Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PENETRATION DEPTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Architectural Effects on Impact Resistance of Uncoated MI SiC/SiC Composites

Impact tests were conducted on uncoated 2D and 2.5D MI SiC/SiC composite specimens at room temperature and 1316 C in air. The specimens were analyzed before and after impact using optical microscopy, pulsed thermography (PT) and computed tomography (CT). Preliminary results indicate the following. Both 2-D and 2.5D composites show increase in surface and volumetric damages with increasing impact velocity. However, 2-D composites are prone to delamination cracks. In both 2D and 2.5D composites, the magnitude of impact damage at a fixed impact velocity is slightly greater at room temperature than at 1315 C. At a fixed projectile velocity and test temperature, the depth of penetration of the projectile into the substrate is significantly lower in 2.5D composites than in 2D composites. Fiber architecture plays a significant role controlling impact damage in MI SiC/SiC composites.

Bhatt, R. T.↗

Validation of Proposed Metrics for Two-Body Abrasion Scratch Test Analysis Standards

Abrasion of mechanical components and fabrics by soil on Earth is typically minimized by the effects of atmosphere and water. Potentially abrasive particles lose sharp and pointed geometrical features through erosion. In environments where such erosion does not exist, such as the vacuum of the Moon, particles retain sharp geometries associated with fracturing of their parent particles by micrometeorite impacts. The relationship between hardness of the abrasive and that of the material being abraded is well understood, such that the abrasive ability of a material can be estimated as a function of the ratio of the hardness of the two interacting materials. Knowing the abrasive nature of an environment (abrasive)/construction material is crucial to designing durable equipment for use in such surroundings. The objective of this work was to evaluate a set of standardized metrics proposed for characterizing a surface that has been scratched from a two-body abrasion test. This is achieved by defining a new abrasion region termed Zone of Interaction (ZOI). The ZOI describes the full surface profile of all peaks and valleys, rather than just measuring a scratch width. The ZOI has been found to be at least twice the size of a standard width measurement; in some cases, considerably greater, indicating that at least half of the disturbed surface area would be neglected without this insight. The ZOI is used to calculate a more robust data set of volume measurements that can be used to computationally reconstruct a resultant profile for de tailed analysis. Documenting additional changes to various surface roughness par ameters also allows key material attributes of importance to ultimate design applications to be quantified, such as depth of penetration and final abraded surface roughness. Further - more, by investigating the use of custom scratch tips for specific needs, the usefulness of having an abrasion metric that can measure the displaced volume in this standardized manner, and not just by scratch width alone, is reinforced. This benefit is made apparent when a tip creates an intricate contour having multiple peaks and valleys within a single scratch. The current innovation consists of a software- driven method of quantitatively evaluating a scratch profile. The profile consists of measuring the topographical features of a scratch along the length of the scratch instead of the width at one location. The digitized profile data is then fed into software code, which evaluates enough metrics of the scratch to reproduce the scratch from the evaluated metrics. There are three key differences between the current art and this innovation. First, scratch width does not quantify how far from the center of the scratch damage occurs (ZOI). Second, scratch width does not discern between material displacement and material removal from the scratch. Finally, several scratches may have the same width but different zones of interactions, different displacements, and different material removals. The current innovation allows quantitative assessment of all three.

Street, Kenneth W., Jr.↗

Hypervelocity Impact Testing and MMOD Risk Reduction

Purpose: (1) Provide data to develop, update, and/or verify ballistic limit equations used in the MMOD risk assessment. (2) Provide data used to compare two or more shielding options to reduce MMOD risk. (3) Determine failure modes and failure criteria for hardware: (a) Failure modes: how hardware fails (pressure vessels, pressurized lines, electronic hardware, power cables). (b) Failure criteria: quantify damage level that results in hardware failure (for example: depth of penetration into pressure vessel that results in leak or burst).

