Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attenuator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Shield materials recommended for space power nuclear reactors

Lithium hydride is recommended for neutron attenuation and depleted uranium is recommended for gamma ray attenuation. For minimum shield weights these materials must be arranged in alternate layers to attenuate the secondary gamma rays efficiently. In the regions of the shield near the reactor, where excessive fissioning occurs in the uranium, a tungsten alloy is used instead. Alloys of uranium such as either the U-0.5Ti or U-8Mo are available to accommodate structural requirements. The zone-cooled casting process is recommended for lithium hydride fabrication. Internal honeycomb reinforcement to control cracks in the lithium hydride is recommended.

Kaszubinski, L. J.↗
NASA NTRS1974

Overvoltage protection network

Electrical equipment to be protected from overvoltage is connected with a possible source of overvoltage via an input conductor. A fuse is connected in series with the input conductor. A spark gap is connected between the input conductor and ground for conducting the overvoltage current to ground and for blowing the fuse to open the circuit to the electrical equipment. A pulse attenuator network is provided between the spark gap and the electrical equipment to be protected for attenuating the pulse of energy passing through the fuse and spark gap prior to blowing of the fuse. The pulse attenuator network includes additional shunt spark gaps, series inductance, and a series connection of a twisted shielded pair of conductors having low-voltage insulation.

Cambra, J. M.↗
NASA NTRS1974

A new device for acquiring ground truth on the absorption of light by turbid waters

The author has identified the following significant results. A new device, called a Spectral Attenuation Board, has been designed and tested, which enables ERTS-1 sea truth collection teams to monitor the attenuation depths of three colors continuously, as the board is being towed behind a boat. The device consists of a 1.2 x 1.2 meter flat board held below the surface of the water at a fixed angle to the surface of the water. A camera mounted above the water takes photographs of the board. The resulting film image is analyzed by a micro-densitometer trace along the descending portion of the board. This yields information on the rate of attenuation of light penetrating the water column and the Secchi depth. Red and green stripes were painted on the white board to approximate band 4 and band 5 of the ERTS MSS so that information on the rate of light absorption by the water column of light in these regions of the visible spectrum could be concurrently measured. It was found that information from a red, green, and white stripe may serve to fingerprint the composition of the water mass. A number of these devices, when automated, could also be distributed over a large region to provide a cheap method of obtaining valuable satellite ground truth data at present time intervals.

Klemas, V.↗
NASA NTRS1974

Spinning mode sound propagation in ducts with acoustic treatment

A detailed theoretical study of the acoustic propagation of spinning modes in acoustically treated open circular ducts is described. The suppressor with splitter rings was modeled by using the rectangular approximation to the annular duct. The theoretical models were used to determine optimum impedance and maximum attenuation for several spinning lobe numbers from 0 to 50. Some interesting results of the analysis are that for circular ducts the maximum possible attenuation and the optimum wall impedance are strong functions of the lobe number. For annular ducts the attenuation and optimum wall impedance are insensitive to the spinning lobe number for well cut-on modes. The above results help explain why suppressors with splitter rings were quite effective in spite of the lack of detailed information on the noise source modal structure.

Rice, E. J.↗
NASA NTRS1973

ATS-F Comsat Millimeter Wave Propagation Experiment

The ATS-F Comsat Millimeter Wave Propagation Experiment has been designed to gather statistical data on the attenuation caused by rain at millimeter wave frequencies. These data will be used to determine system design parameters for future communications satellite systems operating at frequencies above 10 GHz. The experiment has 39 ground terminals transmitting at 13.2 or 17.8 GHz to a transponder on board the ATS-F satellite. The transponder retransmits these signals at 4 GHz to a central earth terminal which records their amplitudes once each second. The data will be analyzed to provide probabilities of attenuation as functions of parameters such as rainfall, location, and time. These probabilities can then be used to determine the required power margins of millimeter wave communications systems. Techniques of overcoming severe attenuation such as site diversity and the use of a spot beam to increase the power level at selected locations will also be evaluated.

Westerlund, L. H.↗
NASA NTRS1974

Nonlinear acoustic propagation in rectangular ducts

The method of multiple scales is used to obtain a second-order uniformly valid expansion for nonlinear acoustic wave propagation in a rectangular duct whose walls are treated with a nonlinear acoustic material. The wave propagation in the duct is characterized by the unsteady nonlinear Euler equations. The results show that nonlinear materials attenuate sound more than linear materials except at high acoustic frequencies. The nonlinear materials produce higher and combination tones which have higher attenuation rates than the fundamentals. Moreover, the attenuation rates of the fundamentals increase with increasing amplitude.

