Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ZINC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Deposition of aluminum-doped zinc oxide thin films for optical applications using rf and dc magnetron sputter deposition

Aluminum-doped zinc oxide films were deposited by dc and rf magnetron sputtering from ZnO(98%)Al{sub 2}O{sub 3}(2%) target at room temperature on silicon and glass substrates under a variety of process conditions with the goal of attaining the highest transmittance and lowest resistivity for photovoltaic applications. The magnetron power and pressure were varied. For many dielectric deposition systems, added oxygen is necessary to achieve the appropriate stoichiometry. The effect of oxygen on film properties was then studied by varying the oxygen partial pressure from 1.5x10{sup -5} to 4.0x10{sup -5} T at a constant Ar pressure, with the result that any added oxygen was deleterious. Films deposited under power, pressure, and low-oxygen conditions were then characterized for electrical and optical properties. Following this, the dc and rf sputtered films were annealed at up to 400 deg. C seconds using rapid thermal annealing (RTA), and the influence of annealing on resistivity, transmittance, band gap, as well as grain growth and stress was studied. The effect of RTA was immediate and quite significant on dc films while the effect on rf films was not as profound. As-deposited rf films had a higher average transmittance (87%) and lower resistivity (5.5x10{sup -4} {Omega} cm) compared to as-deposited dc films (84.2% and 8.9x10{sup -4} {Omega} cm). On the other hand, after RTA at 400 deg. C for 60 s, dc films exhibited better average transmittance (92.3%) and resistivity (2.9x10{sup -4} {Omega} cm) than rf films (90.7% and 4.0x10{sup -4} {Omega} cm). The band gap of dc films increased from 3.55 to 3.80 eV while that of rf films increased from 3.76 to 3.85 eV. Finally, dc and rf films were textured in 0.1% HCl and compared to U-type Asahi glass for resistivity and transmittance.

36 MATERIALS SCIENCE↗

Properties of double-layered Ga-doped Al-zinc-oxide/titanium-doped indium-tin-oxide thin films prepared by dc magnetron sputtering applied for Si-based thin film solar cells

In this article, Ga-doped Al-zinc-oxide (GAZO)/titanium-doped indium-tin-oxide (ITIO) bi-layer films were deposited onto glass substrates by direct current (dc) magnetron sputtering. The bottom ITIO film, with a thickness of 200 nm, was sputtered onto the glass substrate. The ITIO film was post-annealed at 350 deg. C for 10-120 min as a seed layer. The effect of post-annealing conditions on the morphologies, electrical, and optical properties of ITIO films was investigated. A GAZO layer with a thickness of 1200 nm was continuously sputtered onto the ITIO bottom layer. The results show that the properties of the GAZO/ITIO films were strongly dependent on the post-annealed conditions. The spectral haze (T{sub diffuse}/T{sub total}) of the GAZO/ITIO bi-layer films increases upon increasing the post-annealing time. The haze and resistivity of the GAZO/ITIO bi-layer films were improved with the post-annealed process. After optimizing the deposition and annealing parameters, the GAZO/ITIO bi-layer film has an average transmittance of 83.20% at the 400-800 nm wavelengths, a maximum haze of 16%, and the lowest resistivity of 1.04 x 10{sup -3}{Omega} cm. Finally, the GAZO/ITIO bi-layer films, as a front electrode for silicon-based thin film solar cells, obtained a maximum efficiency of 7.10%. These encouraging experimental results have potential applications in GAZO/ITIO bi-layer film deposition by in-line sputtering without the wet-etching process and enable the production of highly efficient, low-cost thin film solar cells.

36 MATERIALS SCIENCE↗

On the possibility to grow zinc oxide-based transparent conducting oxide films by hot-wire chemical vapor deposition

