Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Laser-induced fluorescence of green plants. I - A technique for the remote detection of plant stress and species differentiation

The laser-induced fluorescence (LIF) of green plants was evaluated as a means of remotely detecting plant stress and determining plant type. Corn and soybeans were used as representatives of monocots and dicots, respectively, in these studies. The fluorescence spectra of several plant pigments was excited with a nitrogen laser emitting at 337 nm. Intact leaves from corn and soybeans also fluoresced using the nitrogen laser. The two plant species exhibited fluorescence spectra which had three maxima in common at 440, 690, and 740 nm. However, the relative intensities of these maxima were distinctly different for the two species. Soybeans had an additional slight maxima at 525 nm. Potassium deficiency in corn caused an increase in fluorescence at 690 and 740 nm. Simulated water stress in soybeans resulted in increased fluorescence at 440, 525, 690, and 740 nm. The inhibition of photosynthesis in soybeans by 3-(3-4-dichlorophenyl)-1-1-dimethyl urea (DCMU) gave incresed fluorescence primarily at 690 and 740 nm. Chlorosis as occurring in senescent soybean leaves caused a decrease in fluorescence at 690 and 740 nm. These studies indicate that LIF measurements of plants offer the potential for remotely detecting certain types of stress condition and also for differentiating plant species.

Chappelle, E. W.↗

Remote sensing and vegetation stress detection - Problems and progress

Although considerable progress has been made in applying remote sensing technology to vegetation monitoring, considerable problems still exist in the improvement of techniques for crop type discrimination, stress detection on a large scale, and stress quantification. In this paper, some of the problems remaining in the operational use of remote sensing technology for vegetation stress detection are discussed, and directions in which some of these problems might be solved are proposed.

Duggin, M. J.↗

A crack opening stress equation for fatigue crack growth

A general crack opening stress equation is presented which may be used to correlate crack growth rate data for various materials and thicknesses, under constant amplitude loading, once the proper constraint factor has been determined. The constraint factor, alpha, is a constraint on tensile yielding; the material yields when the stress is equal to the product of alpha and sigma. Delta-K (LEFM) is plotted against rate for 2024-T3 aluminum alloy specimens 2.3 mm thick at various stress ratios. Delta-K sub eff was plotted against rate for the same data with alpha = 1.8; the rates correlate well within a factor of two.

Newman, J. C., Jr.↗

Hygrothermal effects on stresses and deformations in a bonded fiber-reinforced plastic/aluminum system

The hygrothermal effect on time dependent mechanical behavior of a model of nonsymmetrical bonded fiber-reinforced plastic (FRP)/aluminum system was investigated analytically. It was found that a linear viscoelastic closed form solution is sufficient for the prediction model deformations for short periods of time and small strains, while a numerical finite-element solution is preferable for determining adhesive stresses and deformational behavior of the model at any time. The thermoelastic numerical solution shows a certain decrease with time of adhesive stresses, which does not seem to affect significantly the global deformations of the model. On the other hand, it was found that the presence of moisture within the polymeric adhesive layer causes significant decrease in adhesive stresses, which affects deformational changes with time, far beyond the level predicted by the static solution.

Yaniv, G.↗

Transient thermal stresses in a reinforced hollow disk or cylinder containing a radial crack

The transient thermal stress problem in a hollow cylinder or a disk containing a radial crack is considered. It is assumed that the cylinder is reinforced on its inner boundary by a membrane which has thermoelastic constants different than those of the base material. The transient temperature, thermal stresses and the crack tip stress intensity factors are calculated in a cylinder which is subjected to a sudden change of temperature on the inside surface. The results are obtained for various dimensionless parameters and material constants. The special cases of the crack terminating at the cylinder-membrane interface and of the broken membrane are separately considered and some examples are given.

Tang, R.↗

Stress-derivative control of keystoning deformation in finite element codes

The stress derivative technique for control of keystoning deformation in under-integrated finte elements is based on expansion of the stress in a Taylor series about the element center and retention of additional terms beyond the constant stress term. It has the advantage over other control techniques that keystoning resistance is provided by actual rather than artificial material properties. Application of this technique to the quadrilateral ring elements used for modelling solids of revolution subjected to axisymmetric loads is described. In a cylindrical coordinate system additional terms appear in the formulation which must be dealt with in arriving at a workable keystoning control scheme.

