Results for “flat” — Page 56

NASA NTRSDate not supplied

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗

NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗

NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗

NASA NTRSDate not supplied

Film Cooling Effectiveness Measurements on a CMC-Simulated Flat Plate

Ceramic matrix composites (CMC) are high temperature materials that can allow higher operating turbomachinery engine temperatures with less coolant required. One method of fabricating ceramic matrix composites is by weaving fibers into the shape of an airfoil. Generally, CMC fiber tows are assembled with various weave patterns, but this uneven surface could introduce aerodynamic losses, and it will be necessary to determine the best film cooling hole arrangement for minimal thermal engine efficiency loss. As part of an effort to assess the impact of geometric constraints of CMC implementation relative to metallic high pressure turbine blades, an experimental study was performed to investigate the effect of film cooling on a CMC-like surface roughened flat plate. Film cooling effectiveness measurements were acquired on a large-scale surface with a ceramic matrix composite weave pattern and on a smooth surface for comparison. A single row and a 2-row cooling hole arrangement were investigated with different hole sizes. Infrared thermography data was acquired at several Reynolds numbers and blowing ratios. Results showed that the effect on span averaged film cooling effectiveness was small between a weave surface pattern and a smooth surface, while hole spacing dependence had a much stronger effect.

infrared↗

NASA NTRSDate not supplied

A Vacuum-Compatible, Spectrally Tunable, Flat Panel Uniform Source for Testing Large Aperture Earth Observation Systems

Labsphere, Inc in conjunction with NASA GSFC and Genesis Engineering Solutions inc. has developed an innovative, fully T-VAC compatible, calibration spectro-radiometric illumination source with a highly uniform large-area rectangular flat panel active area. This source leverages a new shaped integration geometry to achieve high uniformity over a large active output area while maintaining a smaller and more robust overall form-factor when compared to previous designs or integrating spheres. This new illuminator also leverages a set of selectable LED arrays as well as broadband tungsten-halogen sources to provide multi-level, wide spectrum reference illumination to the VIIRS instrument over all optical sensor bands during pre-launch testing. The first unit has been demonstrated to meet its requirements using ambient technology and a fully-vacuum-compatible second unit is planned to allow testing for T-VAC campaigns. This technology is both flexible and capable of meeting the needs of many other instruments/missions requiring this type of test/calibration capability.

Jeff Holt↗

NASA NTRSDate not supplied

A Vacuum-Compatible, Spectrally Tunable, Flat Panel Uniform Source for Testing Large Aperture Earth Observation Systems

Labsphere, Inc. in conjunction with NASA GSFC and Genesis Engineering Solutions Inc., has developed an innovative, vacuum compatible, calibration spectro-radiometric illumination source with a highly uniform large-area rectangular flat panel active area. This device features a uniquely shaped diffuse integration geometry to achieve high uniformity over a large active output area while maintaining a smaller and more robust overall form-factor when compared to previous designs or integrating spheres. A new liquid-cooled hybrid quartz-tungsten (QT) and light emitting diode (LED) source module has been engineered to provide direct-in-vacuum reference illumination over the full dynamic range and spectrum of the VIIRS instrument’s optical bands during pre-launch testing. The first unit has been demonstrated to meet its requirements using ambient technology and a fully-vacuum-compatible second unit is planned to allow testing in thermal vacuum (TVAC) campaigns. This technology is flexible and capable of meeting the needs of many other instruments/missions requiring this type of test/calibration capability.

Jeffrey Holt↗

NASA NTRS2025

Engineered Edge Effect Stress Redistribution in Suspended Thin Film Stacks for Flatness Control

This paper presents the systematic study of edge effect stresses and interaction between thin film stacks to achieve flat suspended thin film structures. Finite element modeling (FEM) was used for rapid analysis of support structures on microshutter array (MSA) shutter blades. The design application aims to flatten the blades to provide ultra-high contrast to optical detectors using MSAs as field masks. This is the first comprehensive study of microscopic surface feature edge effect and film-to-film stress interaction in micro electromechanical systems (MEMS). This study demonstrates flattening of thin film stacks by stress redistribution by induced shear force at the edge of strategically designed reinforcement structures.

Thin Film MEMS↗

DOE OSTI2025

Combined TDLAS and chemiluminescence imaging in a flat flame burner operated with NH3/H2 blends

Ammonia is a promising hydrogen carrier due to its favorable storage and transport characteristics. However, its direct use in combustion systems is limited by low flammability and potential for high nitrogen oxide emissions. To better understand ammonia combustion, researchers conducted experiments using a flat flame burner and measured species profiles using tunable-diode-laser-absorption-spectroscopy and chemiluminescence imaging. They tested three flame conditions with different ammonia-hydrogen blends and oxygen levels. The results were compared to simulations using various kinetic mechanisms, including one that accounts for excited species chemistry. The goal is to provide direct information about species profiles in a simple system, isolating chemical kinetics from fluid dynamic effects, which can inform the development of more efficient and low-emission combustion systems using ammonia.

ammonia combustion↗

NASA NTRS1947