Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Microstructural features underpinning the mechanical behavior of powder metallurgy Cr-based alloys

Refractory materials such as Cr-based alloys offer the potential of enhanced elevated temperature performance but have been limited by their poor formability. However, powder metallurgy has been shown to be a viable pathway to fabricate these alloys. Nanophase separation sintering (NPSS) in particular has been used in the literature to accelerate the densification of powder metallurgy Cr- and W-based alloys. Here, we explore microstructure evolution during NPSS in a binary Cr 85 Ni 15 alloy consolidated via (i) cold pressing & pressureless sintering and (ii) hot isostatic pressing followed by hot extrusion & hot upsetting, and the role of these different processing routes on resulting material properties. The alloy lacked room temperature tensile ductility regardless of consolidation process, with multi-length scale characterization, including scanning electron microscopy, transmission electron microscopy, atom probe tomography, X-ray diffraction, and uniaxial tensile testing, revealing that brittleness was due to intrinsically poor Cr grain boundary cohesion. Tensile testing conducted at 760 °C showed marked strength reduction for the extruded & upset (94 %) condition compared to the pressed & sintered (18 %). The formation of orthorhombic CrNi 2 intermetallics functioned as precipitate strengtheners and prevented elevated temperature softening in the pressed and sintered condition. The findings offer foundational insights into aiding the future development of Cr-based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure refinement of hot deformed Dy-free NdFeB magnets through a novel cold sintering approach by pressure-assisted spark plasma sintering

Anisotropic fine-grained Dy-free NdFeB high-performance magnets were produced using a novel cold sintering approach by pressure-assisted spark plasma sintering (SPS). The NdFeB nanocrystalline ribbon powders were subjected to cold sintering below 450 °C using pressure-assisted SPS, followed by hot deformation at 710 °C and 810 °C via SPS. Results indicate that cold sintering below 450 °C effectively restricts grain growth in the NdFeB magnets, yielding sub-100 nm scale grains across both fine-grained regions and most coarse-grained regions. The refined grain structure achieved through cold sintering allows for a lower hot deformation temperature as compared with the magnet by conventional sintering, as finer grains allow easier deformation and grain sliding/rotation. This process produces a highly fine-grained and anisotropic microstructure to achieve high magnetic performance (i.e., high intrinsic coercivity, remanence, and maximum energy product) in the magnets. The cold sintering (at 350 °C) and lower hot deformation temperatures required (e.g., 710 °C) help control grain coarsening and limit grain size that is commensurate with the size of a single magnetic domain of the Nd 2 Fe 14 B magnetic matrix phase, resulting in high intrinsic coercivity (H ci =11.4 kOe). Furthermore, the reduced hot deformation temperature mitigates the formation of coarse grain bands, leading to improved magnetic properties, specifically an increased remanence (B r = 14.3 kGs) and a high maximum energy product ((BH) max = 48 MGOe). In conclusion, cold sintered hot deformed NdFeB magnet also shows good thermal stability with reversible temperature coefficient α(B r )= -0.097 %/K and α(H ci )= -0.616 %/K at elevated temperatures up to 400 K.

Cold Sintering↗
DOE OSTI2020

Effects of irradiation spectrum on the microstructural and mechanical properties of bulk metallic glasses

Zr 52.5 Cu 17.9 Ni 14.6 Al 10 Ti 5 (BAM-11) and Cu60Zr 20 Hf 10 Ti 10 bulk metallic glass (BMG) specimens were ion irradiated to characterize and compare their irradiation induced microstructural and mechanical property evolution. For the ion irradiations, samples of each BMG were exposed to 9 MeV Ni 3+ and 5.5 MeV C + ions to a midrange (~1.5 μm depth) dose of 0.5 displacements per atom (dpa) at temperatures ranging from room temperature to 360 °C in order to examine potential effects associated with low (5.5 MeV C) and high (9 MeV Ni) average primary knock on energies. BAM-11 BMG samples were also irradiated by neutrons (E > 0.1 MeV) at ~70 °C to a fluence of 1.4 × 10 20 n/cm 2 (dose of 0.1 dpa). Importantly, no pronounced irradiation spectrum effects were observed for the nanoindentation mechanical properties of the two BMGs following ion irradiation. However, significant softening was observed in the BAM-11 BMG sample irradiated by neutrons, while annealing of the unirradiated samples led to a marked increase in hardening. Finally, results of the nanoindentation experiments indicate that softening is caused by irradiation induced creation of free volume defects, while the hardening is caused by their annihilation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural changes of proton irradiated Hastelloy-N and in situ micropillar compression testing of one single grain at different local damage levels

