Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flight”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

In-flight load testing of advanced shuttle thermal protection systems

NASA Ames Research Center has conducted in-flight airload testing of some advanced thermal protection systems (TPS) at the Dryden Flight Research Center. The two flexible TPS materials tested, felt reusable surface insulation (FRSI) and advanced flexible reusable surface insulation (AFRSI), are currently certified for use on the Shuttle orbiter. The objectives of the flight tests were to evaluate the performance of FRSI and AFRSI at simulated launch airloads and to provide a data base for future advanced TPS flight tests. Five TPS configurations were evaluated in a flow field which was representative of relatively flat areas without secondary flows. The TPS materials were placed on a fin, the Flight Test fixture (FTF), that is attached to the underside of the fuselage of an F-104 aircraft. This paper describes the test approach and techniques used and presents the results of the advanced TPS flight test. There were no failures noted during post-flight inspections of the TPS materials which were exposed to airloads 40 percent higher than the design launch airloads.

Trujillo, B. M.↗
NASA NTRS1982

KC-135 wing and winglet flight pressure distributions, loads, and wing deflection results with some wind tunnel comparisons

A full-scale winglet flight test on a KC-135 airplane with an upper winglet was conducted. Data were taken at Mach numbers from 0.70 to 0.82 at altitudes from 34,000 feet to 39,000 feet at stabilized flight conditions for wing/winglet configurations of basic wing tip, 15/-4 deg, 15/-2 deg, and 0/-4 deg winglet cant/incidence. An analysis of selected pressure distribution and data showed that with the basic wing tip, the flight and wind tunnel wing pressure distribution data showed good agreement. With winglets installed, the effects on the wing pressure distribution were mainly near the tip. Also, the flight and wind tunnel winglet pressure distributions had some significant differences primarily due to the oilcanning in flight. However, in general, the agreement was good. For the winglet cant and incidence configuration presented, the incidence had the largest effect on the winglet pressure distributions. The incremental flight wing deflection data showed that the semispan wind tunnel model did a reasonable job of simulating the aeroelastic effects at the wing tip. The flight loads data showed good agreement with predictions at the design point and also substantiated the predicted structural penalty (load increase) of the 15 deg cant/-2 deg incidence winglet configuration.

Montoya, L. C.↗
NASA NTRS1984

Development and Evaluation of a Performance Modeling Flight Test Approach Based on Quasi Steady-State Maneuvers

The development, implementation and flight test evaluation of a performance modeling technique which required a limited amount of quasisteady state flight test data to predict the overall one g performance characteristics of an aircraft. The concept definition phase of the program include development of: (1) the relationship for defining aerodynamic characteristics from quasi steady state maneuvers; (2) a simplified in flight thrust and airflow prediction technique; (3) a flight test maneuvering sequence which efficiently provided definition of baseline aerodynamic and engine characteristics including power effects on lift and drag; and (4) the algorithms necessary for cruise and flight trajectory predictions. Implementation of the concept include design of the overall flight test data flow, definition of instrumentation system and ground test requirements, development and verification of all applicable software and consolidation of the overall requirements in a flight test plan.

Yechout, T. R.↗
NASA NTRS1984

A flight-test and simulation evaluation of the longitudinal final approach and landing performance of an automatic system for a light wing loading STOL aircraft equipped with wing spoilers

As part of a comprehensive flight-test investigation of short takeoff and landing (STOL) operating systems for the terminal systems for the terminal area, an automatic landing system has been developed and evaluated for a light wing-loading turboprop-powered aircraft. An advanced digital avionics system performed display, navigation, guidance, and control functions for the test aircraft. Control signals were generated in order to command powered actuators for all conventional controls and for a set of symmetrically driven wing spoilers. This report describes effects of the spoiler control on longitudinal autoland (automatic landing) performance. Flight-test results, with and without spoiler control, are presented and compared with available (basically, conventional takeoff and landing) performance criteria. These comparisons are augmented by results from a comprehensive simulation of the controlled aircraft that included representations of the microwave landing system navigation errors that were encountered in flight as well as expected variations in atmospheric turbulence and wind shear. Flight-test results show that the addition of spoiler control improves the touchdown performance of the automatic landing system. Spoilers improve longitudinal touchdown and landing pitch-attitude performance, particularly in tailwind conditions. Furthermore, simulation results indicate that performance would probably be satisfactory for a wider range of atmospheric disturbances than those encountered in flight. Flight results also indicate that the addition of spoiler control during the final approach does not result in any measurable change in glidepath track performance, and results in a very small deterioration in airspeed tracking. This difference contrasts with simulations results, which indicate some improvement in glidepath tracking and no appreciable change in airspeed tracking. The modeling problem in the simulation that contributed to this discrepancy with flight was not resolved.

