Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “programming model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Measurement and analysis of acoustic flight test data for two advanced design high speed propeller models

The recent test program, in which the SR-2 and SR-3 Prop-Fan models were acoustically tested in flight, is described and the results of analysis of noise data acquired are discussed. The trends of noise levels with flight operating parameters are shown. The acoustic benefits of the SR-3 design with swept blades relative to the SR-2 design with straight blades are shown. Noise data measured on the surface of a small-diameter microphone boom mounted above the fuselage and on the surface of the airplane fuselage are compared to show the effects of acoustic propagation through a boundary layer. Noise level estimates made using a theoretically based prediction methodology are compared with measurements.

Brooks, B. M.↗

Assessment of Ocean Wave Model used to Analyze the Constellation Program (CxP) Orion Project Crew Module Water Landing Conditions

Mr. Christopher Johnson, NASA's Systems Manager for the Orion Project Crew Module (CM) Landing and Recovery at the Johnson Space Center (JSC), and Mr. James Corliss, Project Engineer for the Orion CM Landing System Advanced Development Project at the Langley Research Center (LaRC) requested an independent assessment of the wave model that was developed to analyze the CM water landing conditions. A NASA Engineering and Safety Center (NESC) initial evaluation was approved November 20, 2008. Mr. Bryan Smith, NESC Chief Engineer at the NASA Glenn Research Center (GRC), was selected to lead this assessment. The Assessment Plan was presented and approved by the NESC Review Board (NRB) on December 18, 2008. The Assessment Report was presented to the NRB on March 12, 2009. This document is the final Assessment Report.

Smith, Bryan K.↗

Modeling Temporal Processes in Early Spacecraft Design: Application of Discrete-Event Simulations for Darpa's F6 Program

While the ability to model the state of a space system over time is essential during spacecraft operations, the use of time-based simulations remains rare in preliminary design. The absence of the time dimension in most traditional early design tools can however become a hurdle when designing complex systems whose development and operations can be disrupted by various events, such as delays or failures. As the value delivered by a space system is highly affected by such events, exploring the trade space for designs that yield the maximum value calls for the explicit modeling of time.This paper discusses the use of discrete-event models to simulate spacecraft development schedule as well as operational scenarios and on-orbit resources in the presence of uncertainty. It illustrates how such simulations can be utilized to support trade studies, through the example of a tool developed for DARPA's F6 program to assist the design of "fractionated spacecraft".

trade space exploration↗

A Modular Atmospheric Propagation Program (MAPP)

A computer model of the atmosphere has been developed that will solve a wide variety of lidar and atmospheric propagation problems. The lidar system calculations involve the prediction of path loss and lidar signal return for a variety of atmospheric conditions and lidar system configurations. The program contains a very large data base of absorption and attenuation coefficients for all of the naturally occurring gases and several gaseous pollutants such as S02, N02, NO, N20, 03, HCL, etc. The spectral range of this data base extends from the ultra-violet (1200 angstroms) through the infra-red. Several aerosol models are included in the program to account for the effects of this important scattering mechanism.

Wright, M. L.↗

An information maximization model of eye movements

We propose a sequential information maximization model as a general strategy for programming eye movements. The model reconstructs high-resolution visual information from a sequence of fixations, taking into account the fall-off in resolution from the fovea to the periphery. From this framework we get a simple rule for predicting fixation sequences: after each fixation, fixate next at the location that minimizes uncertainty (maximizes information) about the stimulus. By comparing our model performance to human eye movement data and to predictions from a saliency and random model, we demonstrate that our model is best at predicting fixation locations. Modeling additional biological constraints will improve the prediction of fixation sequences. Our results suggest that information maximization is a useful principle for programming eye movements.

