Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IMPINGEMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Erosion of composite materials

A model for describing the response of uncoated and coated fiber reinforced composites subjected to repeated impingements of liquid (rain) droplets is presented. The model is based on the concept that fatigue is the dominant factor in the erosion process. Algebraic expressions are provided which give the incubation period, the rate of mass loss past the incubation period, and the total mass loss of the material during rain impact. The influence of material properties on erosion damage and the protection offered by different coatings are discussed and the use of the model in the design in the design of structures and components is illustrated.

Springer, G. S.↗
NASA NTRS1980

Measurements of the sampling volume of an infrared laser doppler velocimeter for the study of feasibility of simultaneous three-dimensional velocity profile mapping

High resolution incoherent mapping of the sampling volume was performed to determine the three dimensional profile of the volume of the beam from which information can be obtained by scattering. The incoherent sampling volume of the infrared laser Doppler velocimeter was found to be heavily dependent upon the configuration of the outgoing laser beam. In general when only half the beam is allowed to focus at the focal plane, the x, y traverses indicate a broader beam with nominal side lobes. However, if the total beam is permitted to impinge on the focal plane there is substantial narrowing of the beam with increased maximum intensity and an increase in side lobes. The double maximum indicated by the coherent sampling volume appears to be an artifact of the scanning process not a fundamental entity of the sampling volume.

Bond, R. L.↗
NASA NTRS1980

Energetics of the magnetosphere

The approximate magnitudes of several power inputs and energies associated with the Earth's magnetosphere will be derived. They include: Solar wind power impinging on the dayside magnetopause approximately 1.4 10 to the 13th power watt; power input to cross tail current approximately 3 10 to the 11th power watt; energy of moderate magnetic storm approximately 2 10 to the 15th power joule; power related to the flow of j approximately 1 to 3 10 to the 11th power watt; average power deposited by the aurora approximately 2 10 to the 10th power watt. Stored magnetic energy: released in a substorm approximately 1.5 10 to the 14th power joule. Compared to the above, the rate at which energy is released locally in magnetospheric regions where magnetic merging occurs is probably small. Merging is essential, however, for the existence of open field lines, which provide the most likely explanation for some major energy inputs listed here. Merging is also required if part of the open flux of the tail lobes is converted into closed flux, as seems to happen during substorms. Again, most of the energy release becomes evident only beyond the merging region, though some particles may gain appreciable energy in that region itself, if the plasma sheet is completely squeezed out and the high latitude lobes interact directly.

Stern, D. P.↗
NASA NTRS1978

Analytical study of STOL Aircraft in ground effect. Part 1: Nonplanar, nonlinear wing/jet lifting surface method

A nonlinear, nonplanar three dimensional jet flap analysis, applicable to the ground effect problem, is presented. Lifting surface methodology is developed for a wing with arbitrary planform operating in an inviscid and incompressible fluid. The classical, infintely thin jet flap model is employed to simulate power induced effects. An iterative solution procedure is applied within the analysis to successively approximate the jet shape until a converged solution is obtained which closely satisfies jet and wing boundary conditions. Solution characteristics of the method are discussed and example results are presented for unpowered, basic powered and complex powered configurations. Comparisons between predictions of the present method and experimental measurements indicate that the improvement of the jet with the ground plane is important in the analyses of powered lift systems operating in ground proximity. Further development of the method is suggested in the areas of improved solution convergence, more realistic modeling of jet impingement and calculation efficiency enhancements.

Shollenberger, C. A.↗
NASA NTRS1981

Environmental effects and large space systems

When planning large scale operations in space, environmental impact must be considered in addition to radiation, spacecraft charging, contamination, high power and size. Pollution of the atmosphere and space is caused by rocket effluents and by photoelectrons generated by sunlight falling on satellite surfaces even light pollution may result (the SPS may reflect so much light as to be a nuisance to astronomers). Large (100 Km 2) structures also will absorb the high energy particles that impinge on them. Altogether, these effects may drastically alter the Earth's magnetosphere. It is not clear if these alterations will in any way affect the Earth's surface climate. Large structures will also generate large plasma wakes and waves which may cause interference with communications to the vehicle. A high energy, microwave beam from the SPS will cause ionospheric turbulence, affecting UHF and VHF communications. Although none of these effects may ultimately prove critical, they must be considered in the design of large structures.

