Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Enhanced flow boiling heat transfer on chromium coated zircaloy-4 using cold spray technique for accident tolerant fuel (ATF) materials

Flow boiling heat transfer tests were conducted to evaluate the Critical Heat Flux (CHF) and Heat Transfer Coefficient (HTC) of conventional and accident tolerant fuel (ATF) cladding materials, i.e., bare Zircaloy-4 (Zr4), and Zircaloy-4 coated with Chromium using physical vapor deposition (PVD) (Zr4-Cr-PVD) and cold spray process (Zr4-Cr-CS), respectively. The tests were performed on a single heater rod with a uniform heat flux profile, at the atmospheric pressure, inlet temperature (24 °C) and mass flow rate (750 kg/m 2 s). HTC’s were increased by 5.2% and 3.3% on Zr4-Cr-CS compared to bare Zr4 and Zr4-Cr-PVD. Improved HTCwas attributed to the increased void fraction and high roughness (Ra = 532 nm) of the Zr4-Cr-CS. In detail, the micro-cavities, which act as bubble seeds, were entirely distributed on the Zr4-Cr-CS, and these micro-cavities generated smaller and faster bubbles, thus the void fraction increased by 10.9% compared to bare Zr4. HTC is improved by these smaller and faster bubbles which can remove heat from the heater rod surface more efficiently. To identify the exact location of CHF, the surface temperature profile was measured using advanced fiber-optic sensors which have high temporal/spatial resolution (distance between point to point: ~2.5 mm, frequency ~100 Hz). CHF occurred at 80–95% along the heated length and showed an 11.6% reduction on Zr4-Cr-CS compared to bare Zr4. We hypothesize the CHF reduction was caused by the lower wettability of the Zr4-Cr-CS which reduces the liquid supply to the surface, and vigorous bubble accumulation owing to high void fraction near the outlet, which results in early formation of the vapor film. During the post-CHF quenching phase, the rougher Zr4-Cr-CS showed larger cooling rates compared to the bare Zr4 and Zr4-Cr-PVD, preventing of oxidation by chromium layer. In conclusion, we demonstrate that the high roughness on the Zr4-Cr-CS increased the number of micro-cavities on the surface, resulting in 5.2% increase in HTC and improvement in the quenching heat transfer performance whereas CHF was 11.6% reduced compared to bare Zr4. Overall statistically there is little effect in the coating with regards to CHF and slight improvement in HTC.

42 ENGINEERING↗
DOE OSTI2022

Application of reference-free natural background–oriented schlieren photography for visualizing leakage sites in building walls

Air leakage in buildings can cause health and comfort concerns for occupants and can contribute to mold growth on building materials, or in extreme conditions, rot of building materials. Unwanted air leakage through the building envelope also contributes to approximately 4 quadrillion Btu (1172 TWh) of energy consumption per year in the building sector in the United States. Locating and sealing leakage sites can improve the energy efficiency, comfort, air quality, and moisture durability of the building stock. Typical methods of finding leakage sites, such as infrared imaging and smoke tracing, rely on concurrent blower door operation, which can also measure the total leakage rate of the building. Smoke tracing can be disruptive to occupants, and infrared imaging and smoke tracing cannot measure the contribution of individual leaks to prioritize sealing efforts. Here, an optical fluid flow imaging technique, reference-free natural background–oriented schlieren imaging, was adapted to visualize air exfiltration. This is the first step in developing a method to noninvasively locate and measure exfiltration or infiltration sites so that sealing efforts can be prioritized. Experimental results of this technique are presented, demonstrating the method's applicability to visualizing exfiltration through three common building claddings in an outdoor environment. Key variables impacting the performance of this technique when applied to building leakage are also discussed.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

A microstructure-based modeling approach to predict the mechanical properties of Zr alloy with hydride precipitates

In nuclear reactors, hydrides can form in fuel cladding due to hydrogen absorption in ZIrcaloy and cause embrittlement. This work presents a microstructure-based finite element model to predict the stress-strain response of Zircaloy containing hydrides. Quantitative microstructural details extracted from scanning electron microscopy (SEM) images were used to generate heterogeneous microstructures including the morphology and spatial distribution of hydrides. The constitutive material model for zircaloy in this study is based on crystal plasticity theory which considers the hexagonal close-packed (HCP) atomic structure of Zircaloy material. The hydrides were modeled as brittle material along with a damage model. Hydride formation inside the zircoloy matrix results in residual stress. This phenomenon is also captured in this model. A parametric study has been conducted to understand the effect of volume fraction, orientation, and lamellae thickness of the hydride phase on the mechanical properties of the overall material.

