Measurements of total hemispherical emittance for chromel and for alumel wires
Measurement of total hemispherical emittance for chromel and alumel thermocouple wires in inert atmosphere at high temperatures
Harvey, W. D.↗
SEARCH · Engineering Papers
Results for “THERMOCOUPLES”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Radioisotope thermoelectric generator optimization technique
Grand tour missions radioisotope thermoelectric generator power source, presenting optimization technique for hot thermocouple junction operation
Leonard, W. D.↗
Deposition temperature of evaporated Permalloy films
Evaporated Permalloy films deposition temperature measurement by vacuum evaporated Chromel- constantan thin film thermocouple, noting temperature difference between film and glass substrate
Bartran, D. S.↗
Thermal Analysis Methods and Basic Heat-Transfer Data for a Turbulent Heating Flight Experiment at Mach 20 (Reentry F)
A heat-transfer experiment was flight conducted on a 5 deg half-angle cone, 396.2 cm (13 ft) in length, as it entered the sensible atmosphere under laminar, transitional, and turbulent boundary-layer conditions at a free-stream Mach number of about 20. Accurate turbulent-heat-transfer data with natural transition were obtained for correlation with theories in regions of simultaneous high Mach number, Reynolds number, enthalpy, and total-to-wall temperature ratio. Temperatures were measured at four depths through the 15.24-mm-thick (0.600-in.) beryllium wall. Experimental heating rates at 20 stations on the cone were determined independently from the outermost temperature measurement and from the temperature measurement at the second depth by a single-thermocouple inverse method and also from the temperature histories at all four depths by an integral method. The thermal data analysis procedure, associated problems, and results are presented herein.
Howard, Floyd G.↗
Soldering iron temperature indicator
Thermocouple implanted in metal mass simulates heat transfer characteristics of connection which is to be soldered. Light signals indicate whether temperature is right, too high, or too low.
Baker, C. D.↗
Space shuttle: Heat transfer rate measurements on Convair booster (B-15B-2) and North American Rockwell orbiter (161B) at nominal Mach number of 8
Plotted and tabulated data from the thin-skin thermocouple phase of an experimental test program are presented. These data are representative of three events of simulated flight and are described as booster-orbiter ascent heating data, booster reentry heating data, and orbiter reentry heating data. The test was conducted in a 50-inch hypersonic tunnel b at a nominal Mach number of 8 and free-stream Reynolds number range of 700,000 to 3,700,000 per foot. The model employed was a 0.009 scale replica of the Convair B-15B-2 booster and North American Rockwell 161B orbiter.
Warmbrod, J. D.↗
Space shuttle: Heat transfer rate measurements of North American Rockwell orbiter (161B) at nominal Mach number of 8
Plots and tables which determine detailed heat transfer distributions on phase B space shuttle configurations are presented. A thin-skinned thermocouple was used to measure the reentry events of the delta wing orbiter. Data was obtained at a nominal Mach number of 8 and free stream Reynolds numbers ranging from 0.83 x 10 to the 6th power to 3.76 x 10 to the 6th power per foot. Angle of attack was varied from -5 to 50 degrees.
Warmbrod, J. D.↗
Improved fluid dynamics similarity, analysis and verification. Part 5: Analytical and experimental studies of thermal stratification phenomena
The stratification behavior of a contained fluid subjected to transient free convection heat transfer was studied. A rectangular vessel was employed with heat transfer from two opposite walls of the vessel to the fluid. The wall temperature was increased suddenly to initiate the process and was then maintained constant throughout the transient stratification period. Thermocouples were positioned on a post at the center of the vessel. They were adjusted so that temperatures could be measured at the fluid surface and at specific depths beneath the surface. The predicted values of the surface temperature and the stratified layer thickness were found to agree reasonably well with the experimental measurements. The experiments also provided information on the transient centerline temperature distribution and the transient flow distribution.
Winter, E. R. F.↗
Investigations of high power problems in space shuttle antenna designs
A study program is discussed which includes a survey of industry and government laboratories and was undertaken to determine the state of the art in dealing with problems of high power levels in reentry antenna design. A laboratory program to develop techniques for testing dielectric materials for effects on RF transmission is also considered, with emphasis on high power applications in space and reentry flights. The study program resulted in a set of guidelines for avoiding breakdown in antenna design. A discussion of temperature effects on dielectric breakdown is also given. From the laboratory program, a description is presented of techniques for (1) heating with a carbon arc image furnace, (2) temperature measurement (using thermocouples and an infrared pyrometer), (3) mass spectrometric monitoring of outgassing, (4) testing for RF breakdown in both heated dielectrics and the dielectric/air and dielectric/plasma interfaces. Data and observations are reported from technique development using candidate shuttle materials falling into three categories: (1) lightweight refractory foams, (2) dense RF window materials, and (3) ablative materials.
Taylor, W. C.↗
Shuttle ascent and shock impingement aerodynamic heating studies
The collection and analysis of aerodynamic heating data obtained from shock impingement experimental investigation were completed. The data were categorized into four interference areas; fin leading edge, wing/fuselage fin/plate corners, and space shuttle configurations. The effects of shock impingement were found to increase the heating rates 10 to 40 times the undisturbed values. A test program was completed at NASA/Langley Research Center to investigate the magnitudes and surface patterns of the mated shock interference flowfield. A 0.0065 scale thin-skin model of the MDAC 256-20 space shuttle booster mated with a Stycast model of the MDAC Internal tank orbiter was tested in the 20-inch M=6 tunnel, the 31-inch M=10 tunnel, and the 48-inch Unitary Plan Tunnel. The gap region of the ascent configuration was the principal area of interest where both thermocouple and phase-change paint data were obtained. Pressure and heat transfer distributions data on the leeward surface of a 75-degree sweep slab delta wing are presented. The effects of surface roughness on boundary layer transition and aerodynamic heating were investigated.
