SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
We performed a branching ratio measurement of the most intense gamma rays in the decay of 111Ag. The sample was harvested at Argonne National Laboratory and measured at Texas A&M with the same technique as we used in our previous measurements. We made two samples and were able to measure both of them. The data is currently under analysis.
Alternating current circuit breaker and direct current engine contactors for space - vacuum interrupter and contact material, interrupter and actuator design, and test facility selection
Applications such nonproliferation, post-detonation forensics, spent-fuel assay, reactor burnup and design, as well as astrophysics, rely on the accurate description of the neutron interaction with unstable fission products. Current neutron-induced cross-section descriptions for these nuclei are either non-existent or based on simplified assumptions, leading to unquantified impacts on predicted cross-sections. The goal of the Realistic Reaction Evaluations for Fission Products Off Stability (RREFPOS) project is to develop a reproducible methodology leading to a more predictive and realistic new set of evaluated nuclear data, improving the reliability of applications involving fission products off stability. The current report documents the activities related to the RREFPOS project in its first year, corresponding to the Fiscal Year of 2025 (FY25).
Published data on the emission of charged particles following nuclear muon capture are extremely limited. In addition to its interest as a probe of the nuclear response, these data are important for the design of some current searches for lepton flavor violation. This work presents momentum spectra of protons and deuterons following μ- capture in aluminum. It is the first measurement of a muon capture process performed with a tracking spectrometer. A precision of better than 10% over the momentum range of 100–190MeV/c for protons is obtained; for deuterons of 145–250MeV/c the precision is better than 20%. The observed partial yield of protons with emission momenta above 80MeV/c (kinetic energy 3.4MeV) is 0.0322 ± 0.0007(stat) ± 0.0022(syst) per capture, and for deuterons above 130MeV/c (4.5MeV) it is 0.0122 ± 0.0009(stat) ± 0.0006(syst). Extrapolating to total yields gives 0.045 ± 0.001(stat) ± 0.003(syst) ± 0.001(extrapolation) per capture for protons and 0.018 ± 0.001(stat) ± 0.001(syst)± 0.002(extrapolation) for deuterons, which are the most precise measurements of these quantities to date.
Use of corrosion-resistant cladding can greatly extend the design life of structural components in many advanced reactor systems. However, there are currently no ASME design rules for cladded components to guard against creep-fatigue failure and ratcheting strain accumulation in elevated temperature nuclear service. This paper, presented in two parts, addresses this gap by proposing a design strategy for cladded components that do not require long-term testing of clad materials. The proposed approach relies on approximate design analysis methods for two types of clad materials—a soft clad that creeps much faster than and has lower yield stress than the class A base material and a hard clad that creeps much slower than and has higher yield stress than the class A base material. Part I discusses the approximate analysis strategies for the clad materials—treat a soft clad as perfectly compliant and a hard clad as linear elastic—and Part II develops a complete set of design rules for each of the two types of cladded components. In conclusion, finite element analyses of representative high temperature reactor components show that the proposed design analysis methods can bound the design quantities in soft cladded components and approximate the design quantities in hard cladded components.
The Grizzly code is being developed to address degradation issues in nuclear reactor structures and components. For light-water reactors, Grizzly currently has capabilities to simulate degradation processes and their effects on structural integrity in two key areas: reactor pressure vessels (RPVs) and reinforced concrete structures. This report documents improvements made to Grizzly’s ability to address both of these structural systems. For RPVs, the reduced-order models (ROMs) used in fracture mechanics calculations have been expanded to allow their application over a broader range of the parameter space than was permitted by the previous models. The ROMs currently used in Grizzly for the evaluation of flaws that are fully embedded within the RPV (as opposed to surface-breaking flaws) are based on a model that is known to be conservative, indicating higher stress intensity factors than would be obtained from direct simulations. A more accurate model that eliminates these excess conservatisms has been recently included in the American Society of Mechanical Engineers Boiler and Pressure Vessel Code but was not applicable for flaws near the RPV surface, which is where the most critical flaws are usually located. That model has recently been extended for increased applicability in this near-surface region. The ROMs for embedded flaws in the Grizzly code have been expanded to include these recent extensions, which permit their use in a much broader set of cases than previously possible. Direct 3D simulations have been used to check these ROMs and have shown good agreement in most cases, although there are still some cases that need further investigation. There are considerable benefits to using these these more accurate and less conservative ROMs for embedded flaws. On a benchmark probabilistic fracture mechanics problem tested here, the conditional probability of fracture initiation computed for a population of flaws in a single plate in an RPV decreased by over a factor of 3. To address aging in reinforced concrete structures, a capability to simulate multiple degradation mechanisms, including alkali-silica reaction and radiation-induced volumetric expansion has been developed in Grizzly over the past several years. This had previously been demonstrated on laboratory-scale specimens but not on full-scale nuclear concrete structures with reinforcement. To demonstrate the applicability of Grizzly to the analysis of large-scale structures of interest, a full 3D model of a representative reinforced concrete structure, including a complex arrangement of reinforcing bars, was developed and demonstrated in Grizzly.