Kulkarni, Shank S.↗
DOE OSTI2026

Machine learning guided prediction of solute segregation at coherent and semi-coherent metal/oxide interfaces

Investigation of semi-coherent metal/oxide interfaces with misfit dislocations using density functional theory (DFT) is computationally intensive to the point of being prohibitive, as it involves several hundreds to many thousands of atoms. In this study, we examined the solute segregation behavior at the Fe/Y 2 O 3 interface—a model interface for cladding applications in nuclear fission reactors—using a combination of DFT calculations and machine learning (ML) approaches. Both coherent and semi-coherent interfaces were considered. ML models were trained on DFT-calculated segregation energies to identify the key chemical, geometric and strain energy related features that govern solute segregation behavior at coherent Fe/Y 2 O 3 interfaces. Furthermore, it was found that ML models when trained on DFT calculated segregation energy of elements at a coherent interface, comprising of about a hundred-atom supercell, can predict the segregation energy of elements at a semi-coherent Fe/Y 2 O 3 interface (with multiple hundreds of atoms) at a fraction of computational cost (1/35th), with an accuracy comparable to DFT calculations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

A novel fiber-fretting test for tribological characterization of the fiber/matrix interface

Ceramic matrix composites exhibit excellent high temperature properties and are candidate materials for structural applications from jet engines to nuclear fuel cladding. The strength and deformation behavior of these composites are intrinsically tied to the properties of the fiber/matrix interface. This research introduces a novel technique to evaluate the fundamental friction and wear characteristics of these interfaces. A case study on SiC f /PyC/SiC m composites applies in situ fiber fretting to investigate the kinetic friction coefficient and cyclic wear characteristics of the interphase. The experimental methodology is presented in explicit detail to encourage other researchers to explore the capabilities of this technique. Additionally, testing was carried out as a function of fiber roughness, PyC thickness (≈10, 500, 1200 nm), cycle count (10, 100, 1000), and frequency (1, 5, and 10 Hz). The friction coefficient and wear behavior changed with cycle length due to a transition from adhesive to abrasive mechanisms. SEM fractography provided insights to tribological evolution from adhesive sliding to three-body abrasive wear. The structural disorder at the tribo-surface relating to graphitic content and dangling bond density was investigated using Raman spectroscopy. Properties are contextualized with comparison to uniaxial tensile behavior of the parent composite.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Oxidation behavior of Fe-Cr-2Si alloys in high temperature steam

FeCrSi alloys have been proposed as alternatives to FeCrAl alloys for accident-tolerant fuel cladding in light water reactors. Experiments on the oxidation resistance of three Fe-Cr-2Si alloys in high-temperature steam, with 12, 16, and 20 wt. % Cr, show that ≥16 % Cr is sufficient to form a thin, passivating, binary oxide layer. Additionally, at 1200 °C, only Cr 2 O 3 and SiO 2 form on Fe 16 Cr 2 Si and Fe 20 Cr 2 Si, while additional ternary Fe oxides form on Fe 12 Cr 2 Si. Decohesion and spalling of oxide were observed on Fe-Cr-Si alloys exposed to steam at 900 °C and above. Fe 20 Cr 2 Si exhibits the best oxidation resistance of the three in high-temperature steam.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of grain refinement on high temperature steam oxidation of an FeCrAl alloy

FeCrAl alloys are promising candidates to replace Zr alloys as fuel cladding materials in nuclear light-water reactors. Grain refinement has been indicated to improve irradiation resistance. To enhance corrosion resistance as well, the effects of grain refinement on steam corrosion behavior were investigated in this work. Samples of Kanthal D alloy (Fe-21Cr-5Al) with two different grain sizes (coarse-grained and ultrafine-grained) were exposed to steam at 1200 °C for 2 hrs. In conclusion, results indicate improved steam corrosion resistance in ultrafine-grained Kanthal D with formation of a thinner protective Al oxide layer and the presence of a thin underlying Cr oxide layer.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Assessment of BISON capabilities for component-level prediction of tritium transport in fusion and fission applications