NASA Discipline Neuroscience↗

Automatic documentation system extension to multi-manufacturers' computers and to measure, improve, and predict software reliability

The DOMONIC system has been modified to run on the Univac 1108 and the CDC 6600 as well as the IBM 370 computer system. The DOMONIC monitor system has been implemented to gather data which can be used to optimize the DOMONIC system and to predict the reliability of software developed using DOMONIC. The areas of quality metrics, error characterization, program complexity, program testing, validation and verification are analyzed. A software reliability model for estimating program completion levels and one on which to base system acceptance have been developed. The DAVE system which performs flow analysis and error detection has been converted from the University of Colorado CDC 6400/6600 computer to the IBM 360/370 computer system for use with the DOMONIC system.

Simmons, D. B.↗

An Integrated Approach to Laser Crystal Development

Norfolk State University has developed an integrated research program in the area of laser crystal development, including crystal modeling, crystal growth, spectroscopy, and laser modeling. This research program supports a new graduate program in Chemical Physics, designed in part to address the shortage of minority scientists.

Ries, Heidi R.↗

Free Radicals and Reactive Intermediates for the SAGE III Ozone Loss and Validation Experiment (SOLVE) Mission

This grant provided partial support for participation in the SAGE III Ozone Loss and Validation Experiment. The NASA-sponsored SOLVE mission was conducted Jointly with the European Commission-sponsored Third European Stratospheric Experiment on Ozone (THESEO 2000). Researchers examined processes that control ozone amounts at mid to high latitudes during the arctic winter and acquired correlative data needed to validate the Stratospheric Aerosol and Gas Experiment (SAGE) III satellite measurements that are used to quantitatively assess high-latitude ozone loss. The campaign began in September 1999 with intercomparison flights out of NASA Dryden Flight Research Center in Edwards. CA. and continued through March 2000. with midwinter deployments out of Kiruna. Sweden. SOLVE was co-sponsored by the Upper Atmosphere Research Program (UARP). Atmospheric Effects of Aviation Project (AEAP). Atmospheric Chemistry Modeling and Analysis Program (ACMAP). and Earth Observing System (EOS) of NASA's Earth Science Enterprise (ESE) as part of the validation program for the SAGE III instrument.

Anderson, James G.↗

Studies of Tenuous Planetary Atmospheres

In order to understand the physical and chemical processes which produce the tenuous planetary and planetary satellite (upper) atmospheres through interactions with their particle, field, and radiation environs, it is necessary to analyze remotely observed and spacecraft data with physically meaningful models. With this in mind, we have undertaken a coupled program of theoretical modeling and complementary data analysis regarding the global distributions of neutral and ionized gases in, and escape from, tenuous planetary atmospheres of Io and Europa. The theoretical models developed will have further applications to other tenuous atmospheres such as that of Pluto and Titan or the upper atmospheres of the terrestrial planets.

Combi, Michael R.↗

Improved Assessment of Recent Trends in NOx and VOC Emissions and Ozone Production Sensitivity Regimes Using Satellite Data

