Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROLLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Universal Mechanism of Viscoplastic Deformation of Metallic Materials Far from Thermodynamics Equilibrium

The article gives results of structure formation in metallic materials after different types of deformation: tungsten after rolling, nickel after thermal cycling and nickel single crystal after rolling, aluminum single crystal after cyclic tension and aluminum alloys (D16, 2024-T3) after impulsive load. We used optical and electron microscopy methods for investigation of deformation structure formation and molecular dynamics method for computer modeling of the processes of plastic deformation (LAMMPS software). The following quantitative parameters were calculated during the simulation: energy of pair interaction, temperature, total cumulative pressure, stress tensor and pressure tensor. The study shows that the plastic flow of metallic materials with any initial structure at certain loading stage can be carried out by homogeneous mass transfer through channels with a liquid-like structure, from which follows that the dislocation mechanism of plastic deformation of crystals has a limited field of application. The main role has a synergistic structure formation in the conditions of distance from thermodynamic equilibrium. The relaxation processes proceed intensively after and during the process of destruction. The results of modeling have shown the possibility of forming channels of hydrodynamic flow without the participation of defects in the initial material.

36 MATERIALS SCIENCE↗

Microstructure and Deformation Mechanism of AZ31 Magnesium Alloy Under Dynamic Strain Rate

A hot-rolled AZ31Mg alloy sheet was subjected to dynamic plastic deformation parallel to the rolling direction, and microstructural evolutions and mechanical properties of the deformed samples were examined. It has been found that dynamic strain rate could facilitate {10-12} twin nucleation and growth and leads to a lower yield stress of about 20 MPa and an early end to twinning characteristic (happening at a strain point of about 6%) shown in the stress–strain curve. {10-12} twinning mechanism dominates the early plastic deformation; but when plastic strain exceeds ~ 9%, dislocation–slip mechanism instead of {10-12} twinning dominates the later plastic deformation. And this premature transformation of the dominant deformation mechanisms from {10-12} twinning to dislocation slip is caused by dynamic strain rate. The effect of dynamic strain rate on the number of twin nucleations remains unclear, and the more systematic researches are needed in the future.

36 MATERIALS SCIENCE↗

Effect of Minor Er on the Microstructure and Properties of Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr Alloys

As-cast Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr alloys containing different additions of Er were prepared. Then, the specimens were carried out homogenization heat treatment, hot rolling, cold rolling, and annealing. The effects of minor Er on the microstructure and properties of Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr alloy were investigated. Results show that addition of Er can refine the microstructure and improve the mechanical properties of the alloys. As for the annealed alloys, the addition of 0.33%Er can increase the tensile strength by 29 MPa. Strength increment is mainly attributed to refinement and the precipitation of Al{sub 3}Er and Al{sub 3}(Er, Zr). Additionally, the minor Er can improve the corrosion resistance of the alloys, which can be attributed to the compact composite oxide film of Er-O and Al-O, purification, and modification.

36 MATERIALS SCIENCE↗

Effect of Orientation of Weld Line on Formability of Electron Beam-Welded Dissimilar Thickness Titanium Sheets

Recently, manufacturing industries are looking forward to get insight into the influence of weld orientation on formability of tailor-welded blanks (TWBs) of titanium sheets for design and fabrication of lightweight components. Hence, commercially pure titanium (CP Ti) sheets of 1.0 and 1.2 mm thickness were joined together by electron beam welding process using accelerating voltage of 55 kV, beam current of 14.9 mA and welding speed of 865 mm/min. Two different types of TWBs with weld line perpendicular to the rolling direction (WL ⊥ RD) and weld line parallel to the rolling direction (WL || RD) were fabricated, and subsequently, the tensile test, microstructure and microhardness characterizations were conducted to ensure quality of weld. The limiting dome height (LDH) tests were carried out using laboratory-scale setup to evaluate forming behavior of both the above TWBs in terms of FLD, strain distribution, weld line movement and failure location. It was found that the tensile stress–strain response and formability performance of TWBs were significantly influenced by weld line orientation with lower ductility, ultimate tensile strength and LDH in TWB of WL || RD. Moreover, significant weld line movement and non-uniform strain distribution with necking and subsequently fracture were observed away from the weld line in thinner 1.0 mm CP Ti sheets depending on both sample geometry and weld line orientation.