Lear, Dana↗

The Application of Artificial Intelligence Deep Learning to Visually Identify Micrometeoroid and Orbital Debris Impacts

Recent advances in Artificial Intelligence (AI) are changing the World. Novel approaches to training AI systems have led to dramatic reductions in the amount of time required. Training an AI system could take years and teams of people using traditional methods, but with the advancements of Deep Learning (DL) models this training can now be accomplished by an individual in a matter of minutes. The development of “fast AI” libraries has delivered AI to essentially everyone. Democratization of AI power has inspired many to revisit past problems that will benefit from DL approaches. For example, the application of AI has improved detection of breast cancer by 20% compared to traditional detection methods. Computer vision and machine learning are being used to identify soil deficiencies and provide planting recommendations to farmers. Success stories like these and many others have provided inspiration to see if AI can help improve one of our needed capabilities – that of visually identifying micrometeoroid and orbital debris (MMOD) impact damage to spacecraft from images of the spacecraft exterior. The need to visually locate and characterize spacecraft MMOD impact damage has been present since the early days of space travel. This is often done by either having a crew member take photographs of the spacecraft through a window using a hand-held camera or ground personnel directing externally-mounted cameras. The photographs are then transmitted back to Earth for visual analysis. This method of MMOD damage inspection works well and has been used on various spacecraft including the Space Shuttle and the International Space Station (ISS). One of the issues with the current method that we believe AI could improve is the speed and possibly the accuracy in identifying MMOD impacts. Note that detecting MMOD impacts in images can be very difficult. The visual appearance of an MMOD impact can change dramatically with lighting conditions, size of impact, depth of penetration, material types, surface waviness, fabric coverings, camera & lens, distance to surface, spacecraft orientation, analyst experience, and many other factors. Currently, this takes a team of highly-experienced specialists in both the fields of Image Analysis and MMOD impacts. This paper documents our initial research in training an AI DL model using the fast-AI library to identify actual and simulated MMOD impacts and perforations into exposed flat surfaces. While we recognize that this initial goal seems modest, it must be noted that what we have done would have taken teams of individuals and years of training just ten years ago. Our long-term goal is to add complexity and use-cases to the DL model being trained to expand the capabilities of this model so that it can be used to identify MMOD impacts on all types of spacecraft surfaces.

Cameron M Collins↗

Saltstone Oxidation Study: Leaching Method

Cementitious waste forms can be designed to chemically stabilize selected contaminants, such as Tc{sup +7} and Cr{sup +6}, by chemically reduction to lower valance states, Tc{sup +4} and Cr{sup +3}, respectively, and precipitation of these species in alkaline media as low solubility solid phases. Data for oxidation of this type of cementitious waste form cured under field conditions as a function of time is required for predicting the performance of the waste form and disposal facility. The rate of oxidation (oxidation front advancement) is an important parameter for predicting performance because the solubilities of some radionuclide contaminants, e.g., technetium, are a function of the oxidation state. A non-radioactive experiment was designed for quantifying the oxidation front advancement using chromium, as an approximate redox-sensitive surrogate (Cr{sup +6} / Cr{sup +3}) for technetium (Tc{sup +7} / Tc{sup +4}). Nonradioactive cementitious waste forms were prepared in the laboratory and cured under both laboratory and ?field conditions.? Laboratory conditions were ambient temperature and sealed sample containers. Field conditions were approximated by curing samples in open containers which were placed inside a plastic container stored outdoors at SRS. The container had a lid and was instrumented with temperature and humidity probes. Subsamples as thin as 0.2 mm were taken as a function of distance from the exposed surface of the as-cast sample. The subsamples were leached and the leachates were analyzed for chromium, nitrate, nitrite and sodium. Nitrate, nitrite, and sodium concentrations were used to provide baseline data because these species are not chemically retained in the waste form matrix to any significant extent and are not redox sensitive. ?Effective? oxidation fronts for Cr were measured for samples containing 1000, 500 and 20 mg/kg Cr added as soluble sodium chromate, Na{sub 2}CrO{sub 4}. For a sample cured for 129 days under field conditions, leachable Cr (assumed to be the oxidized form, i.e., Cr{sup +6} was detected in the top 15 to 20 mm of the sample spiked with 1000 mg/kg Cr. Below about 20 mm, the Cr concentrations in leachates were below the detection limit (< 0.010 mg/L) which indicates that the oxidation as the result of exposure to air was limited to the top 20 mm of the sample after exposure for 129 days and that the bulk of the waste form was not affected, i.e., the Cr was stabilized and insoluble. For samples cured in the laboratory, leachable Cr was detected in the top 8 mm of the Cr 1000 sample cured in the laboratory for 37 days. Between 8 and 14 mm, the concentration Cr in the leachate dropped by a factor of about 20 to just above the detection limit. These depth of penetration results indicate that the rate of advancement of the oxidation front for samples spiked with 1000 mg/kg Cr cured under ?field conditions? for 129 days is less than that for the sample cured in the laboratory for 37 days, i.e., 0.156 and 0.216 mm/day, respectively. Additional data are presented for samples spiked with 500 and 20 mg/kg Cr. In summary, cementitious waste forms are porous solids with a network of interconnected pores ranging in diameter from 10E-10 m to greater than a few mm. The oxidation process is assumed to occur as the result of oxygen transport through the interconnected porosity which may be filled with air, aqueous salt solution, or both. Upon oxidation, the Cr becomes soluble and can be transported in solution through aqueous pore fluid or leachate.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Fuel nozzle having respective arrays of pre-mixing conduits with respective vortex generators