Schulz, J. C.↗

Nondestructive evaluation of residual stress in low-carbon steel, introduction

The degree of insensitivity of the temperature dependence method to variations in preferred orientations in A508 low carbon steel specimens was determined. A pulsed phase locked loop was used to measure ultrasonic velocity in these specimens in the temperature range of 50 C below and above room temperature. Results are given in tables and indicate that the temperature dependence of ultrasonic longitudinal velocity in four specimens cut at different angles remains unchanged as a function of orientation within + or -2%. The variation of temperature dependence of ultrasonic shear velocity in the A508 steel as a function of applied stresses was also measured. Results show that values at zero stress are equal regardless of whether the polarization direction is parallel or perpendicular to the direction in which the stress is applied.

Source record↗

Stress waves in an isotropic elastic plate excited by a circular transducer

Steady state harmonic stress waves in an isotropic elastic plate excited on one face by a circular transducer are analyzed theoretically. The transmitting transducer transforms an electrical voltage into a uniform normal stress at the top of the plate. To solve the boundary value problem, the radiation into a half-space is considered. The receiving transducer produces an electrical voltage proportional to the average spatially integrated normal stress over its face due to an incident wave. A numerical procedure is given to evaluate the frequency response at a receiving point due to a multiply reflected wave in the near field. Its stability and convergence are discussed. Parameterization plots which determine the particular wave whose frequency response has maximum magnitude compared with other multiple reflected waves are given for a range of values of dimensionless parameters. The effects of changes in the values of the parameters are discussed.

Karagulle, H.↗

Advanced stress analysis methods applicable to turbine engine structures

Advanced stress analysis methods applicable to turbine engine structures are investigated. Constructions of special elements which containing traction-free circular boundaries are investigated. New versions of mixed variational principle and version of hybrid stress elements are formulated. A method is established for suppression of kinematic deformation modes. semiLoof plate and shell elements are constructed by assumed stress hybrid method. An elastic-plastic analysis is conducted by viscoplasticity theory using the mechanical subelement model.

Pian, T. H. H.↗

Characteristics of EMI generated by negative metal-positive dielectric voltage stresses due to spacecraft charging

Charging of spacecraft surfaces by the environmental plasma can result in differential potentials between metallic structure and adjacent dielectric surfaces in which the relative polarity of the voltage stress is either negative dielectric/positive metal or negative metal/positive dielectric. Negative metal/positive dielectric is a stress condition that may arise if relatively large areas of spacecraft surface metals are shadowed from solar UV and/or if the UV intensity is reduced as in the situation in which the spacecraft is entering into or leaving eclipse. The results of experimental studies of negative metal/positive dielectric systems are given. Information is given on: enhanced electron emission I-V curves; e(3) corona noise vs e(3) steady-state current; the localized nature of e(3) and negative metal arc discharge currents; negative metal arc discharges at stress thresholds below 1 kilovolt; negative metal arc discharge characteristics; dependence of blowoff arc discharge current on spacecraft capacitance to space (linear dimension); and damage to second surface mirrors due to negative metal arcs.

Chaky, R. C.↗

Stress and efficiency studies

Optical and electrical characterization of defects has been started in EFG ribbon grown in a system that will be used to test the stress model. Temperature and stress field modeling aimed at defining low stress growth configuration is also in progress, and results will be used to guide development of the experimental system. The baseline defect configuration for ribbon grown at speeds of approx. 1 cm/min consists of dislocation densities of the order of 10 to the 5th power to 10 to the 6th power/sq cm, as well as saucer type etch pits and line defects. All these defects are inhomogeneously distributed. EBIC measurements indicate that diffusion lengths are in the range 20 to 60 microns, and significant spatial inhomogeneities occur through the ribbon thickness. Growth speed changes in the range 0.7-1.0 cm/min do not produce significant variations in ribbon defect configurations.

Source record↗

Mechanical Stress Regulation of Plant Growth and Development

Growth dynamics analysis was used to determine to what extent the seismic stress induced reduction in photosynthetic productivity in shaken soybeans was due to less photosynthetic surface, and to what extent to lower efficiency of assimulation. Seismic stress reduces shoot transpiration rate 17% and 15% during the first and second 45 minute periods following a given treatment. Shaken plants also had a 36% greater leaf water potential 30 minutes after treatment. Continuous measurement of whole plant photosynthetic rate shows that a decline in CO2 fixation began within seconds after the onset of shaking treatment and continued to decline to 16% less than that of controls 20 minutes after shaking, after which gradual recovery of photosynthesis begins. Photosynthetic assimilation recovered completely before the next treatment 5 hours later. The transitory decrease in photosynthetic rate was due entirely to a two fold increase in stomatal resistance to CO2 by the abaxial leaf surface. Mesophyll resistance was not significantly affected by periodic seismic treatment. Temporary stomatal aperture reduction and decreased CO2 fixation are responsible for the lower dry weight of seismic stressed plants growing in a controlled environment.