Here, in situ micropillar compression was used to study the deformation of proton-irradiated Hastelloy-N at different damage levels. Multiple pillars were prepared from a single domain along the cross-section of 2.5 MeV proton-irradiated Hastelloy-N. Depending on the location of micropillars, the critical resolved shear stress was obtained as a function of local damage levels. Such an approach eliminates the variation of yield stress due to the difference in the Schmid factor. Microstructural characterization showed that irradiation hardening is contributed by complicated defect structures, including (a) dislocation loops with many in corduroy-like alignments, (2) dislocations pile up, and (3) Cottrell atmosphere. Silicon atoms are found to segregate at dislocation lines and loops and form complicated Cottrell cloud patterns. The critical resolved shear stress, $t_{crss}$, and hardening exponents were both extracted as a function of displacements per atom values up to 2.3. There was a 60% increase in $t_{crss}$ at the highest damage level.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Hydrogen permeation in iron-chromium-aluminum (FeCrAl) alloys and the effects of microstructure and surface oxide

Iron–chromium–aluminum (FeCrAl) class alloys are candidates for use as cladding for accident-tolerant fuels and moderators. In this context, hydrogen isotope permeation in FeCrAl alloys is an important material property. Here, in the present work, the apparent permeability, effective diffusivity, and apparent solubility of hydrogen in the FeCrAl alloys C26M and Kanthal D (KD) were measured with gas-driven hydrogen permeation. Permeation measurements were conducted at temperatures of 400 to 700 °C and at gas-driven pressures from 1 to 100 kPa. In particular, the effect of grain size on hydrogen transport was studied with KD samples with three different microstructures: nanocrystalline (NC), ultra-fine grained (UFG), and coarse-grained (CG). The UFG and NC specimens had higher apparent activation energies (73.4 kJ mol -1 and 65.2 kJ mol -1 , respectively) for hydrogen permeability than the CG sample (46.9 kJ mol -1 ). An aluminum oxide layer formed on the primary- and secondary-side surfaces of all samples subjected to permeation experiments which demonstrated the propensity of FeCrAl alloys to form these innate oxide permeation barriers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Characterization of the microstructure of yttrium hydride under proton irradiation

High moderation per unit volume solid moderator materials like yttrium hydride (YH x ) are necessary for compact nuclear microreactors. However, the phase stability and hydrogen transport processes of YH x under high-temperature irradiation are largely unknown. Proton irradiation was conducted on YH x at 300 °C and 580 °C to 0.2 dpa using 1 MeV or 2 MeV protons in a high-vacuum environment. The hydrogen concentration was determined before and after irradiation using elastic recoil detection analysis, and microstructural evolution was examined via post-irradiation scanning transmission electron microscopy and Raman spectroscopy. Dislocation loops and cavities were observed in all conditions; their distribution was correlated with the bombarding proton energy and ion irradiation temperature. This work revealed that hydrogen retention is proportional to the formation of traps for hydrogen gas atoms and identified pathways for hydrogen release. The relative contributions of bulk or fast diffusion paths, such as grain boundaries, delamination boundaries, and stacking faults are discussed; the primary mechanisms of hydrogen loss are likely based on diffusion, ruling out artefacts of the experimental design. In conclusion, the study suggests proton irradiation may be a strong surrogate to study hydrogen transport in hydride moderator materials under irradiation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Microstructurally validated stable and predictable swelling in low-enriched uranium monolithic U-10Mo fuel mini-plates

Qualification of the low-enriched uranium (LEU) monolithic U-10 wt%Mo (U-10Mo) plate-type fuel system requires a demonstration of a stable and predictable fuel swelling behavior over the anticipated operating conditions of the United States high-performance research reactors (USHPRRs) selected for conversion to LEU operation. This will allow each reactor to develop appropriate safety margins that will retain fuel element lifetime coolability. Additionally, the fuel system must maintain performance attributes when fabricated at a commercial scale. The Mini-plate 1 experiment represents the first irradiation test of commercially fabricated miniaturized monolithic LEU U-10Mo fuel plates. Here, the swelling behavior within this experiment was compared against that of historical fuel developmental tests to reveal that the commercially fabricated fuel performed within the current recommended U-10Mo swelling model's predictions. Additionally, the fuel microstructural evolution was evaluated to link initial conditions to subtle variations detected in the swelling response, providing validation and confidence that the fuel system is robust.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Microstructure and crystallographic texture of high frequency electric resistance welded X65 pipeline steel