A fuel nozzle including vortex generating features for use in a combustion turbine engine is provided. An array of inner pre-mixing conduits (20) extends between an inlet end (14) and an outlet end (16) of the nozzle. An array of outer pre-mixing conduits (22) may be disposed radially outwardly relative to the inner pre-mixing conduits (20). A fuel-directing tube (24) includes fuel-directing arms (26) structured to direct fuel flow into the outer pre-mixing conduits (22) to be mixed with a flow of air. The fuel-directing arms include a bluff structural arrangement (30) that may be disposed upstream of fuel injection locations (32, 32') into the outer pre-mixing conduits (22). The proposed nozzle is believed to provide superior micro-mixing capability, such as by increasing the depth of penetration of jets of fuel in a cross-flow of air, and/or formation of vortices in a wake zone downstream from the vortex generating features.

Meadows, Joseph↗

Thermal Charging Rate of Composite Wax-Expanded Graphite Phase Change Materials

Phase change materials (PCMs) are valuable for their ability to store heat nearly isothermally around their phase transition temperature. PCMs are at the core of latent heat thermal energy storage (LHTES) systems, which provide the ability to buffer high thermal loads or decouple the time when heating or cooling is needed from when it is produced. Thermal charging and discharging of LHTES systems often employ a constant temperature source, and the rate at which heat can be exchanged is dependent on the thermophysical properties of the PCM. For graphite composite PCMs, the high thermal conductivity of the graphite enables an increased heat transfer rate through the material, but its presence displaces PCM which reduces the effective volumetric latent heat of the composite relative to the pure PCM. This results in a tradeoff between thermal power and volumetric energy storage capacity. The thermal charging rate is the average thermal energy stored in the material for some elapsed time. In this study, composite PCMs of compressed expanded natural graphite (CENG) and n-Octadecane are studied. Samples with varying CENG mass fractions were synthesized and the thermal charging rate was measured under a constant temperature boundary condition. For evaluation of the expanded graphite-PCM composite, one boundary of the material was exposed to a 50°C constant temperature plate, above the 27.5°C melting temperature of the PCM. The melting front progression [mm-s-1] and the thermal charging rate [W-cm-2] of the PCM were determined, and the results were compared with analytical predictions for the 1-D semi-infinite phase change. For CENG addition up to 5.75% mass fraction, a 450% thermal conductivity increase was observed with a 5% decrease in volumetric energy density as compared to pure octadecane. The average thermal charging rate was increased by over 430% for the melt to penetrate a depth of 22 mm. The experimental results matched analytical predictions, indicating that higher CENG fractions can be evaluated using analytical approaches.

