Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PELLETING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Determination of water equivalent content in fuel rods

In water-cooled reactors, hydriding failure of zircaloy cladding tubes can be easily caused by high content of total water in fuel rods. WEC, which is the water equivalent content within the cold space of a fuel rod, directly reflects the total water content of the fuel rod. A device measuring WEC has been designed, manufactured and tested. This extraction device is a hermetically sealed system consisting of six parts: the break-off part, the heating unit, the reduction unit, the sample storage part, the collecting unit and the gas flow system. Each part is connected to another one using a special connection, and the device's end part is connected to a gas chromatograph. The determination procedure can be briefly summarized as follows: first, a test fuel rod should be put into the sealed device after lathing two circular grooves on both ends, so that it can be easily broken at these points in the break-off part. Driven by carrier gas, water and hydrogen both contained in helium gas and absorbed on the rod in-wall pass over the hot uranium filament where water is converted into hydrogen. After being concentrated by the collecting unit, hydrogen flows into the gas chromatograph for measurement and data are calculated as total water content A. UO{sub 2} pellets in the test rod should be taken out from the sample storage part and the total hydrogen content of these pellets is determined according to ASTM C1457 standard, followed by its conversion into total water content B. Finally, the sum of A and B being divided by the free volume of the cold space within the test rod, gives the value of WEC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Study of the U{sub 3}O{sub 8} effect on MOX fuel sintering mechanisms

The manufacturing of uranium-plutonium mixed oxides fuel (also known as MOX) for light water reactor (LWR), starting generally from UO{sub 2} and PuO{sub 2} raw powders and resulting in (U,Pu)O{sub 2} pellets, involves several steps: i) preparation of a UO{sub 2}+PuO{sub 2} master blend with a Pu content of about 25-30 at% by milling and sieving, ii) dilution by mixing the master blend with non-milled UO{sub 2} to reach a Pu content of about 10 at%, iii) pressing and iv) sintering under Ar / 4 % H{sub 2} + H{sub 2}O gas mixture. In this paper, triuranium octoxide (U{sub 3}O{sub 8}) is used as an additional raw powder in the LWR MOX fuel manufacturing. One of the objectives of this work is to understand the sintering behavior of U{sub 3}O{sub 8} under Ar / 4 % H{sub 2} + H{sub 2}O gas mixture and its effect when added to a UO{sub 2}-PuO{sub 2} mixture. A special attention is given on U{sub 3}O{sub 8} reduction, phase transitions, redox reactions and oxygen partial pressure (pO{sub 2}) evolution during shrinkage: the impact of these phenomena on the densification kinetics is discussed, especially the de-densification phenomenon which could occur at high temperature. For that purpose a specific dilatometer, coupled with a zirconia probe implemented at furnace inlet and outlet has been used which allows following continuously and simultaneously the fuel shrinkage and the oxygen partial pressure variation as a function of temperature. The experiments have shown that, contrary to UO{sub 2}, the sintering of milled PuO{sub 2} is accompanied by a de-densification at high temperature. This de-densification phenomenon already occurs with co-milled 71 at% UO{sub 2} + 29 at% PuO{sub 2}, but with a smaller magnitude. When pure milled U{sub 3}O{sub 8} is sintered, no de-densification phenomenon is observed but the low density of the sintered pellet could hide such a phenomenon. The incorporation of U{sub 3}O{sub 8} into a UO{sub 2}-PuO{sub 2} master blend containing 29 at% of plutonium leads to an exacerbation of the de-densification phenomenon with a higher loss on ignition suggesting that U{sub 3}O{sub 8} contributes also to the de-densification phenomenon. This could be due to high temperature reactions involving the initial carbon content of the raw U{sub 3}O{sub 8} powder. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Studying fuel failure behaviour with a micromechanical approach

