SEARCH · Engineering Papers

Results for “airfoil”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Improving turbine engine compressor performance retention through airfoil coatings

In order to evaluate the potential effectiveness of coatings in limiting erosive damage to compressor airfoils, an effort was initiated to evaluate candidate coatings for substrate alloys typically used in commercial engine high compressor blades. Laboratory and rig erosion testing of plasma deposited and diffusion coatings described in this paper have shown the potential of a two to four fold improvement in erosion life. The selective application of these coatings to approximately the outer third of the airfoil avoids coating the fatigue critical region of the blade, thus providing erosion resistance potentially without compromising the fatigue strength of the blade. Both the plasma and the diffusion coatings also offer the advantage of low initial cost and a multi-source production base.

Friedrich, L. A.↗

NASA NTRS1981

Icing tunnel tests of a glycol-exuding porous leading edge ice protection system on a general aviation airfoil

Tests were conducted in the Icing Research Tunnel at the NASA Lewis Research Center to determine the characteristics of an ice protection system that distributes a glycol solution onto the leading edge of an airfoil through a porous surface material. Minimum fluid flow rates required to achieve anti-icing (no ice formation) were determined for various flight conditions and angles of attack. The ability of the system to remove ice formed on the airfoil before system activation was also investigated.

Kohlman, D. L.↗

NASA NTRS1980

Design considerations of advanced supercritical low drag suction airfoils

Supercritical low drag suction laminar flow airfoils were laid out for shock-free flow at design freestream Mach = 0.76, design lift coefficient = 0.58, and t/c = 0.13. The design goals were the minimization of suction laminarization problems and the assurance of shock-free flow at freestream Mach not greater than design freestream Mach (for design lift coefficient) as well as at lift coefficient not greater than design lift coefficient (for design freestream Mach); this involved limiting the height-to-length ratio of the supersonic zone at design to 0.35. High design freestream Mach numbers result with extensive supersonic flow (over 80% of the chord) on the upper surface, with a steep Stratford-type rear pressure rise with suction, as well as by carrying lift essentially in front- and rear-loaded regions of the airfoil with high static pressures on the carved out front and rear lower surface.

Pfenninger, W.↗

NASA NTRS1981

Numerical simulation of steady transonic flow about airfoils

A computer code has been developed that couples a fast transonic full-potential AF2 solver with both an efficient integral boundary-layer method and a viscous wedge approximation of the shock/boundary-layer interaction. The efficiency of the coupled analysis methods and the method of coupling has resulted in a uniquely efficient analysis tool. The airfoil geometry is modified by the displacement thickness before the shock and the displacement thickness plus the viscous wedge thickness after the shock by considering the viscous effects as an equivalent transpiration boundary condition. The flow about conventional and supercritical airfoils under moderately strong shock situations has been calculated. Comparisons with experimental data indicate that this viscous correction method has improved the accuracy of the full-potential analysis. Furthermore, the computer time required to obtain a converged solution has been reduced.

Lee, S. C.↗

NASA NTRS1981

On the structure of turbulent wakes and merging shear layers of multielement airfoils

The structure of the attached turbulent flow in the vicinity of a NACA 4412 airfoil equipped with a single-slotted flap was studied. The airfoil/flap configuration was tested at a Mach number of 0.06 and a Reynolds number of 1.3 x 10 to the 6th in a 7- by 10-Foot Wind Tunnel. Surface-pressure measurements were made on the main airfoil and on the flap. Detailed measurements, obtained using a high-spatial-resolution laser Doppler anemometer, were made of the mean velocity flow field and of the second-order statistical quantities (Reynolds stresses) in the boundary layers, wakes, and merging shear layers. The experimental observations are compared with theoretical predictions of pressure, mean velocity, and Reynolds stress.

Olson, L. E.↗

NASA NTRS1981

Application of unsteady airfoil theory to rotary wings

A clarification is presented on recent work concerning the application of unsteady airfoil theory to rotary wings. The application of this theory may be seen as consisting of four steps: (1) the selection of an appropriate unsteady airfoil theory; (2) the resolution of that velocity which is the resultant of aerodynamic and dynamic velocities at a point on the elastic axis into radial, tangential and perpendicular components, and the angular velocity of a blade section about the deformed axis; (3) the expression of lift and pitching moments in terms of the three components; and (4) the derivation of explicit expressions for the components in terms of flight velocity, induced flow, rotor rotational speed, blade motion variables, etc.