Nayfeh, A. H.↗
NASA NTRS1974

Effect of mean-velocity profile shapes on sound transmission through two-dimensional ducts

Acoustic propagation through a lined two-dimensional duct is examined in order to assess the influence of the shape of the mean-velocity profile on the attenuation rate. Five mean-velocity profiles are considered: linear, parabolic, Pohlhausen, 1/7th power law with a linear sub-layer, and linear with slip at the wall. It is shown that when the attenuation rate is tabulated as a function of the boundary-layer thickness, as is usually done, substantially different results are obtained from the several mean profiles. However, when the displacement thickness is used, a considerable collapse is achieved in the attenuation curves that are obtained from the various profiles. For downstream propagation, all profiles produce essentially the same results over a reasonable range of boundary-layer thickness. However, for many cases of upstream propagation, the results from the 'turbulent' boundary-layer profiles differ significantly from the results of the other profiles even when compared on the basis of displacement thickness.

Hayfeh, A. H.↗
NASA NTRS1974

Non-linear wave propagation in acoustically lined circular ducts

An analysis is presented of the nonlinear effects of the gas motion as well as of the acoustic lining material on the transmission and attenuation of sound in a circular duct with a uniform cross-section and no mean flow. The acoustic material is characterized by an empirical, nonlinear impedance in which the instantaneous resistance is a nonlinear function of both the frequency and the acoustic velocity. The results show that there exist frequency bandwidths around the resonant frequencies in which the nonlinearity decreases the attenuation rate, and outside which the nonlinearity increases the attenuation rate, in qualitative agreement with experimental observations. Moreover, the effect of the gas nonlinearity increases with increasing sound frequency, whereas the effect of the material nonlinearity decreases with increasing sound frequency.

Nayfeh, A. H.↗
NASA NTRS1975

Generalized wave envelope analysis of sound propagation in ducts with stepped noise source profiles and variable axial impedance

A finite difference formulation is presented for sound propagation in a rectangular two-dimensional duct without steady flow. Before the difference equations are formulated, the governing Helmholtz equation is first transformed to a form whose solution tends not to oscillate along the length of the duct. This transformation reduces the required number of grid points by an order of magnitude. Example solutions indicate that stepped noise source profiles have much higher attenuation than plane waves in a uniform impedance liner. Also, multiple stepped impedance liners are shown to have higher attenuation than uniform ducts if the impedances are chosen properly. For optimum noise reduction with axial variations in impedance, the numerical analysis indicates that for a plane wave input the resistance should be near zero at the entrance of a suppressor duct, while the reactance should be near the optimum value associated with the least-attenuated mode in a uniform duct.

Baumeister, K. J.↗
NASA NTRS1975

Effort of spanwise variation of turbulence on the normal acceleration of airplanes with small span relative to turbulence scale

A rigid airplane with an unswept wing is analyzed. The results show that the power spectrum, relative to that for a one-dimensional turbulence field, is significantly attenuated at the higher frequencies even for airplanes with arbitrarily small ratios of span to scale of turbulence. This attenuation is described by a simple weighting function of frequency that depends only on aspect ratio. The weighting function, together with the attenuation due to the unsteady flow of gust penetration, allows the determination of the average rate of zero crossings for airplanes having very small spans without recourse to an integral truncation which is often required in calculations based on a one-dimensional turbulence field.

Pratt, K. G.↗
NASA NTRS1975

An optical radar for airborne use over natural waters

An optical radar for detecting targets in natural waters was built and tested in the Gulf of Mexico. The transmitter consists of a Q switched neodymium glass laser, with output amplified and doubled in KDP to 0.53 micrometer wavelength. The receiver incorporates a noval optical spatial filter to reduce the dynamic range required of the photodetector to a reasonable value. Detection of targets to a depth of 26 meters (84 feet) was achieved with a considerable sensitivity margin. The sensitivity of the radar is highly dependent on the optical attenuation coefficient. In general, measured returns fell between the values predicted on the basis of monopath and multipath attenuation. By means of simple physical arguments, a radar equation for the system was derived. To validate this theoretical model, measurements of optical attenuation and of water surface behavior were also instrumented, and some of these results are given.

Levis, C. A.↗
NASA NTRS1975

Twenty and thirty GHz millimeter wave experiments with the ATS-6 satellite

The ATS-6 millimeter wave experiment, provided the first direct measurements of 20 and 30 GHz earth-space links from an orbiting satellite. Studies at eleven locations in the continental United States were directed at an evaluation of rain attenuation effects, scintillations, depolarization, site diversity, coherence bandwidth, and analog and digital communications techniques. In addition to direct measurements on the 20 and 30 GHz links, methods of attenuation prediction with radars, rain gages, and radiometers were developed and compared with the directly measured attenuation. Initial data results of the ATS-6 millimeter wave experiment from the major participating organizations are presented.

