Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Propulsion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Nuclear Thermal Propulsion (NTP) Fission Product and Source Term Analysis

Nuclear thermal propulsion (NTP) is an in-space propulsion technology that uses a nuclear reactor to directly heat a propellant to provide high thrust, at higher efficiencies than achievable with conventional chemical propulsion systems. Due to the ability of NTP rockets to efficiently provide high thrust, this technology has been proposed for long duration space missions such as crewed missions to Mars and beyond. A primary hurdle for NTP technology development is the demonstration of an integrated reactor engine system to verify its functionality and performance. This primarily requires the manufacture and testing of candidate reactor and engine technologies to demonstrate the proposed design enables desired performance and exhibits acceptable response under all known operation modes. A major component in this testing is fission product accumulation, since after operation radioactive isotopes can be produced and pose radiological dose concerns. This paper explains the background behind fission product analysis and the methodology used to evaluate current reactor designs and identify the amount of fission products present and their radiological impact. Results of multiple thrust level engines at different time periods are discussed and highlight the need for additional experimental testing to confirm fractional release levels of fission products out of the system. Benchmarking of models and future paths of analysis are also discussed.

Nuclear Thermal Propulsion↗
NASA NTRSDate not supplied

Considerations for Nuclear Thermal Propulsion Reactor Technology Readiness Level Advancement

Nuclear thermal propulsion (NTP) is a candidate in-space propulsion technology for crewed missions to Mars. An NTP engine relies on the use of a reactor as a heat exchanger to directly heat a hydrogen propellant which is expanded through a nozzle for high specific impulse (> 850s), high thrust (>15 klbf) propulsion. NTP reactor and engine technologies are currently being developed to enable a future NTP engine prototype demonstration. Technology readiness level (TRL) definitions are a useful tool to plan necessary technology advancement tasks as they provide guidance on expected development activities and necessary level of fidelity of test article or testing conditions for demonstration tasks. However, technology readiness definitions for an NTP reactor and related demonstration tasks have not yet been defined. This paper identifies relevant TRL definitions by the National Aeronautics and Space Administration (NASA) and Department of Energy (DOE). Based on these definitions, preliminary recommendations on testing conditions and important parameters to consider for NTP reactor technology development planning are provided for TRL 1 - 6. As a part of this effort, functional characteristics and important performance parameters for the reactor are identified, as well as a summary of relevant literature which was considered when assessing development tasks capable of meeting TRL definition criteria.

nuclear thermal propulsion↗
NASA NTRSDate not supplied

Numerical Propulsion System Simulation (NPSS) Power Systems Library

This presentation covers the Numerical Propulsion System Simulation (NPSS) Power Systems Library being developed by NASA. This library is a set of components, models, and interfaces for the NPSS language to enable building electric power system models for electrified propulsion systems. The presentation is to be given at the 3rd annual RVLT Toolchain Workshop, where attendees from across the eVTOL industry will be informed of NASA’s tools for eVTOL conceptual design from the vehicle level down through subsystems including propulsion, noise, electrical power, and others. It covers where the NPSS Power System Library fits into NASA’s RVLT toolchain and RVLT work in general, and will inform the audience of how the tool can be useful in their own work.

Electric vertical takeoff and landing↗
NASA NTRSDate not supplied

Hybrid-Electric Aero-Propulsion Controls Laboratory: Overview and Capability

A hardware-in-the-loop (HIL) laboratory is developed to investigate control technologies for electrified aircraft propulsion (EAP). The laboratory emulates a propulsion system by reproducing the mechanical shaft interface to the electrical power system in hardware. The experimental electric power system includes supercapacitor energy storage and a dynamically variable electrical load. A novel method of scaling power and inertia is provided in software to accurately reproduce the transient, off-design turbomachinery performance dynamics without including actual turbomachinery. An overview of how the HIL system can accommodate a broad range of EAP architectures, including power extraction and insertion, with capability for transient energy management is described. The real-time system operates in the 100kW power class and is instrumented to emulate turbomachinery – power system interactions. The platform is an agile, flexible laboratory for low-cost, risk-reduction development and testing of propulsion control, operability, and energy management technologies.

