Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Performance Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Effect of rotor design tip seed on aerodynamic performance of a model VTOL lift fan under static and crossflow conditions

Results are presented for a wind tunnel investigation of three single VTOL lift fan stages designed for the same overall total pressure ratio at different rotor tip speeds. The stages were tested in a model lift fan installed in a wing pod. The three stages had essentially the same aerodynamic performance along the operating line. However, differences in stage thrust characteristics were obtained when a variation in back pressure was imposed on the stages by cross-flow effects and thrust-vectoring louvers.

Stockman, N. O.↗

Aerodynamic performance of 0.4066-scale model to JT8D refan stage

The aerodynamic performance of a scale model of the split flow JT8D rafan stage is presented over a range of flows at speeds from 40 to 100 percent design. The bypass stage peak efficiency of 0.800 occurred at a total weight flow of 35.82 kilograms per second and a pressure ratio of 1.697. The stall margin was 15 percent based on pressure ratio and weight flow at stall and peak efficiency conditions. The data indicated that the hub region of the core stators was choked at design speed over the entire flow range tested.

Moore, R. D.↗

ST7 Disturbance Reduction System (DRS) Colloid Micronewton Thruster Performance and Control Algorithm Model Simulation Validation in Flight

Colloid Micronewton Thrusters (CMNT) were flight demonstrated for the first time on the ST7Disturbance Reduction System (DRS) payload on the European Space Agency (ESA) Laser Interferometer Space Antenna (LISA) Pathfinder spacecraft for attitude and drag-free spacecraft control. LISA Pathfinder was a technology demonstration mission for ESA’s LISA gravitational wave observatory, currently in Phase A with a launch date of 2034. The DRS included the Integrated Avionics Unit (IAU), eight Colloid Micronewton Thrusters (CMNT), Dynamic Control Software (DCS) and Flight Software (FSW). The CMNT technology met performance requirements operating at 5-30 µN of thrust with ≤0.1 µN resolution and ≤0.1 µN/Hz thrust noise to deliver the required nanometer-level precision spacecraft control measured by the gravitational reference sensor (GRS) in the ESA LISA Technology Package (LTP). The performance of seven of the CMNT in flight was consistent with ground test results. The colloid thruster performance model of thrust and thrust noise as a function of operational parameters (i.e. beam current, voltage, temperature, etc.) was validated in flight over a wide range of conditions. A model and simulation of the thruster control algorithm was developed and validated with flight data to predict thrust noise. This capability is important because it is considered to be a significant source of position noise on the spacecraft and, therefore, the acceleration noise on the test masses, which provide the gravity wave measurements. The CMNT thruster model data and validation with LISA Pathfinder/ST7-DRS flight experiments are discussed in this paper.

Hruby, Vlad↗

ASPIRE Aerodynamic Models and Flight Performance

The Advanced Supersonic Parachute Inflation Research Experiments (ASPIRE) project waslaunched to develop the capability for testing supersonic parachutes at Mars-relevant conditions.Three initial parachute tests, targeted as a risk-reduction activity for NASA's upcomingMars2020 mission, successfully tested two candidate parachute designs and provided valuabledata on parachute inflation, forces, and aerodynamic behavior. Design of the flight tests dependedon flight mechanics simulations which in turn required aerodynamic models for the payload, andthe parachute. Computational Fluid Dynamics (CFD) was used to generate these models preflightand are compared against the flight data after the tests. For the payload, the reconstructedaerodynamic behavior is close to the pre-flight predictions, but the uncertainties in thereconstructed data are high due to the low dynamic pressures and accelerations during the flightperiod of comparison. For the parachute, the predicted time to inflation agrees well with the preflightmodel; the peak aerodynamic force and the steady state drag on the parachute are withinthe bounds of the pre-flight models, even as the models over-predict the parachute drag atsupersonic Mach numbers. Notably, the flight data does not show the transonic drag decreasepredicted by the pre-flight model. The ASPIRE flight tests provide previously unavailablevaluable data on the performance of a large full-scale parachute behind a slender leading bodyat Mars-relevant Mach number, dynamic pressure and parachute loads. This data is used topropose a new model for the parachute drag behind slender bodies to aid future experiments.