As the nuclear energy industry considers ways to achieve improved economics in the current fleet of light-water reactors (LWRs), one possible approach is to operate each cycle longer. This causes a greater portion of the fuel to be burned and reduces the frequency of outages, which ultimately reduces the cost to operate the reactor. However, this also leads to higher burnup fuels than have traditionally been allowed in these reactors. There are concerns about integrity of high-burnup (HBu) fuel, especially during accident conditions such as loss-of-coolant accidents (LOCAs), as shown by Capps et al. To investigate these concerns, advanced modeling and simulation capabilities are under development to determine the susceptibility of HBu fuel to fuel fragmentation, relocation, and dispersion (FFRD). Improvements have previously been made to fuel performance capabilities to model these phenomena more accurately; multiphysics simulations have also been conducted to determine the power and burnup histories of the HBu fuel, which are needed as inputs to the fuel performance calculations. Most recently, new statistical approaches have been developed to identify a subset of fuel rods that have greater FFRD susceptibility, reducing the total number of fuel performance simulations required.
Over the past several decades, the United States (U.S.) and other countries have done important research and development in advanced nuclear energy technologies, both fission and fusion. The urgency of our current climate, energy, and security needs have prompted a concerted effort by innovators, investors, and the public sector to transition from research and development (R&D) to demonstration and commercialization—to cross the proverbial “valley of death.” The stakes are high: humanity needs clean energy options, and the failure of any promising alternative will lower our odds of success. The process of moving an innovation into use has often been described in phases that begin with early research and end with deployment at scale. Between those two phases lies an area often referred to as the “valley of death” because it can require a long period of time, large investments, and often includes significant challenges related to regulation, standardization, and entering markets already structured around incumbent technologies. What can we learn from recent experience with fission to inform our path forward with fusion? At least five key lessons rise to the top: 1) Set bold targets; 2) Empower the private sector; 3) Engage with regulators and the public; 4) Address costs and markets; and 5) Deliver results. Here, this editorial will consider each of these in turn.
During the vitrification of nuclear waste, hazardous and radioactive emissions are generated from the feed-to-glass conversion reactions, in addition to discharges from forced air bubbling and air inleakage. Although the major gaseous emissions are water vapor, nitrogen, and carbon dioxide, various monitored environmental pollutants are also released, such as nitrogen oxides or sulfur dioxide. In addition, reactions between organics and nitrates in the feed may also form products of incomplete combustion such as carbon monoxide and acetonitrile. Although off-gas emissions are commonly measured during both laboratory- and pilot-scale melter testing, no predictive tool is currently available to a priori estimate the composition of gaseous emissions during nuclear waste vitrification. This work forms a basis for the development of such predictive tool by measuring gas evolution from a broad range of simulated low-activity waste melter feeds using evolved gas analysis data and developing correlations between the feed and off-gas compositions. Using reaction stoichiometry and regression analysis, we demonstrate that next to the content of nitrogen and organic carbon in the feed, the gaseous emissions are affected by the feed reduction-oxidation conditions – the more the feed is reduced, the less nitrogen monoxide, and more carbon monoxide and acetonitrile evolves. In conclusion, the results presented in this work provide a first step towards reducing the amount of expensive physical melter testing and the regression analysis provides a simple tool for rapid optimization of feed composition with respect to off-gas composition.
