SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This report presents the work performed for welding 17-7PH stainless steel hemispheres, flanges, and accelerometer blocks. This includes weld development, microhardness measurements, calculated strengths, and distortion measurements after welding and heat treatment. The results of this report are utilized to propose a recommended welding procedure which was implemented for this experiment.
The Gear Test Assembly (GTA) has completed three experimental campaigns at the Mechanisms Engineering Test Loop (METL) facility. The most recent campaign tested Inconel 718 spur gears, tapered roller bearings of 52100 bearing steel with no heat treatment, and a lantern ring shaft seal with spring-loaded fasteners. Testing was performed in Test Vessel 1 (TV1) with 250°C sodium that had an oxide concentration of <10ppm. Testing began in February 2021 and was ended in March 2021 when a thrust bearing assembly failed, requiring shutdown and maintenance. The third experimental campaign completed 1,568 simulated fuel assembly maneuvers before the thrust bearing failure. The GTA was removed from TV1 and cleaned in the Carbonation System. The GTA is currently being prepared for the next experimental campaign. Nondestructive examination methods have been developed at Argonne to monitor the health of the GTA spur gears. Eddy current testing (ECT) and ultrasonic testing (UT) were performed prior to sodium testing and after each experimental campaign. The NDE has shown that the primary damage mechanism is mechanical wear on the gear tooth surface. Several larger nicks are observable on the gear faces, with additional large nicks present on the edges of the gear teeth. While this damage is observable, the overall health of the gears is adequate for more in-sodium testing. A total of 12,752 simulated fuel assembly maneuvers have been completed using this set of gears.
In this report, we make a recommendation for the PTW model parameters for an aluminum alloy, Al 6061-T6 based on the quasi-static and split-Hopkin pressure bar experimental data, provided by the experimentalists in MST-8, LANL. Al 6061 is an aluminum alloy with magnesium and silicon, and the temper designation T6 means it has gone through heat treatment followed by quenching, cooling, and aging. (Note that T4 is naturally aged and T6, artificially.) We adopted the shear modulus and melt curve models that are necessary to parameterize the PTW model, from Sesame EoS. In the lack of those information on this particular aluminum alloy, we used what is available for pure aluminum.
Two different types of cathode materials were prepared using glycerol as a solvent and reactant. The LiMn1/3Ni1/3Co1/3O2 layered oxide cathode material was successfully synthesized with a shorter time of heat treatment of 8hr at 900°C. An appreciated capacity retention of 83.7% after 100 cycles with an initial discharge capacity of 177.1 mAh/g at 0.1C (discharge rate) has been achieved. Another cathode material with the formula of Li1.2 Mn0.51Ni0.145+xCo0.145-xO2 (x=0 (LR2), 0.0725 (LR1)), as a Li-rich cathode material, has been also successfully synthesized using glycerol. It was shown that LR1 discharge capacity was increased from 185 to 213 mAh/g after 20 cycles and ended up with 194.9 mAh/g after 60 cycles at 0.1C (discharge rate). This material shows an exceptional discharge capacity retention, lower toxic cobalt component, and lower production cost comparing with other Li-rich cathode materials. Detailed results of powder material synthesis, characterization, and battery testing will be presented to demonstrate that glycerol as a green solvent in the synthesis of battery materials.
