Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Magnetic source”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Radial Loading of Hydrodynamic Bearings Due to Magnetic Variation

Anomalies during integration of a small-scale hydrodynamic pump motor prompted an investigation into all sources of radial loading on the bearings, and revealed that overall loads were insufficiently characterized. Experimental measurements demonstrated that magnetic forces in the pump motor contributed to significant amounts of radial loading on the bearings, potentially causing wear over long periods of operation and premature failures. The magnitude of these magnetic forces was determined for the rotor and stator separately, as well as for the rotor-stator assembly by designing various experimental setups able to recreate the pump motor without hydrodynamic bearings. Characterization of these magnetic forces led to changes in manufacturing processes and enabled selective choices of components, improving the pump motor hardware in order to meet NASA’s Europa Clipper project requirements.

Underhill, Micheal↗

An analytic formulation for heating source memory in the thermospheric composition

Numerical calculations from a spectral circulation model are utilized to construct an analytic Green's function formulation describing the meridional, time-dependent thermospheric composition and temperature response during magnetic storms. The purpose is to develop a formulation that embodies source memory while being sufficiently simple to serve as a heuristic guide for empirical modeling. By passing from the discrete Fourier series representation, utilized for the numerical circulation model, to a continuous Fourier integral representation, explicit waves are obtained for the thermospheric response times. The response times are altitude and species dependent and can exceed two days below 200 km. Thus, for certain storm scenarios, pronounced source memory signatures for the composition and temperature are predicted. Response times obtained from the formulation are shown to give a response consistent with previously published neutral composition data from AE-C for the February 1974 storm when an ap dependent heat source is employed.

Porter, H. S.↗

Analysis Background & Noise in Stretched Wire Alignment Technique Measurements

The Stretched-Wire Alignment Technique (SWAT) is one method of magnet alignment for linear induction accelerators. The applications of SWAT have been implemented for aligning solenoid magnets on the Scorpius linear induction accelerator which will be sited at the Nevada National Security Site and the Flash X-Ray (FXR) linear induction accelerator at Lawrence Livermore National Laboratory’s Contained Firing Facility. This article describes both systematic (repeatable) and random sources of background and noise as well as practical ways to eliminate or reduce them to acceptable levels. Systematic sources include reflections from wire ends, rapid sag due to ohmic heating of the wire, magnetic materials, and shot rate. Random sources include air currents, vibration of nearby equipment, mechanical stability of test equipment, and the instruments used to measure the wire motion. Mitigations include curve fitting and adaptive noise signal cancellation, and mechanical damping. Finite Element Analysis (FEA) was used to identify and resolve a repeatable wire vibration frequency interfering with the signal resolution. Two stretched wire alignment technique set ups from Sandia National Labs and Lawrence Livermore National Lab have shown background noise sources and ways of mitigating them by either analysis methods or change of mechanical configuration. Conclusions that were drawn included the severe sensitivity of the deflection to even small external interferences of the SWAT wire such that it requires attention to detail in mechanical set up and analysis.

Linear Inductive Accelerator↗

The Bess Investigation of the Origin of Cosmic-ray Antiprotons and Search for Cosmological Antimatter

The Balloon-borne Experiment with a Superconducting Spectrometer (BESS) collaboration has made precise measurements of the spectra of cosmic ray antiprotons and light nuclei and conducted a sensitive search for antinuclei. Ten BESS high-latitude flights, eight from Canada and two from Antarctica, span more than a Solar cycle between 1993 and 2007/2008. BESS measurements of low-energy antiprotons constrain candidate models for dark matter including the possible signature of primordial black hole evaporation. The stringent BESS measurements of antiprotons and the elemental and isotopic spectra of H and He provide strong constraints on models of cosmic-ray transport in the Galaxy and Solar System. BESS has also reported the first antideuterium upper limit. BESS employs a superconducting magnetic-rigity spectrometer with time-of-flight and aerogel Cherenkov detectors to identify incident particles by charge, charge sign, mass, and energy. The BESS-Polar long-duration instrument has reduced lower energy limit of 100 MeV (top of the atmosphere) to increase its sensitivity to possible primary antiproton sources. BESS-Polar II was rebuilt with extended magnet lifetime, improved detector and electronic performance, and greater data storage capacity. It was flown fro Antarctica December 2007-January 2008, recording about 4.6 bission events during 24.5 days at float altitude with the magnet on. During the flight the influence of a high-speed stream in the Solar wind was observed. Details of the BESS-Polar II instrument and flight performance are reported elsewhere at this conference. The successful BESS-Polar II flight at Solar minimum is especially important. Most cosmic-ray antiprotons are secondary products of nuclear interactions of primary cosmic-ray nuclei with the interstellar gas, giving a spectrum that peaks at about 2 GeV and falls rapidly to higher and lower energies. However, BESS data taken in the previous Solar minimum show a small excess over secondary expectations at low energies, possibly suggesting the presence of an additional component that may be masked at higher levels of Solar modulation. The high-statistics Solar minimum data obtained by BESS-Polar II will provide a difinitive test of this component. We will review the BESS program and report the latest results including the antiproton and proton spectra measured in the BESS-Polar I flight, the search for cosmic antinuclei, and the status of the BESS-Polar II analysis.

