Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REFLECTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Improvement of Front-Junction GaInP by Point-Defect Injection and Annealing

Traditional front junction GaInP solar cells are radiation tolerant and can have good diffusion length, but have limited voltage and thus efficiency. Here, we investigate the impact of annealing on GaInP device performance. First, Zn-doped GaInP/AlGaInP double heterojunction structures are studied in order to investigate the impact of annealing in a simple structure. While standard anneals lower diffusion length and lifetime, annealing after injecting point-defects improves material quality, presumably by eliminating sources of non-radiative recombination. Atomic ordering is reduced by the anneal, which raises the device bandgap and requires consideration. These results can be used to improve front junction device performance while controlling the bandgap. Then, GaInP front-junction devices are created using anneals with and without point-defect injection. Voc and EQE trends follow the diffusion length and lifetime trends from the DH structures. Baseline devices have Woc of 0.484 V, raising to 0.504 V after a high temperature anneal. However, injecting point defects prior to the anneal results in a front junction device with Woc of 0.405 V and a diffusion length greater than 8 micrometers. Optimized front-junction GaInP devices with an ARC have ~20% efficiency without a rear reflector.

anneal↗

High Flux Isotope Reactor Neutron Spectrum Shape Estimation From Activation Experiment Data

Here, this article provides a comprehensive review of historical irradiation dosimetry available for different locations within the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). This article includes a summary of the available measured activation target data covering a span of over 15 years and 39 experimental campaigns, including 200 individual sample locations evaluated. Using this broad set of data, we reconstruct historic average neutron spectra shapes for HFIR at various locations, including within the flux trap region, beryllium reflectors, and hydraulic tube (HT) regions, at both the 100- and 85-MW operational power. Our findings indicate that the general axial flux distribution shows a relatively small change in transition from 100- to 85-MW operating power, with differences of -6% to +15% for the thermal energy range and around -16% to +8% for the fast range, indicating a sharper drop-off of the thermal neutron flux away from the axial center. Compared with historical dosimetry estimates of the HFIR flux shape, we generally find a moderately broader axial profile shape for thermal neutrons in the interior target regions for the 100-MW samples evaluated but relatively close agreement for the present 85-MW flux shape for both thermal and fast fluxes.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Langasite Surface Acoustic Wave Sensors: Fabrication and Testing

We report on the development of harsh-environment surface acoustic wave sensors for wired and wireless operation. Surface acoustic wave devices with an interdigitated transducer emitter and multiple reflectors were fabricated on langasite substrates. Both wired and wireless temperature sensing was demonstrated using radar-mode (pulse) detection. Temperature resolution of better than ±0.5°C was achieved between 200°C and 600°C. Oxygen sensing was achieved by depositing a layer of ZnO on the propagation path. Although the ZnO layer caused additional attenuation of the surface wave, oxygen sensing was accomplished at temperatures up to 700°C. The results indicate that langasite SAW devices are a potential solution for harsh-environment gas and temperature sensing.

47 OTHER INSTRUMENTATION↗

Evaluation of Composite Structural Materials for Heliostat Cost Reduction

Structures manufactured from steel comprise up to 40% of a CSP heliostat's cost. Composite structures represent a potential opportunity to reduce this cost. A reference heliostat structural model has been created with a reflector area of 25m 2 . The design, constructed of low-carbon steel, pro-vides baseline deflection and stiffness under a 21 m/s operating wind speeds. Wind loads on the tracker structure are determined for both operating and stow conditions. An established roster of suitable metal alternative materials is considered including: glass, basalt, and carbon reinforced polymer (GFRP, BFRP, and CFRP respectively). Three heliostat components are investigated: the pylon, torque tube, and the purlin-strut assembly. Composite material properties are substituted for those of steel, and the beams are re-sized to match the original steel components' deflection under given wind loads. Weight and cost changes resulting from this resizing are evaluated. It is found that GFRP and BFRP represent a 3X–6X cost premium for the same operating deflection character-istics as steel across all three investigated component classes; with weight reduction only achieved for the purlin-strut assembly. While CFRP components can achieve approximately 25–75% weight savings depending on the application, this comes with a 9X–14X cost increase over the steel base-line for tube-type structures and roughly 5X cost increase when replacing c-channel structures. This work does not rule out the possibility of cost savings when the heliostat design and kinematics to take advantage of composites' specific properties.