Controls↗
NASA NTRSDate not supplied

Hybrid-Electric Aero-Propulsion Controls Laboratory: Overview and Capability

A hardware-in-the-loop (HIL) laboratory is developed to investigate control technologies for electrified aircraft propulsion (EAP). The laboratory emulates a propulsion system by reproducing the mechanical shaft interface to the electrical power system in hardware. The experimental electric power system includes supercapacitor energy storage and a dynamically variable electrical load. A novel method of scaling power and inertia is provided in software to accurately reproduce the transient, off-design turbomachinery performance dynamics without including actual turbomachinery. An overview of how the HIL system can accommodate a broad range of EAP architectures, including power extraction and insertion, with capability for transient energy management is described. The real-time system operates in the 100kW power class and is instrumented to emulate turbomachinery – power system interactions. The platform is an agile, flexible laboratory for low-cost, risk-reduction development and testing of propulsion control, operability, and energy management technologies.

controls↗
NASA NTRSDate not supplied

Harnessing the Digital Transformation for Development of Electrified Aircraft Propulsion Control Systems

Hybrid electric aircraft propulsion is an emerging technology that presents a variety of potential benefits along with technical integration challenges. Developing these new propulsion architectures with their complex control systems, and ultimately proving their benefit, is a multistep process that goes from concept, to analysis, to dynamic simulation, to hardware in the loop testing, to full scale testing and beyond. This effort is being revolutionized and indeed enabled by new digital tools that support the increasing technology readiness level throughout the maturation process. NASA has developed and made available a suite of digital tools that ease the path from concept to implementation. The three packages are the Toolbox for the Modeling and Analysis of Thermodynamic Systems (T-MATS), the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), and the Thermal Systems Analysis Toolbox (TSAT). These tools are interactive, complementary, and compatible with each other. T-MATS is a modular thermodynamic modeling framework designed for creating custom component level models of jet engines. EMTAT is a modeling framework used to simulate a variety of power electronic devices, using both physics-based and power flow calculations. TSAT is a framework for modeling and analysis of dynamic heat transfer. These packages all consist of graphical, drag-and-drop, parameterizable building blocks representing various components of the system to be modeled, e.g., compressors, turbines, motors, energy storage devices, etc. They are designed to enable the user to model and simulate the end-to-end dynamic operation of a hybrid powertrain at the timescale of the turbomachinery, capturing mechanical, electrical, and thermal interactions. This paper will describe through multiple examples how these tools have been used successfully in several of the early stages of hybrid electric propulsion system development, from the initial system modeling to real-time interactive pilot-in-the-loop simulation to physical hardware-in-the-loop testing, each step bringing the technology closer to fruition.

Hybrid electric propulsion↗
NASA NTRSDate not supplied

Harnessing the Digital Transformation for Development of Hybrid Electric Aircraft Propulsion Control Systems

Hybrid electric aircraft propulsion is an emerging technology that presents a variety of potential benefits along with technical integration challenges. Developing these new propulsion architectures with their complex control systems, and ultimately proving their benefit, is a multistep process that goes from concept, to analysis, to dynamic simulation, to hardware in the loop testing, to full scale testing and beyond. This effort is being revolutionized and indeed enabled by new digital tools that support the increasing technology readiness level throughout the maturation process. NASA has developed and made available a suite of digital tools that ease the path from concept to implementation. The three packages are the Toolbox for the Modeling and Analysis of Thermodynamic Systems (T-MATS), the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), and the Thermal Systems Analysis Toolbox (TSAT). These tools are interactive, complementary, and compatible with each other. T-MATS is a modular thermodynamic modeling framework designed for creating custom component level models of jet engines. EMTAT is a modeling framework used to simulate a variety of power electronic devices, using both physics-based and power flow calculations. TSAT is a framework for modeling and analysis of dynamic heat transfer. These packages all consist of graphical, drag-and-drop, parameterizable building blocks representing various components of the system to be modeled, e.g., compressors, turbines, motors, energy storage devices, etc. They are designed to enable the user to model and simulate the end-to-end dynamic operation of a hybrid powertrain at the timescale of the turbomachinery, capturing mechanical, electrical, and thermal interactions. This paper will describe through multiple examples how these tools have been used successfully in several of the early stages of hybrid electric propulsion system development, from the initial system modeling to real-time interactive pilot-in-the-loop simulation to physical hardware-in-the-loop testing, each step bringing the technology closer to fruition.