Under Loss Of Coolant Accident (LOCA) conditions in light water reactors, the temperature evolution within the fuel pellets combined with a reduction of the cladding confinement can lead to fuel fragmentation. This work focuses on the pellet rim, where bubbles density increases owing to a higher irradiation level. This area, called 'High Burn-up Structure' (HBS), has a specific behaviour due to a microstructure reorganization composed of small grains about 100 nm compared to 10 μm for initial UO{sub 2} fuel. The aim of this study is to define a macroscopic fragmentation model based on a micro mechanical approach to have a better understanding of the fuel mechanical behaviour at lower scale: size and volume fraction of fragments. This paper introduces a stepwise micromechanical method: firstly, we detail how to model the HBS microstructure including pressurized porosities, based on experimental or numerical data and define a Representative Volume Element (RVE). Then we use 3D full field computations in order to determine crack snapshot. Elastic computations are performed to find the bubbles pressure level which is required to reach the cracks initiation threshold. Then nonlinear computations, using a failure local behavior law, are conducted to identify the failure snapshot. The results of these nonlinear computations will be used as an input data of the homogenization ('macroscopic') model. First computations with Full-Fields FEM method give promising results at local scale. Nevertheless, material parameters need to be refined as their experimental values are not perfectly defined yet, leaving an uncertainty in the model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-irradiation examination to assess performance and safety of nuclear fuel

This work presents some results from testing campaigns performed at JRC-ITU on irradiated fuels and analogues aimed at characterizing fuel alterations during and after irradiation. The characterization of local structural and property changes is the first step towards the description of the overall behaviour of the fuel, including safety- and performance-relevant properties. High burnup light water reactor (LWR) UO{sub 2} fuel (= 60 GWd/tHM) was used for morphology and mechanical property studies. Radial profiles of porosity obtained from scanning electron microscopy image analysis were compared with corresponding sub-surface data obtained using acoustic microscopy. An increase of porosity was observed at the rim of the pellet in correspondence with the high burnup structure (HBS), and also at intermediate radius locations in correspondence with the occurrence of the so-called dark zone. This zone is characterized by several features similar to the HBS: in addition to increased local porosity, grain subdivision features were observed. The examination of grain free surface morphology along the pellet radius revealed the onset of surface alteration which resulted in almost complete loss of the original grain shape in conjunction with the formation of the dark zone. Additionally, possible ageing effects due to accumulation of microstructural decay damage during storage were investigated and compared to the results obtained under accelerated ageing conditions using alpha-doped analogues. Similar hardening trends were observed by comparing the hardness evolution as a function of accumulated damaged in unirradiated analogues and spent fuel. No significant hardness increase was observed on the same high burnup/high dose spent fuel after >10 years of additional storage in hot cell, confirming that hardening saturates at a damage level near 0.1 dpa. These experimental campaigns contribute establishing a basis of data for further analysis, in combination with suitable modelling tools. The final goal is to achieve the full scientific understanding of mechanisms and processes affecting fuel properties and behaviour, as a necessary step to establish the basis for developing advanced fuel systems with optimized performance and safety. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Simulation of fission gas diffusion in UO{sub 2} by vacancy clusters

The low solubility of fission gas in nuclear fuel leads to inter- and intra-granular bubbles. These bubbles affect performance of the fuel rod and increase the fuel temperature through the increase of porosity in the fuel pellets and decreased thermal conductivity across the pellet-clad gap as gas is released into the plenum. The nucleation, growth, and inter-connectivity of the fission gas bubbles ultimately depend on the diffusivity of gas atoms through the fuel matrix. Using mechanisms and data previously established from density functional theory (DFT) and empirical potential calculations, diffusion and reaction models have been derived for xenon atoms, uranium atoms, and vacancies in the substitutional and interstitial locations. Although similar to previous models, the diffusion and reaction rates have been re-derived in a more robust manner. Previous studies have under-predicted the experimentally observed diffusivity of xenon atoms in UO{sub 2}, however it has been previously shown that by including xenon atoms bound to two vacancies, the calculated diffusivity approaches the measured data. The derived model for species diffusion and inter-species reactions has been implemented in the MARMOT phase-field code in a modular structure so as to capture the enhanced diffusion of xenon due to bound gas + vacancy-cluster movement. The MARMOT code allows for the diffusion, reaction, and source rates to be solved simultaneously, resulting in steady state or transient concentrations of each species, and ultimately the diffusion behavior of xenon atoms. By including the diffusion of clusters of different combinations of xenon and vacancies, the calculated diffusivity more closely captures the measured diffusivity of xenon when using preliminary parameters. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Neutronics analysis of fuel-in-fiber concept

