Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “process cooling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Cooling Duct Analysis for Transpiration/Film Cooled Liquid Propellant Rocket Engines

The development of a low cost space transportation system requires that the propulsion system be reusable, have long life, with good performance and use low cost propellants. Improved performance can be achieved by operating the engine at higher pressure and temperature levels than previous designs. Increasing the chamber pressure and temperature, however, will increase wall heating rates. This necessitates the need for active cooling methods such as film cooling or transpiration cooling. But active cooling can reduce the net thrust of the engine and add considerably to the design complexity. Recently, a metal drawing process has been patented where it is possible to fabricate plates with very small holes with high uniformity with a closely specified porosity. Such a metal plate could be used for an inexpensive transpiration/film cooled liner to meet the demands of advanced reusable rocket engines, if coolant mass flow rates could be controlled to satisfy wall cooling requirements and performance. The present study investigates the possibility of controlling the coolant mass flow rate through the porous material by simple non-active fluid dynamic means. The coolant will be supplied to the porous material by series of constant geometry slots machined on the exterior of the engine.

Micklow, Gerald J.↗
NASA NTRS1990

Use of satellite data and modeling to assess the influence of stratospheric processes on the troposphere

Current research focused on the examination of the effects of ozone heating and Newtonian cooling on the linear stability of transient planetary waves. A finite difference numerical model was developed in which the basic state wind, temperature, and ozone distributions were constructed using ground-based and satellite data. Preliminary results indicate that ozone dynamics interaction may play a more important role in the stability and maintenance of planetary waves than previously thought, particularly in summer when the mean solar zenith angle is smallest and thus ozone heating largest. Examination of the finite amplitude interactions among radiation, ozone, and dynamics was carried out. Self-consistent, coupled equations governing the weakly nonlinear interactions are currently being analyzed to provide a better understanding of wave-mean flow interactions and ozone transport in a continuously stratified model of the troposphere-stratosphere coupled system.

Nathan, Terrence↗
NASA NTRSDate not supplied

The Additive Manufacturing Moment Measure (AM3) Approach to Predictions of Solid Cooling Rate and Time Above Melt

Qualification of a laser powder bed fusion additive manufacturing (LPBF-AM) process requires knowledge of the multi-scale material physics during the process, per part. As the LPBF-AM build occurs, each moment is influenced by the process history. Knowledge of the build sequence can be used to generate a discretized time-space-condition point field that when coupled with a nearest neighbors’ calculation results in a generalized and fully parallel process model computation. This GPU accelerated approach was developed for part-scale analysis of build files along with in-situ process monitoring sensor data and is termed the “Additive Manufacturing Moment Measure” (AM3). The AM3 approach will be presented and then used to evaluate an AM Bench relevant geometry with synchronized in-situ process data, ex-situ nondestructive evaluation, and optical microscopy observations. These comparisons permit a better understanding of how the process actions can affect the LPBF-AM build quality and the signals generated during in-situ process monitoring.

Additive Manufacturing↗
NASA NTRS2000

The Evolution of Tropospheric Temperature Field and its Relationship With The Onset of Asian Summer Monsoon

The mean state and year-to-year variations of the tropospheric temperature fields and their relationship with the establishment of the summertime East Asian monsoon (EAM) and the Indian monsoon (INM) are studied using the NCEP reanalysis data of 15 years (1982-1996). The results show that the seasonal shift of the South Asian High in the upper troposphere and the establishment of the EAM and the INM are closely related to the seasonal warming which causes a reversal of the meridional gradient of upper tropospheric mean temperature over the monsoon regions. On the average of 15 years, the reversal time of the temperature gradient in the EAM region (INM region) is concurrent with (one pentad earlier than) the onset time of the summer monsoon. In most years of the 15-year period, the reversal of temperature gradient coincides or precedes the onset time of the summer monsoon in both the EAM region and the INM region. The results suggest an important role of thermal processes on the establishment of the Asian monsoon. The contributors to the upper tropospheric warming over the EAM region are the strong horizontal warm advection and the diabetic heating against the adiabatic cooling due to upward motion. In the INM region, strong adiabatic heating by subsidence and the diabetic heating are major warming processes against the strong horizontal cold advection related to the persistent northwestlies to the southwestern periphery of the Tibetan Plateau. It appears that the early or late establishment of the Asian summer monsoon is not directly related to the differential warming near the surface.