36 MATERIALS SCIENCE↗

Mapping of crack tip strains and twinned zone in a hexagonal close packed zirconium alloy.

This paper describes the use of synchrotron X-ray diffraction to map crack tip strain field evolution and initiation of twinning under applied load in a fatigue pre-cracked zirconium alloy. Compact tension specimens were machined in two orientations from a textured rolled plate and loaded along the normal direction and the transverse direction to rolling. Residual strains due to fatigue and the strains introduced at applied K, of approximately 10 and 30 MPa{radical}m were measured for the two specimen orientations. Maps of the region of twinned material were determined. The experimental data is compared to finite element (FE) calculations for the crack tip strain fields and a prediction of the size of the twinned region using a multiscale model based on combining an FE approach with an elastoplastic self-consistent polycrystalline plasticity model.

36 MATERIALS SCIENCE↗

Reverse martensitic transformation on the corrosion behavior of a 2304 lean duplex stainless steel

This study investigates the influence of the reverse martensitic transformation on the corrosion behavior of 2304 lean duplex stainless steel (LDSS) at low temperatures (400–600°C). The steel underwent cold rolling, followed by isochronal annealing for 0.5 h. Phase transformations and microstructures were analyzed using X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Corrosion resistance was evaluated using a syringe cell with cyclic potentiodynamic polarization in 0.6 M NaCl solution and double-loop electrochemical potentiokinetic reactivation in 0.5 M H 2 SO 4 + 0.001 M KSCN solution. A bimodal breakdown potential behavior, associated with either pitting or transpassivity, was observed in the as-received (AR) and samples annealed at 400°C. Pitting in the AR sample was associated with Al–Mg–Si–Ca–O inclusions, while pitting on the samples annealed at 400°C was linked to local reduced passive film resistance. Severe cold rolling enhanced the pitting resistance of 2304 LDSS. Selective electrochemical etching revealed preferential corrosion at phase interfaces and within the austenite phase. Additionally, annealing at 500°C to 600°C led to a marked decrease in pitting resistance and increased sensitization. Electron backscatter diffraction analysis of the corroded pits in the annealed specimens indicated that pits tend to nucleate and grow in α'-martensite/austenite regions. Furthermore, the nanostructure formed during low-temperature reversion, characterized by dislocation-cell martensite with high dislocation density and stacking faults, may adversely affect corrosion resistance due to heterogeneities associated with alloying element redistribution.

36 MATERIALS SCIENCE↗

A critical review of the history of fabricating monolithic U-Mo fuel plates

The fabrication of monolithic uranium-molybdenum alloy fuels, specifically those developed for high-performance research and test reactors, began in the early 2000s. The primary fuel form consists of uranium alloyed with 10-wt% molybdenum in a thin foil coated with zirconium and encapsulated in aluminum-6061 cladding. Over the years, the process has evolved with different types of casting, heat treatments, rolling schedules, and cladding applications. This review examines the history of these fabrication processes and their impact on microstructure and fuel-swelling performance. Even though various fabrication methods were used, we found little correlation between fabrication variation and fuel swelling. This insensitive relationship between fabrication variation and fuel swelling is primarily due to inhomogeneous microstructures that formed during casting and grain refinement that occurred during rolling. We conclude that the fabrication processes we examined produced similar microstructures, indicating that the fuel microstructure is somewhat insensitive to the fabrication parameters evaluated. However, the relatively small amount of historic data, such as those for grain sizes, limited this analysis. More recently fabricated materials, such as those from ongoing irradiation experiment, Mini-Plate-1 and Mini-Plate-2, were also excluded from this analysis and are intended to be reviewed separately. The findings, that fuel microstructure is somewhat insensitive to the fabrication parameters, do not imply that any fabrication method is acceptable, given the uncertainties in data and fuel-swelling observations. For example, only arc melting and vacuum induction melting casting processes were previously explored in the historic fabrication efforts. In conclusion, the findings should not be extrapolated to other casting processes.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural and mechanical behavior of highly deformed Al-Sn alloys

Tensile strength and microstructural evolution were evaluated for the deformation processed metal-metal composites of Al-X vol.% Sn, where X = 3.96, 16.32, 20. Samples were prepared by casting, and deformed by cold rolling. The material was characterized by scanning electron microscopy and focused ion beam. In the case of larger true strains {eta} > 5, the composite presents an unexpected increase in tensile strength compared to the rule of mixtures. During cold rolling, the Sn phase developed a lamellar morphology and geometrical aspects, as its separation and thickness were correlated with the tensile strength of the composite. A study of the peak broadening was made by using X-ray diffraction, in order to measure the microstrains inside the composite, and correlate them with the macroscopic strength.

