Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “grain texture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Correlating the Microstructure of Thin Films of Poly(5,5-Bis(3-Dodecyl-2-Theinyl)-2,2-Bithiophene With Charge Transport: Effect of Dielectric Surface Energy And Thermal Annealing

Poly[5,5{prime}-bis(3-dodecyl-2-thienyl)-2,2{prime}-bithiophene] (PQT-12) is a conjugated polymer that shows promising performance ({micro} > 0.1 cm{sup 2}/V s) as a semiconductor for thin-film electronics. The electrical properties of PQT-12 thin films can vary by over 3 orders of magnitude depending on the chemistry of the substrate onto which they are deposited and on annealing conditions. The highest mobility is obtained in films annealed on a dielectric treated with a self-assembled monolayer of octadecyltrichlorosilane (OTS). Polymeric thin films were processed from either a solution of dissolved PQT-12 molecules in 1,2-dichlorobenzene or from a nanoparticle dispersion of the polymer in the same solvent (nPQT-12). In addition, the substrate surface chemistry was altered by spin coating on a bare SiO{sub 2} dielectric or on SiO{sub 2} treated with OTS. The microstructure of the two forms of polymer, as characterized using specular and grazing x-ray diffraction in addition to rocking curves, was compared and correlated with the electrical performance of the films as active layers in thin-film transistors. As-spun films of nPQT-12 are always more crystalline than those of PQT-12, independent of substrate chemistry. Consequently, carrier mobility in as-spun films is higher in nPQT-12 than in PQT-12. The presence of the OTS monolayer at the polymer/dielectric interface increases crystallinity of both PQT-12 and nPQT-12, without significantly affecting their texture. After annealing, the mobility in PQT-12 films and nPQT-12 films is comparable. Annealing causes the polymer films on OTS to undergo crystallite growth in the direction normal to the substrate. In nPQT-12, growth of the crystalline coherence length in the {pi}-{pi} stacking direction (i.e., parallel to the substrate and in the direction of charge transport) occurs as well. The mobility increase in nPQT-12 on OTS upon annealing is thus attributed to the higher crystallinity of the film. In PQT-12 films deposited on OTS on the other hand, annealing causes a decrease in the out-of-plane misorientation of neighboring crystallites without any significant grain growth in the plane of the film. The mobility increase in PQT-12 on OTS upon annealing is attributed to a better intergrain connectivity, in agreement with electrical modeling of the transistor characteristics using a mobility edge model.

36 MATERIALS SCIENCE↗

Magnetotransport properties of c-axis oriented La{sub 0.7}Sr{sub 0.3}MnO{sub 3} thin films on MgO-buffered SiO{sub 2}/Si substrates

c-axis oriented La{sub 0.7}Sr{sub 0.3}MnO{sub 3} (LSMO) films on MgO-buffered SiO{sub 2}/Si substrates were prepared, and their texture, microstructure, and magnetotransport properties were studied and compared to epitaxial LSMO/MgO (001) and polycrystalline LSMO/SiO{sub 2}/Si films. c-axis oriented MgO buffer layers were obtained on amorphous SiO{sub 2} layer through rf sputter deposition at low substrate temperature and consequent postannealing processes. In situ pulsed laser deposition-grown LSMO films, deposited on the MgO layer, show strong c-axis texture, but no in-plane texture. The c-axis oriented LSMO films which are magnetically softer than LSMO/SiO{sub 2}/Si films exhibit relatively large low field magnetoresistance (LFMR) and sharper MR drop at lower field. The large LFMR is attributed to a spin-dependent scattering of transport current at the grain boundaries.

36 MATERIALS SCIENCE↗

Eulerian hydrocode modeling of a dynamic tensile extrusion experiment (u)

Eulerian hydrocode simulations utilizing the Mechanical Threshold Stress flow stress model were performed to provide insight into a dynamic extrusion experiment. The dynamic extrusion response of copper (three different grain sizes) and tantalum spheres were simulated with MESA, an explicit, 2-D Eulerian continuum mechanics hydrocode and compared with experimental data. The experimental data consisted of high-speed images of the extrusion process, recovered extruded samples, and post test metallography. The hydrocode was developed to predict large-strain and high-strain-rate loading problems. Some of the features of the features of MESA include a high-order advection algorithm, a material interface tracking scheme and a van Leer monotonic advection-limiting. The Mechanical Threshold Stress (MTS) model was utilized to evolve the flow stress as a function of strain, strain rate and temperature for copper and tantalum. Plastic strains exceeding 300% were predicted in the extrusion of copper at 400 m/s, while plastic strains exceeding 800% were predicted for Ta. Quantitative comparisons between the predicted and measured deformation topologies and extrusion rate were made. Additionally, predictions of the texture evolution (based upon the deformation rate history and the rigid body rotations experienced by the copper during the extrusion process) were compared with the orientation imaging microscopy measurements. Finally, comparisons between the calculated and measured influence of the initial texture on the dynamic extrusion response of tantalum was performed.

