Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “angle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRS1937

Pressure-Distribution Measurements at Large Angles of Pitch on Fins of Different Span-Chord Ratio on a 1/40-Scale Model of the U. S. Airship "Akron."

Report presents the results of pressure-distribution measurements on a 1/40-scale model of the U. S. Airship "Akron" conducted in the NACA 20-foot wind tunnel. The measurements were made on the starboard fin of each of four sets of horizontal tail surfaces, all of approximately the same area but differing in span-chord ratio, for five angles of pitch varying from 11.6 degrees to 34 degrees, for four elevator angles, and at air speeds ranging from 56 to 77 miles per hour. Pressures were also measured at 13 stations along the rear half of the port side of the hull at one elevator setting for the same five angles of pitch and at an air speed of approximately 91 miles per hour. The normal force on the fin and the moment of forces about the fin root were determined. The results indicate that, ignoring the effect on drag, it would be advantageous from structural considerations to use a fin of lower span-chord ratio than that used on the "Akron."

Mchugh, James G↗
NASA NTRS1949

Effect of Afterbody Length and Keel Angle on Minimum Depth of Step for Landing Stability and on Take-Off Stability of a Flying Boat

Tests were made to fill partly the need for information on the effect of afterbody dimensions on the hydrodynamic stability of a flying boat in smooth water. The dimensions investigated were depth of step, angle of afterbody keel, and length of afterbody. An analysis of the data showed that as either the afterbody length or keel angle was increased an accompanying increase in depth of step was required in order to maintain adequate landing stability. The landing-tests results have been reduced to an empirical formula giving the minimum depth of step in terms of afterbody length and keel angle. This formula is compared with results from other tank tests, and the correlation is fairly good. The formula thus becomes of use in preliminary design.

Olson, Roland E↗
NASA NTRS1956

Investigation of the Aerodynamic Characteristics of a Model Wing-Propeller Combination and of the Wing and Propeller Separately at Angles of Attack up to 90 Degrees

This report presents the results of an investigation conducted in the Langley 300 mph 7- by 10-foot wind tunnel for the purpose of determining the aerodynamic characteristics of a model wing-propeller combination, and of the wing and propeller separately at angles of attack up to 90 degrees. The tests covered thrust coefficients corresponding to free-stream velocities from zero forward speed to the normal range of cruising speeds. The results indicate that increasing the thrust coefficient increases the angle of attack for maximum lift and greatly diminishes the usual reduction in lift above the angle of attack for maximum lift.

Kuhn, Richard E↗
NASA NTRS1933

The D.V.L. Gliding-angle Control : W. Hubner Design

This report describes a device for arbitrary enlargement of the gliding angle of airplanes, especially of such with flat gliding angle and difficult landing characteristics. The D.V.L. gliding angle control (design, Hubner) permits a local interruption of the lift distribution along the span and consequently an increased induced drag. The mechanism comprises two wing rudders operated by lever from the pilot's cockpit. Said rudders are fitted on the top side of the wing near the leading edge. The displacement of these rudders results in a separation of the air flow on the top side of the wing.

Hubner, Walter↗
NASA NTRS1994

High-Resolution Optoelectronic Shaft-Angle Encoder

Improved optoelectronic encoder measures absolute angle to which shaft has been rotated. Costs little more than older, less capable encoders do, yet measures absolute angles at high resolution and does not lose absolute-angle data because generates those data anew with each reading at up to 1,000 times per second. It accumulates increments to measure total angular interval through which shaft has been turned (including unlimited number of complete turns), as long as power remains on.

Leviton, Douglas B.↗
NASA NTRS1993

Results of multiband (L, S, Ku band) propagation measurements and model for high elevation angle land mobile satellite channel

Signal propagation in the land mobile satellite (LMS) service is an important consideration due to its critical impact on the overall economic and commercial viability of the system. At frequencies allocated for LMS systems, shadowing of the line-of-sight (LOS) signal as well as multipath propagation phenomena can severely impair the link availability. In particular, as most of the studies have shown, the shadowing of LOS signal causes long and deep fades in a variety of mobile environments due to the inherent nature of the channel between the satellite and a mobile. Roadside obstacles, such as buildings, trees, utility poles etc., in the immediate vicinity of a mobile and the surrounding terrain are major sources of signal shadowing in LMS links. Therefore, a proper knowledge of link degradation is essential for cost-effective planning of a satellite based mobile communication system. The results of a propagation campaign undertaken to characterize the fading nature of LMS channel at high elevation angles is presented. It was envisaged that one of the most important physical variables contributing to the amount of LOS signal shadowing is the elevation angle of the satellite. At higher elevation angles to the satellite, less obstructions in the direct satellite-to-mobile path would therefore amount to statistically better link availability. Narrowband channel measurements were carried out at three RF frequencies corresponding to L (1.3 GHz), S (2.32/2.45 GHz), and Ku (10.4 GHz) bands. The campaign itself was divided into two phases to observe the effects of seasonal variation of foliage on the roadside trees. Phase measurements were carried out in September 1991 and in April 1992. Some important aspects from the statistical analysis of the propagation data are presented.