Muppidi, Suman↗

ASPIRE Aerodynamic Models and Flight Performance

The Advanced Supersonic Parachute Inflation Research Experiments (ASPIRE) project waslaunched to develop the capability for testing supersonic parachutes at Mars-relevant conditions.Three initial parachute tests, targeted as a risk-reduction activity for NASA's upcoming Mars2020 mission, successfully tested two candidate parachute designs and provided valuable data onparachute inflation, forces, and aerodynamic behavior. Design of the flight tests depended onflight mechanics simulations which in turn required aerodynamic models for the payload, andthe parachute. Computational Fluid Dynamics (CFD) was used to generate these models preflightand they are compared against the flight data after the tests. For the payload, thereconstructed aerodynamic behavior is close to the pre-flight predictions, but the uncertaintiesin the reconstructed data are high due to the low dynamic pressures and accelerations duringthe flight period of comparison. For the parachute, the predicted time to inflation agrees wellwith the pre-flight model; the peak aerodynamic force and the steady state drag on the parachuteare within the bounds of the pre-flight models, even as the models over-predict the parachutedrag at supersonic Mach numbers. Notably, the flight data do not show the transonic dragdecrease predicted by the pre-flight model. The ASPIRE flight tests provide previouslyunavailable valuable data on the performance of a large full-scale parachute behind a slenderleading body at Mars-relevant Mach number, dynamic pressure and parachute loads. TheASPIRE results are used to propose a new model for the parachute drag behind slender bodiesto aid future experiments.

Muppidi, Suman↗

Generic icing effects on forward flight performance of a model helicopter rotor

An experimental program using a commercially available model helicopter has been conducted in the TAMU 7 ft x 10 ft Subsonic Wind Tunnel to investigate main rotor performance degradation due to generic ice adhesion. Base and iced performance data were gathered as functions of fuselage incidence, blade collective pitch, main rotor rotational velocity, and freestream velocity. The experimental values have shown that, in general, the presence of generic ice introduces decrements in performance caused by leading edge separation regions and increased surface roughness. In addition to the expected changes in aerodynamic forces caused by variations in test Reynolds number, forward flight data seemed to be influenced by changes in freestream and rotational velocity. The dependence of the data upon such velocity variations was apparently enhanced by increases in blade chord.

Tinetti, Ana F.↗

Modeling to predict pilot performance during CDTI-based in-trail following experiments

A mathematical model was developed of the flight system with the pilot using a cockpit display of traffic information (CDTI) to establish and maintain in-trail spacing behind a lead aircraft during approach. Both in-trail and vertical dynamics were included. The nominal spacing was based on one of three criteria (Constant Time Predictor; Constant Time Delay; or Acceleration Cue). This model was used to simulate digitally the dynamics of a string of multiple following aircraft, including response to initial position errors. The simulation was used to predict the outcome of a series of in-trail following experiments, including pilot performance in maintaining correct longitudinal spacing and vertical position. The experiments were run in the NASA Ames Research Center multi-cab cockpit simulator facility. The experimental results were then used to evaluate the model and its prediction accuracy. Model parameters were adjusted, so that modeled performance matched experimental results. Lessons learned in this modeling and prediction study are summarized.

Sorensen, J. A.↗

An evaluative model of system performance in manned teleoperational systems

Manned teleoperational systems are used in aerospace operations in which humans must interact with machines remotely. Manual guidance of remotely piloted vehicles, controling a wind tunnel, carrying out a scientific procedure remotely are examples of teleoperations. A four input parameter throughput (Tp) model is presented which can be used to evaluate complex, manned, teleoperations-based systems and make critical comparisons among candidate control systems. The first two parameters of this model deal with nominal (A) and off-nominal (B) predicted events while the last two focus on measured events of two types, human performance (C) and system performance (D). Digital simulations showed that the expression A(1-B)/C+D) produced the greatest homogeneity of variance and distribution symmetry. Results from a recently completed manned life science telescience experiment will be used to further validate the model. Complex, interacting teleoperational systems may be systematically evaluated using this expression much like a computer benchmark is used.

Haines, Richard F.↗

Aeroacoustic performance of scale model sonic inlets

Various means can be used to vary engine inlet throat areas in order to reduce noise generated at takeoff and approach. Low-speed wind-tunnel tests were performed to evaluate the aeroacoustic performance of two takeoff geometries (cylindrical centerbody and bulb-shaped centerbody) and four approach geometries (bulb-shaped centerbody, annular ring, radial vanes, and step diffuser). The effects of inlet internal lip shape and diffuser length on sonic inlet performance were also investigated. It was found that the single-passage geometries, in particular a cylindrical centerbody takeoff geometry and a bulb-shaped centerbody approach geometry, provide the highest level of aeroacoustic performance. Increasing the inlet lip contraction ratio extends the maximum incidence angle for attached lip flow, while increasing the inlet diffuser length increases total pressure recovery for a given amount of noise suppression.