Here, microstructure and crystallographic texture and their correlation with impact toughness of high-frequency electric resistance welded (HF-ERW) X65 Grade pipeline steel have been investigated. X65 base metal after HF-ERW has formed a typical hourglass-shaped weld joint with four different regions, including the thermomechanical-affected zone (TMAZ), fine-grained heat affected zone (FGHAZ), coarse-grained heat affected zone (CGHAZ), and bondline (Weld Zone). X65 base metal shows prominent (113) [110] and (112) [110] texture components due to thermomechanical-controlled processing. TMAZ depicted random texture with a minor intensity of Cube component (001)[110] due to the partial recrystallization during welding. In the FGHAZ and CGHAZ, near the bondline, the base metal texture has been converted to rotated Goss (110) [110], Goss (110) [001], and rotated cube (001) [110] due to the recrystallization of the austenite and the shear deformation in the austenite temperature range. A high density of {100} and {110} cleavage planes is observed in the CGHAZ, which is often found to be the fracture location for the impact toughness testing.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Hierarchical microstructures and deformation behavior of laser direct-metal-deposited Cu–Fe alloys

Cu25Fe75 and Cu50Fe50 (nominal composition, at. %) alloys were fabricated using laser direct metal deposition (DMD) based additive manufacturing technique. These alloys exhibit hierarchical microstructures with bi-phasic Cu and Fe dendrites that contain nanoscale precipitates of varying sizes and structures. In the Cu25Fe75 alloy, Fe dendrites contained nanoscale, coherent, metastable BCC Cu and semi-coherent FCC Cu precipitates while the Cu matrix had nanoscale, coherent, metastable FCC Fe precipitates. In the Cu50Fe50 alloy, Fe dendrites only contained nanoscale semi-coherent FCC Cu precipitates while the Cu matrix had nanoscale coherent metastable FCC Fe precipitates. Both alloys exhibited enhanced flow strengths in the range of 750 – 980 MPa and significant plasticity, in compression. Here, the Cu25Fe75 alloy had lower yield strength than Cu50Fe50 alloy but higher maximum compressive strength due to higher strain hardening resulting from slightly coarser dendrites with hierarchy of nanoscale precipitation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure evolution, enhanced aging kinetics, and mechanical properties of AA7075 alloy after friction extrusion

In the present study we utilized Friction Extrusion (FE) a solid phase processing technique to produce fully consolidated dense 5 mm rods of AA7075 alloy. The combination of large shear stresses and temperatures at the tool-billet interface during the FE process resulted in the formation of dynamically recrystallized ~2.0 μm equiaxed grains and fine uniformly distributed stable η (MgZn 2 ) precipitates ~25–100 nm in size. Formation of such a microstructure resulted in lower solutionizing temperature and times (flash annealing) as compared to the conventionally extruded counterparts. Here we demonstrate for the first time that the solutionizing times for the T6 heat treatment of AA7075 can be reduced by three times using this FE process. In addition to being an energy efficient process, FE also serves to improve the performance of AA7075 alloys by retaining their strength while enhancing the ductility of the material. The tensile data for samples that were flash annealed and artificially aged after FE processing showed exceptional increase in ultimate tensile strength by over 19% and yield strength by over 59%, compared with an as-FE-processed sample.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructures and deformation mechanisms of the medium-entropy alloy (NiCoCr) 76 (Ni 6 AlTi) 3

