structural advantages for the corrugations would be required to override the heating penalties. Computed peak corrugation temperatures were within allowable limits of the equivalent smooth wall material for most leeward and side fuselage locations and corrugated panels will be most likely limited to these locations.