In this project, we attempted to make CdTe homojunctions using single crystal p-type doped substrates and closed-space sublimation epitaxy (CSSE) n-type doped films. The project included modeling which determined the ideal thickness for the n-type layer as being <200 nm. Boules of high concentration indium-doped CdTe and CdSe 0.4 Te 0.6 (CST) were grown using modified vertical Bridgman (MVB) methods. Similarly, iodine-doped CdTe crystals were grown for the first time. Washington State University (WSU) stock phosphorus-doped CdTe was used as the p-type substrate layer. The crystals were characterized by Hall effect and time-resolved photoluminescence (TRPL, for electrical properties), photoluminescence microscopy (for uniformity), X-ray diffraction (for crystal structure), and glow discharge mass spectrometry (GDMS, for dopant and impurity concentration). CdTe:I crystals were also characterized by visible and infrared transmission measurements, and various Cd or Te heat treatments were performed to assess changes in optical and electrical properties. The grown n-type materials – CdTe:In, CdSe0.4Te0.6:In, and CdTe:I – were provided to the National Renewable Energy Laboratory (NREL) for growth of CSSE thick films for characterization by two photon TRPL (for carrier lifetime), electron back-scatter diffraction (EBSD, to assess epitaxy), and Hall effect. Several measurements of secondary ion mass spectroscopy (SIMS) were performed. Nearly 100% of the indium from the crystal was incorporated into the measured thick films, while only ~2-22% of the iodine from the crystal was incorporated. The net result of the diffusion issue is that homojunction devices created using CSSE have a buried homojunction, as indicated by the near infrared peak in the external quantum efficiency (EQE). Various parameterization of front and back contacts suggested that the poor device performance was primarily a result of this buried junction and not due to other effects. There may also be an issue with the CSSE film lifetime in addition to the dopant profile.
Recent demand for coal as a thermal energy source has decreased significantly and will likely continue to decrease as renewable sources of energy become more available and environmental concern and cost from burning coal makes it more costly than renewables. Given that Powder River Basin (PRB) coal in Wyoming has relatively low thermal energy, it is critical for Wyoming to employ coal in other capacities at the current energy transition period in history. Among many potential non-thermal applications, PRB coal can be utilized for membrane and electrode applications through the formation of carbon fibers. Coal-derived membranes can become low-cost, conductive membranes for use in electrodialysis separation processes. Carbon fiber derived electrodes have been shown be a cost-effective alternative to typical electrode materials that can meet or exceed the performance of current carbon electrode materials. In this talk, we demonstrate the manufacture of supercapacitor electrodes from Powder River Basin (PRB) coal-derived precursors. Specifically, PRB coal was treated in cheap solvents, partitioned into liquid extract and solid residue. An electropinning process has been developed that can convert either the liquid extract or the solid residue into carbon fiber mats. The electrospinning process is versatile with many tunable process parameters to achieve desirable physiochemical properties. For example, the coal residue can be manipulated by additional heat treatment, or by adding binders, salts, or surfactants to create a solution that can be electrospun into advanced carbon electrodes with desirable structural and surface properties. Similarly, some of the liquid extract (tar fraction) can be subsequently reacted with toluene diisocyanate to create resinous coal-derived polyurethane (PUs) as a spinnable ink. Carbon nanofiber mats made from our proprietary electrospinning process were further carbonized at temperature ranging from 700°C to 900°C before they are used as electrodes in supercapacitors. Galvanostatic charge-discharge (GCD) results show that the best performing PU fiber mats can deliver a specific capacitance of 604 F g -1 at the current density of 1 A g -1 . A carbon fiber mat from a different solvent extraction residue also delivered the specific capacitance of 508 F g -1 . These specific capacitance values are comparable to or better than commercial activated carbons, demonstrating the viability of manufacturing carbon nanofiber electrodes from coal without the use of a commercial polymer as binder in the spinning ink.
Ionic conduction in silicate glasses is mainly influenced by the nature, concentration, and mobility of the network-modifying (NWM) cations. The electrical conduction in SLS is dominated by the ionic migration of sodium moving from the anode to the cathode. An activation energy for this conduction process was calculated to be 0.82eV and in good agreement with values previously reported. The conduction process associated to the leakage current and relaxation peak in TSDC for HPFS is attributed to conduction between nonbridging oxygen hole centers (NBOHC). It is suggested that ≡Si-OH = ≡Si-O - + H 0 under thermo-electric poling, promoting hole or proton injection from the anode and responsible for the 1.5eV relaxation peak. No previous TSDC data have been found to corroborate this mechanism. The higher activation energy and lower current intensity for the coated HPFS might be attributed to a lower concentration of NBOHC after heat treatment (Si-OH + OH-Si = SiO-Si + H 2 O). This could explain the TSDC signal around room temperature for the coated HPFS. Another possible explanation could be a redox reaction at the anode region dominating the current response.