Hirschey, Jason↗

Salt-stone Oxidation Study: Leaching Method - 13092

Cementitious waste forms can be designed to chemically stabilize selected contaminants, such as Tc{sup +7} and Cr{sup +6}, by chemically reduction to lower valance states, Tc{sup +4} and Cr{sup +3}, respectively, and precipitation of these species in alkaline media as low solubility solid phases. Data for oxidation of this type of cementitious waste form cured under field conditions as a function of time is required for predicting the performance of the waste form and disposal facility. The rate of oxidation (oxidation front advancement) is an important parameter for predicting performance because the solubilities of some radionuclide contaminants, e.g., technetium, are a function of the oxidation state. A non-radioactive experiment was designed for quantifying the oxidation front advancement using chromium, as an approximate redox-sensitive surrogate (Cr{sup +6} / Cr{sup +3}) for technetium (Tc{sup +7} / Tc{sup +4}). Nonradioactive cementitious waste forms were prepared in the laboratory and cured under both laboratory and 'field conditions'. Laboratory conditions were ambient temperature and sealed sample containers. Field conditions were approximated by curing samples in open containers which were placed inside a plastic container stored outdoors at SRS. The container had a lid and was instrumented with temperature and humidity probes. Sub-samples as thin as 0.2 mm were taken as a function of distance from the exposed surface of the as-cast sample. The sub-samples were leached and the leachates were analyzed for chromium, nitrate, nitrite and sodium. Nitrate, nitrite, and sodium concentrations were used to provide baseline data because these species are not chemically retained in the waste form matrix to any significant extent and are not redox sensitive. 'Effective' oxidation fronts for Cr were measured for samples containing 1000, 500 and 20 mg/kg Cr added as soluble sodium chromate, Na{sub 2}CrO{sub 4}. For a sample cured for 129 days under field conditions, leachable Cr (assumed to be the oxidized form, i.e., Cr{sup +6} was detected in the top 15 to 20 mm of the sample spiked with 1000 mg/kg Cr. Below about 20 mm, the Cr concentrations in leachates were below the detection limit (< 0.010 mg/L) which indicates that the oxidation as the result of exposure to air was limited to the top 20 mm of the sample after exposure for 129 days and that the bulk of the waste form was not affected, i.e., the Cr was stabilized and insoluble. For samples cured in the laboratory, leachable Cr was detected in the top 8 mm of the Cr 1000 sample cured in the laboratory for 37 days. Between 8 and 14 mm, the concentration Cr in the leachate dropped by a factor of about 20 to just above the detection limit. These depth of penetration results indicate that the rate of advancement of the oxidation front for samples spiked with 1000 mg/kg Cr cured under 'field conditions' for 129 days is less than that for the sample cured in the laboratory for 37 days, i.e., 0.156 and 0.216 mm/day, respectively. Additional data are presented for samples spiked with 500 and 20 mg/kg Cr. In summary, cementitious waste forms are porous solids with a network of interconnected pores ranging in diameter from 10 E-10 m to greater than a few mm. The oxidation process is assumed to occur as the result of oxygen transport through the interconnected porosity which may be filled with air, aqueous salt solution, or both. Upon oxidation, the Cr becomes soluble and can be transported in solution through aqueous pore fluid or leachate. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The potential of high-frequency forced pulsed water jet for nuclear decommissioning - 15367

Forced Pulse Water Jetting (FPWJ) has been demonstrated in other works as a credible and consistent method for removing coatings or otherwise preparing surfaces across numerous industries. Its applicability to the nuclear industry as a powerful tool for decommissioning and waste treatment has only recently being recognized and underpinning study is required before any deployment can be considered. Use of FPWJ within the nuclear sector for decommissioning and waste treatment, requires a different degree of surface finish to achieve a decontamination effect or an assured performance. This necessitates a greater erosion of the base metal than in other industries. The addition of a Forced Pulse Modulation Unit (FPMU) to a high pressure water jetting system offers performance shifts akin to the differences between High Pressure (HP) and Ultra High Pressure (UHP) water jets. Trials have been undertaken in a controlled environment to establish the number of cycles to achieve a given mass loss and or depth of penetration that would otherwise provide decontamination of mostly flat or simple geometry surfaces using a robotic arm for consistency and safety. It has also been shown that metalwork can be readily penetrated without risk of explosion, for example to allow draining of a gas cylinder. Most nuclear facilities have a plethora of pipe systems spanning various diameters. A considerable portion of the UK Sellafield site has 2 inch bore pipe. The FPMU technology is being adapted to consider applications in enclosed systems, such as decontamination of pipes. Exploratory works to date show there to be many physical attributes that influence performance that include, standoff of the jet, established propagated forced pulse jet length, interference from resultant water spray and angle of attack. Comparatively small changes to these parameters can have a profound effect on performance. The process is capable of removing 10's microns to several mms of metal progressively and repeatedly. This enables a credible potential treatment of plant and equipment at Intermediate Level Waste and High Level Waste thresholds. In considering this as a treatment method, a balance between performance, cost and environmental impact of effluents must be made and will be studied further during future active trials. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Controlling Force and Depth in Friction Stir Welding