Mitchell, C. A.↗

A continuous damage model based on stepwise-stress creep rupture tests

A creep damage accumulation model is presented that makes use of the Kachanov damage rate concept with a provision accounting for damage that results from a variable stress history. This is accomplished through the introduction of an additional term in the Kachanov rate equation that is linear in the stress rate. Specification of the material functions and parameters in the model requires two types of constituting a data base: (1) standard constant-stress creep rupture tests, and (2) a sequence of two-step creep rupture tests.

Robinson, D. N.↗

Stress and buckling analysis

An analysis is presented of elastic stress and buckling behavior due to thermal stresses in silicon ribbon. Thermal profiles for reducing stresses and improving flatness in wide ribbon are discussed.

Dillon, O. W., Jr.↗

Stress-intensity factors for circumferential surface cracks in pipes and rods under tension and bending loads

The purpose of this paper is to present stress-intensity factors for a wide range of nearly semi-elliptical surface cracks in pipes and rods. The configurations were subjected to either remote tension or bending loads. For pipes, the ratio of crack depth to crack length (a/c) ranged from 0.6 to 1; the ratio of crack depth to wall thickness (a/t) ranged from 0.2 to 0.8; and the ratio of internal radius to wall thickness (R/t) ranged from 1 to 10. For rods, the ratio of crack depth to crack length also ranged from 0.6 to 1; and the ratio of crack depth to rod diameter (a/D) ranged from 0.05 to 0.35. These particular crack configurations were chosen to cover the range of crack shapes (a/c) that have been observed in experiments conducted on pipes and rods under tension and bending fatigue loads. The stress-intensity factors were calculated by a three-dimensional finite-element method. The finite-element models employed singularity elements along the crack front and linear-strain elements elsewhere. The models had about 6500 degrees of freedom. The stress-intensity factors were evaluated using a nodal-force method.

Raju, I. S.↗

Hybrid stress finite elements for large deformations of inelastic solids

A new hybrid stress finite element algorithm, based on a generalization of Fraeijs de Veubeke's complementary energy principle is presented. Analyses of large quasistatic deformation of inelastic solids (hypoelastic, plastic, viscoplastic) are within its capability. Principle variables in the formulation are the nominal stress rate and spin. A brief account is given of the boundary value problem in these variables, and the 'equivalent' variational principle. The finite element equation, along with initial positions and stresses, comprise an initial value problem. Factors affecting the choice of time integration schemes are discussed. Results found by application of the new algorithm are compared to those obtained by a velocity based finite element algorithm.

Reed, K. W.↗

Stress-corrosion behavior of aluminum-lithium alloys in aqueous salt environments

The stress corrosion susceptibility of two powder metallurgy (P/M) alloys, Al-Li-Cu and Al-Li-Cu-Mg; two mechanically attrited (M/A) alloys, Al-Li-Cu and Al-Li-Mg; and two wrought, ingot alloys, X-2020 and AA7475, are compared. Time-dependent fracture in an aqueous sodium chloride environment under alternate immersion condition was found to vary significantly between alloys. The stress corrosion behavior of the two powder metallurgy processed alloys was studied in detail under conditions of crack initiation, static crack growth, and fatigue crack growth. A variety of stress corrosion tests were performed including smooth surface, time-to-failure tests; potentiostatic tests on smooth surfaces exposed to constant applied strain rates; and fracture mechanics-type tests under static and cyclic loads. Both alloys show surface pitting and subsequent intergranular corrosion. Pitting is more severe in the magnesium-bearing alloy and is associated with stringer particles strung along the extrusion direction as a result of P/M processing.

Pizzo, P. P.↗

Stress analysis method for a clearance fit bolt under bearing loads

In the present, simple analysis method for bolt hole clearance stresses in mechanically fastened joints, an inverse formulation is used with a finite element analysis. Conditions along the bolt hole contact arc are specified by displacement constraint equations. The method was applied to a single fastener clearance-fit joint with typical clearance values, for the cases of a rigid, frictionless bolt and a quasi-isotropic graphite/epoxy laminate. Results indicate that the contact arc, as well as the peak stresses around the hole (and their locations), were strongly influenced by the clearance. After a minor initial nonlinearity, peak stresses varied linearly with applied load. Clearance levels are found to have only a minor influence on overall joint stiffness.

Crews, J. H., Jr.↗