36 MATERIALS SCIENCE↗

Effect of martensite to austenite reversion on the formation of nano/submicron grained AISI 301 stainless steel

The martensite to austenite reversion behavior of 90% cold rolled AISI 301 stainless steel was investigated in order to refine the grain size. Cold rolled specimens were annealed at 600-900 deg. C, and subsequently characterized by scanning electron microscopy, X-ray diffraction, Feritscope, and hardness measurements. The effects of annealing parameters on the formation of fully-austenitic nano/submicron grained structure and the mechanisms involved were studied. It was found that annealing at 800 deg. C for 10 s exhibited the smallest average austenite grain size of 240 {+-} 60 nm with an almost fully-austenitic structure.

36 MATERIALS SCIENCE↗

Texture evolution in Fe-3% Si steel treated under unconventional annealing conditions

The present work investigates texture evolution stages in grain-oriented steel heat-treated using unconventional conditions. The Fe-3%Si steel taken after final cold rolling reduction from an industrial line was subjected to a laboratory isothermal annealing at different temperatures. The annealing temperatures were varied in a range of 850-1150 deg. C. During the annealing each specimen was heated at 10 deg. C/s and kept at the stated temperature for 5 min. Development of microstructure and texture in the annealed specimens were followed by the DC measurements of magnetic properties. The grain oriented steel, taken from the same industrial line after final box annealing was also analyzed and compared with the laboratory annealed specimens. It was shown that there is an optimal temperature region that, with combination of a fast heating rate, led to the best conditions of a drastically reduced development time of the {l_brace}110{r_brace} < 001 > crystallographic texture in the cold rolled grain-oriented steel. Materials heat treated below the optimum temperature region account for a primary recrystallization, while applying heat above this region leads to a secondary recrystallization without abnormal grain growth. Moreover, in the optimum temperature range, there was a particular temperature leading to the most optimal microstructure and texture. The magnetic properties, measured after the optimal heat treatment, were close to that measured on specimens taken after the final box annealing. The electron back scattered diffraction measurement technique revealed that sharpness of the {l_brace}110{r_brace} < 001 > crystallographic texture, developed at the optimum temperature is comparable to the steel taken after the industrial final box annealing. This fact is evidence that there is a temperature where the abnormal grain growth proceeds optimally.

36 MATERIALS SCIENCE↗

Aging behavior and mechanical properties of maraging steels in the presence of submicrocrystalline Laves phase particles

Cold rolling and annealing of homogenized Fe-Ni-Mn-Mo-Ti-Cr maraging steels resulted in the formation of submicrocrystalline Fe{sub 2}(Mo,Ti) Laves phase particles. Optical and scanning electron microscopy, X-ray diffraction, tensile and hardness tests were used to study the microstructure, aging behavior and mechanical properties of the annealed steels. The annealed microstructures showed age hardenability during subsequent isothermal aging at 753 K. Ultrahigh fracture stress but poor tensile ductility was obtained after substantial age hardening in the specimens with 2% and 4% chromium. Increasing chromium addition up to 6% toughened the aged microstructure at the expense of the fracture stress by increasing the volume fraction of retained austenite. The Laves phase particles acted as crack nucleation sites during tensile deformation. - Highlights: {yields} Laves phases dispersed in a BCC iron matrix by annealing of cold rolled samples. {yields} The samples showed age hardenability during subsequent isothermal aging at 753 K. {yields} Ultrahigh fracture stress but poor ductility was obtained after age hardening. {yields} Increasing chromium addition toughened the aged microstructure. {yields} Laves phase particles acting as crack nucleation sites during tensile deformation.