This presentation highlights results from a NASA Aura Science Team and Atmospheric Composition Modeling and Analysis Program (ACMAP) project which study the capability to observe and model trends in ozone (O3) production regimes using spaceborne sensors. Ultraviolet– visible (UV–Vis) tropospheric column satellite retrievals of formaldehyde (HCHO) (a proxy for volatile organic compound [VOC] reactivity) and nitrogen dioxide (NO2) (a proxy for nitrogen oxides [NOx]) are frequently used to investigate the sensitivity of O3 production to emissions of NOx and VOCs. There are challenges that come from using satellite-derived ratios of HCHO and NO2 (FNR) to study O3 production sensitivity with the largest uncertainties associated with specific spaceborne sensor’s retrieval biases and errors. This study quantifies the differences and improvements in satellite retrievals of O3 production sensitivity regimes using FNRs when moving from legacy polar orbiting satellites such as the Ozone Monitoring Instrument (OMI) onboard NASA’s Aura satellite and Ozone Mapping and Profiler Suite Nadir Mapper (OMPS-NM) onboard the NASA/NOAA Suomi-NPP platform to newer, higher spatiotemporal resolution satellite sensors TROPOspheric Monitoring Instrument (TROPOMI) and eventually the recently launched NASA geostationary sensor Tropospheric Emissions: Monitoring of Pollution (TEMPO). Furthermore, we investigate how using retrievals of NO2 and HCHO from these different satellites to constrain model predictions impacts the ability to accurately simulate O3 chemistry including chemical production regimes. To this end, we have conducted inverse model simulations, using the WRF-CMAQ-DDM data assimilation system at 12 km × 12 km, to constrain emissions of NOx and VOCs over the contiguous United States (CONUS) when assimilating OMI and TROPOMI retrievals of NO2 and HCHO. Two advantages of this are that we a) account for each satellite’s errors/biases in the emission estimation and b) update the prior profile to ensure that only radiance information is used for optimizing the emissions. This presentation will demonstrate: a) the varying accuracy of different satellite retrieved FNRs and ability to capture known sub-annual emission trends (e.g., seasonal, weekend/weekday) and emission anomalies during the COVID-19 lockdown of 2020, b) the differences and improvements in top-down emission estimates of NOx and VOCs when constrained by newer satellite sensors compared to legacy systems, and c) multi-sensor optimized emission estimates of summer-time NOx and VOCs between 2019-2021.

Data↗

Clustering Days with Similar Airport Weather Conditions

On any given day, traffic flow managers must often rely on past experience and intuition when developing traffic flow management initiatives that mitigate imbalances between the aircraft demand and the weather impacted airport capacity. The goal of this study was to build on recent efforts to apply data mining classification and clustering algorithms to vast archives of historical weather and air traffic data to identify patterns and past decisions that can ultimately inform day-of-operations decision-making. More specifically, this study identified similar weather impacted days at select U.S. airports, and analyzed the traffic management initiatives implemented on these representative days. The identification of the similar days was accomplished by applying a decision tree algorithm to the hourly Localized Aviation Model Output Statistics Program observations and the arrival delays for Newark Liberty International Airport. The branches from the trained decision tree were subsequently pruned to identify four weather conditions that resulted in medium to high delays for the arrivals scheduled to Newark in 2012. Using these weather conditions, four, daily airport-level Weather Impacted Traffic Index values were calculated using the Localized Aviation Model Output Statistics Program observations and the 2012 scheduled arrival counts from the FAAs Aviation System Performance Metric system. The four, daily Weather Impacted Traffic Index values for 2012 were subsequently clustered using an Expectation Maximization clustering algorithm, and nine unique types of weather days at Newark were identified. By far the most prominent type of day at Newark was a day associated with relatively good weather conditions, where there was little convective activity, winds were low, ceilings and visibility were high and there was little precipitation. Moderate levels of convective activity characterized the next most prominent type of day. Days with persistently high winds or low ceiling and visibility levels were relatively rare in 2012. Lastly, the frequency at which Ground Delay Programs, Ground Stops and Miles-in-Trail restrictions were implemented on each of the typical types of days at Newark were analyzed. Based on the results, it does appear as if the usage of Miles-in-Trail, Ground Delay Program and Ground Stop restrictions correlates well with the severity of the weather associated with each unique type of weather impacted day at Newark. Furthermore, the results demonstrate that it is feasible to use historical weather and air traffic archives to provide guidance on the types of traffic management restrictions to implement in response to the weather conditions impacting an airport.