One of the consequences of Fukushima was the increase in interest in development of safer, more accident tolerant fuels and claddings. Accident tolerant fuels (ATF) are defined by the Nuclear Regulatory Committee (NRC) as fuels that, in comparison with the standard UO{sub 2}- Zircaloy system, can tolerate loss of active cooling in the core for a considerably longer time period while maintaining or improving the fuel performance during normal operations. One of the ideas being considered is tri-isotropic (TRISO) fuel particles. TRISO fuel pebbles consist of several layers - the outermost being graphite. TRISO pebbles are considered to be accident tolerant, because of their ability to retain fission products at high temperatures. One of the ideas implementing TRISO pebbles is Fully Ceramic Microencapsulated fuel where the pellet is comprised of TRISO pebbles in a matrix. TRISO particles though have a low maximum packing fraction when put in the spherical or cylindrical configuration with the current fabrication techniques (hot and cold press). This leads to considerable increase in enrichment to maintain cycle length for today's Light Water Reactors (LWR). The Fuel-in-Fiber concept, developed by FreeForm-Fiber (FFF), has the advantages of TRISO particles while utilizing a novel additive direct manufacturing technique for rapid fabrication. Fuel-in-Fiber are small fibers made of layers just like TRISO particles but because of their cylindrical nature, they can be packed with a tighter packing fraction than the TRISO particles. The fibers are woven within a SiC matrix and used to replace a typical pellet in a fuel pin. This means that they can easily be placed into LWR's without having to change the assembly or core structures. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Modulation of Tetravalent Actinide Oxalate Morphology through Organic Compounds

Spent nuclear fuel of pressurized water reactors mainly consists of uranium, plutonium, minor actinides and fission products. The long term radiotoxicity of wastes is mainly due to plutonium and minor actinides such as neptunium, americium and curium. So, in order both to reduce the radiotoxicity of the ultimate wastes and to save uranium resources, researches for current and new generations of nuclear plants focus on the recycling of plutonium and minor actinides, to fabricate new mixed oxides nuclear fuel pellets (MOX) or transmutation targets. In this aim, production of actinide oxides is necessary. Currently, according to the Purex process, the spent fuel is dissolved in nitric acid and then valuable actinides (uranium and plutonium) are separated and purified from fission products and minor actinides in the Areva plant 'La Hague'. The resulting plutonium nitric solution is converted into a solid phase by oxalic conversion: the oxalic precipitation is followed by the calcination of the obtained oxalate into plutonium oxide. Considering either the MOX fuel or the transmutation targets fabrication from actinide oxides, the control of the particle structure and microstructure is a key factor related to the ability of oxide powder to sinter and shape as pellets. In the oxalic conversion process, the morphology of the precipitated oxalate is strongly influenced by the precipitation conditions and is kept during the calcination from oxalate into oxide. In this context, the aim of this work is to control the morphology of the final actinide oxide by changing the oxalic precipitation conditions. A lot of possibilities can be considered to modulate the morphology of actinide oxalates. Numerous parameters such as temperature, pressure, the presence of a magnetic field, the operating process (seeding, emulsions)... can modify the precipitated particles shape. Additives are also able to play a major role at the precipitation stage by means of different mechanisms involving either complexation, surface covering or structure insertion. This study focuses on this way to modify the morphology of actinides oxalates.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-Irradiation Examination for Conventional and Advanced Nuclear Fuel

