Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

PDADMAC/PSS Oligoelectrolyte Multilayers: Internal Structure and Hydration Properties at Early Growth Stages from Atomistic Simulations

We analyze the internal structure and hydration properties of poly(diallyl dimethyl ammonium chloride)/poly(styrene sulfonate sodium salt) oligoelectrolyte multilayers at early stages of their layer-by-layer growth process. Our study is based on large-scale molecular dynamics simulations with atomistic resolution that we presented recently [Sánchez et al., Soft Matter 2019, 15, 9437], in which we produced the first four deposition cycles of a multilayer obtained by alternate exposure of a flat silica substrate to aqueous electrolyte solutions of such polymers at 0.1M of NaCl. In contrast to any previous work, here we perform a local structural analysis that allows us to determine the dependence of the multilayer properties on the distance to the substrate. We prove that the large accumulation of water and ions next to the substrate observed in previous overall measurements actually decreases the degree of intrinsic charge compensation, but this remains as the main mechanism within the interface region. We show that the range of influence of the substrate reaches approximately 3 nm, whereas the structure of the outer region is rather independent from the position. This detailed characterization is essential for the development of accurate mesoscale models able to reach length and time scales of technological interest.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Pressure-Thresholded Response in Cylindrically Shocked Cyclotrimethylene Trinitramine (RDX)

We demonstrate a strongly thresholded response in cyclotrimethylene trinitramine (RDX) when it is cylindrically shocked using a novel waveguide geometry. Using ultrafast single-shot multi-frame imaging, we demonstrate that <100 μm diameter single crystals of RDX embedded in a polymer host deform along preferential planes for >100 ns after the shock first arrives in the crystal. We use in situ imaging and time-resolved photoemission to demonstrate that short-lived chemistry occurs with complex deformation pathways. Using scanning electron microscopy and ultra-small-angle X-ray scattering, we demonstrate that the shock-induced dynamics leave behind porous crystals, with pore shapes and sizes that change significantly with shock pressure. A threshold pressure of ~12 GPa at the center of convergence separated the single-mode planar crystal deformations from the chemistry-coupled multi-plane dynamics at higher pressures. Our observations indicate preferential directions for deformation in our cylindrically shocked system, despite the applied stress along many different crystallographic planes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

A-Cation-Dependent Structure–Optical Property Relationships of Halide Perovskite Heterostructures with Complex Interfaces

Halide perovskite heterostructures offer promising interfacial interactions for energy conversion, yet challenges in synthesizing structurally well-defined systems limit detailed investigations into structure–property relationships. In this article, we report the synthesis of compositionally controlled 3D/3D and 3D/2D halide perovskite heterostructures using evaporation crystallization-polymer pen lithography (EC-PPL) and a single-particle analysis of their properties. By systematically varying A-site cation combinations and crystal dimensions, we show that heterointerfaces induce local lattice distortions that modulate vibrational dynamics and electron-phonon coupling. These interfacial effects result in significantly extended carrier lifetimes compared to compositionally similar pure phases. Raman spectroscopy, temperature-dependent photoluminescence, and power-dependent emission analysis reveal that localized structural modulations at the interface govern exciton-phonon interactions. These effects are magnified in smaller crystals due to increased interfacial contributions. Our findings highlight the critical role of interface-driven lattice control in tuning the optoelectronic properties of halide perovskites and provide design principles for engineering heterostructures in next-generation optoelectronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Multi-scale computer-aided design and photo-controlled macromolecular synthesis boosting uranium harvesting from seawater

By integrating multi-scale computational simulation with photo-regulated macromolecular synthesis, this study presents a new paradigm for smart design while customizing polymeric adsorbents for uranium harvesting from seawater. A dissipative particle dynamics (DPD) approach, combined with a molecular dynamics (MD) study, is performed to simulate the conformational dynamics and adsorption process of a model uranium grabber, i.e., PAO m -b-PPEGMA n , suggesting that the maximum adsorption capacity with atomic economy can be achieved with a preferred block ratio of 0.18. The designed polymers are synthesized using the PET-RAFT polymerization in a microfluidic platform, exhibiting a record high adsorption capacity of uranium (11.4 ± 1.2 mg/g) in real seawater within 28 days. This study offers an integrated perspective to quantitatively assess adsorption phenomena of polymers, bridging metal-ligand interactions at the molecular level with their spatial conformations at the mesoscopic level. The established protocol is generally adaptable for target-oriented development of more advanced polymers for broadened applications.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Aerosol jet printed capacitive strain gauge for soft structural materials