Brown, S. C.↗
NASA NTRS1983

In-flight load testing of advanced thermal protection systems

NASA Ames Research Center has conducted in-flight airload testing of some advanced thermal protection systems (TPS) at the Dryden Flight Research Center. The two flexible TPS materials tested, felt reusable surface insulation (FRSI) and advanced flexible reusable surface insulation (AFRSI), are currently certified for use on the Shuttle orbiter. The objectives of the flight tests were to evaluate the performance of FRSI and AFRSI at simulated launch airloads and to provide a data base for future advanced TPS flight tests. Five TPS configurations were evaluated in a flow field which was representative of relatively flat areas without secondary flows. The TPS materials were placed on a fin, the Flight Test Fixture (FTF), that is attached to the underside of the fuselage of an F-104 aircraft. This paper describes the test approach and techniques used and presents the results of the advanced TPS flight test. There were no failures noted during post-flight inspections of the TPS materials which were exposed to airloads 40 percent higher than the design launch airloads.

Trujillo, B. M.↗
NASA NTRS1983

AFTI/F-16 flight test results and lessons

The AFTI/F-16 flight test program is summarized, and several design issues of general interest are addressed. A brief description is given of the test vehicle, its flight control modes, and the flight envelopes in which testing was performed. Flight test results are summarized by addressing benefits experienced in flight control task-tailoring, handling qualities in mission tasks, aircraft structure considerations, digital flight control system performance, and human factors. Finally, several design issues relevant to future fighter aircraft are examined, including degraded flight control, system complexity, simplex information in redundant systems, and single failure propagation in redundant systems.

Ishmael, S. D.↗
NASA NTRS1985

Determination of rarefied-flow aerodynamics of the Shuttle orbiter from flight measurements on STS-6 and STS-7

This report presents the flight data results from the High Resolution Accelerometer Package (HiRAP) experimment on the sixth and seventh Shuttle missions (i.e. STS-6 and STS-7). The data have been reduced to produce aerodynamic force coefficients, principally L/D in the rarefied flow regime. Also, a technique is used to extract approximate body-axis aerodynamic coefficients from the flight data. Comparisons of the rarefied transition flow aerodynamic behavior between the two sets of flight data indicate differences, primarily in the free-molecule flow coefficients; i.e. STS-7 shows a free-molecule flow behavior which correlates with diffuse surface reflection conditions, while STS-6 does not. The data have also been used to estimate the density profiles in the atmosphere. The atmospheric density is generated from 60 to 160 km from each flight. The density profiles produced have a primary wave structure and differences are observed between the two sets of flight data. A new rarefied transitional flow aerodynamic bridging formula has been generated from the flight data. Comparisons with the flight bridging formula and existing Monte Carlo and wind-tunnel data are made.

Blanchard, R. C.↗
NASA NTRS1984

Flight versus simulator scan behavior

It is pointed out that most of the modern flight simulators used for pilot training have included expensive motion bases, while the quantitative justification for motion is lacking. The present investigation is concerned with the effects of flight versus simulator conditions on scan behavior as a function of control mode and the presence or absence of traffic on the map display. Matching tests conducted in flight and in a fixed-base simulator permitted an evaluation of the differences in scanning behavior in the real world (flight) and in the 'less real' world (simulator). Scanning behavior in flight was found to be significantly different from the simulator. In flight, the dwell percentage increased on the Electronic Attitude Direction Indicator (EADI), and decreased on the Electronic Horizontal Situation Indicator (EHSI). The average dwell time on all instruments decreased in flight.

Spady, A. A., Jr.↗
NASA NTRS1984

Writing executable assertions to test flight software

An executable assertion is a logical statement about the variables or a block of code. If there is no error during execution, the assertion statement results in a true value. Executable assertions can be used for dynamic testing of software. They can be employed for validation during the design phase, and exception and error detection during the operation phase. The present investigation is concerned with the problem of writing executable assertions, taking into account the use of assertions for testing flight software. They can be employed for validation during the design phase, and for exception handling and error detection during the operation phase The digital flight control system and the flight control software are discussed. The considered system provides autopilot and flight director modes of operation for automatic and manual control of the aircraft during all phases of flight. Attention is given to techniques for writing and using assertions to test flight software, an experimental setup to test flight software, and language features to support efficient use of assertions.

