Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Interlayer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Diffusion bonding of tungsten-vanadium-zirconium using vacuum hot pressing for the development of a low decay heat cladding solution for tungsten spallation targets

Tantalum has been used as cladding material for water-cooled solid tungsten targets at many leading spallation neutron production facilities thanks to its high neutron yield, manageable radiation damage behavior, and excellent corrosion/erosion resistance in radiation environments. However, from a safety hazard perspective, thermal neutron capture of tantalum in spallation environments causes a high specific decay heat in the target volume, which often becomes a limiting factor in increasing the beam power on the target. In this paper, we studied vacuum hot pressing (VHP) parameters to diffusion bond zirconium to tungsten to explore the feasibility of using zirconium alloys as an alternative cladding material to tantalum. Zirconium alloys have long been used as cladding material for early generation solid spallation targets, and nuclear fuel rods. In spallation environments zirconium has significantly lower decay heat with shorter decay time compared to tantalum. The hot isostatic pressing (HIP) of zirconium and tungsten is known to produce limited bonding quality due to the formation of the brittle ZrW2 intermetallic layer. To overcome this problem, placing a vanadium interlayer between tungsten and zirconium has been proposed by exploring parameter space in binary alloy phase diagrams. Under the VHP conditions, 860 ◦C at 70 MPa for 4 hours, Zr-V and V-W showed good diffusion bonding, which demonstrates the feasibility of a single step HIP process to make the zirconium alloy clad tungsten spallation volumes.

Lee, Yong Joong↗
DOE OSTI2020

The new K, Pb-bearing uranyl-oxide mineral kroupaite: Crystal-chemical implications for the structures of uranyl-oxide hydroxy-hydrates

Abstract Kroupaite (IMA 2017-031), ideally KPb0.5[(UO2)8O4(OH)10]·10H2O, is a new uranyl-oxide hydroxylhydrate mineral found underground in the Svornost mine, Jáchymov, Czechia. Electron-probe micro-analysis (WDS) provided the empirical formula (K1.28Na0.07)Σ1.35(Pb0.23Cu0.14Ca0.05Bi0.03Co0.02Al0.01)Σ0.48 [(UO2)7.90(SO4)0.04O4.04(OH)10.00]·10H2O, on the basis of 40 O atoms apfu. Sheets in the crystal structure of kroupaite adopt the fourmarierite anion topology, and therefore kroupaite belongs to the schoepite-family of minerals with related structures differing in the interlayer composition and arrangement, and charge of the sheets. Uptake of dangerous radionuclides (90Sr or 135Cs) into the structure of kroupaite and other uranyl-oxide hydroxy-hydrate is evaluated based on crystal-chemical considerations and Voronoi-Dirichlet polyhedra measures. These calculations show the importance of these phases for the safe disposal of nuclear waste.

Geochemistry & Geophysics↗
DOE OSTI2020

Twisted bilayer graphene: topological pumping and switching of topology by current [Slides]

The presentation was prepared for a BLABS seminar and includes various graphical images. The summary given highlighted: Topological pumping can be triggered by interlayer sliding in TBG due to the nontrivial topology associated with the synthetic dimension; Time-reversal symmetry of TBG can be spontaneously broken by Coulomb interaction, that results in the valley-polarized QAH state at 3/4 filling; A large enough current can pump electrons from the valence band to conductance band, that redistributes the electron occupation; and, the redistribution of electron occupation combined with the Coulomb interaction can switch the valley polarization and topology.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development of Large Scale Extrusion Deposition for Structural Applications