Soft structural textiles, or softgoods, are used within the space industry for inflatable habitats, parachutes and decelerator systems. Evaluating the safety and structural integrity of these systems occurs through structural health monitoring systems (SHM), which integrate non-invasive/non-destructive testing methods to detect, diagnose, and locate damage. Strain/load monitoring of these systems is limited while utilizing traditional strain gauges as these gauges are typically stiff, operate at low temperatures, and fail when subjected to high strain that is a result of high loading classifying them as unsuitable for SHM of soft structural textiles. For this work, a capacitance based strain gauge (CSG) was fabricated via aerosol jet printing (AJP) using silver nanoparticle ink on a flexible polymer substrate. Printed strain gauges were then compared to a commercially available high elongation resistance-based strain gauge (HE-RSG) for their ability to monitor strained Kevlar straps having a 26.7?kN (6?klbf) load. Dynamic, static and cyclic loads were used to characterize both types of strain monitoring devices. Printed CSGs demonstrated superior performance for high elongation strain measurements when compared to commonly used HE-RSGs, and were observed to operate with a gauge factor of 5.2 when the electrode arrangement was perpendicular to the direction of strain.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Studies of new perfluoroether elastomeric sealants

Channel and filleting sealants were developed successfully from cyano and diamidoxime terminated perfluoro alkylene ether prepolymers. The prepolymers were polymerized, formulated and tested. The polymers and/or formulations therefrom were evaluated as to their physical, mechanical and chemical properties (i.e., specific gravity, hardness, nonvolatile content, corrosion resistance, stress corrosion, pressure rupture resistance, low temperature flexibility, gap sealing efficiency, tensile strength and elongation, dynamic mechanical behavior, compression set, fuel resistance, thermal properties and processability). Other applications of the formulated polymrs and incorporation of the basic prepolymers into other polymeric systems were investigated. A cyano terminated perfluoro alkylene oxide triazine was formulated and partially evaluated. The channel sealant in its present formulation has excellent pressure rupture resistance and surpasses present MIL specifications before and after fuel and heat aging.

Basiulis, D. I.↗
DOE OSTI2026

Structural Heterogeneity and Hydrodynamics of an Intrinsically Disordered Protein Condensate

Biology demonstrates precise control over the free-energy landscape through the selective partitioning of biomacromolecules into membraneless organelles, enabling essential functions such as biochemical transformations, signaling cascades, and mechanical reinforcement. Although the function of these condensates depends on their underlying structure and hydrodynamics, molecular-scale information on these systems remains sparse. Here, in this study, neutron scattering is used to probe the organization and dynamics of the intrinsically disordered N-terminal domain of Galectin-3, an extracellular lectin responsible for facilitating liquid–liquid phase separation on the cellular surface, in both dilute and condensed phases. Dilute solutions contain isolated protein chains in equilibrium with mesoscopic clusters, whereas the condensed phase adopts a bicontinuous, microemulsion-like morphology. The dilute phase behavior is quantitatively described by coarse-grained polymer models from soft-matter physics, demonstrating their predictive power for complex biological proteins. At elevated concentrations, the proteins self-assemble akin to block copolymers, microphase separating through the aggregation of hydrophobic domains along the protein contour. The resulting condensate remains fluid-like despite a 25-fold increase in concentration; its internal hydrodynamics slow by only a factor of 3 relative to dilute protein chains. These results provide a molecular-level framework for how disordered proteins achieve both the structural complexity and dynamic fluidity of biomolecular condensates.

Carrick, Brian R. [Massachusetts Inst. of Technolo↗
DOE OSTI2020

Permeation of CO 2 and N 2 through glassy poly(dimethyl phenylene) oxide under steady- and presteady-state conditions

Glassy polymers are often used for gas separations because of their high selectivity. Although the dual-mode permeation model correctly fits their sorption and permeation isotherms, its physical interpretation is disputed, and it does not describe permeation far from steady state, a condition expected when separations involve intermittent renewable energy sources. To develop a more comprehensive permeation model, we combine experiment, molecular dynamics, and multiscale reaction–diffusion modeling to characterize the time-dependent permeation of N 2 and CO 2 through a glassy poly(dimethyl phenylene oxide) membrane, a model system. Simulations of experimental time-dependent permeation data for both gases in the presteady-state and steady-state regimes show that both single- and dual-mode reaction–diffusion models reproduce the experimental observations, and that sorbed gas concentrations lag the external pressure rise. The results point to environment-sensitive diffusion coefficients as a vital characteristic of transport in glassy polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2017

Implementation of a Tabulated Failure Model Into a Generalized Composite Material Model Suitable for Use in Impact Problems