During irradiation in a nuclear reactor, the fuel pellet experiences non-uniform fission rate and strong thermomechanical loads, which result in alterations and restructuring occurring non-homogeneously in the fuel volume. The irradiated fuel is characterized by a highly heterogeneous structure, with a correspondingly heterogeneous distribution of phases and properties. It is a big technical challenge for a hot cell facility to be able to cover effectively a broad variety of fuel types and compounds, characterized by different compositions, physico-chemical properties, geometries and configurations. The first challenge is to provide testing environments and procedures which do not alter or degrade the original irradiated fuel properties and are technically suitable for hot cell or shielded facility operation. For instance, non-oxide fuel compounds require protective atmosphere to avoid sample oxidation during storage, preparation and testing. Moreover, suitable adaptations of tools and measuring devices must be available to characterize fuel configurations which differ from the conventional cylindrical pellet-cladding geometries (e.g. spherical fuel elements for pebble bed HTR and TRISO coated fuel particles). Finally, adequate scientific methods of investigation must be available to measure properties and study the behaviour of highly heterogeneous irradiated fuel. In addition to basic techniques for non-destructive and destructive examination of nuclear fuel systems (e.g. covering fuel and cladding or fuel and coatings, or other configurations), 'in-depth' methods are applied to determine physical, thermomechanical and micro-analytical properties of specific phases/features present in irradiated fuel. This paper presents relevant trends and examples from fuel safety studies performed at JRC-Karlsruhe and in other laboratories which highlight the 'added value' obtainable by applying combined techniques, high resolution tools or 3D methods of analysis for the experimental 'multiscale' characterization of irradiated fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of a potassium filled UO{sub 2} core in a beryllium-reflected space reactor - 14371

The critical configuration of the small, compact critical assembly (SCCA) experiments performed at the Oak Ridge Critical Experiments Facility (ORCEF) in 1962-1965[1,2] have been evaluated for the International Criticality Safety Benchmark Evaluation Project (ICSBEP) and were determined to be acceptable benchmark experiments and are included in the International Handbook of Evaluated Criticality Safety Benchmark Experiments (ICSBEP Handbook)[3]. The initial intent of these experiments was to support the design of the Medium Power Reactor Experiment (MPRE) program, whose purpose was to study 'power plants for the production of electrical power in space vehicles'.[4] The third configuration in this series of experiments was a beryllium-reflected mockup of a stainless-steel-clad, highly enriched uranium (HEU)-O{sub 2} fuel, potassium-cooled, space power reactor. Reactivity measurements, cadmium ratio spectral measurements, and fission rate measurements were measured through the core and top reflector. Fuel effect worth measurements and neutron moderating and absorbing material worths were also measured in the assembly fuel region. The cadmium ratios, fission rate, and worth measurements were evaluated for the International Reactor Physics Experiment Evaluation Project (IRPhEP) and are published in the International Handbook of Evaluated Reactor Physics Benchmark Experiments (IRPhEP Handbook)[5]. More recently, two additional critical configurations have been evaluated and added to the existing evaluation report in the ICSBEP Handbook. The new critical configurations measure the effect of filling the core with potassium. The critical configuration consisted of 30.48 cm tall fuel tubes of 93.15 wt.% enriched uranium dioxide (UO{sub 2}) pellets. Each fuel tube had 26 pellets with a total mass of 295.8 g UO{sub 2} per tube. There were 253 tubes were arranged with 1.506-cm center-to-center, triangular spacing and surrounded on all side by a beryllium reflected. The reactivity of the system was measured with the core tank empty and filled with potassium. The system reactivity was increased from 13.4 c to 32 c. This change in system reactivity represents the worth of the potassium. Simple benchmark models for the empty and potassium filled cores have been derived and evaluated and found to be acceptable as benchmark experiments. The benchmark experiment eigenvalues are 1.0001 ± 0.0008 and 1.0011 ± 0.0009 for the empty and filled cores, respectively. When calculated with MCNP5 and ENDF/B-VII.0 the calculated eigenvalues are 0.98906 ± 0.00002 and 0.98883 ± 0.00002, respectively. These results are concerning due to the drop of the calculated system reactivity when potassium is added to the system rather than the expected increase in system reactivity. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