Parks, M. A. N.↗
NASA NTRS1993

The Brewster angle effect in SAR polarimetry

For the double bounce case, where the radar signal is reflected twice before returning to the radar antenna, some polarization effects may be observed related to the dielectric constant of the two surfaces causing the reflections. The most noticeable effect would be that the returned signal would be preferentially H polarized. In fact, it may be possible to discern the Brewster angle for both surfaces. The locations of the Brewster angle will depend on the dielectric constant and permittivity of each surface. If it is assumed that both reflections are in the same plane of incidence, and that both surfaces are smooth and flat, there is a straightforward relationship between the degree of linear polarization m and both the dielectric constants of the two reflecting surfaces and the angle of incidence of the illuminating wave: m carat = cos 2(arccot (square root of (R(sub v) / R(sub h)))) where R(sub v,h) are the V and H polarized Fresnel reflection coefficients for two surfaces perpendicular to each other. The degree of linear polarization may be calculated from AIRSAR compressed Stokes data and compared with the given equation. The degree of linear polarization may also be calculated using tree models and compared with AIRSAR data. With further work, it may be possible to use the degree of linear polarization to determine surface parameters of certain imaged areas.

Chapman, B.↗
NASA NTRS1994

Hybrid structured/unstructured grid computations for the F/A-18 at high angle of attack

At high angles of attack, vortical flows play a crucial role in the maintenance of lift for fighter aircraft. However, under certain conditions, the vortical flow can have an adverse effect on the aircraft. On the F/A-18 the LEX vortex can impinge on the tail; at high angles of attack the unsteady flow from vortex bursting can cause structural fatigue on the vertical tails. At high angles of attack, the flow field can be quite complex, and a computational analysis challenging. A full configuration analysis with viscous structured grids can be computationally expensive and the task of generating the requisite grids can be quite difficult. To mitigate these difficulties and provide a medium-fidelity analysis tool, a hybrid structured/unstructured approach was adopted for this work. In this analysis, the formation and roll-up of the LEX vortex is computed with a structured Navier-Stokes solver, and the resulting vortex propagated downstream with an unstructured Euler solver.

Robert T Biedron↗
NASA NTRS1995

The effect of impact angle on craters formed by hypervelocity particles

The Space Power Institute (SPI) at Auburn University has conducted experiments on the effects of impact angle on crater morphology and impactor residue retention for hypervelocity impacts. Copper target plates were set at angles of 30 deg, 45 deg, 60 deg, and 75 deg from the particle flight path. For the 30 deg and 45 deg impacts, in the velocity regime greater than 8 km s(exp -1) the resultant craters are almost identical to normal incidence impacts. The only difference found was in the apparent distribution of particle residue within the crater, and further research is needed to verify this. The 60 deg and 75 deg impacts showed marked differences in crater symmetry, crater lip shape, and particle residue distribution in the same velocity regime. Impactor residue shock fractionation effects have been quantified in first-order. It is concluded that a combination of analysis techniques can yield further information on impact velocity, direction, and angle of incidence.

Hill, David C.↗
NASA NTRS1994

Large-angle cosmic microwave background anisotropies in an open universe

If the universe is open, scales larger than the curvature scale may be probed by observation of large-angle fluctuations in the cosmic microwave background (CMB). We consider primordial adiabatic perturbations and discuss power spectra that are power laws in volume, wavelength, and eigenvalue of the Laplace operator. Such spectra may have arisen if, for example, the universe underwent a period of `frustated' inflation. The resulting large-angle anisotropies of the CMB are computed. The amplitude generally increases as Omega is decreased but decreases as h is increased. Interestingly enough, for all three Ansaetze, anisotropies on angular scales larger than the curvature scale are suppressed relative to the anisotropies on scales smaller than the curvature scale, but cosmic variance makes discrimination between various models difficult. Models with 0.2 approximately less than Omega h approximately less than 0.3 appear compatible with CMB fluctuations detected by Cosmic Background Explorer Satellite (COBE) and the Tenerife experiment and with the amplitude and spectrum of fluctuations of galaxy counts in the APM, CfA, and 1.2 Jy IRAS surveys. COBE normalization for these models yields sigma(sub 8) approximately = 0.5 - 0.7. Models with smaller values of Omega h when normalized to COBE require bias factors in excess of 2 to be compatible with the observed galaxy counts on the 8/h Mpc scale. Requiring that the age of the universe exceed 10 Gyr implies that Omega approximately greater than 0.25, while requiring that from the last-scattering term in the Sachs-Wolfe formula, large-angle anisotropies come primarily from the decay of potential fluctuations at z approximately less than 1/Omega. Thus, if the universe is open, COBE has been detecting temperature fluctuations produced at moderate redshift rather than at z approximately 1300.