Large Scale Extrusion Deposition (LSED) is an evolving additive manufacturing (AM) technology that research, such as that taking place at Oak Ridge National Laboratory (ORNL) and companies like Local Motors, are continuing to utilize and develop new applications. A major LSED application of interest has been molds and tooling as it allows for much shorter production time and lower cost. However, interest has been expanding into using LSED for more structural applications due to more frequent use of high performing polymer composites as feedstock. The use of LSED for structural applications is of particular interest to Local Motors as it is currently being used to create commercially viable, energy efficient electric vehicles. LSED offers a unique opportunity when compared to traditional manufacturing methods as it can significantly reduce the number of components necessary, while decreasing embodied energy and carbon emissions. Even with these benefits however, it is important that LSED is properly understood from a structural aspect as this field has not been as heavily researched as tooling. To ensure a high level of safety and repeatability is an essential responsibility of a manufacturer whose products are structural in nature. As such it is important to understand the materials and LSED process to make structural objects that the manufacturer can be confident in. The main goals of this project were to: develop and investigate materials that are of interest for structural LSED applications, further develop and understand the current machines used in LSED and develop simulations tools of LSED and the mechanical properties of the created structure. Material development focused on composite materials that have high mechanical properties and are stable in a variety of environments. The materials were tested to determine their as printed mechanical and thermal properties as these are necessary for simulations. Once the materials were investigated thoroughly, it allowed for simulations to be performed to compare to experimental data with simulations. Materials were also vetted to determine candidates for multi-material printing. The machine development focused around the areas of process monitoring, non-destructive evaluation, and quality control. Finally, the goal of the simulations was to develop a realistic model of printed structures, including in-process simulation and dynamic simulation. The routes to get to some of these goals and the depth in which they were investigated changed throughout the project due to personnel changes and the COVID-19 pandemic. This project resulted in many valuable results such as the development of an nondestructive evaluation (NDE) technique for interlayer defects, proof of simulation for warpage in simple parts, the development and utilization of a profilometer to monitor a print for defects or inconsistencies, thorough investigation of a material used commercially for structural LSED applications and valuable experimental data on the applicability and advantages of multi-material crush structures versus their neat counterparts by creation and testing of samples.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Advanced Module Architecture for Reduced Costs, High Durability and Significantly Improved Manufacturability (Final Report)

This project demonstrated a new module architecture (referred to herein as Glass/Glass) using silicone edge seals and an interlayer polymer that reduces manufacturing costs, significantly streamlines manufacturing processes, and reduces cap-ex costs while improving module reliability. A prototype manufacturing process to fabricate this new module architecture was demonstrated with a significantly improved process cycle time for the lamination step from the current industry standard of 13.5 minutes to approximately 30 seconds for each of the individual edge seal and internal polymer application steps. Samples are fabricated, strenuously stressed, and characterized to quantify the cost benefits, hardware capacities and accelerated stress performance of the new architecture. These results are being compared to a standard, laminated baseline architecture using a Glass/EVA/Glass or Glass/Thermoplastic/Glass design that traditionally has high moisture vapor transmission rates (MVTR).

14 SOLAR ENERGY↗
DOE OSTI2022

Compression Analysis of Materials via in situ X-ray Computed Tomography

X-ray computed tomography (X-ray CT) is an analytical technique used in materials science to non– destructively characterize features in a variety of materials like polymers, metals, composites, and explosives. The non-destructive imaging allows for the analysis of features (voids and cracks), which give a fundamental understanding of material characteristics.This is more effective when combinedwith a load cell to expose the material to realworld stimuli to understand material characteristics and morphological behavior in situ. This study focused on using in situ X-ray CT to understand the material characteristics and morphological changes of sugar prills and a lattice under a compressive load. Sugar prills are used as a surrogate to analyze explosives in a safer and less expensiveway. The sugar prills were found to be brittle and shattered when compressed via the CT renderings and the stress/strain information. The lattices are used as both the basis and ground truth comparison for the development of models to predict the morphological and material characteristic changes that occur as a result of loading. The lattice was found to have weak regions due to low polymer interlayer fusion in these regions during the printing process. It was also found that under the initial compression the lattice demonstrated elastic behavior as its cellular structure was intact until the cellular structure started to collapse causing yielding in the lattice. Additionally, the analysis of the sugar prills and lattice demonstrate the information that can be gleaned from in situ X-ray CT experiments that would be lost in traditional pre- and post-mortem X-rayCT analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High Performance SOFCs with a Superior Stability for Reliable and Durable Power Systems