36 MATERIALS SCIENCE↗

Formation of titanium carbonitride film by laser treatment: Structural and transport properties

In-plane and Out-of-plane Grazing incidence X-ray diffraction is used to characterize the preferred orientation present in the titanium carbonitride films using ADXRD beamline at INDUS 2 synchrotron radiation source. GIXRD shows the formation of mixture of FCCTiC{sub x}N{sub (1-x)} films for different values of x along with the solid solution. From the in-plane and out-of-plane XRD measurements, we have observed that a specific texture along the c-axis of Ti has been formed during the laser treatment process. Due to the diffusion of C and N into Ti, the resistance of the specimen has been decreases with respect to the resistance of pure Ti sheet. The formed phases are stable and there is no structural relaxation has been observed during annealing process.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Boundary characterization using 3D mapping of geometrically necessary dislocations in AM Ta microstructure

Additive manufacturing (AM) of high strength metallic materials produces microstructures and defects that deviate substantially from those created through conventional manufacturing methods. It has recently been demonstrated that with application of extreme energy densities, a high-temperature refractory metal, tantalum (Ta), can be printed to a fully dense state with exceptionally low porosity. Here we employ a combination of three-dimensional electron backscattered diffraction (EBSD) TriBeam technology and crystallographic geometrically necessary dislocation (GND) theory to characterize the microstructure and defect boundaries of this unusual AM product. Two-dimensional (2D) EBSD and these three-dimensional (3D) measurements indicate that the microstructure of AM Ta is highly oriented <111> along the build direction, yet at the same time contains large crystallographic orientation gradients that span mm’s across the build. Crystallographic GND density analysis of the 3D microstructure reveals that highly misoriented subboundaries exist within this strongly textured microstructure that have large dislocation densities of 1×10 16 m –2 , just as large as those comprising the high-angle grain boundaries (HAGBs) in the same material. The 3D crystallographic GND density mapping reveals these subboundaries are part of a complex, finely spaced network that extends throughout the entire microstructure. Here, the orientation of these boundaries can be related to the scan strategy used during printing. TEM measurements corroborate an extremely high dislocation density at the microscale and indicate a cell-like dislocation network structure existing in the AM Ta at the sub-μm scale.

36 MATERIALS SCIENCE↗

Controlled nanostructuration of polycrystalline tungsten thin films

Nanostructured tungsten thin films have been obtained by ion beam sputtering technique stopping periodically the growing. The total thickness was maintained constant while nanostructure control was obtained using different stopping periods in order to induce film stratification. The effect of tungsten sublayers' thicknesses on film composition, residual stresses, and crystalline texture evolution has been established. Our study reveals that tungsten crystallizes in both stable {alpha}- and metastable {beta}-phases and that volume proportions evolve with deposited sublayers' thicknesses. {alpha}-W phase shows original fiber texture development with two major preferential crystallographic orientations, namely, {alpha}-W<110> and unexpectedly {alpha}-W<111> texture components. The partial pressure of oxygen and presence of carbon have been identified as critical parameters for the growth of metastable {beta}-W phase. Moreover, the texture development of {alpha}-W phase with two texture components is shown to be the result of a competition between crystallographic planes energy minimization and crystallographic orientation channeling effect maximization. Controlled grain size can be achieved for the {alpha}-W phase structure over 3 nm stratification step. Below, the {beta}-W phase structure becomes predominant.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structure and magnetic properties of low-temperature phase Mn-Bi nanosheets with ultra-high coercivity and significant anisotropy