He, H.↗
DOE OSTI2023

Additive manufacturing process parameter determination for a new Fe-C-Cu alloy

As a potential replacement for stainless steel alloys commonly used to print parts with laser powder bed fusion, a new Cu precipitation strengthened ferrous alloy, with composition Fe-0.2C-6Cu (wt%), was recently developed. This material is Co- and Ni-free, printable, has mechanical properties comparable to that of high strength stainless steels (approximately 1300 MPa UTS), and is cost-advantaged relative to existing low-alloy steels for additive manufacturing of parts with complex shapes. To gain traction for broader application, optimal laser powder bed fusion (LPBF) processing conditions to produce nearly defect-free parts without compromising mechanical strength are needed. Here, an optimal processing window based upon laser speeds that achieve minimal porosity was quantified via comparisons of measured melt pool penetration, scan speeds, printed material density and laser beam energy density on a commercial LPBF unit operating at 350 W, 80 μm hatch spacing, and 50 μm layer thickness based upon optimal parameters for 17-4PH. Furthermore, the window is 300 to 500 mm/s to achieve >99.8 % dense Fe-0.2C-6Cu (wt%) specimens. Other defects such as burning, spatter, and lack of fusion were also avoided in this window. The window was validated with in-situ synchrotron X-ray imaging that enabled visualization of the vapor cavity, melting, and solidification during a single laser track scan on a miniature powder bed sample. In addition, in-situ infrared imaging provided temperature fields, cooling rate and solidification range, and confirmed minimal printing defects and spatter within the processing window.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Heat and mass transfer in hygroscopic hydrogels

Sorption and desorption with hygroscopic hydrogels hold significant promise for thermal management, passive cooling, thermal energy storage, and atmospheric water harvesting. However, a comprehensive understanding of the energy and mass transport mechanisms in hygroscopic hydrogels remains missing, impeding accurate modeling and optimization. In this paper, we develop a model for the simultaneous vapor, water, and heat transfer in hygroscopic hydrogels during sorption and desorption processes. We show that by considering vapor diffusion in the hydrogel micropores, water diffusion in the polymer mesh, and heat transfer in the porous hydrogel, we can accurately capture experimentally observed thermally-driven desorption rates in these hydrogels. Furthermore, we consider three typical operating configurations of hydrogels and elucidate the differences in the transport mechanisms depending on the configuration. Finally, for each of these configurations, we identify key design parameters, including hydrogel thickness, hydrogel shear modulus, heat transfer coefficient, and thermal conductivity, and we parametrically show that by varying these parameters, a hygroscopic hydrogel can desorb up to 128.5%, 14.9%, 69.7%, and 9.6% more water, respectively, relative to the initial water content. This work provides a generic framework to model sorption and desorption processes in hygroscopic hydrogels which can guide the design and optimization in applications of thermal management, passive cooling, thermal energy storage, and atmospheric water harvesting with hydrogels.

36 MATERIALS SCIENCE↗
NASA NTRS1988

RF surface resistance of YBa2Cu3O(7-x) thin films

The excitement engendered by the discovery of the new T sub c oxide superconductors has led to much speculation about practical applications of thin films of these materials in digital and analog electronic devices. Most of these envisioned applications involve high frequency signals for which a detailed knowledge of the surface impedance of the novel superconductors is very important. We have measured the surface resistance of thin films of YBaCuO in the frequency range 0.5 less than f less than 17 GHz using a stripline-resonator method. The stripline procedure also was used to measure the surface resistance of high quality gold and aluminum films; the resistance values obtained agree with values predicted from the measured dc resistance using the Pippard formalism for the anomalous skin effect. The YBaCuO were produced by a multilayer deposition process. The films are formed by e-beam evaporation of 24 layers of Y, Ba, and Cu. Films with the highest transition temperature were obtained using yttria-stabilized zirconia (YSZ) substrates. After deposition, the films are transferred to a furnace where they are annealed in flowing O2 at 850 C for 2h. The furnace then is turned off and allowed to cool to 100 C in about 16 h. Auger profiling of the films made by this process shows that the concentrations of Y, Ba, Cu, and O are uniform to within 1 percent throughout the thickness of the film.