Hot-wire chemical vapor deposition (HW-CVD) was applied to grow zinc oxide (ZnO)-based transparent conducting oxide (TCO) films. Indium (In)-doped ZnO films were deposited using a cold wall pulsed liquid injection CVD system with three nichrome wires installed at a distance of 2 cm from the substrate holder. The wires were heated by an AC current in the range of 0–10 A. Zn and In 2,2,6,6-tetramethyl-3,5-heptanedionates dissolved in 1,2-dimethoxyethane were used as precursors. The hot wires had a marked effect on the growth rates of ZnO, In-doped ZnO, and In{sub 2}O{sub 3} films; at a current of 6–10 A, growth rates were increased by a factor of ≈10–20 compared with those of traditional CVD at the same substrate temperature (400 °C). In-doped ZnO films with thickness of ≈150 nm deposited on sapphire-R grown at a wire current of 9 A exhibited a resistivity of ≈2 × 10{sup −3} Ωcm and transparency of >90% in the visible spectral range. These initial results reveal the potential of HW-CVD for the growth of TCOs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High performance Schottky diodes based on indium-gallium-zinc-oxide

Indium-gallium-zinc-oxide (IGZO) Schottky diodes exhibit excellent performance in comparison with conventional devices used in future flexible high frequency electronics. In this work, a high performance Pt IGZO Schottky diode was presented by using a new fabrication process. An argon/oxygen mixture gas was introduced during the deposition of the Pt layer to reduce the oxygen deficiency at the Schottky interface. The diode showed a high barrier height of 0.92 eV and a low ideality factor of 1.36 from the current–voltage characteristics. Even the radius of the active area was 0.1 mm, and the diode showed a cut-off frequency of 6 MHz in the rectifier circuit. Using the diode as a demodulator, a potential application was also demonstrated in this work.

42 ENGINEERING↗

Intense pulsed light annealing of copper zinc tin sulfide nanocrystal coatings

A promising method for forming the absorber layer in copper zinc tin sulfide [Cu{sub 2}ZnSnS{sub 4} (CZTS)] thin film solar cells is thermal annealing of coatings cast from dispersions of CZTS nanocrystals. Intense pulsed light (IPL) annealing utilizing xenon flash lamps is a potential high-throughput, low-cost, roll-to-roll manufacturing compatible alternative to thermal annealing in conventional furnaces. The authors studied the effects of flash energy density (3.9–11.6 J/cm{sup 2}) and number of flashes (1–400) during IPL annealing on the microstructure of CZTS nanocrystal coatings cast on molybdenum-coated soda lime glass substrates (Mo-coated SLG). The annealed coatings exhibited cracks with two distinct linear crack densities, 0.01 and 0.2 μm{sup −1}, depending on the flash intensity and total number of flashes. Low density cracking (0.01 μm{sup −1}, ∼1 crack per 100 μm) is caused by decomposition of CZTS at the Mo-coating interface. Vapor decomposition products at the interface cause blisters as they escape the coating. Residual decomposition products within the blisters were imaged using confocal Raman spectroscopy. In support of this hypothesis, replacing the Mo-coated SLG substrate with quartz eliminated blistering and low-density cracking. High density cracking is caused by rapid thermal expansion and contraction of the coating constricted on the substrate as it is heated and cooled during IPL annealing. Finite element modeling showed that CZTS coatings on low thermal diffusivity materials (i.e., SLG) underwent significant differential heating with respect to the substrate with rapid rises and falls of the coating temperature as the flash is turned on and off, possibly causing a build-up of tensile stress within the coating prompting cracking. Use of a high thermal diffusivity substrate, such as a molybdenum foil (Mo foil), reduces this differential heating and eliminates the high-density cracking. IPL annealing in presence of sulfur vapor prevented both low- and high-density cracking as well as blistering. However, grain growth was limited even after annealing with 400 flashes. This lack of grain growth is attributed to a difficulty of maintaining high sulfur vapor pressure and absence of alkali metal impurities when Mo foil substrates are used.

36 MATERIALS SCIENCE↗

Fluorescence of Zinc Complex with N,N'-Bis(5-Bromosalicylidene)Ethylenediamine

A Zn(II) complex with N,N'-bis(5-bromosalicylidene)ethylenediamine exhibiting intense visible blue luminescence is synthesized. It is found that the zinc complex fluoresces at 293 K in both polycrystalline form and in solutions (λ{sub max} = 440 and 450 nm, respectively); the relative fluorescence quantum yields of the complex are determined in dilute ethanol, dimethylformamide, and dimethylsulfoxide solutions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Zinc oxide hollow microstructures and nanostructures formed under hydrothermal conditions