The microstructure, crystal structure, and magnetic properties of low-temperature phase (LTP) Mn-Bi nanosheets, prepared by surfactant assistant high-energy ball milling (SA-HEBM) with oleylamine and oleic acid as the surfactant, were examined with scanning electron microscopy, X-ray diffraction, and vibrating sample magnetometer, respectively. Effect of ball-milling time on the coercivity of LTP Mn-Bi nanosheets was systematically investigated. Results show that the high energy ball milling time from tens of minutes to several hours results in the coercivity increase of Mn-Bi powders and peak values of 14.3 kOe around 10 h. LTP Mn-Bi nanosheets are characterized by an average thickness of tens of nanometers, an average diameter of ∼1.5 μm, and possess a relatively large aspect ratio, an ultra-high room temperature coercivity of 22.3 kOe, a significant geometrical and magnetic anisotropy, and a strong (00l) crystal texture. Magnetization and demagnetization behaviors reveal that wall pinning is the dominant coercivity mechanism in these LTP Mn-Bi nanosheets. The ultrafine grain refinement introduced by the SA-HEBM process contribute to the ultra-high coercivity of LTP Mn-Bi nanosheets and a large number of defects put a powerful pinning effect on the magnetic domain movement, simultaneously. Further magnetic measurement at 437 K shows that a high coercivity of 17.8 kOe and a strong positive temperature coefficient of coercivity existed in the bonded permanent magnet made by LTP Mn-Bi nanosheets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ti-Nb thin films deposited by magnetron sputtering on stainless steel

Thin films of Ti-Nb alloys were deposited on AISI 316L stainless steel substrate by magnetron sputtering, and the structure, composition, morphology, and microstructure of the films were analyzed by means of x-ray diffraction (XRD), (scanning) transmission electron microscopy (TEM) coupled with energy-dispersive x-ray spectroscopy, atomic force microscopy (AFM), and x-ray photoelectron spectroscopy (XPS). Thin films of four compositions were produced: Ti{sub 85}Nb{sub 15} (Ti-26 wt. % Nb), Ti{sub 80}Nb{sub 20} (Ti-33 wt. % Nb), Ti{sub 70}Nb{sub 30} (Ti-45 wt. % Nb), and Ti{sub 60}Nb{sub 40} (Ti-56 wt. % Nb). Structural characterization by XRD indicated that only the β phase was present in the thin films and that the increase in the Nb content modified the alloy film texture. These changes in the film texture, also detected by TEM analysis, were attributed to different growth modes related to the Nb content in the alloy films. The mean grain sizes measured by AFM increased with the Nb amount (from 197 to 222 nm). XPS analysis showed a predominance of oxidized Ti and Nb on the film surfaces and an enrichment of Ti.

36 MATERIALS SCIENCE↗

A transient heating event in the history of a highlands troctolite from Apollo 12 soil 12033

A 2-mm particle, consisting of a troctolite clast attached to a small amount of glassy soil breccia, was found in a thin section of grains from Apollo 12 sample 12033,66. A description is given of the evolutionary history of the troctolite, taking into account the unique texture. It appears that the particle was broken from its parent rock and projected to Oceanus Procellarum from a source area in the highlands. Before, during, or after the flight, the troctolite was welded to a soil breccia by a minor amount of melting along the contact. It is argued that two separate heating events may be involved. The hypothesis is considered that the partial remelting and quenching of the troctolite took place very rapidly. Attention is given to melting experiments which test and confirm this hypothesis.

Marvin, U. B.↗

Petrology of some lithic fragments from Luna 20.

Microscopic and electron microprobe studies were made of polished thin sections of part of a 30-mg sample of 250- to 500-micron lunar soil returned by Luna 20 from a point between Mare Fecunditatis and Mare Crisium. Very fine-grained lithic (crystalline) rock fragments, composing about one-fifth of the total sample, have mineralogical compositions equivalent to various types of gabbro, anorthositic gabbro, gabbroic anorthosite, and troctolite, with minor basalt. The textures now observed in these fragments are in large part metamorphic. Twenty-seven electron microprobe analyses of minerals from these fragments are presented, including olivine, plagioclase, pyroxene, spinel, nickel-iron, and a Zr-Ti-REE mineral possibly similar to 'phase B' of Lovering and Wark (1971). Analyses of seven melt inclusions and 28 defocused beam analyses of lithic fragments are also given. Some of the fragments contain 'gas' inclusions which, along with the fine grain size, are believed to indicate final crystallization under low pressure near surface conditions.