Kamionkowski, Marc↗
NASA NTRS1995

Dual Wall Angles Would Enhance Performance Of A Solar Pond

Proposed dual-angle design for Sun-facing wall of solar pond enhances solar-energy-storage performance of pond; increase in performance over that of similar pond with conventional (single-angle) wall estimated to be 25 percent. Design compromises between maximizing heating and minimizing convection. Top part of Sun-facing wall optimized for top colder layer of water, less tendency toward convective mixing. Bottom part of wall optimized for bottom, warmer layer of water, greater tendency towards convection. Optimization involves consideration of both anticipated temperature-vs.-depth profile (affects tendency toward convection) and latitude (affects angle of incidence of solar radiation and rate of heating).

Noever, David A.↗
NASA NTRS1995

Angled injection: Hybrid fluid film bearings for cryogenic applications

A computational bulk-flow analysis for prediction of the force coefficients of hybrid fluid film bearings with angled orifice injection is presented. Past measurements on water-lubricated hybrid bearings with angle orifice injection have demonstrated improved rotordynamic performance with virtual elimination of cross-coupled stiffness coefficients and nul or negative whirl frequency ratios. A simple analysis reveals that the fluid momentum exchange at the orifice discharge produces a pressure rise in the recess which retards the shear flow induced by journal rotation, and consequently, reduces cross-coupling forces. The predictions from the model correlate well with experimental measurements from a radial and 45 deg angled orifice injection, five recess water hybrid bearings (C = 125 microns) operating at 10.2, 17.4, and 24.6 krpm and with nominal supply pressures equal to 4, 5.5, and 7 MPa. An application example for a liquid oxygen six recess/pad hybrid journal bearing shows the advantages of tangential orifice injection on the rotordynamic force coefficients and stability indicator for forward whirl motions and without performance degradation on direct stiffness and damping coefficients. The computer program generated, 'hydrojet,' extends and complements previously developed codes.

SanAndres, Luis↗
NASA NTRS1996

Experimental and Computational Induced Aerodynamics from Missile Jet Reaction Controls at Angles of Attack to 75 Degrees

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine induced aerodynamic effects from jet reaction controls of an advanced air-to-air missile concept. The 75-percent scale model featured independently controlled reaction jets located near the nose and tail of the model. Aerodynamic control was provided by four fins located near the tail of the model. This investigation was conducted at Mach numbers of 0.35 and 0.60, at angles of attack up to 75 deg and at nozzle pressure ratios up to 90. Jet-reaction thrust forces were not measured by the force balance but jet-induced forces were. In addition, a multiblock three-dimensional Navier-Stokes method was used to calculate the flowfield of the missile at angles of attack up to 40 deg. Results indicate that large interference effects on pitching moment were induced from operating the nose jets with the the off. Excellent correlation between experimental and computational pressure distributions and pitching moment were obtained a a Mach number of 0.35 and at angles of attack up to 40 deg.

Capone, Francis J.↗
NASA NTRS1996

X-29A Lateral-Directional Stability and Control Derivatives Extracted From High-Angle-of-Attack Flight Data

The lateral-directional stability and control derivatives of the X-29A number 2 are extracted from flight data over an angle-of-attack range of 4 degrees to 53 degrees using a parameter identification algorithm. The algorithm uses the linearized aircraft equations of motion and a maximum likelihood estimator in the presence of state and measurement noise. State noise is used to model the uncommanded forcing function caused by unsteady aerodynamics over the aircraft at angles of attack above 15 degrees. The results supported the flight-envelope-expansion phase of the X-29A number 2 by helping to update the aerodynamic mathematical model, to improve the real-time simulator, and to revise flight control system laws. Effects of the aircraft high gain flight control system on maneuver quality and the estimated derivatives are also discussed. The derivatives are plotted as functions of angle of attack and compared with the predicted aerodynamic database. Agreement between predicted and flight values is quite good for some derivatives such as the lateral force due to sideslip, the lateral force due to rudder deflection, and the rolling moment due to roll rate. The results also show significant differences in several important derivatives such as the rolling moment due to sideslip, the yawing moment due to sideslip, the yawing moment due to aileron deflection, and the yawing moment due to rudder deflection.