Small modular reactors (SMRs) are reactor designs producing less than 300 MWe and are generally planned for deployment as multimodule nuclear power plants. The possibility of factory-manufactured, flexibly sized plants expands the opportunities for nuclear power to different communities and industries, including manufacturing plants that currently utilize fossil fuels to produce both steam and electricity. This paper examines the feasibility of coupling a NuScale SMR with a midsize pulp and paper mill in the Southeastern United States. A steady-state mill model was developed in Aspen HYSYS, based on real data from the operation of the mill, and modified it to include the SMR while maintaining steam quality requirements and making as few changes as possible to existing equipment. Dynamic plant models were also developed Dymola to demonstrate possible plant conditions, using three configurations. Preliminary results suggest that, while SMR coupling is physically feasible, its economic feasibility is limited by the differences in steam and electricity demands. Because of limitations in the amount of steam the mill can take from the SMR, sizing the SMR for the plant’s steam demand may result in an electricity deficit, or vice versa. Furthermore, dynamic analyses show that the addition of a thermal storage system could reduce such deficits, but this entails its own challenges. Each plant must determine the best configuration and control scheme for itself, based on its electricity and heat needs, including the peak duration and intensity for both. Ultimately, an implementation of SMRs with manufacturing processes would benefit from partnering with a local utility to purchase excess electricity generated by the SMR. This will help manufacturing facilities meet their environmental and cost-savings goals, in addition to meeting the need for cost-effective baseload power across the United States.
Refractory carbide nuclear fuel has been one of the most promising fuel candidates for space nuclear propulsion due to its high melting point, temperature stability, and compatibility in a hot hydrogen environment. In this study, U x Zr 1-x C y fuel was produced by means of a carbothermic reduction process in different UC compositions including 5,10, 20, and 30 at.% UC in the fuel compound. The powder feedstock was consolidated via direct current sintering with densities up to 97% of the theoretical density. The samples with different U x Zr 1-x C y compositions were exposed to hot hydrogen at 2600 K for a cumulative time of 300 min. The samples were characterized by SEM, XRD, density, and measured for mass losses. The high-density samples displayed improved performance in hot hydrogen by minimizing porous sites and reducing areas of direct contact with hydrogen gas, leading to reduced mass losses. Variations in sample density proved to induce large changes in mass loss rates, increasing them up to 90%. The compositions with higher UC content reported the largest mass losses in the study. The loss of uranium occurred primarily at the surfaces exposed to the hot hydrogen where changes in the lattice constant confirmed losses exceeding 50% of the initial UC content in higher compositions, specifically to U 0.3 Zr 0.7 C y . XRD analyses revealed the presence of UH 3 in U 0.3 Zr 0.7 C y suggesting that metallic uranium formed inside the sample as a product of carbon losses. High-density U x Zr x-1 C y fuel with UC concentrations at or below 20 at.% UC exhibited stability and negligible density changes in a high temperature hydrogen environment.
The weak interactions of neutrinos with other Standard Model particles are well described within the Standard Model of particle physics. However, modern accelerator-based neutrino experiments employ nuclei as targets, where neutrinos interact with bound nucleons, turning a seemingly simple electroweak process into a complex many-body problem in nuclear physics. At the time of writing this Encyclopedia of Particle Physics chapter, neutrino-nucleus interactions remain one of the leading sources of systematic uncertainty in accelerator-based neutrino oscillation measurements. This chapter provides a pedagogical overview of neutrino interactions with nuclei in the medium-energy regime, spanning a few hundred MeV to several GeV. It introduces the fundamental electroweak formalism, outlines the dominant interaction mechanisms - including quasielastic scattering, resonance production, and deep inelastic scattering - and discusses how nuclear effects such as Fermi motion, nucleon-nucleon correlations, meson-exchange currents, and final-state interactions modify observable cross sections. The chapter also presents a brief survey of the foundational and most widely used theoretical models for neutrino-nucleus cross sections, together with an overview of current and upcoming accelerator-based neutrino oscillation experiments that are shaping the field. Rather than targeting experts, this chapter serves as a primer for advanced undergraduates, graduate students, and early-career researchers entering the field. It provides a concise foundation for understanding neutrino-nucleus scattering, its relevance to oscillation experiments, and its broader connections to both particle and nuclear physics.