Source record↗
DOE OSTI2020

Experimental and Numerical Investigation of a Miniature Additively Manufactured Vortex Tube

Ranque–Hilsch vortex tubes are simple devices that can produce a cooling effect using compressed air. A key advantage of vortex tubes is the lack of moving solid parts; however, their efficiencies are relatively low. The present study focuses on the development of a miniature variable-diameter tube using additive manufacturing. A metal-based 3D printing technique was utilized to fabricate this vortex tube monolithically. Computational fluid dynamics simulations employing software STAR-CCM + with a compressible Reynolds-Averaged Navier–Stokes (RANS) approach and the elliptic-blending lag k-epsilon turbulence model have been applied to model thermofluid processes inside the vortex tube, to good agreement with the experiment. In conclusion, a temperature decrease of 13.3 °C and a cooling power of approximately 4 W were experimentally achieved with a pressure ratio of 4 in the air at normal conditions. This result shows promise for the goal of utilizing additive manufacturing to design and build complex-geometry vortex tubes intended for use with cryogenic fluids.

08 HYDROGEN↗
DOE OSTI2021

Heat and mass transfer during a sudden loss of vacuum in a liquid helium cooled tube - Part III: Heat deposition in He II

A sudden loss of vacuum can be catastrophic for superconducting particle accelerators. In such an event, air leaks into the liquid-helium-cooled accelerator beamline tube and condenses on its inner surface, causing rapid boiling of the helium and dangerous pressure build-up. Understanding the coupled heat and mass transfer processes is important for the design of the beamline cryogenic system. Our past experimental study on nitrogen gas propagating in a copper tube cooled by normal liquid helium (He I) has revealed a nearly exponential slowing down of the gas front. A theoretical model that accounts for the interplay of the gas dynamics and the condensation was developed, which successfully reproduced various key observations. However, since many accelerator beamlines are actually cooled by superfluid helium (He II) in which the heat transfer is via a non-classical thermal counterflow mode, we need to extend our work to the He II cooled tube. This paper reports our systematic measurements using He II and the numerical simulations based on a modified model that accounts for the He II heat-transfer characteristics. By tuning the He II peak heat-flux parameter in our model, we have reproduced the observed gas dynamics in all experimental runs. The fine-tuned model is then utilized to reliably evaluate the heat deposition in He II. Finallly, this work not only advances our understanding of condensing gas dynamics but also has practical implications to the design codes for beamline safety.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1951

Experimental Investigation of Air-Cooled Turbine Blades in Turbojet Engine. 7: Rotor-Blade Fabrication Procedures

An experimental investigation was conducted to determine the cooling effectiveness of a wide variety of air-cooled turbine-blade configurations. The blades, which were tested in the turbine of a - commercial turbojet engine that was modified for this investigation by replacing two of the original blades with air-cooled blades located diametrically opposite each other, are untwisted, have no aerodynamic taper, and have essentially the same external profile. The cooling-passage configuration is different for each blade, however. The fabrication procedures were varied and often unique. The blades were fabricated using methods most suitable for obtaining a small number of blades for use in the cooling investigations and therefore not all the fabrication procedures would be directly applicable to production processes, although some of the ideas and steps might be useful. Blade shells were obtained by both casting and forming. The cast shells were either welded to the blade base or cast integrally with the base. The formed shells were attached to the base by a brazing and two welding methods. Additional surface area was supplied in the coolant passages by the addition of fins or tubes that were S-brazed. to the shell. A number of blades with special leading- and trailing-edge designs that provided added cooling to these areas were fabricated. The cooling effectiveness and purposes of the various blade configurations are discussed briefly.

Long, Roger A.↗
NASA NTRS1975

Study on processing immiscible materials in zero gravity

An experimental investigation was conducted to evaluate mixing immiscible metal combinations under several process conditions. Under one-gravity, these included thermal processing, thermal plus electromagnetic mixing, and thermal plus acoustic mixing. The same process methods were applied during free fall on the MSFC drop tower facility. The design is included of drop tower apparatus to provide the electromagnetic and acoustic mixing equipment, and a thermal model was prepared to design the specimen and cooling procedure. Materials systems studied were Ca-La, Cd-Ga and Al-Bi; evaluation of the processed samples included the morphology and electronic property measurements. The morphology was developed using optical and scanning electron microscopy and microprobe analyses. Electronic property characterization of the superconducting transition temperatures were made using an impedance change-tuned coil method.