Iliff, Kenneth W.↗
NASA NTRS1997

Exploratory Investigation of Forebody Strakes for Yaw Control of a Generic Fighter with a Symmetric 60 deg Half-Angle Chine Forebody

Forebody strakes were tested in a low-speed wind tunnel to determine their effectiveness producing yaw control on a generic fighter model with a symmetric 60 deg half-angle chine forebody. Previous studies conducted using smooth, conventionally shaped forebodies show that forebody strakes provide increased levels of yaw control at angles of attack where conventional rudders are ineffective. The chine forebody shape was chosen for this study because chine forebodies can be designed with lower radar cross section (RCS) values than smooth forebody shapes. Because the chine edges of the forebody would fix the point of flow separation, it was unknown if any effectiveness achieved could be modulated as was successfully done on the smooth forebody shapes. The results show that use of forebody strakes on a chine forebody produce high levels of yaw control, and when combined with the rudder effectiveness, significant yaw control is available for a large range of angles of attack. The strake effectiveness was very dependent on radial location. Very small strakes placed at the tip of the forebody were nearly as effective as very long strakes. An axial translation scheme provided almost linear increments of control effectiveness.

Ross, Holly M.↗
NASA NTRS1996

Effect of Tilt Angle on the Morphology of SiC Epitaxial Films Grown on Vicinal (0001) SiC Substrates

In this study of 4H-SiC and 6H-SiC epitaxial films we found that film morphology was strongly dependent on the tilt angle of the substrate. Large surface steps (up to 25 nm high) due to step bunching were more prevalent at smaller tilt angles. Also, 4H films were more susceptible than 6H to 3C-SiC inclusions during growth. The lateral growth of steps from screw dislocations in low-tilt-angle substrates demonstrated that step bunching on the atomic scale was anisotropic with respect to growth direction for both 4H-SiC and 6H-SiC. A model explaining this behavior is presented. We observed and directly measured the Burgers vector of a 'super' screw dislocation in a 6H-SiC epilayer.

Powell, J. A.↗
NASA NTRS1997

Angled Injection: Turbulent Flow Hybrid Bearings Comparison to Test Results

Hydrostatic/hydrodynamic (hybrid) journal bearings handling process liquids have limited dynamic stability characteristics and their application as support elements to high speed flexible rotating systems is severely restricted. Measurements on water hybrid bearings with angled orifice injection have demonstrated improved rotordynamic performance with virtual elimination of cross-coupled stiffness coefficients and null or negative whirl frequency ratios. A bulk-flow model for prediction of the static performance and force coefficients of hybrid bearings with angled orifice injection is advanced. The analysis reveals that the fluid momentum exchange at the orifice discharge produces a pressure rise in the hydrostatic recess retards the shear flow induced by journal rotation, and thus, reduces cross-coupling forces. The predictions from the model are compared with experimental measurements for a 45 deg. angled orifice injection, 5 recess water hybrid bearing operating at 10.2, 17.4, and 24.6 krpm and with supply pressures of 4, 5.5, and 7 MPa. The correlations include recess pressures, flow rates, and rotordynamic force coefficients at the journal centered position.

SanAndres, Luis↗
NASA NTRS1997

Flight-Determined Subsonic Longitudinal Stability and Control Derivatives of the F-18 High Angle of Attack Research Vehicle (HARV) with Thrust Vectoring

The subsonic longitudinal stability and control derivatives of the F-18 High Angle of Attack Research Vehicle (HARV) are extracted from dynamic flight data using a maximum likelihood parameter identification technique. The technique uses the linearized aircraft equations of motion in their continuous/discrete form and accounts for state and measurement noise as well as thrust-vectoring effects. State noise is used to model the uncommanded forcing function caused by unsteady aerodynamics over the aircraft, particularly at high angles of attack. Thrust vectoring was implemented using electrohydraulically-actuated nozzle postexit vanes and a specialized research flight control system. During maneuvers, a control system feature provided independent aerodynamic control surface inputs and independent thrust-vectoring vane inputs, thereby eliminating correlations between the aircraft states and controls. Substantial variations in control excitation and dynamic response were exhibited for maneuvers conducted at different angles of attack. Opposing vane interactions caused most thrust-vectoring inputs to experience some exhaust plume interference and thus reduced effectiveness. The estimated stability and control derivatives are plotted, and a discussion relates them to predicted values and maneuver quality.

Iliff, Kenneth W.↗