The need for accurate material models to simulate the deformation, damage and failure of polymer matrix composites under impact conditions is becoming critical as these materials are gaining increased use in the aerospace and automotive communities. The aerospace community has identified several key capabilities which are currently lacking in the available material models in commercial transient dynamic finite element codes. To attempt to improve the predictive capability of composite impact simulations, a next generation material model is being developed for incorporation within the commercial transient dynamic finite element code LS-DYNA. The material model, which incorporates plasticity, damage and failure, utilizes experimentally based tabulated input to define the evolution of plasticity and damage and the initiation of failure as opposed to specifying discrete input parameters such as modulus and strength. The plasticity portion of the orthotropic, three-dimensional, macroscopic composite constitutive model is based on an extension of the Tsai-Wu composite failure model into a generalized yield function with a non-associative flow rule. For the damage model, a strain equivalent formulation is used to allow for the uncoupling of the deformation and damage analyses. For the failure model, a tabulated approach is utilized in which a stress or strain based invariant is defined as a function of the location of the current stress state in stress space to define the initiation of failure. Failure surfaces can be defined with any arbitrary shape, unlike traditional failure models where the mathematical functions used to define the failure surface impose a specific shape on the failure surface. In the current paper, the complete development of the failure model is described and the generation of a tabulated failure surface for a representative composite material is discussed.

polymer matrix composites↗
DOE OSTI2021

Enhanced piezoelectricity from highly polarizable oriented amorphous fractions in biaxially oriented poly(vinylidene fluoride) with pure β crystals

Piezoelectric polymers hold great potential for various electromechanical applications, but only show low performance, with |d 33 |< 30 pC/N. We prepare a highly piezoelectric polymer (d 33 = -62 pC/N) based on a biaxially oriented poly(vinylidene fluoride) (BOPVDF, crystallinity = 0.52). After unidirectional poling, macroscopically aligned samples with pure β crystals are achieved, which show a high spontaneous polarization (P s ) of 140 mC/m 2 . Given the theoretical limit of P s,β = 188 mC/m 2 for the neat β crystal, the high P s cannot be explained by the crystalline-amorphous two-phase model (i.e., P s,β = 270 mC/m 2 ). Instead, we deduce that a significant amount (at least 0.25) of an oriented amorphous fraction (OAF) must be present between these two phases. Experimental data suggest that the mobile OAF resulted in the negative and high d 33 for the poled BOPVDF. The plausibility of this conclusion is supported by molecular dynamics simulations.

36 MATERIALS SCIENCE↗
NASA NTRS2015

Fracture of Carbon Nanotube - Amorphous Carbon Composites: Molecular Modeling

Carbon nanotubes (CNTs) are promising candidates for use as reinforcements in next generation structural composite materials because of their extremely high specific stiffness and strength. They cannot, however, be viewed as simple replacements for carbon fibers because there are key differences between these materials in areas such as handling, processing, and matrix design. It is impossible to know for certain that CNT composites will represent a significant advance over carbon fiber composites before these various factors have been optimized, which is an extremely costly and time intensive process. This work attempts to place an upper bound on CNT composite mechanical properties by performing molecular dynamics simulations on idealized model systems with a reactive forcefield that permits modeling of both elastic deformations and fracture. Amorphous carbon (AC) was chosen for the matrix material in this work because of its structural simplicity and physical compatibility with the CNT fillers. It is also much stiffer and stronger than typical engineering polymer matrices. Three different arrangements of CNTs in the simulation cell have been investigated: a single-wall nanotube (SWNT) array, a multi-wall nanotube (MWNT) array, and a SWNT bundle system. The SWNT and MWNT array systems are clearly idealizations, but the SWNT bundle system is a step closer to real systems in which individual tubes aggregate into large assemblies. The effect of chemical crosslinking on composite properties is modeled by adding bonds between the CNTs and AC. The balance between weakening the CNTs and improving fiber-matrix load transfer is explored by systematically varying the extent of crosslinking. It is, of course, impossible to capture the full range of deformation and fracture processes that occur in real materials with even the largest atomistic molecular dynamics simulations. With this limitation in mind, the simulation results reported here provide a plausible upper limit on achievable CNT composite properties and yield some insight on the influence of processing conditions on the mechanical properties of CNT composites.