Zinc oxide low-dimensional hollow structures in the form of hexagonal plates with holes at the center of the {l_brace}0001{r_brace} facets are synthesized in the course of the low-temperature interaction of ZnO precursors with aqueous solutions of potassium fluoride under hydrothermal conditions. Crystals have the shape of single-walled or multiwalled 'nuts.' The high optical quality of the structures is confirmed by cathodoluminescence data at room temperature. The mechanism of the formation of ZnO 'nanonuts' and products of the interaction of the ZnO precursors with KF is proposed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nanocrystalline zinc oxide: Pyrolytic synthesis and spectroscopic characteristics

Nanocrystalline and microcrystalline ZnO powders are synthesized by the pyrolysis of organic zinc salts in the presence of a reducing catalyst represented by a porous cellulose carrier. The specimens obtained are characterized by X-ray powder diffraction, energy dispersive analysis, scanning electron microscopy, and pulse cathodoluminescence. Lasing characteristics of the specimens are studied. The synthesis conditions, under which specimens with the crystallite morphology optimal for a low-threshold lasing are obtained, are found.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Change in the structural imperfection of lithium niobate crystals doped with zinc

The changes in the degree of structural imperfection of lithium niobate (LiNbO{sub 3}) single crystals with an increase in the Li content and doping with zinc (to 1 wt %) have been investigated by the nonlinear optics methods and Raman spectroscopy. The conversion of broadband IR radiation in LiNbO{sub 3} crystals under noncritical (90°) phase-matching condition with vector interactions implemented is investigated. It is shown that the conversion efficiency, spectral width, and the position of maximum in the converted radiation spectrum depend on the ratio R = Li/Nb in LiNbO{sub 3} crystal and the impurity concentration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Experimental and Theoretical Analyses of Zinc-Vacancy-Induced Room-Temperature Ferromagnetism in ZnO Films

Room-temperature ferromagnetism (RTFM) has been observed in RF magnetron sputtered ZnO films with O{sub 2} as an auxiliary gas after annealing. The films exhibit hexagonal wurtzite structure and observable ferromagnetism. A maximum of saturation magnetization of 4.75 emu/cm{sup 3} is obtained. The zinc vacancies are believed as the RTFM origin, and oxygen vacancies are not an incentive of magnetization of the ZnO films. Theoretical study based on first principles calculation is performed for better understanding of the RTFM in substance. The intrinsic physical mechanism of regulating the ferromagnetic of the ZnO film is analyzed in detail.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analysis of proton single-particle properties of zinc and germanium isotopes

Experimental proton single-particle energies in the vicinity of the Fermi energy for stable zinc and germanium isotopes are analyzed on the basis the dispersive optical model. The values found for the parameters of the dispersive optical potential are corrected with the aim of matching the total number of protons that is calculated with the aid of the function of Bardeen-Cooper-Schrieffer theory for the occupation probability for single-particle orbits with the charge number Z of the nucleus. The parameters of the dispersive optical potential are extrapolated on the basis of physically motivated arguments to the region of unstable isotopes in which the number N ranges between 34 and 50, and single-particle spectra are predicted by means of calculations with these parameters.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

The influence of thermal annealing on the optical properties of nanocrystalline zinc sulfide films

The influence of thermal annealing on the photoluminescence, electroluminescence, and the transmission and reflection spectra in nanocrystalline zinc sulfide films has been studied. All the samples exhibit a broad emission band, the intensity of which depends on the annealing temperature. It is shown that luminophors, the crystal lattice of which includes imperfections that appeared in the transition from wurtzite to sphalerite, feature the highest emission intensity.

36 MATERIALS SCIENCE↗

Heat induced nanoforms of zinc oxide quantum dots and their characterization

In our studies we observed heat induced phase transitions of Zinc oxide quantum dots at 60, 200, 360 and 400 Degree-Sign C, where all the transitions were irreversible except the transition at 60 Degree-Sign C which wasa reversible one. The phase transition at 60 Degree-Sign C indicated a heat induced conformational change which was supported here by studying polarizing micrographs of ZnO quantum dots thin film. The X-ray diffraction studies of the sample fired at different temperatures as indicated by the thermal analysis were performed in order to understand the changes occurred due to transitions. The study also indicated a new and simple approach to develop ZnO nanorods by just thermal decomposition of the ZnO quantum dots firing in furnace at 200 Degree-Sign C with 2h soaking. In order to have a proper insight of the structural changes we performed scanning electron microscopy. Optical characterization was done by UV-Vis and fluorescence spectrophotometer.