Roedder, E.↗

Effect of carbon content on solidification behaviors and morphological characteristics of the constituent phases in Cr-Fe-C alloys

A combination of transmission electron microscopy, electron backscatter diffraction and wavelength dispersive spectrum has been used to identify crystal structure, grain boundary characteristic and chemical composition of the constituent phases in Cr-Fe-C alloys with three different carbon concentrations. Depending on the three different carbon concentrations, the solidification structures are found to consist of primary {alpha}-phase and [{alpha} + (Cr,Fe){sub 23} C{sub 6}] eutectic in Cr-18.4Fe-2.3 C alloy; primary (Cr,Fe){sub 23} C{sub 6} and [{alpha} + (Cr,Fe){sub 23} C{sub 6}] eutectic in Cr-24.5Fe-3.8 C alloy and primary (Cr,Fe){sub 7} C{sub 3} and [{alpha} + (Cr,Fe){sub 7} C{sub 3}] eutectic in Cr-21.1Fe-5.9 C alloy, respectively. The grain boundary analysis is useful to understand growth mechanism of the primary phase. The morphologies of primary (Cr,Fe){sub 23} C{sub 6} and (Cr,Fe){sub 7} C{sub 3} carbides are faceted structures with polygonal shapes, different from primary {alpha}-phase with dendritic shape. The primary (Cr,Fe){sub 23} C{sub 6} and (Cr,Fe){sub 7} C{sub 3} carbides with strong texture exist a single crystal structure and contain a slight low angle boundary, resulting in the polygonal growth mechanism. Nevertheless, the primary {alpha}-phase with relative random orientation exhibits a polycrystalline structure and comprises a massive high-angle boundary, caused by the dendritic growth mechanism. - Highlights: Black-Right-Pointing-Pointer Microstructures of the as-clad Cr-based alloys are characterized by TEM. Black-Right-Pointing-Pointer EBSD technique has been use to characterize the grain boundary of primary phases. Black-Right-Pointing-Pointer We examine transitions in morphology about the primary phases. Black-Right-Pointing-Pointer Morphologies of primary carbides are polygonal different from primary {alpha}-phase. Black-Right-Pointing-Pointer Solidification structures rely on C concentrations in Cr-Fe-C alloy.

36 MATERIALS SCIENCE↗

Anisotropy of the Thermal Expansion of a Polycrystalline Ni–Mn–Ga Alloy Subjected to Plastic Deformation by Forging

The formation of a sharp crystallographic texture in a Ni–Mn–Ga Heusler alloy by the multiple isothermal forging has been studied. An analysis of the thermal expansion near the martensitic transformation temperatures in the as-cast and forged states of the alloy shows that the thermomechanical treatment leads to an increase in the anisotropy of the sample geometric size changing during the phase transformation, which favors an increase in the functional characteristics of the alloy. The structural studies show that the alloy structure after multiple isothermal forging has the bimodal distribution of grain sizes. The formation of the bimodal structure by forging is assumed to make it possible to enhance the stability of the functional properties of the alloy during repeated cycles of the phase transformation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructure characterization of LAE442 magnesium alloy processed by extrusion and ECAP

The magnesium alloy LAE442 was processed by extrusion and equal channel angular pressing (ECAP) to achieve ultrafine grained microstructure. Detailed characterization of the microstructure was performed by scanning electron microscope, electron back scattered diffraction (EBSD) and transmission electron microscope. The initial, as-cast, microstructure consisted of large grains of ~ 1 mm. The grain refinement due to the processing by severe plastic deformation led to a decrease of the average grain size to ~ 1.7 μm after the final step of ECAP. A detailed characterization of secondary phases showed the precipitation of Al{sub 11}RE{sub 3}, Al{sub 2}Ca and Al{sub 10}RE{sub 2}Mn{sub 7} intermetallic phases. X-ray diffraction measurements proved that Li is dissolved within the magnesium matrix in the as-cast condition. Newly formed Al{sub 3}Li phase was observed after ECAP. The texture formation due to the extrusion and ECAP was different from that in the other magnesium alloys due to the activation of non-basal slip systems as a result of the decrease of the c/a ratio. - Highlights: • Combined extrusion and equal channel angular pressing results in significant grain refinement by factor 1000 approximately. • Al{sub 11}RE{sub 3}, Al{sub 2}Ca and Al{sub 10}RE{sub 2}Mn{sub 7} secondary phases are present in the as-cast material while Li was dissolved in the Mg matrix. • Extrusion and ECAP have no effect on the composition of the secondary phases but they influence strongly their distribution. • Texture evolution is affected by decrease of c/a ratio due to the presence of Li and resulting activation of non-basal slip.