Electrified Propulsion↗
NASA NTRSDate not supplied

Flight Performance Estimates for the NASA X-57 Distributed Electric Propulsion Flight Demonstrator

The X-57 flight demonstrator concept featured four configurations starting with a conventional combustion-powered multiengine airplane and ending with a fully electric configuration with two forms of distributed propulsion and a highly modified wing. These configurations, called Mods, were designed to gain incremental insight into different aircraft propulsion configuration options and their impact on the aircraft performance. The gasoline-powered Mod I configuration consumed 2.6 to 2.9 times more stored energy in cruise than the electric but otherwise conventionally configured Mod II configuration. The highly loaded wing of Mod III led to an increase of 40% in the power-off lift-to-drag ratio as compared to Mod II at the project high-speed cruise target speed and altitude. The power-on lift-to-drag ratio of Mod III was 53% higher than Mod II due to the beneficial aero-propulsive interaction of the wingtip-mounted cruise propellers in Mod III. The high-lift propeller system of Mod IV recovered the low-speed performance of the conventional configuration in Mod II that was otherwise lost with the introduction of the highly loaded Mod III wing. The battery-electric configurations also benefitted from a lack of power lapse in the electric motors with increasing air density as compared to the combustion-powered baseline aircraft.

Distributed Performance↗
NASA NTRSDate not supplied

Flight Performance Estimates for the NASA X-57 Distributed Electric Propulsion Flight Demonstrator

The X-57 flight demonstrator concept featured four configurations starting with a conventional combustion-powered multiengine airplane and ending with a fully electric configuration with two forms of distributed propulsion and a highly modified wing. These configurations, called Mods, were designed to gain incremental insight into different aircraft propulsion configuration options and their impact on the aircraft performance. The gasoline-powered Mod I configuration consumed 2.6 to 2.9 times more stored energy in cruise than the electric but otherwise conventionally configured Mod II configuration. The highly loaded wing of Mod III led to an increase of 40% in the power-off lift-to-drag ratio as compared to Mod II at the project high-speed cruise target speed and altitude. The power-on lift-to-drag ratio of Mod III was 53% higher than Mod II due to the beneficial aero-propulsive interaction of the wingtip-mounted cruise propellers in Mod III. The high-lift propeller system of Mod IV recovered the low-speed performance of the conventional configuration in Mod II that was otherwise lost with the introduction of the highly loaded Mod III wing. The battery-electric configurations also benefitted from a lack of power lapse in the electric motors with increasing air density as compared to the combustion-powered baseline aircraft.

Distributed Performance↗
NASA NTRSDate not supplied

Aero-Propulsive Damping Characterization for eVTOL Aircraft Using Free Motion Wind-Tunnel Testing