Sealed-canister dry storage of aluminum-clad spent nuclear fuel (ASNF) generated by research reactors is an alternative to current storage and disposition pathways as directed by the U.S. Department of Energy. The major challenge faced for this storage approach is radiolytic H 2 generation, including from the aluminum (oxy)hydroxide layers on the surface of ASNF. Experimental and modeling activities have been carried out to characterize the radiolytic yield as part of a DOE-sponsored research program to develop the technical basis for ASNF dry storage. The G-value is a commonly way to report results of radiolysis testing and is defined as the radiolytic yield of a species (e.g. molecular hydrogen) per unit radiation energy deposited into the material system. An independent technical review of the ASNF dry storage technical basis performed by Pacific Northwest National Laboratory raised questions about differences in G-value definitions used for experiments on ASNF surrogates consisting of aluminum samples with adherent (oxy)hydroxides compared to G-values reported in prior literature and how the magnitudes compared between different studies. Material systems resembling ASNF pose complications for measuring/defining G-values to predict the evolution of H 2 in a sealed canister, including i) accounting for radiolytic yields potentially arising from multiple sources, i.e., residual free (vapor), physisorbed, and chemisorbed/chemically bound waters; ii) deciding what portions of the multi-material system to include in the absorbed energy (radiation dose) calculation, considering possible energy exchange between materials as well as measurement limitations, and iii) capturing variations in G-value associated with non-linear yield vs. dose curves and/or dependence on the cover gas. This report summarizes previous literature information on radiolytic H 2 generation and associated G-values from mixed-material systems (generally oxides in contact with water or organic compounds) and from (oxy)hydroxides/hydrates to compare with the definitions and values for ASNF surrogate samples containing adherent aluminum (oxy)hydroxides.
As the nuclear energy industry considers ways to achieve improved economics in the current fleet of light-water reactors (LWRs), one possible approach is to operate each cycle for longer durations. This causes a greater portion of the fuel to be burned and reduces the frequency of outages, which ultimately reduces the cost to operate the reactor. However, this also leads to higher burnup fuels than has traditionally been allowed in these reactors. Thus, there are concerns about integrity of high-burnup (HBu) fuel, especially during accident conditions such as loss-of-coolant accidents (LOCAs), as shown by Capps et al.. To investigate these concerns, advanced modeling and simulation capabilities are being leveraged to determine the susceptibility of HBu fuel to fuel fragmentation, relocation, and dispersion (FFRD). Improvements have previously been made to fuel performance capabilities to more accurately model these phenomena; multiphysics simulations have also been conducted to determine the power and burnup histories of the HBu fuel, which are needed as inputs for the fuel performance calculations. Most recently, new statistical approaches have been developed to identify a subset of fuel rods that have greater FFRD susceptibility, reducing the total number of fuel performance simulations required. Prior LOCA simulations have relied on the TRACE systems code, which can model the core and primary loop during accident conditions. TRACE includes many models for various aspects of the primary loop, but two sets of models are important for this report. First, TRACE uses a lumped-fuel approach for modeling the core. This approximates the ~50,000 fuel rods in the core with a much smaller number of rods. The rods can be lumped in various ways as determined by the user. For example, one lumped rod may be used to represent all rods in an assembly, sometimes with an additional rod representing the hottest fuel rod. However, due to runtime constraints and complexity of modeling, a more common approach is to group several assemblies or larger regions of the core into single lumped rods. These lumping schemes apply not only to fuel rods but to flow channels as well. Second, TRACE has several different models for treating decay heat, ranging from pregenerated decay heat curves based on an ANSI/ANS-5.1 standard (hereinafter abbreviated simply as ANSI) to explicit time-dependent heat inputs from the user. None of these models account for differences in isotopics between different rods, which is an approximation the work in this report seeks to eliminate. This report focuses on the implementation of coupled decay heat capabilities in the Virtual Environment for Reactor Applications (VERA) code suite to address a gap identified in previous LOCA simulations. This constitutes an improvement for both the lumped-fuel and decay heat models in TRACE. VERA has been developed to perform high-fidelity, whole-core multiphysics simulations for LWRs. Previously, during the Consortium for Advanced Simulation of LWRs (CASL) program, the emphasis was on providing accurate steady-state analysis—with a secondary focus on reactivity insertion accident (RIA) analysis—to address operational challenges in the nuclear energy industry. Under the Department of Energy (DOE) Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, these capabilities are being extended to a broader range of transient analyses with the goal of quantifying the risk of fuel failures such as FFRD. To properly model such conditions with VERA, decay heat calculations have been integrated with the multiphysics to enable rod-by-rod thermal hydraulic (TH) conditions to be driven by the decay heat in long-running accidents such as LOCAs.