Here we assessed the hydrogen migration and redistribution model implemented in the BISON fuel performance code for component-level tritium transport applications in fusion and fission example scenarios. We developed BISON models of an ITER heat exchanger, light water reactor fuel cladding, and a fluoride salt cooled high temperature reactor heat exchanger. Reasonable agreement between reported values in reference studies and BISON predictions demonstrated the ability of the BISON models to predict tritium transport behavior through steel materials. Next, sensitivity and uncertainty analysis was used to understand key parameter sensitivities within the BISON model for evaluation of tritium migration and redistribution. . The sensitivity analysis showed that the diffusivity activation energy was the most important parameter and that the heat of transport was the least important parameter for tritium migration in steels. Overall, the capabilities of the BISON code for component level modeling of tritium transport are promising.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

A Eulerian three-fluid flow framework for the study of fuel dispersal behavior under loss-of-coolant accident conditions

As the nuclear industry explores new fuel designs to accommodate increased burnup, studying fuel behavior during loss-of-coolant accidents is essential for ensuring the safe operation of light-water reactors. Here, this study presents a computational model to simulate the intricate three-phase flow dynamics of fuel dispersal following cladding breach, where solid fuel particles and carrier fission gases interact with the surrounding liquid or gas medium. The model utilizes a Eulerian three-fluid framework to depict the phase interaction within interpenetrating continua, treating fragmented fuel as granular material. Closure relationships for bulk-flow properties of the solid phase and detailed interfacial exchange terms in high-temperature, high-speed gas-solid-liquid flow scenarios are proposed. The model was validated using adiabatic experimental results in the literature, focusing on characterizing fuel dispersal behavior during loss-of-coolant accidents conditions. Settlement characteristics of the solids, quantified by the probability distribution of equivalent particles, closely matched probability density functions reported in experimental studies. Key highlights of this study include the theoretical description of a coupled three-phase flow with phase change, interpretation of the high-pressure boundary conditions and insights into the transient behavior of gas-solid-liquid phase dynamics during a simulated high-speed dispersal event.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Accurate and efficient predictions of keyhole dynamics in laser materials processing using machine learning-aided simulations

The keyhole phenomenon has been widely observed in laser materials processing, including laser welding, remelting, cladding, drilling, and additive manufacturing. Keyhole-induced defects, primarily pores, dramatically affect the performance of final products, impeding the broad use of these laser-based technologies. The formation of these pores is typically associated with the dynamic behavior of the keyhole. So far, the accurate characterization and prediction of keyhole features, particularly keyhole depth, as a function of time, has been a challenging task. In situ characterization of keyhole dynamic behavior using the synchrotron X-ray technique is informative but complicated and expensive. Current simulations are generally hindered by their poor accuracy and generalization abilities in predicting keyhole depths due to the lack of accurate laser absorptance data. In this study, we develop a machine learning-aided simulation method that accurately predicts keyhole dynamics, especially in keyhole depth fluctuations, over a wide range of processing parameters. In two case studies involving titanium and aluminum alloys, we achieve keyhole depth prediction with a mean absolute percentage error of 10 %, surpassing those simulated using the ray-tracing method with an error margin of 30 %, while also reducing computational time. This exceptional fidelity and efficiency empower our model to serve as a cost-effective alternative to synchrotron experiments. Our machine learning-aided simulation method is affordable and readily deployable for a large variety of materials, opening new doors to eliminate or reduce defects for a wide range of laser materials processing techniques.

Computational fluid dynamics↗
DOE OSTI2023

Bridging microscale to macroscale mechanical property measurements of FeCrAl alloys by crystal plasticity modeling

FeCrAl alloys are candidates for accident tolerant fuel cladding of light water reactors. In this work, a microstructure- and temperature-dependent crystal plasticity model is employed to bridge microscale to macroscale mechanical property measurements of FeCrAl alloys. With the visco-plastic self-consistent (VPSC) polycrystal plasticity framework, a mechanism-based single crystal plasticity (MSCP) model adopts the Arrhenius type rate equation to describe the dependence of the critical resolved shear stress for dislocation slips on their temperature-dependent intrinsic frictional resistance and the microstructure-dependent irradiation hardening. The intrinsic frictional resistance associated with {110}<111> and {112}<111> slip systems were measured by in-situ micromechanical testing on unirradiated/irradiated samples at 25-500 °C. The irradiation hardening is estimated by the Bacon-Kocks-Scattergood (BKS) model with density and size of radiation-induced defects measured from microstructural characterization. Several features associated with thermo-mechanical behavior of unirradiated/irradiated polycrystalline FeCrAl alloys are captured. High density of deformation-induced dislocations and radiation-induced defects results in obvious hardening at room temperature, which is weakened at high temperature, and facilitates damage evolution during deformation. Moreover, both high temperature and radiation-induced defects, which facilitate dislocation multiplication, trigger large hardening rate. Finally, the proposed method together with application of accelerator-based ion irradiation technique is a surrogate approach to simulate neutron damage, improving the efficiency associated with evaluation of mechanical properties of FeCrAl alloys exposed to temperature, stress and radiation conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of differently oriented interlayer phases on the radiation damage of Inconel-$\mathrm{Ni}$ multimetallic layered composite