Lanning, W. D.↗
Flight-test results from two total temperature probes for air-data measurements up to 2014 K (3625 R)
An experimental temperature probe package containing a fluidic oscillator temperature probe and a shielded thermocouple temperature probe was tested during several X-15 flights. The X-15 flights provided greatly varying test conditions, including a wide range of rapidly changing total temperatures and Mach numbers which extended from subsonic to hypersonic speeds. Within restricted ranges of free-stream Mach number, free-stream unit weight flow, and local stagnation pressure, both probes yielded ramp outputs of temperature parallel to ramp inputs of free-stream total temperature. Within these ranges both probes were used to determine total temperature in the Mach 6 temperature environment. Because ambient temperature was known, both probes were used to estimate velocity and Mach number.
Nugent, J.↗
Aerothermodynamic measurements for space shuttle configuration in hypersonic wind tunnels
The effect of shuttle configuration geometry, angle of attack, and free stream flow conditions on the heat-transfer distribution as influenced by three-dimensional effects, the wing-fuselage shock-interaction, and resultant wing-impingement phenomena are examined. In addition, the data provided information regarding the flow field in the vicinity of the nose and boundary layer transition in the plane of symmetry of the fuselage. The data included measurements of the surface pressure, the heat transfer rate distributions, (using models instrumented with thermocouples and models painted with thermographic phosphor) and schlieren and shadowgraph photographs. Posttest photographs of the painted models supplemented the heat transfer data.
Bertin, J. J.↗
Hybrid TE panel test results
Test results are presented for a nine couple (3 x 3 array) thermoelectric panel of hybrid thermocouples. In the hybrid couple, a hollow cylinder of p-type Si-Ge is used to encapsulate a segmented PbTe/Si-Ge n-leg. The hybrid couple is predicted to offer a 10- to 15-percent improvement in performance relative to all Si-Ge couples. The efficiency, output power, and internal resistance of the panel as well as the resistances of the individual hybrid couples are presented as a function of test time covering a period of more than 2600 hours. Initial test results indicated hybrid couple performance consistent with design predictions. Extraneous resistance ranged from 20 to 25% of the hybrid couple thermoelectric resistance.
Bifano, W. J.↗
Testing superalloys at 2000 (1367) and 2200 F (1478 K) in a Mach 4.6 airstream
Seven superalloy models were tested in a plasma arc tunnel facility. The test models were 3 in. (7.62cm) square flat surfaces (nominally 0.01 to 0.02 in. (0.0254 to 0.0508 cm) thick) held in a water-cooled wedge holder at a 60 deg (1.05 rad) angle of attack. The models were cycled 25 times (two were cycled 50 times) for 10 min each cycle in a Mach 4.6 test stream with the model leading edge temperature maintained at 2200 F (1478 K) (one at 2000 F (1367 K)). Backface temperatures were measured with four platinum-platinum 10% rhodium thermocouples and the front surface temperatures with an optical pyrometer. Four different nickel base alloy materials and one cobalt material were evaluated.
Land, D. W.↗
Combustion anomalies in stop-restart firing of hybrid rocket engines
An experimental investigation of the restart process of an oxygen-Plexiglas hybrid rocket demonstrated that preheating the fuel (as a consequence of a previous ignition and a temporary extinguishment) significantly increases the rate of chamber pressurization and produces regression rate overshoots during reignition. Higher rates of chamber pressurization measured during the restart transient imply faster instantaneous regression rates of the fuel during restart. Transient periods following the initial ignition and the restart after a two-second shutdown were observed for four experimental tests. Thermocouples were embedded in the fuel to record subsurface temperature histories. A mathematical model of the thermal processes in the fuel and the events that occur during an experimental firing was developed to calculate the regression rate transients. Quantitative agreement with experimental results was obtained by making nominal corrections to the calculated convective and radiative heating rates.
Saraniero, M. A.↗
Studies of thermionic materials for space power applications
Service life tests of LC-8 and LC-9 carbide-fueled thermionic converters are discussed. Post operational tests of the converters to show emitter diametric change, microstructures of cladding and fuel, and analysis of fuel composition are described. The fabrication and performance of high temperature thermocouples used in the test procedures are included.
Source record↗
Analytical design of sensors for measuring during terminal phase of atmospheric temperature planetary entry
An analytical study was conducted to develop a sensor for measuring the temperature of a planetary atmosphere from an entry vehicle traveling at supersonic speeds and having a detached shock. Such a sensor has been used in the Planetary Atmosphere Experiments Test Probe (PAET) mission and is planned for the Viking-Mars mission. The study specifically considered butt-welded thermocouple sensors stretched between two support posts; however, the factors considered are sufficiently general to apply to other sensors as well. This study included: (1) an investigation of the relation between sensor-measured temperature and free-stream conditions; (2) an evaluation of the effects of extraneous sources of heat; (3) the development of a computer program for evaluating sensor response during entry; and (4) a parametric study of sensor design characteristics.
Millard, J. P.↗
On-the-shaft data systems for rotating engine components
Two rotating data systems for engine component testing which demonstrate the techniques of on-the-shaft microelectronic signal conditioning and rotary transformer power- and data-transfer are described. (1) A digital data system provides 69 channels of 1100 C maximum thermocouple data with less than 0.5 percent error from a turbine test rig rotating at speeds up to 9000 rpm. (2) An analog data system amplifies and transfers 72 channels of dynamic strain data with less than 5 percent error from a compressor rig at speeds above 14,000 rpm.
Lesco, D. J.↗