Here the microstructures and deformation mechanisms of the f.c.c. medium-entropy alloy (MEA) (NiCoCr) 76 (Ni 6 AlTi) 3 has been analyzed after various thermo-mechanical treatments. The solutionized, single-phase MEA, which had a grain size of 93.4 ± 31.9 μm, was cold-rolled (CR) to a 80% thickness reduction after which it showed both a high yield strength (YS) of 1539 MPa and a high ultimate tensile strength (UTS) of 1602 MPa, but an elongation to failure, ε, of only 16%. The CR MEA was then subjected to one of two heat treatments: (1) the CR MEA was recrystallized at 1100°C for 24 h, which produced a single-phase material with 85 ± 61.7 μm grain size that exhibited a much lower YS and UTS of 364 MPa and 747 MPa, respectively, but a much greater ε of 73%; and (2) the MEA was aged at 700°C for 24 h, which produced a fine-grained (1.1 ± 0.9 μm) material and a high volume fraction (0.35) of 12 nm dia. L1 2 nanoparticles that exhibited an excellent combination of strength and ductility, viz., YS~1501 MPa, UTS~1651 MPa, elongation ~26%. The grain boundary strengthening and precipitation strengthening were together estimated to account for ~58% of the YS in the latter material. After deformation, the recrystallized MEA contained numerous stacking faults and a Taylor lattice structure containing domain boundaries and microbands, while the aged MEA exhibited numerous stacking faults and sheared particles. The density of low-angle grain boundaries (LAGBs) in the recrystallized MEA increased by 100 times to 2.2 × 10 –1 μm/μm 2 while the density of CSL Σ3 n boundaries decreased by 71% to 7.8 × 10 –3 μm/μm 2 after deformation. In contrast, the density of LAGBs in the aged MEA increased by 5 times to 2.6 μm/μm 2 while the density of CSL Σ3 n boundaries decreased by 57% to 0.6 μm/μm 2 after deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of Re and Al additions on the microstructure and mechanical properties of Nb-18Ti-12W alloy

Microstructure and mechanical properties at 25–1200 °C of new refractory alloys, Nb-18Ti-12W (NTW), Nb-18Ti-12W-5Re (NTW-R) and Nb-18Ti-12W-5Re-1Al (NTW-RA), all compositions are in atomic percent, are reported. The alloys are developed as an alternative to a denser, more expensive and difficult-to-process refractory alloy WC-3009. After production by arc melting and hot isostatic pressing at 1400 °C, 207 MPa for 3 h, the alloys have a BCC crystal structure with the average grain size of ~150–200 μm and contain low volume fraction of (Ti,N)-rich precipitates near grain boundaries. NTW shows excellent malleability at all studied temperatures. Its yield stress at 25 °C, 1000 °C and 1200 °C is 874 MPa, 353 MPa and 202 MPa, respectively. The NTW-R and NTW-RA alloys are stronger at all the studied temperatures; however, they lack in compression ductility at 25 °C. As a result, extensive deformation twinning and formation of intergranular voids precede the fracture of these two alloys at 25 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Correlation between Interface Microstructure and Bond Strength of Al6061/Al6061 HIP-Bonded Plates for Fuel Cladding Application

The effects of hot isostatic pressing (HIP) processing parameters on microstructure and bond strength of Al6061/Al6061 plate interfaces were systemically investigated at the micro- and nanoscale. The HIP bonding of the two aluminum plates was performed at four temperatures: 350°C, 400°C, 450°C, and 560°C. The results reveal the formation of micron scaled Mg 2 Si precipitate and uniform nano scaled Mg 2 Al 2 O 5 oxide at the interface. The formation of Mg 2 Al 2 O 5 is closely associated with the fast bulk diffusion of Mg from the Al matrix to the amorphous Al 2 O 3 /Al interface and subsequent reaction between Mg and Al 2 O 3 . Finally, the highest and lowest bond strengths were observed in samples HIP bonded at 450°C and 350°C, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Chain rigidity controlled aggregation ability and solid-state microstructures for efficient stretchable conjugated polymer films

Stretchable conjugated polymer films with good electrical performance under mechanical deformation are highly desirable for soft electronics. However, the mechanical and electrical properties of these films, particularly in conjugated polymer:elastomer blends, are not fully understood at molecular level. Here, this study explores the relationships among molecular structure, aggregation ability, film microstructure, and the electrical/mechanical properties of three diketopyrrolopyrrole-based conjugated polymers (P1, P2, P3) with decreasing backbone rigidity and their corresponding polymer:elastomer blends. The most flexible polymer P3 shows strong aggregation, which forms highly crystalline fibers to produce fragile neat film and produces large isolated crystallites restricting charge transport in blend film. As chain rigidity increases, the P1 and P2 polymers show weaker aggregation, and produce smaller crystallites in neat films with enhanced ductility. P1 and P2 based blend films display nanocrystallites polymer networks with dispersed elastomer domains. As a result, we achieved near-constant charge mobility before and after stretching under 50 % strain for P2-based blend films with well-controlled pathways for both charge transport and energy dissipation. This study demonstrates the critical role of backbone rigidity in regulating the properties of stretchable conjugated polymer films, paving the way for more reliable and deformable materials in soft electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Reverse scaling of a bonded-sphere DEM model: Formulation and application to lignocellulosic biomass microstructures