This paper describes an electric vertical takeoff and landing (eVTOL) aircraft system identification method applied using three degree-of-freedom (3DOF) free motion wind-tunnel testing. The approach, similar to flight-test system identification, allows for efficient mathematical model development of the aero-propulsive moments applied on an eVTOL vehicle, including aerodynamic damping effects. The approach is demonstrated using a subscale tiltrotor eVTOL aircraft mounted on a new 3DOF wind-tunnel apparatus. To execute the test, a model-based 3DOF control system is designed to track attitude commands and transition the aircraft based on the freestream dynamic pressure. While the flight controller is active, orthogonal phase-optimized multisine inputs are injected into the attitude command and control effector command signals to enable collection of informative data for model identification. Aero-propulsive models are then identified at several reference conditions in the transition flight envelope using the equation-error method in the frequency domain. The identified models are shown to have a good fit to the modeling data and good prediction capability of data not used for model identification. The method yields aerodynamic damping estimates using less wind-tunnel test time compared to traditional forced oscillation experiments and supplements static wind-tunnel testing to produce a comprehensive transition aero-propulsive model suitable for use in flight dynamics simulations.

RAVEN↗
NASA NTRSDate not supplied

Introduction to Metal Additive Manufacturing for Propulsion Applications: Part I and II

Additive Manufacturing (AM) has become a prominent technology of interest for manufacturing propulsion components and gaining attention across the aerospace industry. AM is maturing at a rapid pace and providing new design opportunities, novel materials, new industries and supply chains resulting in programmatic and technical performance improvements. The successful use of AM requires a methodical and intentional approach to understanding the concept to utilization lifecycle for AM. This course will provide an overview of the various steps in AM process trades, design, build process, post-processing, certification and infusion of AM. This will provide various lessons learned and experiences that were captured in a recent AIAA textbook titled "Metal Additive Manufacturing for Propulsion Applications" by the session chairs and industry colleagues. This course will include propulsion examples and that went through the AM lifecycle including hot-fire testing.

Additive Manufacturing↗
NASA NTRSDate not supplied

Fabrication and Mechanical Testing of Heat Exchanger Tubes for Nuclear Propulsion and Other Applications from Continuous Carbon Nanotube Yarns and Tapes

As NASA and other agencies are looking to conduct sustained operations in space, nuclear engines have been receiving increased focus. The high specific impulse and high fuel efficiency at high thrust output of these engines can halve the transit time for human missions to Mars, or enable missions requiring multiple orbital parameter adjustments. In both Nuclear Thermal Propulsion (NTP) and Nuclear Electric Propulsion (NEP) systems, heat exchangers play a critical role in transferring energy from the reactor to a working fluid, hydrogen in the case of NTP and a molten salt or other fluid for electricity generation in NEP. Heat exchangers are also required in other parts of the spacecraft. Various manufacturing methods and materials are being considered for the heat exchangers. In this presentation the fabrication and testing of heat exchangers made from continuous carbon nanotube (CNT) yarns and tapes are discussed. The fabrication workflow is compared and contrasted, as well as performance of prototype heat exchanger tubes fabricated using the various CNT formats. The failure loads and mechanisms of the tubes under tensile, compression, and bending loads are assessed. A further comparison of the CNT materials to components fabricated from carbon fiber is made. The presented work will contribute to the selection of approaches for heat exchanger fabrication methods for nuclear propulsion and other applications.

Heat Exchanger↗
NASA NTRS2026

Recommended Practice for Use of ExB Probes in Electric Propulsion Testing

An ExB probe is an electric propulsion plume diagnostic that has at its core a Wien filter. Ions entering the instrument experience perpendicular electric and magnetic fields and are filtered based on their velocity. While the ExB probe can be used to estimate the ion velocity distribution function, in the electric propulsion community, it is commonly used to measure species fractions. There are numerous probe designs, implementation and operation procedures, and data analysis approaches described and in use across the community. This paper provides recommendations and descriptions of best practices for design, implementation, and data analysis for the ExB probe, with a particular emphasis on Hall and ion thrusters. This work contributes to the broader community goal to standardize the use of diagnostics in electric propulsion testing.