OECD/NEA MPCMIV Benchmark - Preliminary fuel performance results

The on-going OECD/NEA Multi-physics Pellet Cladding Mechanical Interaction Validation (MPCMIV) benchmark aims to provide guidance on multi-physics validation through the modelling of two cold ramps. In this paper, the first results for the base irradiation of the father rod and fuel rodlet (refabricated from the father rod), and the first cold ramp are presented. The base irradiation consists of 3 years of irradiation in the Forsmark-2 reactor. The cold ramp encompasses a steady-state pre-ramp period of less than one hour at a low constant linear heat rate (LHR) followed by a ramp test (< 1 min) with a much higher maximal LHR. The base irradiation is modelled using the fuel performance codes FRAPCON and FAST, while the cold ramp modeling is using the fuel performance code FRAPTRAN. Several missing parameters for FRAPCON/FAST base irradiation models have been selected using multiple references such as the OECD/NEA light water reactor Uncertainty Analysis in Modelling (UAM) benchmark specifications and the FRAPCON Integral Assessment report. The obtained results for the base irradiation such as the cladding outer diameter show reasonable agreement with the experimental measurements. The results for the cold ramp show larger differences with the experimental measurements (e.g., cladding axial elongation). However, such differences have been observed as well in other studies involving pellet cladding mechanical interaction analyses and are attributed to the fuel performance modelling assumptions and to the tuned modelling parameters that were not covered by the specifications. Uncertainty and sensitivity analysis might allow a better quantification of these missing parameters. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

The Origins of the Rate Enhancement in LiNi0.4Co0.2-yAlyMn0.4O2 (0<y<_0.2) Cathode Materials

Recently, much research has been directed towards finding a replacement cathode material for LiCoO{sub 2} combining high performance with lower cost and toxicity. One promising candidate material is the mixed transition metal oxide LiNi{sub 0.4}Co{sub 0.2}Mn{sub 0.4}O{sub 2}, which delivers 180 mAh/g below 4.4 V versus Li/Li{sup +} (1, 2). However, in this material, there is 4% anti-site cation mixing, which hinders the mobility of lithium within the lattice, adversely affecting its rate performance in lithium batteries. Ongoing work in our lab has shown that partial or full substitution of cobalt with aluminum, LiNi{sub 0.4}Co{sub 0.2}Mn{sub 0.4}O{sub 2} (0 < y {le} 0.2), can lead to significant improvements in rate performance (3). In particular, LiNi{sub 0.4}Co{sub 0.2}Mn{sub 0.4}O{sub 2} shows greatly improved rate capability with almost no sacrifice in the overall capacity delivered at low rates between 2.0 and 4.3V (Figure 1). The smaller ionic radius of Al{sup 3+} in octahedral coordination (0.535 {angstrom}) compared to Li{sup +} (0.76 {angstrom}) creates a strong driving force for the formation of a more lamellar structure in the aluminum containing materials (4, 5). XRD experiments and subsequent Rietveld refinement (Figure 2) reveal a significant decrease in anti-site defect concentration upon aluminum substitution, dropping from {approx}4% at y=0 to {approx}2.5% at y=0.2. Concurrently, there is an increase in the lithium slab dimension from 2.6 {angstrom} to 2.63 {angstrom}. This expansion allows for a reduced activation energy and improved lithium diffusivity through the crystal lattice (6). Interestingly, the pressed pellet conductivities of Al-substituted compounds are lower than that of the parent as determined by AC impedance measurements. This lends further credence to the hypothesis that structural effects resulting in improved lithium diffusivity are responsible for the rate enhancement, rather than changes in the electronic structure. Further experiments to understand the effect of structural changes induced by Al substitution on the transport properties are underway in this laboratory. The changes in electronic conductivity and the chemical diffusion coefficient of lithium as determined by pressed pellet conductivities and GITT experiments will be discussed. Further refinement of cation ordering and crystal structure parameters as determined from neutron diffraction and XANES experiments will also be presented.