Jensen, Benjamin D.↗
DOE OSTI2026

Dataset_for_Conserved_macromolecular_architecture_of_Poplar_secondary_cell_walls_revealed_by_ssNMR_and_atomistic_modeling

This dataset contains solid-state 13C NMR data and atomistic molecular dynamics simulation files supporting the study of nanoscale secondary cell wall architecture across 13 genetically diverse Populus trichocarpa genotypes grown under uniform greenhouse conditions in 13C-enriched CO2 atmospheres (~89% 13C enrichment).The dataset contains two collections of solid-state 13C NMR data. (1) 200 MHz data (Bruker Avance III HD, 4 mm HX probe, 10 kHz MAS): raw Bruker TopSpin experiment folders and DMFIT-exported ascii spectra for selective and non-selective 1D 13C-13C spin diffusion experiments (3000 ms mixing) used to quantify inter-polymer spatial proximities, and short-mixing (1 ms) reference spectra used for polymeric abundance quantification by spectral deconvolution. (2) 600 MHz data (Bruker Avance III, 1.6 mm PhoenixNMR HXY probe, 30 kHz MAS): raw Bruker TopSpin experiment folders containing 2D CORD, 2D CP-INADEQUATE, and 13C/1H relaxation (T1, T1rho) experiments for all 13 genotypes, with processed Excel workbooks per experiment type. Molecular dynamics simulation code, coordinate files, and analysis scripts (NAMD/CHARMM/Python) for six atomistic cell wall models are included. Summarized ssNMR data are compiled into a single excel file and subjected to statistical analysis. Multivariate analysis code (PCA, Pearson correlation) and summary data are provided as excel worksheets and Jupyter notebooks (Python 3).

09 BIOMASS FUELS↗
DOE OSTI2023

Quantum bath augmented stochastic nonequilibrium atomistic simulations for molecular heat conduction

Classical molecular dynamics (MD) has been shown to be effective in simulating heat conduction in certain molecular junctions since it inherently takes into account some essential methodological components which are lacking in the quantum Landauer-type transport model, such as many-body full force-field interactions, anharmonicity effects and nonlinear responses for large temperature biases. However, the classical MD reaches its limit in the environments where the quantum effects are significant (e.g. with low-temperatures substrates, presence of extremely high frequency molecular modes). Here, we present an atomistic simulation methodology for molecular heat conduction that incorporates the quantum Bose–Einstein statistics into an “effective temperature” in the form of a modified Langevin equation. We show that the results from such a quasi-classical effective temperature MD method deviates drastically when the baths temperature approaches zero from classical MD simulations and the results converge to the classical ones when the bath approaches the high-temperature limit, which makes the method suitable for full temperature range. In addition, we show that our quasi-classical thermal transport method can be used to model the conducting substrate layout and molecular composition (e.g. anharmonicities, high-frequency modes). Anharmonic models are explicitly simulated via the Morse potential and compared to pure harmonic interactions to show the effects of anharmonicities under quantum colored bath setups. Finally, the chain length dependence of heat conduction is examined for one-dimensional polymer chains placed in between quantum augmented baths.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Controlled patterning of crystalline domains by frontal polymerization

Materials with hierarchical architectures that combine soft and hard material domains with coalesced interfaces possess superior properties compared with their homogeneous counterparts. These architectures in synthetic materials have been achieved through deterministic manufacturing strategies such as 3D printing, which require an a priori design and active intervention throughout the process to achieve architectures spanning multiple length scales. Here we harness frontal polymerization spin mode dynamics to autonomously fabricate patterned crystalline domains in poly(cyclooctadiene) with multiscale organization. This rapid, dissipative processing method leads to the formation of amorphous and semi-crystalline domains emerging from the internal interfaces generated between the solid polymer and the propagating cure front. The size, spacing and arrangement of the domains are controlled by the interplay between the reaction kinetics, thermochemistry and boundary conditions. Small perturbations in the fabrication conditions reproducibly lead to remarkable changes in the patterned microstructure and the resulting strength, elastic modulus and toughness of the polymer. Furthermore, this ability to control mechanical properties and performance solely through the initial conditions and the mode of front propagation represents a marked advancement in the design and manufacturing of advanced multiscale materials. Drawing inspiration from biological systems in which structural complexity develops through dissipative reaction–diffusion processes, this study explores a transformative synthetic manufacturing strategy aimed at harnessing the principles underpinning morphogenic growth, unlocking new avenues for advanced materials design and fabrication. Synthetic coupled reaction-transport processes offer a versatile yet relatively underexplored method to manipulate the spatial attributes of synthetic materials10. Here we introduce an innovative manufacturing approach based on frontal ring-opening metathesis polymerization (FROMP) that draws parallels with morphogenic growth and development, enabling the formation of patterned microstructures within polymeric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Scaling relationships for the elastic moduli and viscosity of mixed lipid membranes