traffic flow management↗

Clustering Days with Similar Airport Weather Conditions

On any given day, traffic flow managers must often rely on past experience and intuition when developing traffic flow management initiatives that mitigate imbalances between the aircraft demand and the weather impacted airport capacity. The goal of this study was to build on recent efforts to apply data mining classification and clustering algorithms to vast archives of historical weather and air traffic data to identify patterns and past decisions that can ultimately inform day-of-operations decision-making. More specifically, this study identified similar weather impacted days at select U.S. airports, and analyzed the traffic management initiatives implemented on these representative days. The identification of the similar days was accomplished by applying a decision tree algorithm to the hourly Localized Aviation Model Output Statistics Program observations and the arrival delays for Newark Liberty International Airport. The branches from the trained decision tree were subsequently pruned to identify four weather conditions that resulted in medium to high delays for the arrivals scheduled to Newark in 2012. Using these weather conditions, four, daily airport-level Weather Impacted Traffic Index values were calculated using the Localized Aviation Model Output Statistics Program observations and the 2012 scheduled arrival counts from the FAAs Aviation System Performance Metric system. The four, daily Weather Impacted Traffic Index values for 2012 were subsequently clustered using an Expectation Maximization clustering algorithm, and nine unique types of weather days at Newark were identified. By far the most prominent type of day at Newark was a day associated with relatively good weather conditions, where there was little convective activity, winds were low, ceilings and visibility were high and there was little precipitation. Moderate levels of convective activity characterized the next most prominent type of day. Days with persistently high winds or low ceiling and visibility levels were relatively rare in 2012. Lastly, the frequency at which Ground Delay Programs, Ground Stops and Miles-in-Trail restrictions were implemented on each of the typical types of days at Newark were analyzed. Based on the results, it does appear as if the usage of Miles-in-Trail, Ground Delay Program and Ground Stop restrictions correlates well with the severity of the weather associated with each unique type of weather impacted day at Newark. Furthermore, the results demonstrate that it is feasible to use historical weather and air traffic archives to provide guidance on the types of traffic management restrictions to implement in response to the weather conditions impacting an airport.

weather↗

Research on Spectroscopy, Opacity, and Atmospheres

I propose to continue providing observers with basic data for interpreting spectra from stars, novas, supernovas, clusters, and galaxies. These data will include allowed and forbidden line lists, both laboratory and computed, for the first five to ten ions of all atoms and for all relevant diatomic molecules. I will eventually expand to all ions of the first thirty elements to treat far UV and X-ray spectra, and for envelope opacities. I also include triatomic molecules provided by other researchers. I have also made CDs with Partridge and Schwenke's water data for work on UV stars. The line data also serve as input to my model atmosphere and synthesis programs that generate energy distributions, photometry, limb darkening, and spectra that can be used for planning observations and for fitting observed spectra. The spectrum synthesis programs produce detailed plots with the lines identified. Grids of stellar spectra can be used for radial velocity-, rotation-, or abundance templates and for population synthesis. I am fitting spectra of bright stars to test the data and to produce atlases to guide observers. For each star the whole spectrum is computed from the UV to the far IR. The line data, opacities, models, spectra, and programs are freely distributed on CDs and on my Web site and represent a unique resource for many NASA programs. I am now in full production of new line lists for atoms. I am computing all ions of all elements from H to Zn and the first 5 ions of all the heavier elements, about 800 ions. For each ion I treat as many as 61 even and 61 odd configurations, computing all energy levels and eigenvectors. The Hamiltonian is determined from a scaled-Hartree-Fock starting guess by least squares fitting the observed energy levels. The average energy of each configuration is used in computing scaled-Thomas-Fermi-Dirac wavefunctions for each configuration which in turn are used to compute allowed and forbidden transition integrals. These are multiplied into the LS allowed and forbidden transition arrays. The transition arrays are transformed to the observed coupling to yield the allowed and forbidden line lists. Results are put on the web as they are finished. Provided I get funding,there will be more than 500 million lines. I will then compare ion by ion, to all the laboratory and computed data in the literature and make up a working line list for spectrum synthesis and opacity calculations with the best available data. As the laboratory spectrum analyses are improved, I will redo the calculations with the new energy levels. My original plan when I started the new calculations was to run through all the atoms using my old Cray programs from the 1980's that were limited to 1100 x 1100 arrays in the Hamiltonian for each J. Then I would go back and rerun the more complicated cases with 3000 x 3000 arrays so that I could include many more configurations and more configuration interactions. At present I am limited to 61 even and 61 odd configurations and I try to include everything up through n = 9. The current program runs on Alpha workstations. I decided to test the big program on Fe I and Fe II to see whether there was any great difference in the low configurations compared to those from the Cray program. Besides increasing the number of E1 lines by a factor of 6 to 7.7 million, there was an unexpected result: the electric quadrupole transitions were 10 times stronger than before because the transition integrals are weighted by r(exp 2) ---they become very large for high n, and because there are numerous configuration interactions that mix the low and high configurations. As a check I was able to reproduce Carstang's (1962) lower results by running his three configurations with my program. Since my model atom is still only a subset of a real Fe II ion, the true quadrupole A values are probably larger than mine. The magnetic dipole lines are affected by the mixing but the overall scale does not change. Because of this scovery I decided that there was no point in computing the small array cases. I have been running with as many configurations as I can and with thousands of parameters in the Hamiltonian. The computer runs take much longer to set up and produce than I had expected. I have concentrated on redoing the low iron group spectra, especially to get data for supernova modelers. I have done only Ca I -- Zn I, Ca II -- Zn II, CU I -- Cu XXIX, Zn I - Zn XXX, for practice at high stages of ionization, C I, C II, S I, and CL I and Ag I for people who were working on the laboratory spectra. Check my web site kurucz.harvard.edu for current additions. My latest calculations have been for carbon I and sulphur I, and silicon I is under way using the same elaborate approach as for C I, which took many months to do. These line lists greatly increase the number of lines in the ultraviolet, in the visible, and especially in the infrared. They will increase the opacity in A, F, and G stars. They will account for many unidentified lines in the sun.