Multimetallic layered composites (MMLCs) have shown an excellent potential for application under extreme environments, e.g., accident-tolerant fuel cladding, because of their low oxidation tendency and high corrosion resistance. Interfacial phases or complexions in nanocrystalline materials accelerate the annihilation of defects and enhance the radiation resistance of materials, making MMLCs with engineered interlayer phases compelling to deploy in extreme conditions. However, implementation of MMLCs in full capacity remained a challenge due to a lack of fundamental understanding of the underlying mechanisms governing the characteristics of the interface between the metallic layers. The precise role of interlayer phases in MMLCs and their interaction with defects, specifically under extreme conditions, is still unexplored. Pursuing atomistic simulations for various Inconel-Ni MMLCs model materials, we revealed accelerated defect mobility in interlayers with larger crystalline misorientation and the inverse relationship between the interface sink strength to the misorientation angle. Furthermore, we found a linear relation between interlayer misorientation angle with the density of radiation-induced defects and radiation enhanced displacements. So, our results indicate that radiation-induced material degradation is accelerated by the higher defect formation tendency of MMLCs with a high-angle interlayer interface.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Enhanced backscatter and unsaturated blue wavelength shifts in F-doped fused silica optical fibers exposed to extreme neutron radiation damage

Amorphous fused silica (a-SiO 2 ) optical fibers, with and without inscribed Bragg gratings, were interrogated using infrared (~1550 nm) optical backscatter reflectometry during ~25 days of intense neutron irradiation to a fast (energy > 0.1 MeV) neutron fluence of ~10 21 n/cm 2 , or ~1.5 atomic displacements per atom. The reflected light amplitudes in Ge-doped core telecommunications fiber dropped below detection limits (>15 dB attenuation) within 3 days of irradiation (~10 20 fast n/cm 2 ). Here, amplitudes from a pure silica core, F-doped silica cladding fiber reached equilibrium levels ~1.5–2 dB higher than pre-irradiation values, whereas Bragg gratings inscribed in the same fiber using a femtosecond laser (point-by-point method) suffered > 45 dB attenuation. Blue wavelength shifts were initially consistent with previous radiation-induced compaction models but increased linearly with increasing neutron fluence (no evidence of saturation) beyond 10 20 n/cm 2 and exceeded 0.6%, which corresponds to >1,000 °C drift if used to measure temperature changes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High temperature steam oxidation dynamics of U 3 Si 2 with alloying additions: Al, Cr, and Y

Uranium silicides are considered for advanced technology reactor fuels due to their enhanced thermal conductivity and high uranium density (U 3 Si and U 3 Si 2 ) compared to traditional UO 2 . Susceptibility to oxidation and wash out, in the event of a cladding breech, could limit the potential for deployment of silicides as accident tolerant fuels. Mitigating the water reaction for U 3 Si 2 could enable its use as an accident tolerant, high uranium density fuel or as a composite fuel constituent. Reported here is the impact of alloying additions of Al, Cr and Y on the high temperature, steam oxidation response of U 3 Si 2 . In addition to the thermogravimetric response, as melted microstructures, phase compositions and post oxidation analysis are also presented. Here, the investigation shows steam oxidation dynamics are altered, from non-alloyed U 3 Si 2 , under thermally ramped conditions. However, additional alloy development of these fuel forms is necessary for further consideration as candidate accident tolerant fuels in water-cooled reactor designs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure and diffusion behavior of uranium fuel with minor additives