A cathode-side contact layer is required to provide and maintain stable electrical conduction paths between the interconnect and cathode in a solid oxide fuel cell (SOFC) stack assembly and thus minimize the ohmic resistance and stack power loss. Current cathode-interconnect contact materials are based on noble metals, electrically-conductive perovskites, their composite materials, etc. These materials are either too expensive or do not possess the overall balanced performance required for the cathode-side contact application. To achieve the DOE SOFC system cost and performance stability goals, a new generation of low-cost, high-performance contact materials needs to be developed. In this project, spinel-based materials thermally converted from the Fe-Ni and Co-Mn based alloy precursors were developed and validated for the cathode-side contact application. The precursor alloy compositions were optimized via a combination of composition screening in the (Ni,Fe) 3 O 4 and (Mn,Co) 3 O 4 spinel system, alloy design using physical metallurgy principles, and cost considerations. The alloy powders with the desired composition and particle size were manufactured via gas atomization. The optimal process parameters for thermal conversion of these alloy precursor layers to a spinel-based layer were identified, i.e., 900°C x 2h in air, which is close to the initial stack firing condition. The area-specific resistances (ASRs) of the interconnect/contact/cathode test assemblies with the developed contact layer were determined for various durations (up to 5000 h) under simulated cathodic operation conditions. Some of the alloy-derived spinel contacts exhibited the lowest ASR and ASR degradation rate. The in-stack performance of the most promising alloy-derived contact layer is currently being evaluated via stack testing. To reduce the stack cost, the Co-Mn based alloy powders were utilized as the precursor for synthesis of dense spinel-based interconnect coating. By optimizing both the initial powder size/distribution and the alloy powder composition, a dense (Mn,Co) 3 O 4 -based spinel coating was achieved. Furthermore, co-sintering of the coating/contact dual-layer structure under the initial stack firing condition was realized by utilizing the tailored Co-Mn alloy precursors. Cost analysis of the developed technology indicated a total stack cost reduction of around 10.6% with the implementation of co-sintering of the interconnect coating and the contact layer during initial stack firing. Since low-cost processes such as screen printing is utilized in the precursor application and no reduction heat treatment is needed for the coating formation, the developed technology can be readily implemented at the industrial partner’s manufacturing facilities with no additional capital investment needed.
The layer-structured Li[Ni x Co y Mn 1-x-y ]O 2 (NCM) cathode materials have been the best choice for increasing electric vehicle driving distance per charge. The high Ni layered oxide represents successfully commercialized NCM cathodes (such as NCM622 and NCA) in lithium-ion batteries (LIBs) for EV applications due to their high energy density and acceptable cycling stability. However, the price of cobalt, the key element within LIBs for stability, has nearly tripled over the past few years due to increased demand from the cell phone industry. As mentioned in the DOE Funding Opportunity Announcement, the current materials shortage will also cause speculation for a future global shortage. Therefore, to meet the requirement and sustainability of the next-generation long-range and low-cost EVs, developing cathode materials with low-Co content to achieve higher energy density and lower cost is both essential and urgent. The overarching objective of this work is to develop