Abbott, J. M.↗

Wake Vortex Algorithm Scoring Results

This report compares the performance of two models of trailing vortex evolution for which interaction with the ground is not a significant factor. One model uses eddy dissipation rate (EDR) and the other uses the kinetic energy of turbulence fluctuations (TKE) to represent the effect of turbulence. In other respects, the models are nearly identical. The models are evaluated by comparing their predictions of circulation decay, vertical descent, and lateral transport to observations for over four hundred cases from Memphis and Dallas/Fort Worth International Airports. These observations were obtained during deployments in support of NASA's Aircraft Vortex Spacing System (AVOSS). The results of the comparisons show that the EDR model usually performs slightly better than the TKE model.

Robins, R. E.↗

An injector design model for predicting rocket engine performance and heat transfer

A model is formulated for estimating the performance and chamber heat transfer in rocket injectors/chambers operating with gaseous H2-O2 propellants. The model quantifies the combustion performance and chamber heat flux for variables such as chamber length, element type, element area ratio, impingement angle, thrust/element, mixture ratio, moment ratio, element spacing, and physical size. Design equations are given and curves are plotted for evaluation of combustion performance in injectors comprised of F-O-F triplet, premix, coaxial and swirl coaxial element types. Curve plots and equations are also included for estimation of the chamber wall heat fluxes generated by these element types.

Calhoon, D. F.↗

Mass distribution and performance of free flight models

This note deals with the mass distribution and performance of free flight models. An airplane model which is to be used in free flight tests must be balanced dynamically as well as statically, e.g., it must not only have a given weight and the proper center of gravity but also a given ellipsoid of inertia. Equations which relate the motions of an airplane and its model are given. Neglecting scale effect, these equations may be used to predict the performance of an airplane, under the action of gravity alone, from data obtained in making dropping tests of a correctly balanced model.

Scherberg, Max↗

Towards an Aviation Large Language Model by Fine-tuning and Evaluating Transformers

In the aviation domain, there are many applications for machine learning and artificial intelligence tools that utilize natural language. For example, there is a desire to know the commonalities in written safety reports such as voluntary post incidents reports or aerial wildfire operations reports to better understand the risks present. Another use-case is the possibility of extracting airspace procedures and constraints currently written in documents such as Letters of Agreement. These applications can benefit from the use of state-of-the-art natural language processing techniques when adapted to the language/phraseology specific to the aviation domain. This paper evaluates the viability of adaptation of NLP tools to the aviation domain by fine-tuning transformer based models using aviation data sets. In 2018, a novel language model based on neural units (also called transformers) was created and became known as “Bidirectional Encoder Representations from Transformers” or BERT. This architecture combined with large amounts of English training data and innovative semi-supervised training tasks set the standard for what would later emerge as Large Language Models. The performance of these models was further improved by hyperparameter tuning and refinement of the semi-supervised training task and resulted in “Robustly Optimized BERT Pre-training Approach through hyperparameter tuning” or RoBERTa models. These pre-trained Large Language Models proved to be useful for a wide variety of natural language processing tasks such as text classification and question answering through a process called fine-tuning. The transformer architecture with pre-trained weights served as the basis with the last few layers replaced with layers fine-tuned to perform a new task e.g., a layer that provides a label for the entire input text. This process of fine-tuning can also be used to adapt the models to new domains; e.g., BioBERT started with the pre-trained BERT model and was completed by additional fine-tuning and training on biomedical documents. Transformer-based architectures can also be used to create rich representations of text called embeddings which can serve as the input to other machine learning models. This allows simpler algorithms such as logistic regression to use context-rich representations of the text while still remaining quick to train and evaluate. In the world of aviation, there is a growing demand for natural language processing and understanding but the domain presents unique challenges. Due to the technical content (and specialized language) of most aviation documents, fine-tuning pre-trained Large Language Models to specific tasks has not met the benchmark on natural language processing tasks set by simpler models trained from scratch on the data. To address this deficiency, this paper evaluates the improvements from fine-tuning a Large Language Model on a large set of aviation documents using the original semi-supervised training tasks before performing specific natural language tasks. In fine-tuning, a domain-specific dataset is used on the original training task but with the pre-trained Large Language Model instead of starting from a random initialization. This approach allows the model to be adapted to the specific domain language without discarding the information gained from training on general English data. This paper utilized two major dataset types to train and assess the RoBERTa fine-tuning performance. The first are 7,057 Letters of Agreement which are Federal Aviation Administration (FAA) documents that formalize airspace operations across the national airspace system. They contain many examples of ‘aviation English’ using domain specific terminology and phrasing which serves as a representative basis to perform the semi-supervised fine-tuning. The second type is the 494 document classification labels to be used for evaluation. This down-stream evaluation aims to show the performance of the fine-tuned model, better understand how much data is needed for an effective fine-tuning, and how fine-tuning can be adapted for different applications in-the domain. After semi-supervised training, evaluation begins by encoding the documents for classification using the fine-tuned RoBERTa model. Then a logistic regression classifier is trained to label the document type and compared against our ground truth labels. This currently leads to a 82.8% accuracy on 10-fold cross validation showing improvement over baseline RoBERTa which achieved 81.0%. We plan to measure the improvements on additional tasks and it is expected that these improvements will lead to more robust models that can tackle the natural language processing challenges present in aviation datasets.