36 MATERIALS SCIENCE↗

Microstructure and Texture Evolutions in AISI 1050 Steel by Flow Forming

Hot rolled and annealed AISI 1050 steel cylindrical coupons were flow formed at different levels of deformation (66% and 90% wall thickness reduction). TEM studies revealed development of ultra fine (sub) grain cell structure due to severe plastic deformation. The transverse subgrain size changed from 10 m (beginning) to 300nm (66% deformation) to 40nm (90% deformation). EBSD study revealed decreased recrystallization fraction at 90% deformation compared with 66% deformation due to orientation pinning from preferred orientation along {002} planes. No evidence of dislocation pinning or cracking was observed on any samples. The aim of the present work is to study the deformation behaviour and microstructural evolution during conventional flow forming process. The study also sheds light on the strengthening behaviour and structural changes during severe straining.

Dynamic Recrystallization↗

Effects of Changing Hot Rolling Direction on Microstructure, Texture and Mechanical Properties of Cu-2.7Be Sheets

A hot rolling scheme (cross-rolling and unidirectional rolling) was adopted to process Cu-2.7Be sheets used as multiplier dynodes in photomultiplier. The effects of changing rolling direction on microstructure, texture and mechanical properties were studied by a combination of XRD, EBSD and TEM. It was found that higher copper-type texture and lower brass texture intensity were obtained in the ultimately cross-rolling (CR) sheet compared with the unidirectional rolling (UR) sheet.The EBSD results indicated that the grain orientation from mainly 〈101〉 for UR sample turns to random for CR sample. Great enhancements in YS and UTS after unidirectional rolling were attributed to the massive and polygonal γ precipitates. The CR sample exhibited lower anisotropy, because of the increase of S and γ precipitates with spherical and tiny shape.

36 MATERIALS SCIENCE↗

AA2024/SiC metal matrix composites simultaneously improve ductility and cracking resistance during elevated temperature deformation

Here this study uses the stir-casting technique to combine a semi-solid AA2024 alloy directly with finely-sized β-SiC p embedded as a powder or with mechanically alloyed granules as a delivery agent. Liquid-state primary fabrication tends to form agglomerates of reinforcement particles, whereas rolling better distributes the composite constituents. Sub-micron reinforcements of low volume fractions do not significantly increase the hardness of the composite materials. Uniaxial tensile testing at elevated temperatures over a wide range of strain rates showed simultaneous increases in the ductility and crack resistance of AA2024 + SiC p granules embedded as a powder when compared to the non-reinforced control material at lower strain rates, with the same toughness as the control material. The maximum engineering strain of 252.7 ± 19.2% was observed in AA2024/SiCp at a strain rate of 10 -4 s -1 . This improvement in properties is attributed to grain refinement in the MMCs, leading to pinning events during the straining and ductility increases. The resultant impediments to grain growth and crack propagation allow the fine-sized reinforcements to control dynamic microstructural changes during fatigue. Cube {001}<100> is a dominant texture component in AA2024, whereas the Goss {011}<100> and S {123}<634> components mainly represent the texture of the discontinuously reinforced aluminum matrix.

36 MATERIALS SCIENCE↗

Magnetic properties and microstructure of bulk Nd-Fe-B magnets solidified in magnetic field

The Nd-Fe-B bulk magnets with a slab shape of 0.9 x 4 x 15 mm{sup 3} were prepared by injection casting into a copper mold. The effects of applying a magnetic field during the casting process on the magnetic properties and microstructure of Nd{sub 9.5}Fe{sub 71.5}Ti{sub 2.5}Zr{sub 0.5}Cr{sub 1}B{sub 14.5}C{sub 0.5} alloy have been studied. The results show that the sample cast with magnetic field has a stronger (00L) texture of Nd{sub 2}Fe{sub 14}B phase with the c-axis perpendicular to the slab plane than the sample cast without magnetic field. The intensity of the texture weakens from surface to inner region of the bulk magnets. Applying a magnetic field during the casting process is helpful to refine the grain size effectively. As a result, the magnetic properties are improved from B{sub r} = 5.8 kG, {sub i}H{sub c} = 6.5 kOe, and (BH){sub max} = 5.9 MGOe for thesample cast without magnetic field to B{sub r} = 6.1 kG, {sub i}H{sub c} = 10.3 kOe, and (BH){sub max} = 7.3 MGOe for the sample cast with a 3.7 kOe magnetic field.

36 MATERIALS SCIENCE↗