The elastic and viscous properties of biological membranes play a vital role in controlling cell functions that require local reorganization of the membrane components as well as dramatic shape changes such as endocytosis, vesicular trafficking, and cell division. These properties are widely acknowledged to depend on the unique composition of lipids within the membrane, yet the effects of lipid mixing on the membrane biophysical properties remain poorly understood. Here, we present a comprehensive characterization of the structural, elastic, and viscous properties of fluid membranes composed of binary mixtures of lipids with different tail lengths. We show that the mixed lipid membrane properties are not simply additive quantities of the single-component analogs. Instead, the mixed membranes are more dynamic than either of their constituents, quantified as a decrease in their bending modulus, area compressibility modulus, and viscosity. While the enhanced dynamics are seemingly unexpected, we show that the measured moduli and viscosity for both the mixed and single-component bilayers all scale with the area per lipid and collapse onto respective master curves. This scaling links the increase in dynamics to mixing-induced changes in the lipid packing and membrane structure. More importantly, the results show that the membrane properties can be manipulated through lipid composition the same way bimodal blends of surfactants, liquid crystals, and polymers are used to engineer the mechanical properties of soft materials, with broad implications for understanding how lipid diversity relates to biomembrane function.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Understanding and Manipulating Counterion Condensation within Charged Polymer Electrolytes for Selective and Low Resistant Membrane Separations

Polymeric ion-exchange membranes are found at the heart of numerous electrochemical systems spanning separations (electrodialysis and membrane capacitive deionization) and energy conversion and storage (flow batteries, fuel cells, and electrolyzers). The ion-exchange membrane separators need to be ion conducting but electron insulating, and in many scenarios selective for a particular ion to conduct. Because of their polymeric nature, the molecular architectures of ion-exchange membranes lack the molecular precision found in many inorganic materials. Plus, they contain numerous structural defects that impede ionic transport. As a result of their poor structure, it has been difficult to carefully probe the underlying physics that governs ion transport in ion-exchange membranes. We investigated counterion condensation phenomena in ion-exchange membranes and correlated it to bulk ionic charge transport and selectivity in precisely defined and long-range ordered materials afforded through the principles of directed self-assembly. A multi-faceted approach spanning i.) advanced metrology, two-dimensional atomic force microscopy, x-ray scattering, and ion-exchange equilibria, and ii.) molecular simulations (classical molecular dynamics and ab-inito molecular dynamics) that bridge multiple time and length scales, were employed to correlate the extent of counterion condensation to ionic conductivity and selectivity. After uncovering the extent of the condensation phenomena in this project, new macromolecular chemistries were employed to manipulate the ion pairing interactions of the condensed counterions to tethered ions on the polymer backbone so more facile and selective conduction rates can be attained. The research has aided in the rational design of polymeric ion-exchange membrane separators with high current density for electrochemical systems and subsequently better energy efficiency.

36 MATERIALS SCIENCE↗
NASA NTRS2017

Incorporation of Failure Into an Orthotropic Three-Dimensional Model with Tabulated Input Suitable for Use in Composite Impact Problems

The need for accurate material models to simulate the deformation, damage and failure of polymer matrix composites under impact conditions is becoming critical as these materials are gaining increased use in the aerospace and automotive communities. The aerospace community has identified several key capabilities which are currently lacking in the available material models in commercial transient dynamic finite element codes. To attempt to improve the predictive capability of composite impact simulations, a next generation material model is being developed for incorporation within the commercial transient dynamic finite element code LS-DYNA. The material model, which incorporates plasticity, damage and failure, utilizes experimentally based tabulated input to define the evolution of plasticity and damage and the initiation of failure as opposed to specifying discrete input parameters such as modulus and strength. The plasticity portion of the orthotropic, three-dimensional, macroscopic composite constitutive model is based on an extension of the Tsai-Wu composite failure model into a generalized yield function with a non-associative flow rule. For the damage model, a strain equivalent formulation is used to allow for the uncoupling of the deformation and damage analyses. In the damage model, a semi-coupled approach is employed where the overall damage in a particular coordinate direction is assumed to be a multiplicative combination of the damage in that direction resulting from the applied loads in various coordinate directions. For the failure model, a tabulated approach is utilized in which a stress or strain based invariant is defined as a function of the location of the current stress state in stress space to define the initiation of failure. Failure surfaces can be defined with any arbitrary shape, unlike traditional failure models where the mathematical functions used to define the failure surface impose a specific shape on the failure surface. In the current paper, the complete development of the failure model is described and the generation of a tabulated failure surface for a representative composite material is discussed.

Impact↗