ExB probe↗
NASA NTRS2015

Airvolt Aircraft Electric Propulsion Test Stand

Development of an electric propulsion test stand that collects high-fidelity data of motor, inverter, and battery system efficiencies; thermal dynamics; and acoustics independent of manufacturer reported values will improve understanding of electric propulsion systems to be used in future aircraft. A buildup approach to this development reveals new areas of research and best practices in testing, and attempts to establish a standard for testing these systems.

propulsion↗
DOE OSTI2020

Assessment of Near-Term Fuel Screening and Qualification Needs for Nuclear Thermal Propulsion Systems

Nuclear thermal propulsion (NTP) is an in-space propulsion technology capable of both high specific impulse (850–1000 s) and thrust (44–1112 kN), which can help reduce trip times for crewed missions beyond low Earth orbit. NTP technology has been demonstrated during historic programs. Over 20 ground test reactor experiments were performed, which demonstrated the prototypic reactor operations, during the Nuclear Engine for Rocket Vehicle Application (NERVA)/Rover program (1955–1972). Although historical programs have shown that NTP is a viable in-space propulsion technology, developing NTP in modern programs is contingent on the development and qualification of ultrahigh-temperature nuclear fuel technologies that can withstand engine operating conditions. In historical NTP development programs such as NERVA/Rover, prototypic reactor/engine schemes were ground tested to assess the overall system feasibility and to qualify the reactor fuel forms for eventual flight systems. Although this approach is effective to verify fuel performance under prototypic conditions, relying solely on full-scale NTP reactor tests as the pathway for verifying or qualifying fuel is inefficient and cost prohibitive today. Additionally, modern nuclear licensing requirements state that before test reactor approval, reactor components and fuel elements should be qualified via non-nuclear (out-of-pile) and nuclear (in-pile) testing under representative operating conditions. Using this methodology, fuel matures as production scale fabrication methods are established, and as produced fuel performance is demonstrated. Here, this paper provides an overview of historical approaches to NTP fuel performance maturation, including fuel screening and qualification needs, and provides insight for establishing an efficient testing paradigm that can be implemented to rapidly and affordably develop NTP fuel forms for eventual qualification.

42 ENGINEERING↗
DOE OSTI2023

Alternative Power and Propulsion for Space Systems

What are the main sources of power and propulsion for space systems and what are their advantages, disadvantages, how do they work, and what are the politics behind them? The following topics will be analyzed solar panels, batteries, radioisotope thermoelectric generator (RTG), advanced Stirling radioscopic generator (ASRG), reactors, nuclear thermal rockets (NTP), thermionic experiment with conversion (TOPAZ), electrothermal plasma thruster (VASIMR), ion propulsion, and finally nuclear pulse propulsion. The production of Pu-238 is extremely controversial but a vital source of fuel for many of these space systems. Soral and Batteries are the most common and the least controversial forms of power used in space systems today. However, is ineffective for deep space exploration as they only function for up to four years without needing to be recharged. This is where nuclear systems come into play. Nuclear systems such as an RTG will “live” up to 88 years. For example, Voyager 1 is powered by an RTG It has been traveling since 1977 and has left out solar system in 2012 and has yet to run out of power. However, this type of technology (nuclear) has many hurtles it needs to jump through before advancements in can go much further.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1971

Solar electric propulsion system technology

Achievements in the solar electric propulsion system technology program (SEPST 3) are reported and certain propulsion system-spacecraft interaction problems are discussed. The basic solar electric propulsion system concept and elements are reviewed. Hardware is discussed only briefly, relying on detailed fabrication or assembly descriptions reported elsewhere. Emphasis is placed on recent performance data, which are presented to show the relationship between spacecraft requirements and present technology.

Masek, T. D.↗
NASA NTRS1972

Comparison of the solar sail with electric propulsion systems

The propulsive efficiencies of the solar sail and of electric propulsion systems are compared on the basis of specific impulse. It is shown that the solar sail is more efficient at one a.u. for mission durations greater than about two months, that the advantage is increased for missions toward the inner planets, and that the same conclusions are reached when the comparison is based on maximizing the momentum transferred to the payload. Other factors that will influence the choice of a propulsion system for a specific mission are mentioned.

Macneal, R. H.↗