Reger, J. L.↗
NASA NTRS1986

The mathematical modeling of rapid solidification processing

The detailed formulation of and the results obtained from a continuum mechanics-based mathematical model of the planar flow melt spinning (PFMS) rapid solidification system are presented and discussed. The numerical algorithm proposed is capable of computing the cooling and freezing rates as well as the fluid flow and capillary phenomena which take place inside the molten puddle formed in the PFMS process. The FORTRAN listings of some of the most useful computer programs and a collection of appendices describing the basic equations used for the modeling are included.

Gutierrez-Miravete, E.↗
NASA NTRS1994

Constraints placed on the chondrule-forming process by merrihueite in the Mezoe-Madaras chondrite

A few unusual chondrules in the Mezoe-Madaras L3 chondrite contain the peralkaline mineral merrihueite, (K, Na)2(Fe, Mg)5Si12O30, formed by reaction of free silica in the chondrules with K, Na, Fe-rich nebular gas. Vapor fractionation was required to create chondrules poor in Al and rich in Si, and the fractionated condensate produced had to aggregate into protochondrules very promptly (on the order of hours or less) to prevent it from mixing with dust of more generalized composition in the nebula. The traditional paradigm for chondrule formation, involving a series of unrelated events (chemical fractionation of precursor dust; clumping of the dust; melting of the dust-clumps), is inadequate for making these chondrules. A rapid process, all stages of which are related, is required. We propose that this occurred during the cooling and contraction of the volume of hot gas created by a small transient high-energy event in the nebula, of unspecified nature. Microdroplets of silicate melt created by condensation from the cooling, contracting gas had velocity vectors directed toward the center of the volume. Coalescence occurred in the crowded central zone where the microdroplets converged. The Mezoe-Madaras merriihueite-bearing chondrules may have been formed by an atypically low-energy nebular event, which achieved the needed chemical fractionations by only partially vaporizing precursor dust. More commonplace chondrule types may have been created by the same basic process, but involving higher-energy events in which precursor dust was completely vaporized and recondensed.

Wood, John A.↗
NASA NTRS2007

Electron Beam Freeform Fabrication in the Space Environment

This viewgraph presentation describes the effect of microgravity on the fabrication of electron beam freeform (EBF) in aerospace environments. The contents include: 1) Electron Beam Freeform Fabrication (EBF3) Process Description; 2) Portable Electron Beam Freeform Fabrication System at NASA LaRC; 3) Electron Beam Freeform Fabrication in the Space Environment; 4) Effect of Gravity on Surface Tension; 5) Effect of Deposit Height on Cooling Path; 6) Microgravity Testing Aboard JSC's C-9; 7) Typical Test Flight Plates; 8) Direction and Height Trials for Process Control; 9) Effect of Wire Entry Direction into Molten Pool; 10) Microstructure of Single Layer EBF Deposits; 11) 0-g Deposit with Incorrect Standoff Distance; 12) Successful Demonstration of EBF in 0-g; and 13) Conclusion.