Mahmood, A.↗
NASA NTRS1985

An expert planner for the dynamic flight environment

This paper presents a robust robot planner that functions in the complex and dynamic flight domain. The robot pilot flies an aircraft between two airports and can adjust in flight to changes in the environment such as closed destination airport, thunderstorm in the flight path, and failed engine. The planner adjusts to the world changes by locally patching around the break point instead of complete replanning. The planning architecture is based on the vertical decomposition of domain knowledge, resulting in shallow planning and recovery planning. This robot flight planner can be utilized as the front end of an intelligent flight monitor. The flight planner dynamically generates the references that are used to determine whether the flight crew should be notified of potential problems. The implementation of this robot planner is also discussed.

Chen, D. C.↗
NASA NTRS1988

Current flight test experience related to structural divergence of forward-swept wings

Flight testing the X-29A forward-swept wing aircraft has required development of new flight test techniques to accomplish subcritical extrapolations to the actual structural divergence dynamic pressure of the aircraft. This paper provides current experience related to applying these techniques to analysis of flight data from the forward-swept wing in order to assess the applicability of these techniques to flight test data. The measurements required, maneuvers flown, and flight test conditions are described. Supporting analytical predictions for the techniques are described and the results using flight data are compared to these predictions. Use of the results during envelope expansion and the resulting modifications to the techniques are discussed. Some of the analysis challenges that occurred are addressed and some preliminary conclusions and recommendations are made relative to the usefulness of these techniques in the flight test environment.

Schuster, Lawrence S.↗
NASA NTRS1987

Electro-optical flight deflection measurement system

This paper describes an electrooptical flight-deflection measurement system (FDMS) developed for use on highly-maneuverable-aircraft-technology (HiMAT) RPV flight research program. The FDMS provides in-flight measurements of the aircraft structural deflections and magnetic-tape recordings for automated data processing. The capabilities and limitations, requirements for installation on an aircraft, analytical considerations, and typical flight data acquired from the HiMAT research program are examined. The flight data indicate that the background light is the major obstacle to acquiring high-quality data and that the relationship between the target displacement and the output of the FDMS is nonlinear; however, the nonlinear effects can be minimized with judicious planning of the installation of the FDMS on the aircraft. Excellent flight deflection data were obtained from both the HiMAT and X-29 A flight research program with very little data lost as a result of encounters with severe background light.

Deangelis, V. Michael↗
NASA NTRS1988

Flight projects overview

Information is given in viewgraph form on the activities of the Flight Projects Division of NASA's Office of Aeronautics and Space Technology. Information is given on space research and technology strategy, current space flight experiments, the Long Duration Exposure Facility, the Orbiter Experiment Program, the Lidar In-Space Technology Experiment, the Ion Auxiliary Propulsion System, the Arcjet Flight Experiment, the Telerobotic Intelligent Interface Flight Experiment, the Cryogenic Fluid Management Flight Experiment, the Industry/University In-Space Flight Experiments, and the Aeroassist Flight Experiment.

Levine, Jack↗
NASA NTRS1989

Determination of longitudinal aerodynamic derivatives using flight data from an icing research aircraft

A flight test was performed with the NASA Lewis Research Center's DH-6 icing research aircraft. The purpose was to employ a flight test procedure and data analysis method, to determine the accuracy with which the effects of ice on aircraft stability and control could be measured. For simplicity, flight testing was restricted to the short period longitudinal mode. Two flights were flown in a clean (baseline) configuration, and two flights were flown with simulated horizontal tail ice. Forty-five repeat doublet maneuvers were performed in each of four test configurations, at a given trim speed, to determine the ensemble variation of the estimated stability and control derivatives. Additional maneuvers were also performed in each configuration, to determine the variation in the longitudinal derivative estimates over a wide range of trim speeds. Stability and control derivatives were estimated by a Modified Stepwise Regression (MSR) technique. A measure of the confidence in the derivative estimates was obtained by comparing the standard error for the ensemble of repeat maneuvers, to the average of the estimated standard errors predicted by the MSR program. A multiplicative relationship was determined between the ensemble standard error, and the averaged program standard errors. In addition, a 95 percent confidence interval analysis was performed for the elevator effectiveness estimates, C sub m sub delta e. This analysis identified the speed range where changes in C sub m sub delta e could be attributed to icing effects. The magnitude of icing effects on the derivative estimates were strongly dependent on flight speed and aircraft wing flap configuration. With wing flaps up, the estimated derivatives were degraded most at lower speeds corresponding to that configuration. With wing flaps extended to 10 degrees, the estimated derivatives were degraded most at the higher corresponding speeds. The effects of icing on the changes in longitudinal stability and control derivatives were adequately determined by the flight test procedure and the MSR analysis method discussed herein.