Next generation of fuel cells, electrolyzers, and batteries requires higher power, faster kinetics, and larger energy density, which necessitate the use of compositionally complex oxides to achieve multifunctionalities and activity. These compositionally complex oxides may change their phases and structures during an electrochemical process – a so-called “electrochemically driven phase transformation”. The origin for such a phase change has remained obscure. More importantly, there is a need to develop high performance solid oxide fuel cells with an enhanced stability. In this work, the La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) cathode surface is modified by infiltration of Pr 6 O 11 and the power density at 0.8V and 750 °C is improved by 21%. In addition, by replacing the traditional barrier layer Gd 0.2 Ce 0.8 O 1.9 with mixed conducting Pr 0.1 Gd 0.1 Ce 0.8 O 1.9 , the power density increases by 38%. The different mechanism of promotions was investigated by electrochemical impedance spectroscopy. The ohmic resistance is dramatically reduced by applying the PGCO interlayer, and the distribution of relaxation time was used to analyze the mechanism for which the polarization resistance was decreased attributing to the mixed conduction nature in PrO x . An increase of power density at 0.8 V of 0.358 W/cm 2 (71%) is achieved with the implementation of both surface modification and buffer layer engineering. An experimental study and a theoretical analysis were then carried out on phase evolution in praseodymium nickelates. Nickelate-based electrodes show up to 60× greater phase transformation during operation when compared to thermally annealed ones. Theoretical analysis suggests that the presence of a reduced oxygen partial pressure at the interface between the oxygen electrode and the electrolyte is the origin for the phase change in an oxygen electrode. Guided by the theory, an addition of the electronic conduction in the interface layer leads to the significant suppression of phase change, while improving cell performance and performance stability. When an oxygen electrode is under polarization, the oxygen partial pressure at the interface between the oxygen electrode and the electrolyte is lower than that of incoming oxidant. Under a high polarization, the environment at the aforementioned interface may lead to phase transformation of the oxygen electrode. The local oxygen partial pressure is determined by the transport properties at the interfaces. An addition of the electronic conduction in the interface layer, for instance using (Pr,Gd)-doped ceria to replace Gd-doped ceria, results in improved cell performance and performance stability, while the phase transformation is significantly suppressed. This work provides a fundamental understanding of the origin for phase transformation in oxygen electrodes during operation and use this knowledge to develop a high-performance electrode that exhibits improved performance stability.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Development of Roll-to-Roll Simultaneous Multilayer Deposition Methods for Solid-state Electrochemical Devices using Highly Particulate Loaded Aqueous Inks

A platform for simultaneous multilayer roll-to-roll coating was developed for solid-state electrochemical devices through Saint-Gobain’s Solid Oxide Fuel Cell. Six wet layers were successfully coated one top of another using multilayer slide coating following design rules developed through a step-wise approach. Solid oxide fuel cells, which comprise of engineered ceramic films, were made with dual slot and multi-layer slide dies and shown to have similar performance to cells made with incumbent coating methods. Additionally, interlayers were coated below their individual singular low flow limits using simultaneous multilayer coating.

08 HYDROGEN↗
DOE OSTI2022

Metal-Tipped and Electrochemically Wired Semiconductor Nanocrystals: Modular Constructs for Directed Charge Transfer

In our 2017 proposal to the Solar Photochemistry division of DOE/BES/Office of Science we targeted the creation, characterization and integratation of new II-IV semiconductor heterostructured nanomaterials into ultra-thin film (tethered) nanocrystalline arrays on transparent metal oxide (TCO) supports. Materials were to include CdSe quantum dots (QDs), asymmetric CdSe@CdS tetrapods (TPs) and CdSe@CdS nanorods (NRs), into unique photoelectrochemical platforms. The ultimate goal was to tether these new nanomaterials to either electron- or hole-selective oxide interlayers that would afford vectoral photo-induced charge transfer and ultimately formation of molecular products such as H 2 . This was an ambitious set of goals but integrated well with our previous work in this general area.

14 SOLAR ENERGY↗
DOE OSTI2023

Studies of Reactive Amorphous Compounds and Surfaces: Their Pathways to Crystallinity and Surface Functionality

This project was originally headed by Dr. Abraham Clearfield (Texas A&M University, ret.) and focused on developing structural models of zirconium phosphate (ZrP) based materials at different stages of crystalline order using PDF techniques developed by co-PI Dr. Simon Billinge (Columbia University). When Dr. Clearfield retired, the project was taken over by Dr. Hong-Cai Zhou (Texas A&M University). The project proposed looking at defective metal-organic frameworks (MOFs) supported on the surface of the ZrP materials. During the project, the personnel conducted studies of the dispersion of different phosphate ligands in mixed organic phosphonates, and how they could be utilized to incorporate different metals within the ZrP interlayer spacing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Quantum Transport in 2D Semiconductors

Leveraging progress in synthesis of ultra-pure transition metal dichalcogenide (TMD) crystals, our team has made key breakthroughs in the study of quantum states in two-dimensional (2D) TMD semiconductors. Using a capacitance spectroscopy technique, we have observed the first signatures of fractional quantum Hall states in monolayer WSe 2 and clear signatures of interlayer exciton condensates in bilayer WSe 2 . In a transport study of bilayer WSe 2 , we report observation of spin-selective magneto-conductivity in WSe 2 . To improve electrical transport studies, we have focused on metal-TMD contacts by studying the behavior of metal-TMD contacts in the clean limit, and developing a new contact doping technique that achieves Ohmic contact down to low temperature and low carrier density. Using this new technique, we study electrical transport in monolayer WSe 2 down to low temperature and low carrier density, finding record-high hole mobility and evidence of a metal-insulator transition at low density. Under high magnetic fields, we observe clear signatures of fractional quantum Hall effect in transport for the first time in a TMD.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Alternate Methods for Cleaning Zirconium Plate