stabilized NCM cathode materials with low Co content (namely LiNi x Co y Mn 1-x-y O 2 , y ≤ 0.04) to meet DOE’s goal of reducing Co loading below 50 mg Wh -1 while maintaining energy density greater than 600 Wh kg -1 based on cathode material. Via various dopings and coatings scalable methods, we explored and enhanced the cycling performance of low-cobalt cathodes. The final obtained NCM cathodes paired with graphite anode aim to deliver batteries with a high initial specific energy density of over 240 Wh kg -1 and a low capacity fading rate of less than 20% in 1000 cycles under a C/3 discharge rate. To accomplish this goal, a multidisciplinary team with several co-investigators has been formed from three organizations: The Pennsylvania State University (PSU), Oak Ridge National Laboratory (ORNL), and Pacific Northwest National Laboratory (PNNL). The PI and co-investigators are Dr. Donghai Wang (PI) from PSU with expertise in the synthesis of nanostructured materials and manipulation of interfacial properties of electrochemically active materials, Dr. Jagjit Nanda, with substantial knowledge of and expertise in state-of-the-art cathodes from ORNL, Dr. Chao-Yang Wang with significant experience in advanced cell design and fabrication and cell diagnostics from PSU, and Dr. Chongmin Wang with world-wide known expertise of advance atomic scale characterization of electrode materials from PNNL. Furthermore, this project will leverage and synergistically work with the current DOE-funded programs on battery materials at PSU and ORNL and electrode materials characterization at PNNL. During this funded period, we have accomplished milestones stated as follows: • Scale up production of LiFePO 4 (LFP) coated NCM811 with a production of 300g/batch. Fifteen (≥2 Ah) pouch cells with LFP-coated NCM811 cathode are delivered. Self-evaluated pouch cells in PSU show superior over 80% capacity retention performance even after 1500 cycles at C/3 rate. • Various cations (Al, Ti, Zr, and Mo) substitute cobalt in low-cobalt partially and Co-free cathodes. Their effects on crystal structure and electrochemical behavior are explored. • Phosphate compounds as coating materials represent promising surface protection precursors for low-cobalt cathode materials. Therefore, several metal phosphates were selected for improving the NMC cycling performance and are regarded as effective approaches for a scalable and practical surface protection method. • Production of NCM92, where Nickel content is 92% among transition metals, is scaled up from synthesis to coating and heat treatment procedures. Fifteen 2.7Ah pouch cells with Ti-doped NCM92 cathodes and industrial graphite anode are delivered to Idaho National Lab for testing.
The US will be contributing to the HL-LHC upgrade at CERN with the fabrication and qualification of RFD crabbing cavities in the framework of the HL-LHC Accelerator Upgrade Project (AUP) managed by Fermilab. AUP received Critical Decision 3 (CD-3) approval by DOE in December 2020 launching the project into the production phase. The electro-magnetic design of the cavity was inherited from the LHC Accelerator Research Program (LARP) but needed to be revised to meet new project requirements and to prevent issues encountered during beam tests performed at CERN in the R&D phase. Two prototype cavities were manufactured in industry and cold tested. Challenges specific to the RFD cavity were the stringent interface tolerances, the pole symmetry, and the higher-order-mode impedance spectrum. Chemical pro-cessing and heat treatments were performed initially at FNAL/ANL and are now being transferred to industry for the production phase. HOM dampers are manufactured and validated by JLAB. A summary of cold test results with and without HOM dampers is presented.