14 SOLAR ENERGY↗

Modeling Microwave-Enhanced Chemical Vapor Infiltration Process for Preventing Premature Pore Closure

The chemical vapor infiltration (CVI) process involves infiltrating a porous preform with reacting gases that undergo chemical transformation at high temperatures to deposit the ceramic phase within the pores, ultimately leading to a dense composite. The conventional CVI process in composite manufacturing needs to follow an isothermal approach to minimize temperature differences between the external and internal surfaces of the preform, ensuring that reactive gases infiltrate internal pores before external surfaces seal. Here, this study addresses the challenge of premature pore closure in CVI processes through microwave heating. A frequency-domain microwave solver is developed in OpenFOAM to investigate volumetric heating mechanisms within the preform. Through numerical studies, we demonstrate the capability of microwave heating of creating an inside-out temperature inversion. This inversion accelerates reactions proximal to the preform center, effectively mitigating the risk of premature external pore closure and ensuring uniform densification. The results reveal a significant enhancement in temperature inversion when high-permittivity reflectors are incorporated to generate resonant waves. This microwave heating strategy is then coupled with high-fidelity direct numerical simulation (DNS) of reacting flow, enabling the analysis of resulting densification processes. The DNS includes detailed chemistry and realistic diffusion coefficients. The numerical results can be used to estimate the impact of microwave-induced temperature inversion on densification in productions.

42 ENGINEERING↗

Absorber Alignment Measurement Tool for Solar Parabolic Trough Collectors: Preprint

As we pursue efforts to lower the capital and installation costs of parabolic trough solar collectors, it is essential to maintain high optical performance. While there are many optical tools available to measure the reflector slope errors of parabolic trough solar collectors, there are few tools to measure the absorber alignment. A new method is presented here to measure the absorber alignmentin two dimensions to within 0.5 cm. The absorber alignment is measured using a digital camera and four photogrammetric targets. Physical contact with the receiver absorber or glass is not necessary. The alignment of the absorber is measured along its full length so that sagging of the absorber can be quantified with this technique. The resulting absorber alignment measurement provides criticalinformation required to accurately determine the intercept factor of a collector.

14 SOLAR ENERGY↗

Modeling Microwave-Enhanced Chemical Vapor Infiltration Process for Preventing Premature Pore Closure

The chemical vapor infiltration (CVI) process involves infiltrating a porous preform with reacting gases that undergo chemical transformation at high temperatures to deposit the ceramic phase within the pores, ultimately leading to a dense composite. The conventional CVI process in composite manufacturing needs to follow an isothermal approach to minimize temperature differences between the external and internal surfaces of the preform, ensuring that reactive gases infiltrate internal pores before external surfaces seal. This study addresses the challenge of premature pore closure in CVI processes through microwave heating. A frequency-domain microwave solver is developed in Open-FOAM to investigate volumetric heating mechanisms within the preform. Through numerical studies, we demonstrate the capability of microwave heating of creating an inside-out temperature inversion. This inversion accelerates reactions proximal to the preform center, effectively mitigating the risk of premature external pore closure and ensuring uniform densification. The results reveal a significant enhancement in temperature inversion when high-permittivity reflectors are incorporated to generate resonant waves. This microwave heating strategy is then coupled with high-fidelity direct numerical simulation (DNS) of reacting flow, enabling the analysis of resulting densification processes. The DNS simulation includes detailed chemistry and realistic diffusion coefficients. The numerical results can be used to estimate the impact of microwave-induced temperature inversion on densification in productions.