The United States High Performance Research Reactor Conversion Program identified the need to transition from highly enriched uranium fuel to lowly enriched uranium fuel for high power research and civil reactors. One of the fuel configurations selected for these reactors was a uranium (U) foil alloyed with 10% molybdenum (Mo). The U-10Mo fuel foil was then covered with a zirconium (Zr) interlayer and pressed into an aluminum cladding. Idaho National Laboratory prescribed a need to remove surface oxidation on the Zr prior to bonding it with U-10Mo fuel foil. To determine the best method of oxidation removal, a variety of polishing methods, including hand polishing with a diamond paste or Scotch-Brite™ pads, mechanically wet-polishing with abrasive belts, and chemical etching with hydrofluoric/nitric acid mixtures, were investigated on pre-polished Zircaloy 702 sheets purchased directly from the manufacturer. No change in surface roughness was detected using any of these methods relative to the as-received material. In fact, scanning electron microscopy detected grit from hand polishing with Amplex Grade 30 waste soluble diamond paste and Scotch-Brite™ pads. Visible staining was found, and fluorine detected via X-ray photoelectron spectroscopy on the flash etching samples. These contaminants were not seen on the as-received material. In addition to the need to remove the oxide layer on the Zr prior to co-rolling, there are concerns that the Neolube debonding agent on the co-rolling can may contaminate the Zr surface after co-rolling. The experimental results found that zirconium in contact with Neolube coated steel plates was easily cleaning with ethanol wiping after heat treated and no carbide inclusions remained on the surface. Overall, all cleaning methods tested did not significantly change the surface roughness of the plates or reduce the oxide layer present on the zirconium. Carbon was found on all the samples, before and after cleaning, except for the flash etch samples which detected fluorine instead. The insignificant changes seen in the cleaned plates relative to the as received plates question the need for cleaning prior to rolling. Further investigation in the requirements for cleaning at this step is recommended. Current methods for cleaning the surface after hot rolling with alcohol appear sufficient. After hot rolling, if Neolube does peel off the can and onto the zirconium coated foil surface, a dry abrasive or diamond paste polish is not recommended due to the chance of abrasive being embedded into the surface. However, the ability of an etchant to lift the lubricant off the zirconium surface indicates that a spot etch method could work to clean specific spots where Neolube is present, if the need arises.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

PILBCP-IL Composite Ionomers for High Current Density Performance

Wide-spread commercialization of fuel cell electric vehicles using proton exchange membrane fuel cell (PEMFC) power sources requires that several existing limitations be addressed. These include: (1) a reduction in platinum (Pt) loading in the catalytic electrodes, (2) improvements in reactant and electronic mobility throughout the catalytic electrodes, (3) reduction in the reliance on materials derived from polluting “forever chemicals”, and (4) a significant improvement in the operational longevity of catalytic electrode components. In this project, a team of two universities, Drexel University and Texas A&M University, one national lab, National Renewable Energy Laboratory, and one company, General Motors, collaborated to develop a new cathode ionomer chemistry that would address these limitations and result in an improvement in performance over existing ionomer materials. The key technology developed through this collaborative project was a composite cathode ionomer encompassing an ionic liquid interlayer between Pt catalysts and a sulfonated polymerized ionic liquid block co-polymer (S-PILBCP) that possess the orthogonal properties of protonic conductivity and ionic liquid enhanced kinetics and durability (see schematic in Figure 1). The composite S-PILBCP ionomer eliminates many of the existing issues with perfluorosulfonic acid-based ionomers including active site blocking by sulfonate specific adsorption, restricted O 2 transport through ionomer films, limited humidity tolerance and active area loss for carbon pore confined catalyst particles, and use of polluting “forever chemicals”. Following successful integration of the developed composite ionic liquid into a PEMFC cathode catalyst layer, we demonstrate enhanced performance over Nafion containing cathodes with Pt/C and PtCo/C at both low and high current density. The performance with our composite S-PILBCP ionomer meets the Department of Energy (DOE) targets for light duty vehicle applications

08 HYDROGEN↗
DOE OSTI2023

Emergent Quantum Magnetism and Cryogenic Spin-Memory in Twisted Bilayer Graphene

Recently developed techniques for assembling moiré heterostructures have enabled unprecedented control of the interlayer interactions within the heterostructure, allowing for the realization of strongly correlated electronic states. The experimentally realized states, to date, include a variety of topological states, superconductivity, and strange metal behavior. However, the phenomenology varies significantly from sample to sample. Here we will present microscopy techniques for further characterization of both the progenitor exfoliated materials and the composite moiré heterostructure. The application of these techniques has allowed for an unprecidented degree of characterization in ambient conditions. Additionally we will explore the use of resistively detected electron spin resonance (ESR) as a novel probe for spin order in moirés. While our results do not show clearly dispersive features that would unambiguously evince spin excitations within the sample, the technique is still promising.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