36 MATERIALS SCIENCE↗

Microstructure evolution of 7050 Al alloy during age-forming

The microstructure evolution of the 7050 Al alloy treated by age-forming was studied using a designed device which can simulate the age-forming process. The grain shape, grain boundary misorientation and grain orientation evolution of 7050 Al alloy during age-forming have been quantitatively characterized by electron backscattering diffraction technique. The results show that age-forming produced abundant low-angle boundaries and elongated grains, which attributed to stress induced dislocation movement and grain boundary migration during the age-forming process. On the other side, the stress along rolling direction caused some unstable orientation grains to rotate towards the Brass and S orientations during the age-forming process. Hence, the intensity of the rolling texture orientation in age-formed samples is enhanced. But this effect decays gradually with increasing aging time, since stress decreases and precipitation hardening occurs during the age-forming process. - Highlights: • Quantitative analysis of grain evolution of 7050 Al alloys during age-forming • Stress induces some grain rotation of 7050 Al alloys during age-forming. • Creep leads to elongate grain of 7050 Al alloys during age-forming. • Obtains a trend on texture evolution during age-forming applied stress.

36 MATERIALS SCIENCE↗

Comparative study of structure formation and mechanical behavior of age-hardened Ti–Nb–Zr and Ti–Nb–Ta shape memory alloys

This work sets out to study the peculiar effects of aging treatment on the structure and mechanical behavior of cold-rolled and annealed biomedical Ti–21.8Nb–6.0Zr (TNZ) and Ti–19.7Nb–5.8Ta (TNT) (at.%) shape memory alloys by means of transmission electron microscopy, X-ray diffractometry, functional fatigue and thermomechanical testing techniques. Dissimilar effects of aging treatment on the mechanical behavior of Zr- and Ta-doped alloys are explained by the differences in the ω-phase formation rate, precipitate size, fraction and distribution, and by their effect on the alloys' critical stresses and transformation temperatures. Even short-time aging of the TNZ alloy leads to its drastic embrittlement caused by “overaging”. On the contrary, during aging of the TNT alloy, formation of finely dispersed ω-phase precipitates is gradual and controllable, which makes it possible to finely adjust the TNT alloy functional properties using precipitation hardening mechanisms. To create in this alloy nanosubgrained dislocation substructure containing highly-dispersed coherent nanosized ω-phase precipitates, the following optimum thermomechanical treatment is recommended: cold rolling (true strain 0.37), followed by post-deformation annealing (600 °C, 15–30 min) and age-hardening (300 °C, 30 min) thermal treatments. It is shown that in TNT alloy, pre-transition diffraction effects (diffuse reflections) can “mask” the β-phase substructure and morphology of secondary phases. - Highlights: • TNZ alloy is characterized by much higher ω-phase precipitation rate than TNT alloy. • Difference in precipitation rates is linked to the difference in Zr and Ta diffusion mobility. • Aging of nanosubgrained TNZ alloy worsens its properties irrespective of the aging time. • Aging time of nanosubgrained TNT alloy can be optimized to improve its properties.

36 MATERIALS SCIENCE↗

Microstructure development and texture evolution of aluminum multi-port extrusion tube during the porthole die extrusion

Aluminum multi-port extrusion tube is processed by the porthole die extrusion and the internal tube walls are welded through the solid state metallurgical bonding. In order to observe the development of grains and their orientations under severe plastic deformation and solid state welding, the extrusion butt together with the die is quenched immediately after extrusion to preserve the grain structure in the processing. The forming histories of selected material points are obtained by analyzing the optical microscopy graph. The evolution of the microstructure along the forming path is characterized by electro backscattered diffraction. It is found that geometrical dynamic recrystallization happens in the process. Grains are elongated, scattered at the transition zone and shear intensive zone, and then pinched off when they are pushed out from the die orifice. The shear-type orientations are predominant at the surface layer on the longitudinal section of the tube web and have penetrated into the intermediate layer. The rolling-type orientations are formed at the central layer. Texture gradient through the thickness of the tube web is observed. And cube orientated grains are found at the seam weld region. - Highlights: •Microstructure of extrusion butt is preserved after the micro scale porthole die extrusion. •Grain morphology history along forming path is investigated. •Texture evolutions on three material flows are present. •Texture gradient exists on the longitudinal section of the internal wall of profile. •Rolling-type and cube textures are found at the solid state welding region.