Kaza, K. R. V.↗

NASA NTRS1953

Analytical Investigation of Icing Limit for Diamond-Shaped Airfoil in Transonic and Supersonic Flow

Calculations have been made for the icing limit of a diamond airfoil at zero angle of attack in terms of the stream Mach number, stream temperature, and pressure altitude. The icing limit is defined as a wetted-surface temperature of 320 F and is related to the stream conditions by the method of Hardy. The results show that the point most likely to ice on the airfoil lies immediately behind the shoulder and is subject to possible icing at Mach numbers as high as 1.4.

Callaghan, Edmund E.↗

NASA NTRS1952

Preliminary Results of Cyclical De-Icing of a Gas-Heated Airfoil

An NACA 65(sub 1)-212 airfoil of 8-foot chord was provided with a gas-heated leading edge for investigations of cyclical de-icing. De-icing was accomplished with intermittent heating of airfoil segments that supplied hot gas to chordwise passages in a double-skin construction. Ice removal was facilitated by a spanwise leading-edge parting strip which was continuously heated from the gas-supply duct. Preliminary results demonstrate that satisfactory cyclical ice removal occurs with ratios of cycle time to heat-on period (cycle ratio) from 10 to 26. For minimum runback, efficient ice removal, and minimum total heat input, short heat-on periods of about 15 seconds with heat-off periods of 260 seconds gave the best results. In the range of conditions investigated, the prime variables in the determination of the required heat input for cyclical ice removal were the air temperature and the cycle ratio; heat-off period, liquid water content, airspeed, and angle of attack had only secondary effects on heat input rate.

Gray, V. H.↗

NASA NTRS1951

Comparison of Heat Transfer from Airfoil in Natural and Simulated Icing Conditions

An investigation of the heat transfer from an airfoil in clear air and in simulated icing conditions was conducted in the NACA Lewis 6- by 9-foot icing-research tunnel in order to determine the validity of heat-transfer data as obtained in the tunnel. This investiation was made on the same model NACA 65,2-016 airfoil section used in a previous flight study, under similar heating, icing, and operating conditions. The effect of tunnel turbulence, in clear air and in icingwas indicated by the forward movement of transition from laminar to turbulent heat transfer. An analysis of the flight results showed the convective heat transfer in icing to be considerably different from that measured in clear air and. only slightly different from that obtained in the icing-research tunnel during simulated icing.

Gelder, Thomas F.↗

NASA NTRS1981

Wind-tunnel results for a modified 17-percent-thick low-speed airfoil section

Wind-tunnel tests were conducted in the Langley low-turbulence pressure tunnel to evaluate the effects on performance of modifying a 17-percent-thick low-speed airfoil. The airfoil contour was altered to reduce the pitching-moment coefficient by increasing the forward loading and to increase the climb lift-drag ratio by decreasing the aft upper surface pressure gradient. The tests were conducted over a Mach number range from 0.07 to 0.32, a chord Reynolds number range 1.0 x 10 to the 6th power to 12.0 x 10 to the 6th power, and an angle-of-attack range from about -10 deg to 20 deg.

Mcghee, R. J.↗

NASA NTRS1981

Experimental investigation of a transonic potential flow around a symmetric airfoil

Experimental flow investigations on smooth airfoils were done using numerical solutions for transonic airfoil streaming with shockless supersonic range. The experimental flow reproduced essential sections of the theoretically computed frictionless solution. Agreement is better in the expansion part of the of the flow than in the compression part. The flow was nearly stationary in the entire velocity range investigated.

Hiller, W. J.↗

NASA NTRS1981

Low Reynolds number airfoil survey, volume 1

The differences in flow behavior two dimensional airfoils in the critical chordlength Reynolds number compared with lower and higher Reynolds number are discussed. The large laminar separation bubble is discussed in view of its important influence on critical Reynolds number airfoil behavior. The shortcomings of application of theoretical boundary layer computations which are successful at higher Reynolds numbers to the critical regime are discussed. The large variation in experimental aerodynamic characteristic measurement due to small changes in ambient turbulence, vibration, and sound level is illustrated. The difficulties in obtaining accurate detailed measurements in free flight and dramatic performance improvements at critical Reynolds number, achieved with various types of boundary layer tripping devices are discussed.