A Scalable & Non-Destructive Characterization Strategy to Study Semiconductor/Dielectric Interfaces and Predict Wafer-Level Device Performance

The defect density present at the dielectric-semiconductor interface in an MOS structure directly influences the channel carrier characteristics in semiconductor devices, especially in wide bandgap material systems used in power devices. While these trap defects are typically quantified through electrical characterization of MOS-capacitor test structures, this treatment offers very little insight into the physical nature of interface defects. Such shortcomings demand a physical characterization strategy to guide fabrication optimization. X-ray photoelectron spectroscopy (XPS) is suggested as a viable technique to determine chemical data for dielectric interfaces formed using atomic layer deposition (ALD) on GaN substrates. Previously, 1-D XPS characterization has confirmed the presence of a Ga x O y interlayer between ALD dielectrics and the GaN substrate. In this work, XPS data is serially collected to form 2-D images of an ALD-Al 2 O 3 /GaN interface as a proof-of-concept experiment for in-situ XPS quality monitoring during ALD processing. The information provided by this work reveals some of the challenges for incorporating XPS characterization as an in-situ strategy during fabrication of GaN-based devices. Separately, electrical mapping of a 2-D array of ALD-Al 2 O 3 /GaN MOS-capacitor devices provide a means to quantify the spatial variations in interface quality across a single wafer. Physical characterization techniques, such as time-of-flight secondary ion mass spectroscopy, provide additional chemical information about the Al 2 O 3 /Ga x O y /GaN structure that complement the electrical mapping results. This analysis shows that a higher Ga x O y content correlates with higher interface state defects for trap energies deep in the band gap.

42 ENGINEERING↗
DOE OSTI2025

Location-Specific Microstructures and Properties of Haynes 282 Alloy with Laser-Wire DED Processing

In this work, the location-specific microstructures in terms of grain morphology, texture, γ′ precipitates, carbides, and residual strains were investigated in a series of laser-wire direct energy deposition (LW-DED) Haynes 282 alloys with varied processing parameters. A bimodal grain distribution was found in these as-printed and heat-treated alloys with columnar grains within the layers and fine equiaxed grains at the interlayer regions. Dominant <001> texture along the build direction with more obvious <111> orientation preference exists at the bottom layers, compared to the top layers. The gradient γ′-precipitates size distribution contributes predominantly to the observed gradient hardness distribution in the as-printed samples. The heat-treated 282 exhibit comparable yield strengths to those conventionally-processed counterparts, while the observed small deviation in their yield strengths is attributed to the Hall-Petch effect. This work establishes the correlation between location-specific microstructures and mechanical properties, providing valuable insights into future printing parameters and heat-treatment optimization.

Haynes 282↗
DOE OSTI2025

Low-Cost, Scalable Sorbents with Balanced Capacity-Kinetics-Thermodynamics for H2 Storage

The goal of this project is to utilize cutting-edge materials science, chemistry, and process engineering to demonstrate the feasibility of a new class of scalable sorbents with unprecedented balance of capacity-kinetics-thermodynamics for H 2 storage in fossil fuel power plants . The core fabrication leverages the unique exotic properties (e.g., high H 2 affinity, ultrahigh surface area, and exceptional thermal, mechanical and chemical stability) of the emerging 2D materials i.e. hexagonal boron nitride (hBN) followed by strategic coupling with alkali metals (Li, Na) dopants and optimal interlayer distance to deliver a stable, long-term energy storage for the grid. Figure 1 shows how this technology works.

08 HYDROGEN↗
DOE OSTI2025

Hydrogen isotope fractionation – Fundamental insights leaving to process scaleup

This final report summarizes the PhD research of Dr. Mayura Silva who was supported on the project from inception in August 2021 to his graduation in December 2023. Dr. Silva undertook a detailed examination of the eGicacy of graphene interlayers on H/D selectivity in electrochemical proton / deuteron pump cells. His work focused on the role of impurity cations (especially NH 4 * and Cu 2+ which are resident in membranes as a residual from the ammonium persulfate treatment used to remove copper backing from the graphene during membrane preparation), and on the composition of evolved gases from hydrogen / deuterium pump cells that were fed a 50:50 mixture of H 2 and D 2 gas. The key finding is that previous reports of very high H/D selectivity in hydrogen pump cells having Nafion | graphene | Nafion membranes installed were not reproduced.

08 HYDROGEN↗