Mitchell, John↗

Theoretical Investigation of the High-Altitude Cusp Region using Observations from Interball and ISTP Spacecraft

A fundamental goal of magnetospheric physics is to understand the transport of plasma through the solar wind-magnetosphere-ionosphere system. To attain such an understanding, we must determine the sources of the plasma, the trajectories of the particles through the magnetospheric electric and magnetic fields to the point of observation, and the acceleration processes they undergo enroute. This study employed plasma distributions observed in the near-Earth plasma sheet by Interball and Geotail spacecraft together with theoretical techniques to investigate the ion sources and the transport of plasma. We used ion trajectory calculations in magnetic and electric fields from a global Magnetohydrodynamics (MHD) simulation to investigate the transport and to identify common ion sources for ions observed in the near-Earth magnetotail by the Interball and Geotail spacecraft. Our first step was to examine a number of distribution functions and identify distinct boundaries in both configuration and phase space that are indicative of different plasma sources and transport mechanisms. We examined events from October 26, 1995, November 29-30, 1996, and December 22, 1996. During the first event Interball and Geotail were separated by approximately 10 R(sub E) in z, and during the second event the spacecraft were separated by approximately 4(sub RE). Both of these events had a strong IMF By component pointing toward the dawnside. On October 26, 1995, the IMF B(sub Z) component was northward, and on November 1-9-30, 1996, the IMF B sub Z) component was near 0. During the first event, Geotail was located near the equator on the dawn flank, while Interball was for the most part in the lobe region. The distribution function from the Coral instrument on Interball showed less structure and resembled a drifting Maxwellian. The observed distribution on Geotail, on the other hand, included a great number of structures at both low and high energies. During the third event (December 22, 1996) both spacecraft were in the plasma sheet and were separated bY approximately 20 R(sub E) in the y direction. During this event the IMF was southward.

Ashour-Abdalla, Maha↗

Development of photomultiplier electronics and computer interfacing software for a high speed photoelectric photometer-Stoke's meter

Preliminary stages in the design, construction, and development of a photoelectric photometer system interfaced with an IMSAI 8080 microcomputer. The instrument will also include magnetic tape and magnetic disk storage capabilities to enable rapid data storage. The capability of the instrument to make observations with very high time resolution, as high as 10 msec, and measure the intensity and polarization of radiation emitted by objects which show very rapid light variations, pulsars and optical counterparts of X-ray sources was of concern. A better understanding of the magnetic fields and interstellar material which characterize the immediate environment of these stellar systems and an expansion of the observational capabilities of even modest-sized telescopes are expected.

Flesch, T. R.↗

Energetic ion distributions on both sides of the Earth's magnetopause

The Active Magnetospheric Particle Tracer Explorer/Charge Composition Explorer (AMPTE/CCE) spacecraft, with an apogee of approximately 8.8R(sub E) and an inclination of approximately 4.3 deg, sampled the outer dayside equatorial magnetosphere for extended time periods and often crossed into the magnetosheath whenever the solar wind pressure was sufficiently high to compress the magnetopause to less than 8.8R(sub E). We have analyzed ion distributions on both sides of the magnetopause in order to investigate any local time and energy dependence, giving information about physical processes at the magnetopause and the bow shock. Particle measurements are from the Charge Energy Mass (CHEM)(1.5 to 300 keV/e) and Medium-Energy Particle Analyzer (MEPA)(10 keV to 2 MeV) instruments. The wide total energy range (1.5 keV to 2 MeV) covered describes the magnetospheric distributions quite well, and for the purpose of this study, adequately describes the high-energy part of the shocked solar wind. Thus both solar wind and magnetospheric components can be recognized in a mixed particle distribution. Case studies of representative magnetopause crossings at dawn, noon, and dusk, as well as a survey of several other crossings, indicated: (1) a local time and energy dependence of magnetosheath spectra at energies greater than or equal to 50 KeV; spectra were harder at the duskside than at the dawnside and also correlated with magnetospheric activity, (2) constantly much higher intensities in the magnetosphere than in the magnetosheath at energies greater than 10 KeV and an earthward gradient in the subsolar magnetosheath. In addition to the steady state magnetosheath population there exists a burst-type component indicative of a magnetospheric source, and most of the time this is recognized as a flux transfer event. Overall, the results about the origin of the greater than or equal to 50 KeV magnetosheath ions are consistent with the continuous leakage of magnetospheric particles across a tangential discontinuity magnetopause, locally distributed according to magnetospheric drift paths. Magnetic reconnection, although present, should not be a dominant source on average, because it is not continuous in time. Fermi acceleration should not be dominant because it predicts the opposite local time asymmetry, and shock drift acceleration should be a minor contributor at E greater than or equal to 50 keV because of upper-energy cutoff limitations. Our observations also indicate a significant magnetospheric contribution to energies as low as approximately 10 KeV, where the magnetosphere-magnetosheath intensity gradient reverses. However, in orderto examine the relative strength and local time distribution of all possible sources at these energies, a detailed analysis is required.