We explore scaling laws for adapting a bonded-sphere discrete element method (BS-DEM) model developed for woody structural mechanics at the millimeter scale to model the mechanics of realistic lignocellulosic biomass microstructures. Two scaling approaches, i.e., the reverse coarse graining (RCG) and equivalent bulk behavior (EBB), are proposed based on the classical mechanics principles and assessed in the single-particle compression and rectangular cuboid block tension tests. The EBB approach is recommended for BS-DEM models with general 3D geometries and is applied to simulate the microindentation test on a realistic microscale pinewood specimen. Simulations are performed to elucidate the impact of specimen thickness and loading position on the specimen’s force–deformation behavior. Furthermore, the range of Young’s modulus obtained from the calibrated BS-DEM simulations can match the experimental measurements. This is the first-of-its-kind study that has explored scale-bridging modeling approaches in biomass micromechanics and has proposed solutions based on BS-DEM models in the microscale.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

On the quantitative characterization of weld microstructures

Here, a new technique to quantify grain shape and grain boundary curvature in the fusion zone (FZ) and the heat-effected zone (HAZ) of refractory metals and alloys has been developed. The application of this technique to quantify the effect of welding speed on these microstructural characteristics in simulated molybdenum welds is highlighted in this study. A 50% increase in weld speed more than doubles the fraction of grain segments in the fusion zone with orientations between 00 to 300 to the normal to the welding direction, with a corresponding 50% decrease in the fraction of grain segments oriented along the welding direction. This increase in weld speed also results in a reduction in grain size from approximately 120 µm to 84 µm along the WD at the FZ centerline. Grain boundary curvature is negative near the weld centerline and the edge of the fusion zone, indicating that with increasing distance from the weld centerline, the grain segments progressively rotate towards a direction normal to the welding direction at both locations. Presence of regions with relatively straight grain segments indicated by curvatures close to zero were identified in between the weld centerline and the edge of the FZ at all weld speeds.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Scalable Solution-Processed Electrolyte Membranes with Optimized Microstructure for High-Performance Protonic Ceramic Electrochemical Cells

Proton-conducting electrochemical cells (PCECs) are promising for efficient hydrogen production, but achieving dense, uniform, thin electrolyte layers remains a key challenge, particularly for scalable fabrication. Here, we present a solution-processed deposition approach with a mechanistically optimized slurry for uniform electrolyte formation. By tailoring particle size distribution, solid loading, and solvent/additive balance, we regulated wetting behavior and evaporation kinetics of the electrolyte slurry to promote homogeneous electrolyte particle packing. These features facilitate tight grain boundary contact and early stage neck growth during sintering, eliminating residual porosity, and improving mechanical integrity. The resulting ∼15 μm thick electrolyte shows high density, strong electrode adhesion, and stable interfaces outperforming the previously reported spray-based fabricated electrolyte by about 31% at 600 °C in FC mode. Single cells deliver 0.962 W cm –2 at 600 °C in fuel cell mode and 1.31 A cm –2 at 1.3 V in electrolysis mode, maintaining robust performance over 100 h with negligible degradation (≤0.02% h –1 ) in each mode. Scale-up to 2.5 cm diameter substrates confirmed reproducible densification and geometric stability. This work demonstrates a cost-effective, scalable route where control over particle-fluid interactions and drying dynamics enables a superior electrolyte microstructure and high PCEC performance.

dense microstructure↗
DOE OSTI2025

Revealing the evolution of order in materials microstructures using multi-modal computer vision

The development of high-performance materials for microelectronics, energy storage, and extreme environments depends on our ability to describe and direct property-defining microstructural order. Our present understanding is typically derived from laborious manual analysis of imaging and spectroscopy data, which is difficult to scale, challenging to reproduce, and lacks the ability to reveal latent associations needed for mechanistic models. Here, we demonstrate a multi-modal machine learning (ML) approach to describe order from electron microscopy analysis of the complex oxide La 1−x Sr x FeO 3 . We construct a hybrid pipeline based on fully and semi-supervised classification, allowing us to evaluate both the characteristics of each data modality and the value each modality adds to the ensemble. We observe distinct differences in the performance of uni- and multi-modal models, from which we draw general lessons in describing crystal order using computer vision.

36 MATERIALS SCIENCE↗