Garrett, H. B.↗
NASA NTRS1980

Jet-diffuser Ejector - Attached Nozzle Design

Attached primary nozzles were developed to replace the detached nozzles of jet-diffuser ejectors. Slotted primary nozzles located at the inlet lip and injecting fluid normal to the thrust axis, and rotating the fluid into the thrust direction using the Coanda Effect were investigated. Experiments indicated excessive skin friction or momentum cancellation due to impingement of opposing jets resulted in performance degradation. This indicated a desirability for location and orientation of the injection point at positions removed from the immediate vicinity of the inlet surface, and at an acute angle with respect to the thrust axis. Various nozzle designs were tested over a range of positions and orientations. The problems of aircraft integration of the ejector, and internal and external nozzle losses were also considered and a geometry for the attached nozzles was selected. The effect of leaks, protrusions, and asymmetries in the ejector surfaces was examined. The results indicated a relative insensitivity to all surface irregularities, except for large protrusions at the throat of the ejector.

Alperin, M.↗
NASA NTRS1981

A sputtered zirconia primer for improved thermal shock resistance of plasma sprayed ceramic turbine seals

The development of plasma-sprayed yttria stabilized zirconia (YSZ) ceramic turbine blade tip seal components is discussed. The YSZ layers are quite thick (0.040 to 0.090 in.). The service potential of seal components with such thick ceramic layers is cyclic thermal shock limited. The most usual failure mode is ceramic layer delamination at or very near the interface between the plasma sprayed YSZ layer and the NiCrAlY bondcoat. Deposition of a thin RF sputtered YSZ primer to the bondcoat prior to deposition of the thick plasma sprayed YSZ layer was found to reduce laminar cracking in cyclic thermal shock testing. The cyclic thermal shock life of one ceramic seal design was increased by a factor of 5 to 6 when the sputtered YSZ primer was incorporated. A model based on thermal response of plasma sprayed YSZ particles impinging on the bondcoat surface with and without the sputtered YSZ primer provides a basis for understanding the function of the primer.

Bill, R. C.↗
NASA NTRS1981

Fluorescent radiation converter

A fluorescence radiation converter is described which includes a substantially undoped optically transparent substrate and a waveshifter coating deposited on at least one portion of the substrate for absorption of radiation and conversion of fluorescent radiation. The coating is formed to substantially 1000 g/liter of a solvent, 70 to 200 g/liter of an organic polymer, and 0.2 to 25 g/liter of at least one organic fluorescent dye. The incoming incident radiation impinges on the coating. Radiation is absorbed by the fluorescent dye and is re-emitted as a longer wavelength radiation. Radiation is trapped within the substrate and is totally internally reflected by the boundary surface. Emitted radiation leaves the substrate ends to be detected.

Viehmann, W.↗
NASA NTRS1980

Inert gas thrusters

Some advances in component technology for inert gas thrusters are described. The maximum electron emission of a hollow cathode with Ar was increased 60-70% by the use of an enclosed keeper configuration. Operation with Ar, but without emissive oxide, was also obtained. A 30 cm thruster operated with Ar at moderate discharge voltages give double-ion measurements consistent with a double ion correlation developed previously using 15 cm thruster data. An attempt was made to reduce discharge losses by biasing anodes positive of the discharge plasma. The reason this attempt was unsuccessful is not yet clear. The performance of a single-grid ion-optics configuration was evaluated. The ion impingement on the single grid accelerator was found to approach the value expected from the projected blockage when the sheath thickness next to the accelerator was 2-3 times the aperture diameter.