Carmichael, B. H.↗

NASA NTRS1979

Natural laminar flow airfoil analysis and trade studies

An analysis of an airfoil for a large commercial transport cruising at Mach 0.8 and the use of advanced computer techniques to perform the analysis are described. Incorporation of the airfoil into a natural laminar flow transport configuration is addressed and a comparison of fuel requirements and operating costs between the natural laminar flow transport and an equivalent turbulent flow transport is addressed.

Source record↗

NASA NTRS1982

Application of an airfoil stall flutter computer prediction program to a three-dimensional wing: Prediction versus experiment

An aerodynamic computer code, capable of predicting unsteady and C sub m values for an airfoil undergoing dynamic stall, is used to predict the amplitudes and frequencies of a wing undergoing torsional stall flutter. The code, developed at United Technologies Research Corporation (UTRC), is an empirical prediction method designed to yield unsteady values of normal force and moment, given the airfoil's static coefficient characteristics and the unsteady aerodynamic values, alpha, A and B. In this experiment, conducted in the PSU 4' x 5' subsonic wind tunnel, the wing's elastic axis, torsional spring constant and initial angle of attack are varied, and the oscillation amplitudes and frequencies of the wing, while undergoing torsional stall flutter, are recorded. These experimental values show only fair comparisons with the predicted responses. Predictions tend to be good at low velocities and rather poor at higher velocities.

Muffoletto, A. J.↗

NASA NTRS1982

NASA Langley laminar flow control airfoil experiment

The design and construction of an advanced swept supercritical airfoil for commercial aircraft to be tested in a transonic wind tunnel is described. The swept LFC airfoil was designed for a given thickness ratio and lift coefficient, with emphasis placed on high critical Mach number with shock-free flow. It is compatible with satisfactory low speed and buffeting characteristics and minimizing the suction laminarization. Further emphasis was placed on achieving shock-free flow over a wide range of off-design conditions including trailing edge flap control. The requirements and design of the suction system and modifications to the Langley 8 foot transonic pressure tunnel is briefly described. Contouring of nonporous test section walls for free air simulation and flow quality improvements is included.

Harvey, W. D.↗

NASA NTRS1982

Investigation of passive shock wave-boundary layer control for transonic airfoil drag reduction

The passive drag control concept, consisting of a porous surface with a cavity beneath it, was investigated with a 12-percent-thick circular arc and a 14-percent-thick supercritical airfoil mounted on the test section bottom wall. The porous surface was positioned in the shock wave/boundary layer interaction region. The flow circulating through the porous surface, from the downstream to the upstream of the terminating shock wave location, produced a lambda shock wave system and a pressure decrease in the downstream region minimizing the flow separation. The wake impact pressure data show an appreciably drag reduction with the porous surface at transonic speeds. To determine the optimum size of porosity and cavity, tunnel tests were conducted with different airfoil porosities, cavities and flow Mach numbers. A higher drag reduction was obtained by the 2.5 percent porosity and the 1/4-inch deep cavity.

Nagamatsu, H. T.↗

NASA NTRS1981

Analytical studies of new airfoils for wind turbines

Computer studies were conducted to analyze the potential gains associated with utilizing new airfoils for large wind turbine rotor blades. Attempts to include 3-dimensional stalling effects were inconclusive. It is recommended that blade pressure measurements be made to clarify the nature of blade stalling. It is also recommended that new laminar flow airfoils be used as rotor blade sections.

Wentz, W. H., Jr.↗

NASA NTRS1982

An assessment of a modified potential flow code for calculating the effect of small geometric change on the pressure and forces of supercritical airfoils

Wind-tunnel test data for two closely related supercritical airfoils were compared with calculations obtained from a nonconservative, potential flow code over a Mach number range from 0.20 to 0.80. The potential flow code includes an iterated, integral boundary-layer correction. The theoretical pressure distributions correlated more closely with the experimental pressure distributions when the flow was entirely subsonic or subsonic with a small supersonic zone than when the flow contained a large supersonic zone. The predicted drag level was below the experimental values at nearly all test conditions and the difference in drag level for the two airfoils was not accurately predicted.

Hicks, R. M.↗