Paschalidis, N. P↗

Magnetic Velocity Gauges: Effects of Misalignment

Embedded velocity gauges are standardly used at LANL on gas gun experiments of a shock to-detonation transition. The experiments are intended to be one-dimensional with a planar shock driven by the projectile from a gas gun propagating along the axis of the HE cylinder. As disussed by Gustavsen et al. [1999], the accuracy of the gauges depends on the alignment of the directions of shock propagation, magnetic field and the active gauge element. A source of inaccuracies is from tilt or misalignment angle at impact between the projectile surface and the HE surface; typically a few milliradians. This leads to the shock propagating at a slight angle to the axis of the HE cylinder and can affect the shock rise time of the velocity gauges, the time offset between the tracker gauges for the trajectory of the lead shock, and the gauge positions in the direction of propagation. It is important to note that tilt is characterized by 2 parameters; the magnitude of the angle relative to the HE axis and the direction in the plane transverse to the HE axis. Here we derive the uncertainties from tilt to leading order in the tilt angle.

42 ENGINEERING↗

Gravity and Extreme Magnetism SMEX

Gas accreting ont,o black holes and neutron stars form a dynamic system generating X-rays with spectroscopic signatures and varying on time scales determined by the system. The radiation from various parts of these systems is surely polarized and compact sources have been calculated to give rise to net polarization from the unresolved sum of the radiation from the systems. Polarization has been looked to for some time as also bearing the imprint of strong gravity and providing complementary information that could resolve ambiguities between the physical models that can give rise to frequencies, time delays, and spectra. In the cases of both stellar black holes and supermassive black holes the net polarizations predicted for probable disk and corona models are less than 10 needed. This sensitivity can be achieved, even for sources as faint as 1 milliCrab, in the Gravity and Extreme Magnetism SMEX (GEMS) mission that uses foil mirrors and Time Projection Chamber detectors. Similarities have been pointed out between the timing and the spectral characteristics of low mass X-ray binaries and stellar black hole sources. Polarization measurements for these sources could play a role in determining the configuration of the disk and the neutron star.

Swank, Jean↗

Thermal X-rays and deuterium production in stellar flares

The X-ray spectrum of flares is shown to be necessarily thermal up to at least 200 keV because the self-magnetic field of any electron stream required for a thick- or thin-target source is inconsistently large. The resulting flare model can then be related to stellar luminosity convection, and magnetic fields to result in a maximum possible gamma-burst and continuous X-ray flux. One of the most striking isotopic anomalies observed is the extreme enrichment of He-3 in some solar flares and the mysterious depletion of deuterium. The way in which deuterium may be produced and emitted in the largest flares associated with gamma-bursts but in amounts insufficient to support the tentative conclusion of Coleman and Worden (1976) is discussed.

Colgate, S. A.↗

Auroral kilometric radiation/aurora correlation

Auroral kilometric radiation (AKR) observations from the ISIS 1 topside sounder receiver were compared with visual auroral observations from the network of Alaskan all-sky camera stations. The goal was to relate AKR source region encounters to specific auroral forms on the same magnetic field line. Thirty-eight simultaneous data sets were identified and analyzed. In general, intense AKR was associated with bright auroral arcs and conditions of weak or no AKR corresponded to times when either no aurora or only a faint arc or weak diffuse aurora were observed. Five cases, when both intense AKR and bright visual aurora were present, were analyzed in detail. Complete electron density N sub e contours, from the satellite altitude down to the F region ionization peak, were obtained along N-S traversals of the AKR source region. In addition, the ISIS 1 orbital tracks were projected down the magnetic field lines to the auroral altitude and compared to auroral features on a map derived from the all sky camera images. Density cavities (regions where N sub e 100/cu cm) were encountered on each of these passes.