After being used in nuclear installations, depleted fuel can still be highly reactive and must be handled securely to prevent any radiological or criticality concerns. In particular, spent fuel from use in nuclear power reactors must be stored and transported in specifically designed containers using neutron absorber materials to prevent criticality. Various neutron absorber material types exist and are manufactured by various entities, as thoroughly described in the Handbook of Neutron Absorber Materials for Spent Nuclear Fuel Storage and Transportation Applications written by EPRI. Presently, one of the most modern and most widely used types of neutron absorber material contains particles of boron carbide, or B 4 C, embedded in aluminum matrix: Boralcan, manufactured by Rio Tinto. It is very important for the community to know as much as possible about such neutron absorber materials. Therefore, in the recent years, a US Department of Energy National Nuclear Security Administration–Nuclear Criticality Safety Program funded project initiated design of an experiment that places Boralcan neutron-absorbing plates in an established critical assembly using low-enriched uranium fuel at the Sandia Pulsed Reactor Facility/Critical Experiments (SPRF/CX) apparatus at Sandia National Laboratories. The goal of the experiment is to produce high-quality benchmark data to submit to the International Criticality Safety Benchmark Evaluation Project (ICSBEP), for use in validating calculational tools and nuclear data by criticality safety analysts. The project, named IER-554, is currently in its final design stage, following a successful preliminary design. In the work documented in the design study, ten critical configurations using Boralcan neutron absorber plates were designed, and the experiment was proven to be feasible, with a predicted low k eff uncertainty around 100 pcm. An overview of the modeled cutout of the critical assembly with a Boralcan plate is shown in Figure 1, representing one of the configurations planned for the critical experiments. Before the plates are inserted in the critical assembly, it is necessary to know more about their composition and uniformity. This summary focuses on the plate characterization plans. Each plate will undergo (1) neutron transmission measurements at different locations to determine the 10 B areal density and (2) an in-depth x-ray computed tomography (XCT) examination to obtain the exact Sizes and distribution of the B4C powder particles inside the plates. In parallel, plate modeling studies are performed with a goal to determine the validity of the currently used approximation of modeling the neutron absorber plates as a homogeneous mixture of Aluminum 1100 alloy and B4C— instead of explicitly modeling the B4C particles. By using the experimental 10 B areal density measurements, and the exact size and location of the B4C particles obtained by XCT, a plate model can theoretically be built that reproduces the plate with extremely high fidelity. The results of this modeling study could increase the confidence of the criticality safety community in its modeling methods when using this type of neutron absorber material, and the industry could use these validations to change the boron loading credit limits from the U.S. Nuclear Regulatory Commission standard review plan for dry cask storage of spent nuclear fuel. The modeling calculations are performed with SCALE 6.3.0 using the KENO V.a sequence for criticality calculations with the ENDF/B-VIII.0 continuous-energy cross section library.
The overarching goal of this Light Water Reactor Sustainability Program–supported research and development project is to provide planning tools and comprehensive guidance to utilities considering or undertaking full nuclear plant modernization. The results of this research will provide the nuclear industry with a comprehensive and usable solution, including guidance, lessons learned, methods, and planning tools. This research is currently working to provide guidance on digitalization and information automation to enable the evolution of data to information, insight, and action—thereby allowing utilities to operate safely and cost-competitively with all other electrical generation sources. Light Water Reactor Sustainability Program researchers have also recently started investigating how human and technology integration principles, information automation, and digitalization enable data evolution. These researchers are currently in the process of validating the use of System-Theoretic Process Analysis to define high-level safety constraints in the United States Nuclear Regulatory Commission’s problem identification and resolution process (i.e., a plant compliance information gathering activity). The next step in this research, which is described in the following sections of this report, is to map out data evolution in a use case to identify inefficiencies in another aspect of plant compliance information gathering and communication activities—event investigations and root cause analyses.
Not Available
Explore the source record for details and available documents.