ATM↗

A Systems Approach to AI Model Integration and Performance Evaluation for the Generic UAM Simulation Framework

This paper introduces py-guam, an open-source experimentation framework developed for the NASA Generic Urban Air Mobility simulation (GUAM) environment, facilitating the integration and evaluation of advanced artificial intelligence (AI) algorithms. We present a systems approach which enables the seamless incorporation of data-driven models, including off-nominal and failure state detection, into the GUAM’s Cognitive Architecture (CA). The framework supports customizable experimentation parameters, derives Safety Performance Indicators (SPIs) from UL 4600 safety case analyses, and employs rapid UAM simulations to assess AI impacts on flight performance across diverse scenarios. Through comprehensive testing and validation experiments, we demonstrate GUAM’s capability to enhance safety and efficiency in urban air mobility operations. Additionally, the open-source nature of py-guam fosters community collaboration, ensuring continuous improvement and adaptability to evolving technological advancements. This work establishes a robust tool for developing and testing AI-driven urban air mobility (UAM) systems, advancing the safety and reliability of autonomous urban air vehicles.

Artificial Intelligence↗

A Practical Statistical Model for Telecommunications Performance Uncertainty

A statistical method, the probability distribution method, is presented which will give the probability of link performance values. The advantages of a design control procedure are preserved and optimum use of the system capabilities is permitted by improving the accuracy and completeness of the system model.

Yuen, J. H.↗

Extraction-Separation Performance and Dynamic Modeling of Orion Test Vehicles with Adams Simulation: 2nd Edition

NASA's Orion Capsule Parachute Assembly System (CPAS) project has advanced into the third generation of its parachute test campaign and requires technically comprehensive modeling capabilities to simulate multi-body dynamics (MBD) of test articles released from a C-17. Safely extracting a 30,000 lbm mated test article from a C-17 and performing stable mid-air separation maneuvers requires an understanding of the interaction between elements in the test configuration and how they are influenced by extraction parachute performance, aircraft dynamics, aerodynamics, separation dynamics, and kinetic energy experienced by the system. During the real-time extraction and deployment sequences, these influences can be highly unsteady and difficult to bound. An avionics logic window based on time, pitch, and pitch rate is used to account for these effects and target a favorable separation state in real time. The Adams simulation has been employed to fine-tune this window, as well as predict and reconstruct the coupled dynamics of the Parachute Test Vehicle (PTV) and Cradle Platform Separation System (CPSS) from aircraft extraction through the mid-air separation event. The test-technique for the extraction of CPAS test articles has evolved with increased complexity and requires new modeling concepts to ensure the test article is delivered to a stable test condition for the programmer phase. Prompted by unexpected dynamics and hardware malfunctions in drop tests, these modeling improvements provide a more accurate loads prediction by incorporating a spring-damper line-model derived from the material properties. The qualification phase of CPAS testing is on the horizon and modeling increasingly complex test-techniques with Adams is vital to successfully qualify the Orion parachute system for human spaceflight.

Fraire, Usbaldo, Jr.↗