Taminger, Karen M.↗
DOE OSTI2023

Flow Induced Vibration Studies in Pressurized Helium Gas Cooling Channels

Production of metastable Technetium-99 (Tc-99m), a radioactive tracer that emits gamma rays, is vital to the medical imaging community. Tc-99m is extracted from the decay of Molybdenum-99 (Mo-99) which has a half-life of about 2-3 days. The work presented in this report is part of the NNSA’s mission to produce Mo-99 commercially, within the US, without the use of highly enriched uranium (HEU) in support of nonproliferation and global security. Los Alamos National Laboratory (LANL) is working with NorthStar Medical Radioisotopes (NMR) on their efforts to produce Mo-99 through the irradiation of Mo-100 targets using an electron beam. The NMR target comprises a stack of approximately 60-70 Mo-100 disks with diameter 24 mm and thickness 0.74 mm held in stainless steel laminations, each separated using 0.25 mm thick stainless steel spacers. The symmetric target stack is housed in an Inconel vessel with two Inconel windows on either side. Two electron accelerators are used to produce 40 MeV, 3.16 µA electron beams each that penetrate the Inconel windows and irradiate the Mo-100 disks. Approximately 90% of the total 250 kW beam power is deposited in the NMR target during the irradiation process. During irradiation, pressurized helium gas flows through 0.25 mm thin gaps between the disks cooling the beam window, target disks, disk laminations and spacers. Both NMR and LANL have found during cold testing of the target system (no heat deposition) that the Mo-100 disks undergo significant mass loss and disk breakage due to vibrations induced by the flowing helium gas. The mass loss is not only undesirable due to monetary loss from reduced final quantities of Mo-99, but also due to the hazards associated with radioactive material trapped in the cooling lines and particle filters. The effect of flow rate and target geometry on the flow induced vibrations need to be quantified, and recommendations provided to minimize this mass loss. This work describes LANL’s experimental characterization of the flow induced vibrations and disk mass loss in a reduced scale set-up containing 10 Mo-100 disks. We use high speed imaging, displacement measurements and microphone measurements combined with signal processing to estimate the vibration frequency of each disk. The effect of disk thickness, target fit and duration of testing on the mass loss is described. We find that in the current configuration of NMR targets, the vibrations and mass loss on the first disk are minimized, while those in the adjacent disks are highest. The microphone and high-speed image data show that increased flow rates and increased duration of testing increases vibration frequency and mass loss. The mass loss is due to both disk rotation and back and forth motion. There are visible wear marks on the disks with the highest mass loss. We also note that the current NMR window gap reduces flow induced vibrations compared to the previous smaller gaps. Longer duration testing will provide more data and verification for the findings presented in this report. The work will be continued in FY 24.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Light(ly)-coupled dark matter in the keV range: freeze-in and constraints

Dark matter produced from thermal freeze-out is typically restricted to have masses above roughly 1 MeV. However, if the couplings are small, the freeze-in mechanism allows for production of dark matter down to keV masses. We consider dark matter coupled to a dark photon that mixes with the photon and dark matter coupled to photons through an electric or magnetic dipole moment. We discuss contributions to the freeze-in production of such dark matter particles from standard model fermion-antifermion annihilation and plasmon decay. We also derive constraints on such dark matter from the cooling of red giant stars and horizontal branch stars, carefully evaluating the thermal processes as well as the bremsstrahlung process that dominates for masses above the plasma frequency. We find that the parameters needed to obtain the observed relic abundance from freeze-in are excluded below a few tens of keV, depending on the value of the dark gauge coupling constant for the dark photon portal model, and below a few keV, depending on the reheating temperature for dark matter with an electric or magnetic dipole moment. While laboratory probes are unlikely to probe these freeze-in scenarios in general, we show that for dark matter with an electric or magnetic dipole moment and for dark matter masses above the reheating temperature, the couplings needed for freeze-in to produce the observed relic abundance can be probed partially by upcoming direct-detection experiments.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Temperature-Controlled Reversible Formation and Phase Transformation of 3D Nanocrystal Superlattices Through In Situ Small-Angle X-ray Scattering

For decades, the spontaneous organization of nanocrystals into superlattices has captivated the scientific community. However, achieving direct control over the formation of the superlattice and its phase transformations has proven to be a grand challenge, often resulting in the generation of multiple symmetries under the same experimental conditions. Here, we achieve direct control over the formation of the superlattice and its phase transformations by modulating the thermal energy of a nanocrystal dispersion without relying on solvent evaporation. In this study, we follow the temperature-dependent dynamics of the self-assembly process using synchrotron-based small-angle X-ray scattering. When cooled below –24.5 °C, lead sulfide nanocrystals form micrometer-sized three-dimensional phase-pure body-centered cubic superlattices. When cooled below –35.1 °C, these superlattices undergo a collective diffusionless phase transformation that yields denser body-centered tetragonal phases. These structural changes can be reversed by increasing the temperature of the dispersion and may lead to the direct modulation of the optical properties of these artificial solids.

36 MATERIALS SCIENCE↗