Kurucz, Robert L.↗

A user-oriented and computerized model for estimating vehicle ride quality

A simplified empirical model and computer program for estimating passenger ride comfort within air and surface transportation systems are described. The model is based on subjective ratings from more than 3000 persons who were exposed to controlled combinations of noise and vibration in the passenger ride quality apparatus. This model has the capability of transforming individual elements of a vehicle's noise and vibration environment into subjective discomfort units and then combining the subjective units to produce a single discomfort index typifying passenger acceptance of the environment. The computational procedures required to obtain discomfort estimates are discussed, and a user oriented ride comfort computer program is described. Examples illustrating application of the simplified model to helicopter and automobile ride environments are presented.

Leatherwood, J. D.↗

Microstructure Modeling of 3rd Generation Disk Alloy

The objective of this initiative, funded by NASA's Aviation Safety Program, is to model, validate, and predict, with high fidelity, the microstructural evolution of third-generation high-refractory Ni-based disc superalloys during heat treating and service conditions. This initiative is a natural extension of the DARPA-AIM (Accelerated Insertion of Materials) initiative with GE/Pratt-Whitney and with other process simulation tools. Strong collaboration with the NASA Glenn Research Center (GRC) is a key component of this initiative and the focus of this program is on industrially relevant disk alloys and heat treatment processes identified by GRC. Employing QuesTek s Computational Materials Dynamics technology and PrecipiCalc precipitation simulator, physics-based models are being used to achieve high predictive accuracy and precision. Combining these models with experimental data and probabilistic analysis, "virtual alloy design" can be performed. The predicted microstructures can be optimized to promote desirable features and concurrently eliminate nondesirable phases that can limit the reliability and durability of the alloys. The well-calibrated and well-integrated software tools that are being applied under the proposed program will help gas turbine disk alloy manufacturers, processing facilities, and NASA, to efficiently and effectively improve the performance of current and future disk materials.

Jou, Herng-Jeng↗

Modification, fabrication, testing and delivery of ITT model F4012 RP tube/coil assembly

Results of the improvement program for the ITT model F4012 RP image dissector tube and coil are presented. This program undertaken to improve the characteristics of this assembly to make it more accurate for the Large Space Telescope trackers' applications. Comparisons are given of the performance of the new components and the original design goals. Recommendations for further tests and/or design changes to further improve the F4012 tube/coil assembly performance are given.

Source record↗