36 MATERIALS SCIENCE↗

Mapping of two-photon luminescence amplification in zinc-oxide microstructures

The mapping of two-photon excited luminescence in aggregations of free-standing zinc oxide microrods has been carried out at room temperature. Two-photon luminescence spectra in the excitonic region for individual microrods have been recorded. The luminescence intensity exhibits a power-law dependence on the optical pump power with the exponent n > 2. This fact, along with the existence of a threshold power above which the dependence in the exciton region deviates from a quadratic one, indicates the onset of light amplification in individual ZnO microrods and the conditions preceding laser oscillation.

36 MATERIALS SCIENCE↗

Influence of doping with third group oxides on properties of zinc oxide thin films

The study of modifications in structural, optical and electrical properties of vacuum evaporated zinc oxide thin films on doping with III group oxides namely aluminum oxide, gallium oxide and indium oxide are reported. It was observed that all the films have transmittance ranging from 85 to 95%. The variation in optical properties with dopants is discussed. On doping the film with III group oxides, the conductivity of the films showed an excellent improvement of the order of 10{sup 3} {Omega}{sup -1} cm{sup -1}. The measurements of activation energy showed that all three oxide doped films have 2 donor levels below the conduction band.

36 MATERIALS SCIENCE↗

Antireflective nanostructured zinc oxide arrays produced by pulsed electrodeposition

Conditions for the pulsed electrochemical deposition of nanostructured zinc oxide arrays with a certain morphology, crystal structure, and optical properties from aqueous electrolytes onto substrates of transparent electrically conducting tin dioxide and on single-crystal silicon wafers with built-in homojunctions are studied in order to develop antireflection coatings for solar cells. It is shown that it is possible to obtain single-layer planar antireflection coatings or arrays of nanorods of this material, both having the form of hexagonal prisms and exhibiting the moth-eye effect.

36 MATERIALS SCIENCE↗

n-ZnO/p-CuI barrier heterostructure based on zinc-oxide nanoarrays formed by pulsed electrodeposition and SILAR copper-iodide films

A p-CuI/n-ZnO barrier structure is investigated as a promising base diode structure for a semitransparent near-ultraviolet detector. We analyze the crystal structure and electrical and optical properties of zinc-oxide nanoarrays electrodeposited in the pulsed mode and copper-iodide films formed by the successive ionic layer adsorption and reaction (SILAR) method, which were used as the basis for an n-ZnO/p-CuI barrier heterostructure sensitive to ultraviolet radiation in the spectral range of 365–370 nm. Using the I–V characteristics, a shunting resistance of R{sub sh} · S{sub c} = 879 Ω cm{sup 2}, a series resistance of R{sub s} · S{sub c} = 8.5 Ω cm{sup 2}, a diode rectification factor of K = 17.6, a rectifying p–n-junction barrier height of Φ = 1.1 eV, and a diode ideality factor of η = 2.4 are established. It is demonstrated that at low forward biases (0 V < {sup U} < 0.15 V), the effects of charge-carrier recombination and tunneling are equal. As the bias increases above 0.15 V, the tunneling–recombination transport mechanism starts working. The diode saturation current J{sub 0} is found to be 6.4 × 10{sup –6} mA cm{sup –2} for recombination and tunneling charge-carrier transport and 2.7 × 10{sup –3} mA cm{sup –2} for tunneling–recombination charge-carrier transport.

36 MATERIALS SCIENCE↗

Study of the Effect of Doping with Iron on the Luminescence of Zinc-Selenide Single Crystals

The effect of doping with iron (thermal diffusion from a surface) on the luminescence of zinc-selenide single crystals in the wavelength range 0.44–0.72 μm and on the spatial distribution of luminescence centers are studied. By means of two-photon confocal microscopy, planar and volume maps of edge (exciton) and impurity–defect luminescence in the above-indicated spectral range are obtained for both doped and undoped crystals. It is shown that crystal regions containing a high iron concentration exhibit low-intensity luminescence in this range. It is found that, in the process of diffusion, several types of impurity–defect centers distributed in a complex way within the crystal bulk are formed. The nature of these centers is discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