36 MATERIALS SCIENCE↗

Three-dimensional (3D) analysis of white etching bands (WEBs) in AISI M50 bearing steel using automated serial sectioning

Dark etching regions (DER) and white etching bands (WEB) form in the subsurface stressed regions of bearing raceways and rolling elements. Also, “butterfly” formations form around non-metallic inclusions and large carbides. The formation of WEBs, DERs and butterfly are dependent on operating conditions, material alloying elements and heat treatment. The DER, WEB and butterfly formations are well studied in two dimensions (2D). The objective of this study was to analyze WEB formation in three dimensions (3D) that will allow better understanding of material transformation after stress cycling. Three rolling contact fatigue (RCF) tested vacuum induction melted vacuum arc re-melted (VIM-VAR) AISI M50 samples (from a bench test, sub-scale test and commercial gas turbine engine) were analyzed using automated serial sectioning to map WEB networks and a butterfly formation in 3D. Automated serial sectioning and 2D optical microstructural data for 3D reconstructions and analysis was done using a fully automated serial sectioning system – Robo-Met.3D®. 3D analysis was performed using Image-Pro Premier 3D. The data set allowed 3D visualization and analysis of the evolution and propagation of WEB and butterfly in M50 bearing steel, including the positive microscopic identification of a ceramic inclusion that was the source of a WEB.

36 MATERIALS SCIENCE↗

An algorithm for automatic identification of double twin variants in Mg alloys

Highlights: • An algorithm for automatic identification of {10–11}–{10–12} double twin variants is proposed. • This algorithm is applicable for the cases without knowing the primary twin orientations. • The primary twin orientations can be reconstructed using this algorithm. - Abstract: {10 1-bar 1}−{10 1-bar 2} double twins (DTs) are profuse in Mg alloys after rolling at a large reduction (>10%). In many cases, the secondary twins completely occupy the primary ones, causing difficulty in variant analysis. Here, we propose an algorithm for automatic identification of twin variants. This is applicable for the {10 1-bar 1}−{10 1-bar 2} DTs without knowing the primary twins. In addition, two kinds of stereographic projections are constructed to assist such variant selection. By this method, the variants of 67 DTs observed in a rolled AZ31 sheet are determined. Based on 14 sets of DTs with known primary twin orientations, the high efficiency and reliability of this proposed algorithm is verified. The reason for unreliable variant identification in two special cases is also discussed.

36 MATERIALS SCIENCE↗

Integrated charging infrastructure planning and charging scheduling for battery electric bus systems

We report studies on the electric bus system planning problem have typically focused exclusively on either the deployment of charging infrastructure or the scheduling of charging events; few have examined the impact of charging facility deployment on charging activities. Considering the interdependence of system design and operational strategies, this study proposes a two-phase optimization framework for charging infrastructure planning and charging scheduling for battery electric bus systems. An integrated optimization model is first developed to simultaneously optimize charger deployment, on-board battery capacity, and charging schedules. A charging scheduling model is further proposed and a rolling horizon approach is utilized in the second phase to optimize the real-time charging scheduling of electric buses. Compared to existing electric bus system planning methods, the proposed integrated model can reduce the total system cost by 19.5%. In addition, compared to uncontrolled charging, the proposed rolling horizon-based charging strategy can reduce the total charging cost by 68.3%.

25 ENERGY STORAGE↗

Friction behavior of a multi-interface system and improved performance by AlMgB 14 –TiB 2 –C and diamond-like-carbon coatings

We investigated friction behavior of a bearing system with two interfaces involved: a roller component experiencing rolling–sliding interaction against twin cylinders under point contacts while simultaneously undergoing pure sliding interaction against a socket under a conformal contact. Lubrication modeling predicted a strong correlation between the roller's rolling condition and the system's friction behavior. Experimental observations first validated the analytical predictions using steel and iron components. Diamond-like-carbon (DLC) coating and AlMgB 14 –TiB 2 coating with a carbon topcoat (BAMC) were then applied to the roller and twin cylinders, respectively. In conclusion, testing and analysis results suggest that the coatings effectively decreased the slip ratio for the roller–cylinder contact and the sliding friction at both bearing interfaces and, as a result, significantly reduced the system frictional torque.

42 ENGINEERING↗