To harness the potential of laser powder bed fusion (LPBF) 316H stainless steel (SS) for use in advanced nuclear reactors, extensive research efforts are needed to develop optimal laser processing parameters and appropriate heat treatments, taking into account various manufacturing platforms and locations. Furthermore, it is crucial to assess the material properties in environments relevant to reactor operating conditions. In collaboration with Oak Ridge National Laboratory (ORNL) and Los Alamos National Laboratory (LANL), Argonne National Laboratory (ANL) is dedicated to gaining insights into how the manufacturing process and post-build treatments impact the performance of LPBF 316H SS. This report provides an overview of ANL's research findings for FY23, focusing on LPBF 316H SS produced using a Renishaw AM400 laser system. Specifically, our research has concentrated on three key areas: 1) Optimum laser processing parameters: Leveraging the high-throughput printing technology, we systematically varied the laser power, exposure time and point distance within the same build. By measuring the as-printed porosity, we identified an optimum printing parameter window that produced materials with near-complete density; 2) Post-built treatment development: Materials printed with the optimum laser parameters underwent treatments including stress relief, solution annealing, and hot isostatic pressing. Subsequently, we fabricated tension, creep, and fatigue specimens from materials subjected to these different conditions. Over the next year, a series of scoping tests will be conducted to facilitate the selection of the most suitable post-build treatment condition; 3) Thermal aging effects on microstructure and properties: thermal aging at 550°C, 650°C and 750°C was conducted on LPBF 316H SS specimens up to 2500 h. Microstructural characterization was performed with electron microscopy, and the evolution of the dislocation cell structures and secondary phases was studied. Microhardness tests and tension tests were conducted to quantify changes in mechanical properties. The results revealed that the aged LPBF 316H SS exhibited a high density of Cr-rich and Mo-rich fine precipitates within grains due to the presence of a high density of dislocations and the globally distributed dislocation cell structures, which served as heterogeneous nucleation sites for secondary phases. Along grain boundaries, a Mo-Cr-rich phase, observed in 750°C-aged conditions, displayed significant thermal coarsening. Throughout the aging process, various mechanisms, including stress relaxation, dislocation cell structure recovery, solution hardening, and precipitation hardening, competed to influence materials strength. These results contribute towards establishing the technical basis for qualifying LPBF 316H SS for advanced nuclear reactor applications.
Alnico is a rare-earth free; permanent magnet (PM) which maintains its saturation magnetization while at temperatures up to 550°C but lacks the coercivity and energy product needed for a wide range of demanding applications. With an optimal set of processing and manufacturing techniques, Alnico could replace Dy-free Nd-Fe-B magnets in certain applications if the microstructure is textured in a $\langle$001$\rangle$ direction. Additive manufacturing (AM) of near-net-shape magnets may provide such texture. To investigate the possibility, directed-energy deposition (DED) in conjunction with an actively cooled substrate was used to build samples with a compositionally modified, gas-atomized, Alnico 8 alloy. The resulting samples were solutionized and quenched, followed by magnetic annealing and a heat treatment. Magnetic properties and microstructures are compared to previous work.
Lithium (Li) is one of the critical industrial materials and an indispensable component in manufacturing Li batteries. However, Li resource is limited and geographically uneven in earth’s crust and its mining is not sustainable due to the low efficiency and complicated separation and refining processes. In this work, we develop a one-step technology to electrochemically extract Li from low concentration solutions (brines, seawater or used Li-ion batteries) into a form to directly produce commercial battery materials, eliminating the costly Li separation/purification steps. By using this approach, Li was selectively extracted and converted into battery cathodes (e.g., spinel LiMn 2 O 4 and layered LiNi x Mn y Co z O 2 ) through heat treatment. With the importance of Li-ion batteries to the overall decarbonization strategy, the demonstration of a one-step Li-extraction to a ready-to-use material could expand the access to Li resources at a lower cost by eliminating processing steps.
This report provides experimental details and associated results on the elemental distributions (compositions), crystalline/amorphous phase distributions, and microstructures for iron phosphate reference materials (DPF5-336) made with different cooling curves and starting from different temperatures (i.e., 1050°C and 1200°C). The primary goal of this work was to evaluate the properties of the DPF5- 336 reference material after it was melted and cooled at different rates to simulate the cooling profile of different types of canisters. Crystal fractions across the SCC#2, SCC#3, and SCC#5 samples were all similar ranging in crystal content of 35.66–41.14 mass% with amorphous fractions being the balance (64.34–58.86 mass%, respectively). This shows that the heat treatment profile did not seems to greatly affect either the total crystal content or the phase distributions. The quenched sample was almost completely amorphous (99.55 mass%) with very small peaks identified as Li 3 Fe 2 (PO 4 ) 3 whereas the SCC-treated materials showed peaks for what appear to be ten separate phases present in various concentrations. Another goal of these experiments was to see how the phase distribution affected chemical durability of these waste forms, but that information is being collected at Argonne National Laboratory and will be published in a separate report
High-strength aluminum alloys for elevated temperature applications are desirable to replace heavier and more expensive titanium alloys. However, most aluminum alloys lose a large fraction of their strength at temperatures above approximately 200°C. ORNL has designed DuAlumin-3D, an alloy with nominal composition Al-9Ce-4Ni-0.5Mn-1Zr (wt.%), which utilizes the high cooling rates in additive manufacturing (AM) to achieve a refined microstructure, and thermally stable mechanical properties. DuAlumin-3D was fabricated by laser powder bed fusion and tested for its tensile mechanical properties across a range of temperature, and for its room temperature high-cycle fatigue resistance. The alloy was tested in both the as-printed and heat treated conditions, and both parallel and perpendicular to the AM build direction. The alloy was found to have anisotropic mechanical behavior in the as-printed state, but the anisotropy significantly decreased (both for tensile and fatigue properties) following heat treatment. The tensile properties significantly out-performed benchmark wrought 2219-T61 across a wide temperature range. The room temperature fatigue performance was approximately similar to 2219-T61.