Kaufman, H. R.↗
NASA NTRS1979

Spread spectrum techniques for the Space Shuttle

The Space Shuttle will employ spread spectrum techniques for both communication and navigation. During on-orbit phases of flight, two-way S-band and Ku-band communication links between the Shuttle and the ground will be available via the tracking and data relay satellite system (TDRSS). A pseudonoise (PN) code will spread the forward-link data spectrum from 32 kbps to 216 kbps to reduce the signal spectral density impinging on the earth's surface, with the S-band code search and acquisition being performed at C/NO-values of around 5 dB-Hz, and with a code length of 2047 chips at a rate of 11.232 Mchips/sec. C/NO-values in the region of 60 dB-Hz to 63 dB-Hz will characterize PN code acquisition in the Ku-band, whose forward-link PN clock is 3.03 Mchips/sec on a 1023-chip length sequence. Primary operational navigation will be provided by the Global Positioning System (GPS), which, after measuring transit time of the PN spread spectrum signal between a number of GPS satellites and itself, scales it by the velocity of light. GPS will enable position estimation accuracy to 30 feet and velocity estimation accuracy to 0.02 ft/sec.

Batson, B. H.↗
NASA NTRS1981

Liquid spray cooling of a heated surface

The lowest surface temperature possible for the existance of spray evaporative cooling is determined experimentally to be a linear function of the impinging spray mass flux. A conduction-controlled analytical model of droplet evaporation gives fairly good agreement with experimental measurements at atmospheric pressure. At reduced pressures droplet evaporation rates are decreased significantly such that an optimum operating pressure exists for each desired surface heat flux. The initiation of the 'Leidenfrost state' provides the upper surface temperature bound for spray evaporative cooling.

Grissom, W. M.↗
NASA NTRS1981

Inert-gas thruster technology

Attention is given to recent advances in component technology for inert-gas thrusters. It is noted that the maximum electron emission of a hollow cathode with Ar can be increased 60-70% by using an enclosed keeper configuration. Operation with Ar but without emissive oxide has also been attained. A 30-cm thruster operated with Ar at moderate discharge voltages is found to give double-ion measurements consistent with a double-ion correlation developed earlier on the basis of 15-cm thruster data. An attempt is made to reduce discharge losses by biasing anodes positive of the discharge plasma. The performance of a single-grid ion-optics configuration is assessed. The ion impingement on the single-grid accelerator is found to approach the value expected from the projected blockage when the sheath thickness next to the accelerator is 2-3 times the aperture diameter.

Kaufman, H. R.↗
NASA NTRS1981

Two-dimensional analytical model of twin jet shielding

Estimation of the impact of jet noise requires analytical modeling not only of the noise source mechanism, but also of the propagation of noise from the source to receiver. One factor which influences the jet noise path is shielding of one jet by another in a twin jet configuration. An analytical model is developed to investigate the shielding phenomenon. The two-dimensional wave equation is solved for a stationary line source impinging upon a cylinder of heated flow. The solution estimates the diffraction and scattering of the incident sound wave by the shielding jet in a plane normal to the jet axis. The frequency dependence of the normalized sound pressure estimated by the model is found to agree in form with empirical data. The azimuthal redistribution of the incident sound shows that, as the frequency of maximum shielding is approached, the scattered sound becomes more highly concentrated into lobes adjacent to the shielding zone.

Gerhold, C. H.↗
NASA NTRS1980

Composite wall concept for high-temperature turbine shrouds - Heat transfer analysis

The variables affecting the design of a composite turbine shroud, consisting of a metal base, an interlayer of porous metal, and an outer layer of yttria-stabilized zirconia, are analyzed. Results show that significant reductions in the cooling-air to gas-flow ratio are indicated for the composite shrouds compared to an all-metal shroud that was only impingement air cooled. The good insulating properties of the ceramic reduced the temperatures of the porous metal and support wall significantly. For a given porous metal density and coolant- to gas-flow ratio, decreasing the thickness of the porous metal and increasing ceramic thickness resulted in lower support wall temperatures. To maintain given allowable inter-layer temperatures and coolantto gas-flow ratios, porous-metal density or thermal conductivity must increase as the ratio of the thickness of the ceramic-to-porous metal decreases. It is concluded that a 1.78 mm thickness of porous material with a density of 0.2 and a 1.78 mm thickness of ceramic appears to be a good composite wall configuration for the assumed conditions