Ge, Wenjun↗

Preliminary waste management plan of European spallation

The European Spallation Source (ESS) is the European common effort in designing and building a next generation large-scale user facility for studies of the structure and dynamics of materials. The proposed schematic layout of the ESS facility is based on a linear driver (linac) directing the proton beam (5 MW of 2.5 GeV) of 2.8 ms long pulses with a 20 Hz on a tungsten target where neutrons are produced via spallation reactions. Further the neutrons will be moderated to thermal and sub-thermal energies in a couple of moderators placed around the target. The moderators feed 22 beamlines guiding the neutrons to the scattering instruments, mainly for neutron scattering research, as has been previously mentioned. The objective of this work is to develop a waste management plan for ESS facility. In this respect two important aspects are analyzed. First the present status of the problem is outlined as follow. Estimate types and quantities of waste that the ESS project will generate at different stages: commission, operation, decommissioning were derived using: i) precise Monte Carlo calculations ii) scaling the activity from the operation experience of the existing spallation source installations for waste such it is difficult to predict level of activation or for components of the facility in stage of the preconceptual model. Associated waste treatment/conditioning options and final disposal route were further analyzed in order to define the waste type and packet descriptions in agreement with Swedish regulations and policy. It was found that the compilation of completely new waste type descriptions for qualification of the ESS waste for disposal will be necessary. Particular attention was devoted to 'problematic waste' as Beryllium reflector, C-14 from graphite used as core zone of the beam-dump and collimators or waste arising from the purification systems of both Helium and water cooling circuits. Management of waste on ESS site: collection/segregation systems, characterization system, storage options, is also described. In the second step, the acquired information is used for planning and implementing actions involving all participants (ESS, treatment facility operator, disposal operator, regulatory body and other authorized authorities). (authors)

07 ISOTOPE AND RADIATION SOURCES↗

UNDERSTANDING THE SEMI-PROBABILISTIC APPROACHES IN STRUCTURAL RELIABILITY USED TO SET DESIGN RELIABILITY TARGETS FOR GRAPHITE COMPONENTS USING ASME BPVC METHODS

Graphite is a quasi-brittle material, resulting in random variability in tensile strength distributions. To account for the random variability in strength, HHA-3000 of the ASME BPVC provides two semi-probabilistic methods for qualifying nuclear graphite components in the design stage, the simplified and full assessments. The full and simplified assessments apply statistical methods to engineering-based design problems. This is often referred to as reliability-based design. Reliability-based design (RBD) is a method to develop reliable designs by accounting for uncertainties and result in small chances of failure when also considering safety factors. RBDs provide reliability targets using semi-probabilistic approaches. RBD is implemented in ASME BPVC HHA-3000 for nuclear graphite components, but is not specific to that application. There has been much confusion around the methods implemented in ASME BPVC HHA-3000 for qualifying nuclear graphite components. To address the confusion, this paper takes a hierarchical approach. First, the general RBD framework is presented. Then, the semi-probabilistic methods and the underlying assumptions implemented in the assessments are presented. The semi-probabilistic methods are separated from the engineering modifications that have been made to the assessments. After building the framework and underlying assumptions, the specific methods in the full and simplified assessments are explained in three steps: inputs, methods, outputs. The methods are applied to an H-451 reflector block. Tensile strength properties for other graphite grades are provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Spatial scaling metrics of mask-induced induced line-edge roughness

Mask contributors to line-edge roughness (LER) have recently been shown to be an issue of concern for both the accuracy of current resist evaluation tests as well the ultimate LER requirements for the 22-nm production node. Problems arise from mask absorber LER as well as mask reflector or surface roughness leading to random phase variations in the reflected beam. Not only do these mask contributors effect to total measured LER in resist, but they also effect LER spatial characteristic such as the LER power spectral density and related descriptors of correlation length and roughness exponent. Noting that these characteristics are important in the understanding of LER, it is crucial to understand how mask effects impact these parameters. Moreover, understanding how these metrics respond to mask effects may lead to an experimental mechanism for experimentally evaluating the importance of mask contributors to LER. Here we use computer modeling to study the LER spatial metrics arising from mask effects. We further describe the effects of illumination conditions and defocus on the metrics and compare the results to those expected from intrinsic resist LER.

36 MATERIALS SCIENCE↗

Deposition and characterization of Cd{sub 1−x}Mg{sub x}Te thin films grown by a novel cosublimation method

Photovoltaic cells utilizing the CdS/CdTe structure have improved substantially in the past few years. Despite the recent advances, the efficiency of CdS/CdTe cells is still significantly below their Shockley–Queisser limit. CdTe based ternary alloy thin films, such as Cd{sub 1−x}Mg{sub x}Te (CMT), could be used to improve efficiency of CdS/CdTe photovoltaic cells. Higher band gap Cd{sub 1−x}Mg{sub x}Te films can be the absorber in top cells of a tandem structure or an electron reflector layer in CdS/CdTe cells. A novel cosublimation method to deposit CMT thin films has been developed. This method can deposit CMT films of band gaps ranging from 1.5 to 2.3 eV. The cosublimation method is fast, repeatable, and scalable for large areas, making it suitable for implementing into large-scale manufacturing. Characterization of as-deposited CMT films, with x varying from 0 to 0.35, reveals a linear relationship between Mg content measured by energy dispersive x-ray spectroscopy and the optical band gap. Glancing angle x-ray diffraction (GAXRD) measurements of Cd{sub 1−x}Mg{sub x}Te films show a zinc-blende structure similar to CdTe. Furthermore, increasing Mg content decreases the lattice parameter and the grain size. GAXRD shows the films are under mild tension after deposition.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Heterovalent semiconductor structures and devices grown by molecular beam epitaxy