Ippolito, L. J.↗
NASA NTRS1974

Active microwave measurement of soil water content

Measurements of radar backscatter from bare soil at 4.7, 5.9, and 7.1 GHz for incident angles of 0-70 deg have been analyzed to determine sensitivity to soil moisture. Because the effective depth of penetration of the radar signal is only about one skin depth, the observed signals were correlated with the moisture in a skin depth as characterized by the attenuation coefficient (reciprocal of skin depth). Since the attenuation coefficient is a monotonically increasing function of moisture density, it may also be used as a measure of moisture content over the distance involved, which varies with frequency and moisture content. The measurements show an approximately linear increase in scattering with attenuation coefficient of the soil at angles within 10 deg of vertical and all frequencies. At 4.7 GHz this increase continues relatively large out to 70 deg incidence, but by 7.1 GHz the sensitivity is much less even at 20 deg and practically gone at 50 deg.

Ulaby, F. T.↗
NASA NTRS1974

Jet transport noise - A comparison of predicted and measured noise for ILS and two-segment approaches

Centerline noise measured during standard ILS and two-segment approaches in DC-8-61 aircraft were compared with noise predicted for these procedures using an existing noise prediction technique. Measured data is considered to be in good agreement with predicted data. Ninety EPNdB sideline locations were calculated from flight data obtained during two-segment approaches and were compared with predicted 90 EPNdB contours that were computed using three different models for excess ground attenuation and a contour with no correction for ground attenuation. The contour not corrected for ground attenuation was in better agreement with the measured data.

White, K. C.↗
NASA NTRS1976

Twenty and thirty GHz millimeter wave experiments with the ATS-6 satellite

Studies at 11 locations in the continental United States were directed at an evaluation of rain attenuation effects, scintillations, depolarization, site diversity, coherence bandwidth, and analog and digital communications techniques using the Applications Technology Satellite-6(ATS-6). In addition to direct measurements on the 20- and 30-GHz links, methods of attenuation prediction with radars, rain gages, and radiometers were developed and compared with the directly measured attenuation. Initial data results of the ATS-6 millimeter wave experiment were presented. The first section describes the experiment objectives, flight hardware, and modes of operation. The remaining six sections present papers prepared by the major participating organizations in the experiment. The papers present a comprehensive summary of the significant results of the initial 11 months of ATS-6 experiment measurements and related radiometric, radar, and radio-meteorology studies.

Ippolito, L. J.↗
NASA NTRS1976

Analytical and experimental studies of an optimum multisegment phased liner noise suppression concept

Results are presented from detailed analytical studies made to define methods for obtaining improved multisegment lining performance by taking advantage of relative placement of each lining segment. Properly phased liner segments reflect and spatially redistribute the incident acoustic energy and thus provide additional attenuation. A mathematical model was developed for rectangular ducts with uniform mean flow. Segmented acoustic fields were represented by duct eigenfunction expansions, and mode-matching was used to ensure continuity of the total field. Parametric studies were performed to identify attenuation mechanisms and define preliminary liner configurations. An optimization procedure was used to determine optimum liner impedance values for a given total lining length, Mach number, and incident modal distribution. Optimal segmented liners are presented and it is shown that, provided the sound source is well-defined and flow environment is known, conventional infinite duct optimum attenuation rates can be improved. To confirm these results, an experimental program was conducted in a laboratory test facility. The measured data are presented in the form of analytical-experimental correlations. Excellent agreement between theory and experiment verifies and substantiates the analytical prediction techniques. The results indicate that phased liners may be of immediate benefit in the development of improved aircraft exhaust duct noise suppressors.

Sawdy, D. T.↗
NASA NTRS1976

Optimization of suppression for two-element treatment liners for turbomachinery exhaust ducts

Sound wave propagation in a soft-walled rectangular duct with steady uniform flow was investigated at exhaust conditions, incorporating the solution equations for sound wave propagation in a rectangular duct with multiple longitudinal wall treatment segments. Modal analysis was employed to find the solution equations and to study the effectiveness of a uniform and of a two-sectional liner in attenuating sound power in a treated rectangular duct without flow (M = 0) and with uniform flow of Mach 0.3. Two-segment liners were shown to increase the attenuation of sound as compared to a uniform liner. The predicted sound attenuation was compared with measured laboratory results for an optimized two-segment suppressor. Good correlation was obtained between the measured and predicted suppressions when practical variations in the modal content and impedance were taken into account. Two parametric studies were also completed.

Motsinger, R. E.↗
NASA NTRS1976

Effect of simulated forward airspeed on small-scale-model externally blown flap noise

Noise tests were conducted on a small-scale model of an externally blown flap lift augmentation system. The nozzle/wing model was subjected to external flow that simulated takeoff and landing flight velocities by placing it in a 33-centimeter-diameter free jet. The results showed that external flow attenuated the noise associated with the various configurations tested. The amount of attenuation depended on flap setting. More attenuation occurred with a trailing-flap setting of 20 deg than with one of 60 deg. Noise varied with relative velocity as a function of the trailing-flap setting and the angle from the nozzle inlet.

Goodykoontz, J. H.↗