Benson, R. F.↗

Auroral kilometric radiation/aurora correlation

Auroral kilometric radiation (AKR) observations from the ISIS 1 topside sounder receiver were compared with visual auroral observations from the network of Alaskan all-sky camera stations. The goal was to relate AKR source region encounters to specific auroral forms on the same magnetic field line. Thirty-eight simultaneous data sets were identified and analyzed. In general, intense AKR was associated with bright auroral arcs and conditions of weak or no AKR corresponded to times when either no aurora or only a faint arc or weak diffuse aurora were observed. Five cases, when both intense AKR and bright visual aurora were present, were analyzed in detail. Complete electron density N sub e contours, from the satellite altitude down to the F region ionization peak, were obtained along N-S traversals of the AKR source region. In addition, the ISIS 1 orbital tracks were projected down the magnetic field lines to the auroral altitude and compared to auroral features on a map derived from the all sky camera images. Density cavities (regions where N sub e 100/cu cm) were encountered on each of these passes. Previously announced in STAR as N83-27516

Benson, R. F.↗

Direct E&M Field Solver for a Plane Wave without Sources

A three dimensional direct field solver for the electric and magnetic fields using the Finite Difference Time Domain (FDTD) method is described. Example simulations using periodic and absorbing boundary conditions in a vacuum medium for a plane wave propagating in three dimensions are explored and are compared to theory.

97 MATHEMATICS AND COMPUTING↗

Pulsed Magnet Power Systems at NSLS-II

The National Synchrotron Light Source - II (NSLS-II) is a 3 GeV X-ray user facility with 29 beamlines. The NSLS-II pulsed power system consists of an event generator for timely injection and extraction of beam in the transport line from linac to booster at 170 MeV, and from booster to storage ring at 3 GeV. We will discuss current pulsed power systems and the future upgrades/improvements on those systems.

43 PARTICLE ACCELERATORS↗

CME Interaction with Coronal Holes and Their Interplanetary Consequences

A significant number of interplanetary (IP) shocks (-17%) during cycle 23 were not followed by drivers. The number of such "driverless" shocks steadily increased with the solar cycle with 15%, 33%, and 52% occurring in the rise, maximum, and declining phase of the solar cycle. The solar sources of 15% of the driverless shocks were very close the central meridian of the Sun (within approx.15deg), which is quite unexpected. More interestingly, all the driverless shocks with their solar sources near the solar disk center occurred during the declining phase of solar cycle 23. When we investigated the coronal environment of the source regions of driverless shocks, we found that in each case there was at least one coronal hole nearby suggesting that the coronal holes might have deflected the associated coronal mass ejections (CMEs) away from the Sun-Earth line. The presence of abundant low-latitude coronal holes during the declining phase further explains why CMEs originating close to the disk center mimic the limb CMEs, which normally lead to driverless shocks due to purely geometrical reasons. We also examined the solar source regions of shocks with drivers. For these, the coronal holes were located such that they either had no influence on the CME trajectories. or they deflected the CMEs towards the Sun-Earth line. We also obtained the open magnetic field distribution on the Sun by performing a potential field source surface extrapolation to the corona. It was found that the CMEs generally move away from the open magnetic field regions. The CME-coronal hole interaction must be widespread in the declining phase, and may have a significant impact on the geoeffectiveness of CMEs.

Gopalswamy, N.↗

Wireless Measurement of Rotation and Displacement Rate

A magnetic field response sensor is designed to measure displacement or rotation rate without a physical connection to a power source, microprocessor, data acquisition equipment, or electrical circuitry. The sensor works with the magnetic field response recorder, which was described in Magnetic-Field-Response Measurement-Acquisition System, NASA Tech Briefs, Vol. 30, No. 6 (June 2006), page 28. These sensors are wirelessly powered and interrogated, and the measurement acquisition system and sensors are extremely lightweight.The response recorder uses oscillating magnetic fields to power the sensors. Once powered, the sensors respond with their own magnetic field. For displacement/ rotation measurements, the response recorder uses the sensor s response amplitude, which is dependent on the distance from the antenna. The recorder s antenna orientation and position are kept fixed, and the sampling period is constant.

Woodard, Stanley E.↗

A self-consistent model of a corotating Jovian magnetosphere

In the rotation-dominated model of the Jovian magnetosphere, proposed in the present paper, the plasma current distribution is dynamically consistent with the magnetic field. The model is constructed under the assumptions of an ionospheric plasma source without pitch angle scattering; loss-free radiation transport through flux tube interchange diffusion; and a static balance between centrifugal force and magnetic stress. Using these assumptions, a dynamic equation is derived for a self-consistent field configuration having a single adjustable parameter that is related to the plasma source strength. The equation is solved by an iterative technique. The self-consistent field resembles a radially distorted dipole field, rather than the flat magnetodisk configuration inferred from Pioneer data. The implication is that such a magnetodisk field would require an equatorial plasma source rather than a source at the feet of the field lines.

Carbary, J. F.↗