Feedback control of the penetration force applied to a pin tool in friction stir welding has been found to be a robust and reliable means for controlling the depth of penetration of the tool. This discovery has made it possible to simplify depth control and to weld with greater repeatability, even on workpieces with long weld joints. Prior to this discovery, depths of penetration in friction stir welding were controlled by hard-tooled roller assemblies or by depth actuators controlled by feedback from such external sensors as linear variable-differential transformers or laser-based devices. These means of control are limited: A hard-tooled roller assembly confines a pin tool to a preset depth that cannot be changed easily during the welding process. A measurement by an external sensor is only an indirect indicative of the depth of penetration, and computations to correlate such a measurement with a depth of penetration are vulnerable to error. The present force-feedback approach exploits the proportionality between the depth and the force of penetration Unlike a depth measurement taken by an external sensor, a force measurement can be direct because it can be taken by a sensor coupled directly to the pin tool. The reading can be processed through a modern electronic servo control system to control an actuator to keep the applied penetration force at the desired level. In comparison with the older depth-control methods described above, this method offers greater sensitivity to plasticizing of the workpiece metal and is less sensitive to process noise, resulting in a more consistent process. In an experiment, a tapered panel was friction stir welded while controlling the force of penetration according to this method. The figure is a plot of measurements taken during the experiment, showing that force was controlled with a variation of 200 lb (890 N), resulting in control of the depth of penetration with a variation of 0.004 in. (0.1 mm).

Adams, Glynn↗

Tracking ocean heat uptake during the surface warming hiatus

Ocean heat uptake is observed to penetrate deep during the recent hiatus1,2,3 of global warming in the Atlantic and Southern Ocean. This has been suggested to indicate that the two regions are the driver of the surface warming hiatus4. We show that the deep heat penetration in the Atlantic and Southern Ocean is not unique to the hiatus but common to the past four decades including the 1970s-90s epoch of accelerated surface warming. Our analyses of a large ensemble simulation5 confirm the deep heat penetration in the Atlantic and Southern Ocean in ensemble members with or without surface warming hiatus in the early 21th century. During the past four decades, the global ocean heat content (OHC) of upper 1500m is dominated by a warming trend, and the depth of anthropogenic heat penetration merely reflects the depth of the mean meridional overturning circulation in the basin. Furthermore, the heat penetration depth is not a valid basis to infer the hiatus mechanism.

58 GEOSCIENCES↗

Lithospheric stresses due to radiogenic heating of an ice-silicate planetary body - Implications for Ganymede's tectonic evolution

Thermal evolution models of differentiated and undifferentiated ice-silicate bodies containing long-lived radiogenic heat sources are examined. Lithospheric sresses arise due to volume change of the interior and temperature change in the lithosphere. For an undifferentiated body, the surface stress peaks early in the evolution, while in the differentiated case, stresses peak later and continue to accumulate for longer periods of time. The variation of near-surface stress with depth shows that stresses for the undifferentiated body initially penetrate to great depths, but rapidly concentrate within a few kilometers of the surface. For the differentiated body, elastic stresses never accumulate at a depth greater than a few kilometers. These models are applied to consider long-term rdioactive heating as a possible mechanism of tectonic activity and bright terrain formation on Ganymede.