Heterovalent structures consisting of group II-VI/group III-V compound semiconductors offer attractive properties, such as a very broad range of bandgaps, large conduction band offsets, high electron and hole mobilities, and quantum-material properties such as electric-field-induced topological insulator states. These properties and characteristics are highly desirable for many electronic and optoelectronic devices as well as potential condensed-matter quantum-physics applications. Here, we provide an overview of our recent studies of the MBE growth and characterization of zincblende II-VI/III-V heterostructures as well as several novel device applications based on different sets of these materials. By combining materials with small lattice mismatch, such as ZnTe/GaSb (Δa/a~0.13%), CdTe/InSb (Δa/a~0.05%), and ZnSe/GaAs (Δa/a~0.26%), epitaxial films of excellent crystallinity were grown once the growth conditions had been optimized. Cross-sectional observations using conventional and atomic-resolution electron microscopy revealed coherent interfaces and close to defect-free heterostructures. Measurements across CdTe/InSb interfaces indicated a limited amount (~1.5 nm) of chemical intermixing. Results for ZnTe/GaSb distributed Bragg reflectors, CdTe/Mg x Cd 1-x Te double heterostructures, and CdTe/InSb two-color photodetectors are briefly presented, and the growth of a rock salt/zincblende PbTe/CdTe/InSb heterostructure is also described.

Materials Science↗

Boulder damage symposium annual thin film laser damage competition

Optical instruments and laser systems are often fluence-limited by multilayer thin films deposited on the optical surfaces. When comparing publications within the laser damage literature, there can be confusing and conflicting laser damage results. This is due to differences in testing protocols between research groups studying very different applications. In this series of competitions, samples from multiple vendors are compared under identical testing parameters and a single testing service. Unlike a typical study where a hypothesis is tested within a well-controlled experiment with isolated variables, this competition isolates the laser damage testing variables so that trends can be observed between different deposition processes, coating materials, cleaning techniques, and multiple coating suppliers. The resulting series of damage competitions has also been designed to observe general trends of damage morphologies and mechanisms over a wide range of coating types (high reflector and antireflector), wavelengths (193 to 1064 nm), and pulse lengths (180 fs to 13 ns). A double blind test assured sample and submitter anonymity were used in each of the competitions so only a summary of the deposition process, coating materials, layer count and spectral results are presented. Laser resistance was strongly affected by substrate cleaning, coating deposition method, and coating material selection whereas layer count and spectral properties had minimal impact.

42 ENGINEERING↗

Insights into accelerated aging of SSL luminaires

Although solid-state lighting (SSL) products are often intended to have product lifetimes of 15 years or more, the rapid change in technology has created a need for accelerated life tests (ALTs) that can be performed in the span of several months. A critical element of interpreting results from any systems-level ALT is understanding of the impact of the test environment on each component. Because of its ubiquity in electronics, the use of temperature-humidity environments as potential ALTs for SSL luminaires was investigated. Results from testing of populations of three commercial 6” downlights in environments of 85oC and 85% relative humidity (RH) and 75oC and 75% RH are reported. These test environments were found to accelerate lumen depreciation of the entire luminaire optical system, including LEDs, lenses, and reflectors. The effects of aging were found to depend strongly on both the optical materials that were used and the design of the luminaire; this shows that the lumen maintenance behavior of SSL luminaires must be addressed at the optical systems level. Temperature-Humidity ALTs can be a useful test in understand lumainaire depreciation provided that proper consideration is given to the different aging rates of various materials. Since the impact of the temperature-humidity environment varies among components of the optical system, uniform aging of all system components in a single test is difficult to achieve.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