Ludwig, L. P.↗
NASA NTRS1981

Galileo maneuver analysis

In the maneuver analysis of the Galileo spacecraft, analytic models have been developed to assess the performance of an interplanetary dual spin spacecraft. These models take into account all the important effects of dual spin and flexible body dynamics to determine the spacecraft capability to achieve precise velocity changes for a variety of maneuver modes, as dictated by the requirements and as are tested and verified by computer simulation. Proportional velocity change magnitude accuracies as small as 0.34%, proportional velocity change pointing accuracies as little as 10 milliradians and fixed velocity change accuracies as precise as 0.015 m/sec are indicative of the stringency of these requirements. Error sources considered in the statistical analysis include probabilistic uncertainties due to wobble, plume impingement, nutation, thruster and accelerometer misalignments and radial offsets, gyro drift, burn timing, mass properties and algorithm errors. With its twelve thrusters, the versatility of the spacecraft to maneuver among the Galilean moons for eleven encounters after delivering a probe into the Jovian atmosphere provides a new level of challenge in the area of maneuver analysis.

Longuski, J. M.↗
NASA NTRS1954

A Procedure for the Design of Air-Heated Ice-Prevention Systems

A procedure proposed for use in the design of air-heated systems for the continuous prevention of ice formation on airplane components is set forth. Required heat-transfer and air-pressure-loss equations are presented, and methods of selecting appropriate meteorological conditions for flight over specified geographical areas and for the calculation of water-drop-impingement characteristics are suggested. In order to facilitate the design, a simple electrical analogue was devised which solves the complex heat-transfer relationships existing in the thermal-system analysis. The analogue is described and an illustration of its application to design is given.

Neel, C. B.↗
NASA NTRS1955

Preliminary Data on Rain Deflection from Aircraft Windshields by Means of High-Velocity Jet-Air Blast

A preliminary experimental investigation is being conducted to determine the feasibility of preventing rain from impinging on aircraft windshields by means of high-velocity jet-air blast. The results indicate that rain deflection by jet blast appears feasible for flight speeds comparable with landing and take-off speeds of interceptor-type jet aircraft; however, attainment of good visibility through the mist generated by raindrop breakup presents a problem. For the simulated windshield and the lower windshield angles used in the investigation, air-flow rates of the order of 3.3 pounds per minute of unheated air per inch of windshield span were required for adequate rain deflection at a free-stream velocity of 135 miles per hour. A method has been devised whereby it is possible to produce large-diameter water drops (1000 to 1500 p.) in a moving air stream, without breakup, at speeds in excess of 175 miles per hour.

Ruggeri, Robert S.↗
NASA NTRS1952

The Calculated and Measured Performance Characteristics of a Heated-Wire Liquid-Water-Content Meter for Measuring Icing Severity

Ground tests have been made of an instrument which, when assembled in a more compact form for flight installation, could be used to obtain statistical flight data on the liquid-water content of icing clouds and to provide an indication of icing severity. The sensing element of the instrument consists of an electrically heated wire which is mounted in the air stream. The degree of cooling of the wire resulting from evaporation of the impinging water droplets is a measure. of the liquid-water content of the cloud. Determination of the value of the liquid-water content from the wire temperature at any instant requires a knowledge of the airspeed, altitude, and air temperature. An analysis was made of the temperature response of a heated wire exposed to an air stream containing water drops. Comparisons were made of the liquid-water content as measured with several heated wires and absorbent cylinders in an artificially produced cloud. For one of the wires, comparative tests were made with a rotating-disk icing-rate meter in an icing wind tunnel. From the test results, it was shown that an instrument for measuring the concentration of liquid water in an air stream can be built using an electrically heated wire of known temperatureresistance characteristics, and that the performance of such a device can be predicted using appropriate theory. Although an instrument in a form suitable for gathering statistical data in flight was not built, the practicability of constructing such an instrument was illustrated. The ground-test results indicated that a flight heated-wire instrument would be simple and durable, would respond rapidly to variations in liquid-water content, and could be used for the measurement of water content in clouds which are above freezing temperature, as well as in icing clouds.

Neel, Carr B.↗