Zuber, M. T.↗

INTER-DIGITAL CAPACITIVE SENSOR FOR EVALUATING CABLE INSULATION THROUGH JACKET

Interdigital capacitive (IDC) sensors have previously been used to measure cable-age/damage indicative dielectric properties of cable insulation when placed in direct contact with the insulation. Often cable insulation is covered by a polymer jacket precluding direct contact with the insulation. As part of a continuing program to develop and evaluate nondestructive examination methods that may be applied to cable condition assessment, an IDC to measure the effect of cable polymer dielectric change through a covering jacket has been developed. The IDC consists of two fork-like electrodes facing each other with the fork tines interspersed and separated by a small gap. On one electrode, the gap is 5 mm while on the other, the gap is 2 mm. Electric field depth-of-field penetrations are similar to the electrode gaps. The electrodes are printed on a flexible substrate that can be conformed to the outside jacketed surface of a cylindrical cable, with tines parallel to the cable axis. The electrodes are connected to a broad frequency-spectral impedance meter that senses the capacitance between the narrowly gapped electrode tines. This capacitance is known to vary as a function of the permittivity of any material in close proximity to the electrodes. For jacketed cable systems, the IDC response is dominated by the jacket but, by analyzing measurements from IDC sensors with different depths-of-field penetration into the cable under test, the influence of the cable jacket material (primarily influenced by the shallow-depth-of field IDC) can be separated from the deeper-depth-of-field IDC sensing the combined effects of both jacket and underlying insulation. No other NDE method is known that is capable of sensing insulation dielectric properties through an overlying jacket.

Cable NDE, Interdigital Capacitance, Insulation Pe↗

Slag Penetration into Refractory Lining of Slagging Coal Gasifier

The impurities in coal are converted into molten slag typically containing SiO2, FeO, CaO, and Al2O3 when coal feedstock is burned in slagging gasifiers. The slag flows down the gasifier sidewalls, dissolves, and penetrates and reacts with the refractory lining that protects the stainless steel shell of the gasifier from elevated temperatures (1300–1600°C). Refractories composed primarily of Cr2O3 have been found most resistant to slag corrosion, but they continue to fail performance requirements because of low resistance to spalling. Post-mortem analysis of high-chromia refractory bricks collected from commercial gasifiers suggests that the spalling is affected by the depth of slag penetration that is in turn affected by the wettability and interconnected porosity of the refractory as well as the slag viscosity. Laboratory tests were conducted to measure the viscosity of slags (Wyoming Powder River Basin [PRB], Pocahontas #3, and Pittsburgh #8), their contact angle on refractories (chromia-alumina [Aurex 75SR] and high-chromia [Serv 95 and Aurex 95P]), and the apparent porosity of selected refractories. In addition, the depth of slag penetration as a function of time and temperature was determined for various refractory-slag combinations. The results of laboratory tests were used to develop a refractory material that has high resistance to penetration by molten slag and thus has a potential to have a substantially longer service life than the materials currently being used.

01 COAL, LIGNITE, AND PEAT↗

Packing properties of fine powders and the depth of the lunar dust layer

Previous experimental and theoretical studies by Hapke and Van Horn [1963] and Hapke [1963] of surfaces which reflect light like the moon support the hypothesis that the lunar surface is covered with a layer of fine rock dust. The material in this layer appears to be in an extremely unconsolidated state, having a bulk density of the order of one-eighth that of solid rock. Such photometric studies can give information concerning only the upper few millimeters of the lunar soil. However, analyses of radiofrequency observations indicate that extensive areas of the moon may be covered to depths of the order of a meter or greater by a substance which is also much less dense than solid rock. From the radar reflectivity of the lunar surface at meter wavelengths Evans [1962] infers a dielectric constant of K = 2.7; Troitsky [1962] estimates K = 1.6 on the basis of radio-thermal observations at centimeter wavelengths. Since the RF dielectric constants of stony meteorites and of terrestrial rocks range from about 4 to 45 [Fensler et al., 1962] it is clear that the density of the lunar soil is unusually low at least to depths to which RF radiation can penetrate; Troitsky estimates this depth to be of the order of 20 wavelengths or greater in the 3-cm-wavelength range.