A Comparison of Different NDE Signal Processing Techniques Based on Waveform Entropies Applied to Long Fiber Graphite/Epoxy Plates

This study compares different approaches for imaging the internal architecture of graphite/epoxy composites using backscattered ultrasound. Two cases are studied. In the first, near-surface defects in a thin graphite/epoxy plates are imaged. The same backscattered waveforms were used to produce peak-to-peak, logarithm of signal energy, as well as entropy images of different types. All of the entropy images exhibit better border delineation and defect contrast than the either peak-to-peak or logarithm of signal energy. The best results are obtained using the joint entropy of the backscattered waveforms with a reference function. Two different references are examined. The first is a reflection of the insonifying pulse from a stainless steel reflector. The second is an approximate optimum obtained from an iterative parametric search. The joint entropy images produced using this reference exhibit three times the contrast obtained in previous studies. These plates were later destructively analyzed to determine size and location of near-surface defects and the results found to agree with the defect location and shape as indicated by the entropy images. In the second study, images of long carbon graphite fibers (50% by weight) in polypropylene thermoplastic are obtained as a first step toward ultrasonic determination of the distributions of fiber position and orientation.

Entropy Imaging↗

Optical design of PICO: a concept for a space mission to probe inflation and cosmic origins

The Probe of Inflation and Cosmic Origins (PICO) is a probe-class mission concept currently under study by NASA. PICO will probe the physics of the Big Bang and the energy scale of inflation, constrain the sum of neutrino masses, measure the growth of structures in the universe, and constrain its reionization history by making full sky maps of the cosmic microwave background with sensitivity 80 times higher than the Planck space mission. With bands at 21-799 GHz and arcmin resolution at the highest frequencies, PICO will make polarization maps of Galactic synchrotron and dust emission to observe the role of magnetic fields in Milky Way's evolution and star formation. We discuss PICO's optical system, focal plane, and give current best case noise estimates. The optical design is a two-reflector optimized open-Dragone design with a cold aperture stop. It gives a diffraction limited field of view (DLFOV) with throughput of 910 cm 2 sr at 21 GHz. The large 82 square degree DLFOV hosts 12,996 transition edge sensor bolometers distributed in 21 frequency bands and maintained at 0.1 K. We use focal plane technologies that are currently implemented on operating CMB instruments including three-color multi-chroic pixels and multiplexed readouts. To our knowledge, this is the first use of an open-Dragone design for mm-wave astrophysical observations, and the only monolithic CMB instrument to have such a broad frequency coverage. Finally, with current best case estimate polarization depth of 0.65 μKCMB-arcmin over the entire sky, PICO is the most sensitive CMB instrument designed to date.

79 ASTRONOMY AND ASTROPHYSICS↗

The impact of contamination and aging effects on the long-term laser-damage resistance of SiO 2 /HfO 2 /TiO 2 high-reflection coatings for 1054nm

The laser damage thresholds of optical coatings can degrade over time due to a variety of factors, including contamination and aging. Optical coatings deposited using electron beam evaporation are particularly susceptible to degradation due to their porous structure. In a previous study, the laser damage thresholds of optical coatings were reduced by roughly a factor of two from 2013 to 2017. The coatings in question were high reflectors for 1054 nm that contained SiO 2 and HfO 2 and/or TiO 2 layers, and they were stored in sealed PETG containers in a class 100 cleanroom with temperature control. At the time, it was not certain whether contamination or thin film aging effects were responsible for the reduced laser damage thresholds. Therefore, to better understand the role of contamination, the coatings were recleaned and the laser damage thresholds were measured again in 2018. Here, the results indicate that contamination played the most dominant role in reducing the laser damage thresholds of these optical coatings, even though they were stored in an environment that was presumed to be clean.

42 ENGINEERING↗

Spatio-temporal evolution of femtosecond laser pulses in dielectric multi-layers controlling the damage behavior

When designing femtosecond laser mirrors, one tries to minimize the peak intensity within the high-index layers to increase the laser-induced damage threshold. Typically, the optimization procedure utilizes the electric field distribution in the layer stack generated by monochromatic irradiation. Furthermore, this approach is sufficient for certain structures like high-reflectors based on quarter-wave films. More complex structures require to take into account the exact evolution of the pulse parameters such as peak intensity and duration within the multi-layer system. We exemplify this by discussing a merit function that can be included in femtosecond optics design.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