Through this DOE funded 3.5-year research project, feasibility of fabricating supercritical carbon dioxide (sCO2) turbine components by powder metallurgy (PM) based near-net-shape (NNS) hot isostatic pressing (HIP) was demonstrated in a turbine nozzle ring, a turbine casing with Haynes 282 powder, and a bimetallic pipe with Haynes 282 and SS415 powder. As-HIP microstructure of various powders and HIP processing conditions was studied to downselect a condition for the prototype components. Tensile strength and low cycle fatigue (LCF) capability of PM HIP 282 was found to be superior to cast 282, despite a debit in creep stress capability that could be mitigated by component design modification. Near-Net-shape with minimal post machining was achieved by modeling the non-uniform shrinkage during HIP cycle and designing the HIP tooling to meet dimensional targets. The prototypes of turbine nozzle ring and bimetallic pipe were successful in achieving overall dimension, microstructure, and properties, despite dimensional tolerance affected by chemical milling rate. The prototype of a 1700lbs turbine casing was partially successful in achieving dimension, microstructure in as-HIP state, and providing consistent mechanical properties, however, cracking issue during post heat treatment required further investigation. The estimated manufacturing cost using NNS HIP was a ~50% reduction compared to forging with extensive machining, which translated into ~$100/kWe CAPEX cost reduction for concentrated solar power (CSP) power block.
The hot thermal energy storage tanks in many operating (Gen2) concentrating solar power plants are designed to contain molten nitrate solar salt at 565 Degrees Celsius and are constructed from 347H stainless steel (SS). From previous work, it is known that 347H SS weldments are potentially susceptible to stress-relaxation cracking (SRC), particularly in the heat-affected zone above 540 Degrees Celsius when no post-weld heat-treatment (PWHT) is performed. However, residual stresses can be reduced when weldments receive PWHT, while at the same time a crack-resistant microstructure is being generated. The overarching goal of this project was to optimize cost-effective, thickness-dependent, localized PWHT procedures and to investigate for feasible non-destructive evaluation (NDE) at commercial scale for hot tanks in Gen2 CSP using 347H SS.
This research demonstrated the concept of carbide precipitation-strengthened refractory high entropy alloys (RHEA). The advantage of a precipitation strengthened alloy is all phases are in thermodynamic equilibrium promoting microstructural stability, and consequently retention of properties at elevated temperatures. Additionally, as with any precipitation strengthened – or age hardened alloy, components can be heat-treated after manufacturing to manipulate the microstructure and optimize properties for performance. This is an advantage of the precipitation strengthened alloys over composites and ceramics materials, where the microstructure and properties are essentially fixed upon the initial materials manufacturing stage. High throughput (HT), multi-scale computer modeling was used to identifying novel RHEA compositions with desired characteristics needed for precipitation strengthening. The results showed that carbides precipitated and consequently, the strength of the alloys (measured in compression) increased after heat-treatment, which is the desired effect. The project also demonstrated the feasibility of producing articles from RHEA by additive manufacturing (AM).