Powder↗

Shuttle Imaging Radar - Physical controls on signal penetration and subsurface scattering in the Eastern Sahara

Interpretation of Shuttle Imaging Radar-A (SIR-A) images by McCauley et al. (1982) dramatically changed previous concepts of the role that fluvial processes have played over the past 10,000 to 30 million years in shaping this now extremely flat, featureless, and hyperarid landscape. In the present paper, the near-surface stratigraphy, the electrical properties of materials, and the types of radar interfaces found to be responsible for different classes of SIR-A tonal response are summarized. The dominant factors related to efficient microwave signal penetration into the sediment blanket include (1) favorable distribution of particle sizes, (2) extremely low moisture content and (3) reduced geometric scattering at the SIR-A frequency (1.3 GHz). The depth of signal penetration that results in a recorded backscatter, here called 'radar imaging depth', was documented in the field to be a maximum of 1.5 m, or 0.25 of the calculated 'skin depth', for the sediment blanket. Radar imaging depth is estimated to be between 2 and 3 m for active sand dune materials. Diverse permittivity interfaces and volume scatterers within the shallow subsurface are responsible for most of the observed backscatter not directly attributable to grazing outcrops. Calcium carbonate nodules and rhizoliths concentrated in sandy alluvium of Pleistocene age south of Safsaf oasis in south Egypt provide effective contrast in premittivity and thus act as volume scatterers that enhance SIR-A portrayal of younger inset stream channels.

Schaber, G. G.↗

Improved oxidation resistance of organic/inorganic composite atomic layer deposition coated cellulose nanocrystal aerogels

Cellulose nanocrystal (CNC) aerogels are coated with thin conformal layers of Al{sub 2}O{sub 3} using atomic layer deposition to form hybrid organic/inorganic nanocomposites. Electron probe microanalysis and scanning electron microscopy analysis indicated the Al{sub 2}O{sub 3} penetrated more than 1500 μm into the aerogel for extended precursor pulse and exposure/purge times. The measured profile of coated fiber radius versus depth from the aerogel surface agrees well with simulations of precursor penetration depth in modeled aerogel structures. Thermogravimetric analysis shows that Al{sub 2}O{sub 3} coated CNC aerogel nanocomposites do not show significant thermal degradation below 295 °C as compared with 175 °C for uncoated CNC aerogels, an improvement of over 100 °C.

36 MATERIALS SCIENCE↗

SU-E-T-539: Maximum Energy of Helium and Carbon Ions Clinically Needed for Spine, Lung, Prostate and Pancreas Cancer

Purpose: Maximum available kinetic energy of accelerated heavy ions is a critical parameter to consider during the establishment of a heavy ion therapy center. It dictates the maximum range in tissue and determines the size and cost of ion gantry. We have started planning our heavy ion therapy center and we report on the needed ion range. Methods: We analyzed 50 of random SBRT-spine, SBRT- lung, prostate and pancreatic cancer patients from our photon clinic. In the isocentric axial CT cut we recorded the maximum water equivalent depth (WED4Field) of PTV’s most distal edge in four cardinal directions and also in a beam direction that required the largest penetration, WEDGantry. These depths were then used to calculate the percentage of our patients we would be able to treat as a function of available maximum carbon and helium beam energy. Based on the Anterior-Posterior WED for lung patients and the maximum available ion energy we estimated the largest possible non-coplanar beam entry angle φ (deviation from vertical) in the isocentric vertical sagittal plane. Results: We found that if 430MeV/u C-12, equivalently 220MeV/u He-4, beams are available, more than 96% (98%) of all patients can be treated without any gantry restrictions (in cardinals angles only) respectively. If the energy is reduced to 400MeV/u C-12, equivalently 205MeV/u He-4, the above fractions reduce to 80% (87%) for prostate and 88% (97%) for other sites. This 7% energy decrease translates to almost 5% gantry size and cost decrease for both ions. These energy limits in combination with the WED in the AP direction for lung patients resulted in average non-coplanar angles of φ430MeV/u = 68°±8° and φ400MeV/u = 65°±10° if nozzle clearance permits them. Conclusion: We found that the two worldwide most common maximum carbon beam energies will treat above 80% of all our patients.

62 RADIOLOGY AND NUCLEAR MEDICINE↗