25 ENERGY STORAGE↗

The Origins of the Rate Enhancement in LiNi0.4Co0.2-yAlyMn0.4O2 (0<y<_0.2) Cathode Materials

Recently, much research has been directed towards finding a replacement cathode material for LiCoO{sub 2} combining high performance with lower cost and toxicity. One promising candidate material is the mixed transition metal oxide LiNi{sub 0.4}Co{sub 0.2}Mn{sub 0.4}O{sub 2}, which delivers 180 mAh/g below 4.4 V versus Li/Li{sup +}. However, in this material, there is 4% anti-site cation mixing, which hinders the mobility of lithium within the lattice, adversely affecting its rate performance in lithium batteries. Ongoing work in our lab has shown that partial or full substitution of cobalt with aluminum, LiNi{sub 0.4}Co{sub 0.2-y}Al{sub y}Mn{sub 0.4}O{sub 2} (0 < y {le} 0.2), can lead to significant improvements in rate performance. In particular, LiNi{sub 0.4}Co{sub 0.15}Al{sub 0.05}Mn{sub 0.4}O{sub 2} shows greatly improved rate capability with almost no sacrifice in the overall capacity delivered at low rates between 2.0 and 4.3V (Figure 1). The smaller ionic radius of Al{sup 3+} in octahedral coordination (0.535 {angstrom}) compared to Li{sup +} (0.76 {angstrom}) creates a strong driving force for the formation of a more lamellar structure in the aluminum containing materials. XRD experiments and subsequent Rietveld refinement (Figure 2) reveal a significant decrease in anti-site defect concentration upon aluminum substitution, dropping from {approx}4% at y=0 to {approx}2.5% at y=0.2. Concurrently, there is an increase in the lithium slab dimension from 2.6 {angstrom} to 2.63 {angstrom}. This expansion allows for a reduced activation energy and improved lithium diffusivity through the crystal lattice. Interestingly, the pressed pellet conductivities of Al-substituted compounds are lower than that of the parent as determined by AC impedance measurements. This lends further credence to the hypothesis that structural effects resulting in improved lithium diffusivity are responsible for the rate enhancement, rather than changes in the electronic structure. Further experiments to understand the effect of structural changes induced by Al substitution on the transport properties are underway in this laboratory. The changes in electronic conductivity and the chemical diffusion coefficient of lithium as determined by pressed pellet conductivities and GITT experiments will be discussed. Further refinement of cation ordering and crystal structure parameters as determined from neutron diffraction and XANES experiments will also be presented.

25 ENERGY STORAGE↗

Time-resolved studies of particle effects in laser ablation inductively coupled plasma-mass spectrometry

Time resolved signals in laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) are studied to determine the influence of experimental parameters on ICP-induced fractionation effects. Differences in sample composition and morphology, i.e., ablating brass, glass, or dust pellets, have a profound effect on the time resolved signal. Helium transport gas significantly decreases large positive signal spikes arising from large particles in the ICP. A binder for pellets also reduces the abundance and amplitude of spikes in the signal. MO{sup +} ions also yield signal spikes, but these MO{sup +} spikes generally occur at different times from their atomic ion counterparts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A multicriteria approach to evaluate district heating system options

District energy systems, in which renewable energy sources may be utilized, are centralized systems to provide energy to residential and commercial buildings. The aim of this paper is to evaluate and rank energy sources available for a case of district heating system in Vancouver, Canada, based on multiple criteria and the view points of different stakeholders, and to show how communication would affect the ranking of alternatives. The available energy sources are natural gas, biomass (wood pellets), sewer heat, and geothermal heat. The evaluation criteria include GHG emissions, particulate matter emissions, maturity of technology, traffic load, and local source. In order to rank the energy options the PROMETHEE method is used. In this paper, two different scenarios were developed to indicate how the communication between the stakeholders would affect their preferences about criteria weights and would change the ranking of alternatives. The result of this study shows that without communication the best energy source for the considered district energy system is different for different stakeholders. While, addressing concerns through efficient communication would result in a general consensus. In this case, wood pellet is the best energy alternative for all the stakeholders.