Fission product lanthanides in metallic fuels are known to cause adverse fuel-cladding chemical interaction (FCCI). Tin (Sn) and palladium (Pd) are being explored as the potential additives to reduce or mitigate lanthanide-induced FCCI by forming stable Sn-Ln and Pd-Ln compounds. The current study is an investigation of the fuel alloys, U–4Sn, U–4Sn-4Ln, U–4Pd, and U–4Pd-4Ln (wt. %), and their diffusion behaviors with Fe. Microstructural analysis was performed using scanning electron microscopy (SEM). Further, the binary phases in the UPd and USn alloys are identified as UPd 3 and suspected U 2 Sn, where U 2 Sn is unknown in the literature. The binary phases in the UPdLn alloy are identified as PdLn and Pd-rich Pd-Ln (Pd 4 Ln 3 and Pd 3 Ln 2 ), and in the USnLn alloy is SnLn. Diffusion of Fe with these binary phases is insignificant compared to the diffusion with U. The Ln-induced FCCI can be mitigated by the additives.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Irradiation performance of nonfertile (Pu-MA-Zr) fast reactor metal fuels

This work was part of a program begun in 2001 to develop advanced nuclear fuels, originally as carriers for plutonium and minor actinides (neptunium, curium, and americium) taken from spent commercial light-water reactors (LWR) so that the plutonium and minor actinides could be ‘burned’ or transmuted in an accelerator or a fast nuclear reactor. A central part of these experiment programs has been the development of advanced fast reactor fuels, because a fast reactor was considered the most efficient vehicle to transmute the actinide waste products, and metallic fuels is a central focus of these tests. An experiment design was developed in which a thermal test reactor, the Advanced Test Reactor (ATR), was used to test small fuel pin prototypes, by creating areas in the core shielded by cadmium filters to produce a largely epithermal and fast neutron spectrum environment in which the pins could be irradiated. The results of non-fertile metallic fuel (no uranium) tests are presented here. Pu-Am-Np-Zr fuels were irradiated to fission densities up to 33 × 10 20 fission/cm 3 and Pu-239 depletions of up to 39%. The depletions were created by roughly 2/3 by fission and 1/3 by transmutation neutron capture. Up to five fuel ‘rodlets’ were irradiated in three sealed capsules stacked axially in the core, and the peak cladding temperatures ranged from 300°C to 500°C, depending on axial location as those near the core centerline are operating hotter and to higher fission densities. Several post-irradiation examinations (precision gamma scanning and fission gas release) were similar to other historical metal fuel experiments in fast reactors. However, optical metallography indicated that two of the rodlets had breached. The exact reasons are unclear. Due to the design of this irradiation experiment a rodlet breach could have increased the temperature in others in the same capsule by contaminating the thermal gap helium with heavier and less conductive fission product gases. Finally, some of those rodlets showed high amounts of fuel/cladding chemical interaction (FCCI).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

(S)TEM/EDS study of native precipitates and irradiation induced Nb-rich platelets in high-burnup M5®

We have investigated microstructure and microchemistry of precipitates and dislocation loops in high-burnup M5® using (scanning) transmission electron microscopy ((S)TEM) equipped with energy dispersive X-ray spectroscopy (EDS). Two (S)TEM lamellae were made by cryo-FIB from the same cladding sample. The Nb-rich native precipitates were found in the metal, in the suboxide and in the oxide. Upon diffraction analysis, most of the Nb-rich native precipitates in the metal matrix remain as β-Nb phase, while no β-Nb native precipitates were found in the oxide. Nearby the oxide and metal (O/M) interface, the native precipitates in the oxide were already oxidized into t-NbO2 phase. At further distance away from the O/M interface, the Nb-rich native precipitates were gradually oxidized and became amorphous. Besides the native precipitates, Nb-rich irradiation induced precipitates (IIPs) were found in the metal matrix. Using g = <0002> vector for imaging, the length of the IIPs was aligned with dislocation loops. However, no Nb segregation to the dislocation loops themselves was observed. For the first time, we report that IIPs indeed exist in the oxide but only within about 1.5 µm away from O/M interface. However, the oxidation state of the IIPs in the oxide is still unclear. The presence of both native precipitates and IIPs in the oxide may indicate the Nb concentration in the oxide solid solution remain low nearby the O/M interface, which may explain the reduced corrosion kinetics of in-pile M5®. On the other hand, no IIPs were observed in the oxide at further distance and this may indicate that they have eventually dissolved back into the oxide. A few mechanisms related to IIPs stability in the oxide are presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