Ranaudo, R. J.↗
NASA NTRS1989

Prediction of forces and moments for flight vehicle control effectors: Workplan

Two research activities directed at hypersonic vehicle configurations are currently underway. The first involves the validation of a number of classical local surface inclination methods commonly employed in preliminary design studies of hypersonic flight vehicles. Unlike studies aimed at validating such methods for predicting overall vehicle aerodynamics, this effort emphasizes validating the prediction of forces and moments for flight control studies. Specifically, several vehicle configurations for which experimental or flight-test data are available are being examined. By comparing the theoretical predictions with these data, the strengths and weaknesses of the local surface inclination methods can be ascertained and possible improvements suggested. The second research effort, of significance to control during take-off and landing of most proposed hypersonic vehicle configurations, is aimed at determining the change due to ground effect in control effectiveness of highly swept delta planforms. Central to this research is the development of a vortex-lattice computer program which incorporates an unforced trailing vortex sheet and an image ground plane. With this program, the change in pitching moment of the basic vehicle due to ground proximity, and whether or not there is sufficient control power available to trim, can be determined. In addition to the current work, two different research directions are suggested for future study. The first is aimed at developing an interactive computer program to assist the flight controls engineer in determining the forces and moments generated by different types of control effectors that might be used on hypersonic vehicles. The first phase of this work would deal in the subsonic portion of the flight envelope, while later efforts would explore the supersonic/hypersonic flight regimes. The second proposed research direction would explore methods for determining the aerodynamic trim drag of a generic hypersonic flight vehicle and ways in which it can be minimized through vehicle design and trajectory optimization.

Maughmer, Mark D.↗
NASA NTRS1988

Current flight test experience related to structural divergence of forward-swept wings

Flight testing the X-29A forward-swept wing aircraft has required development of new flight test techniques to accomplish subcritical extrapolations to the actual structural divergence dynamic pressure of the aircraft. This paper provides current experience related to applying these techniques to analysis of flight data from the forward-swept wing in order to assess the applicability of these techniques to flight test data. The measurements required, manuevers flown, and flight test conditions are described. Supporting analytical predictions for the techniques are described and the results using flight data are compared to these predictions. Use of the results during envelope expansion and the resulting modifications to the techniques are discussed. Some of the analysis challenges that occurred are addressed and some preliminary conclusions and recommendations are made relative to the usefulness of these techniques in the flight test environment.

Schuster, Lawrence S.↗
NASA NTRS1988

Fifty years of laminar flow flight testing

Laminar flow flight experiments conducted over the past 50 years are reviewed. The emphasis is on flight testing conducted under the NASA Laminar Flow Control Program, which has been directed towards the most challenging technology application, the high-subsonic-speed transport. The F111/TACT NLF Glove Flight Test, the F-14 Variable-Sweep Transition Flight Experiment, the 757 Wing-Noise Survey and NLF Glove Flight Test, the NASA Jetstar Leading-Edge Flight Test Program, and the recently initiated Hybrid Laminar-Flow-Control Flight Experiment are discussed.

Wagner, R. D.↗
NASA NTRS1987

The 757 NLF glove flight test results

A major concern in the application of a laminar flow wing design to commercial transports is whether laminar flow can be sustained in the presence of the noise environment due to wing mounted turbofan engines. To investigate this issue, a flight test program was conducted using the Boeing 757 flight research airplane with a portion of the wing modified to obtain natural laminar flow. The flight test had two primary objectives. The first was to measure the noise levels on the upper and lower surface of the wing for a range of flight conditions. The second was to investigate the effect of engine noise on laminar boundary layer transition. The noise field on the wing and transition location on the glove were then measured as a function of the engine power setting at a given flight condition. The transition and noise measurement on the glove show that there is no apparent effect of engine noise on the upper surface transition location. On the lower surface, the transition location moved forward 2 to 3 percent chord. A boundary layer stability analysis to the flight data showed that cross flow disturbances were the dominant cause of transition at most flight conditions.

Runyan, L. Jim↗