03 NATURAL GAS↗

Thermoelectric Properties of Non-equilibrium Synthesized Ce0.9Fe3CoSb12 Filled Skutterudites

The authors report on the thermoelectric properties of the filled skutterudite Ce{sub 0.9}Fe{sub 3}CoSb{sub 12} prepared via non-equilibrium synthesis method. Melt-spun ribbons were directly converting into single phase polycrystalline pellets under pressure. For comparison, pellets with the same composition were also prepared using the conventional solid-state reaction followed by long term annealing. It was found that the non-equilibrium synthesized samples have higher power factors and lower thermal conductivity, leading to substantially higher figure of merit.

36 MATERIALS SCIENCE↗

JV Task 95-Particulate Control Consulting for Minnesota Ore Operations

The purpose of the project was to assist U.S. Steel in the evaluation, selection, planning, design, and testing of potential approaches to help meet U.S. Steel's goal for low-particulate matter emissions and regulatory compliance. The energy-intensive process for producing iron pellets includes treating the pellets in high-temperature kilns in which the iron is converted from magnetite to hematite. The kilns can be fired with either natural gas or a combination of gas and coal or biomass fuel and are equipped with wet venturi scrubbers for particulate control. Particulate measurements at the inlet and outlet of the scrubbers and analysis of size-fractionated particulate samples led to an understanding of the effect of process variables on the measured emissions and an approach to meet regulatory compliance.

01 COAL, LIGNITE, AND PEAT↗

Direct Observation of Interfacial Mechanical Failure in Thiophosphate Solid Electrolytes with Operando X-Ray Tomography

Herein, the mechanical behaviors of Li 10 GeP 2 S 12 (LGPS) solid electrolytes during electrochemical cycling using operando X-ray tomography are investigated. It is demonstrated that the bulk mechanical decomposition of LGPS when cycled against lithium is a direct result of electrochemical reduction of the solid electrolyte at the LGPS/Li 0 interface. The reductive decomposition of LGPS during lithium plating results in the formation of low-density domains at the electrode/electrolyte interface, which impose sufficient mechanical stress on the underlying LGPS to crack the SE pellet. The critical stress developed prior to pellet fracture is significantly lower than the bulk shear modulus of LGPS, suggesting that the electrochemical instability of LGPS dramatically worsens the mechanical stability of the material near the LGPS/Li 0 interface. It is also shown that the application of a highly concentrated liquid electrolyte to the LGPS surface suppresses the reductive decomposition of LGPS, improving both the electrochemical performance and mechanical stability of the bulk LGPS solid electrolyte.

36 MATERIALS SCIENCE↗

The Effect of Mechanical State on the Equilibrium Potential of Alkali Metal/Ceramic Single–Ion Conductor Systems

The relationship between mechanical stress states and interfacial electrochemical thermodynamics of Li metal/Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 and Na metal/ Na-β”-Al 2 O 3 systems are examined in two experimental configurations with an applied uniaxial load; the solid electrolytes are pellets and the metal electrodes high-aspect-ratio electrodes. The experimental results demonstrate that 1) the change in equilibrium potential at the metal/electrolyte interface, when stress is applied to the metal electrode, is linearly proportional to the molar volume of the metal electrode, and 2) the mechanical stress in the electrolyte has a negligible effect on the equilibrium potential for an experimental setup in which the electrolyte is stressed and the electrode is left unstressed. Solid mechanics modeling of a metal electrode on a solid electrolyte pellet indicates that pressure and normal stress are within ≈0.5 MPa of each other for the high aspect ratio (≈1:100 thickness:diameter in our study) Li metal electrodes under loads that exceed yield conditions. Furthermore, this work should aid in advancing the quantitative understanding of alkali metal dendrite formation within incipient cracks and their subsequent growth, and pore formation upon stripping, both situations where properly accounting for the impact of mechanical state on the equilibrium potential is of critical importance for calculating the current distribution.

25 ENERGY STORAGE↗