Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GASOLINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

CO 2 hydrogenation: Selectivity control of CO versus CH 4 achieved using Na doping over Ru/m-ZrO 2 at low pressure

By doping 1%Ru/m-ZrO 2 with sodium, selectivity tuning between CO and CH 4 during CO 2 hydrogenation was achieved by controlling the relative rates of reverse water-gas shift and CO methanation. By increasing basicity through Na loading: (1) the formate C-H bond is weakened in DRIFTS of adsorbed CO, accelerating C-H bond formation of formate and promoting CO formation at the Ru/m-ZrO 2 interface; and (2) the coverage of Na increases on ensembles of Ru atoms responsible for methanation. Increasing Na content shifts selectivity from CH 4 (useful for synthetic natural gas) to CO, which can be used for Fischer-Tropsch synthesis or methanol-to-gasoline. Electronic modification of formate is likely due to enhanced basicity (strengthening bonding between catalyst and the-CO 2 function of formate and weakening C-H). In conclusion, no electron transfer from Na to Ru was detected in XANES. DRIFTS as a function of time and XPS results showed that Na exacerbates site blocking and deactivation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of framework Al pairing on NO storage properties of Pd-CHA passive NOx adsorbers

For this study, three Pd/H-CHA samples were prepared containing 53.0%, 10.8% and 6.5% paired Al sites at near fixed Si/Al ratio and similar Pd loading. According to H 2 temperature-programmed reduction, Pd was present almost exclusively as isolated cations in the two samples containing the higher concentrations of paired Al sites, whereas in the other sample PdO was also present. Simulated lean cold start tests on the fresh samples conducted in a microflow reactor showed that the sample containing PdO stored the lowest amount of NOx. When tested with CO/H 2 , the sample containing 53.0% paired Al sites showed significantly better storage capacity than the other samples and deactivated less rapidly upon sequential tests. Experiments using lean gasoline engine exhaust revealed similar trends. This study showed that a high concentration of paired Al sites in Pd/H-CHA is beneficial for NOx storage capacity, thermal durability, and minimizing deactivation in the presence of CO/H 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Powders and pellets – Extrusion engineering for a Cu/BEA syngas-to-hydrocarbons catalyst

Converting high-performing powder catalysts from the laboratory reactor scale into effective extruded catalysts at the industrial scale remains a hurdle for advancing sustainable catalytic processes, such as the conversion of biogenic syngas into high octane gasoline. Recently, a process-intensified syngas-to-hydrocarbons (STH) reaction in a single reactor under relatively mild conditions (220–250 ºC, 0.75–2.0 MPa) was reported, enabled by the development of a dimethyl ether (DME) homologation catalyst, Cu-modified H-BEA (Cu/BEA) zeolite. In this study, we explore approaches for synthesizing engineered Cu/BEA catalysts for use in the STH reaction to retain the high performance observed with the powder catalyst. We demonstrate that changes to the order of manufacturing steps (i.e., Cu deposition, alumina binder addition, and extrusion) result in observable changes to key active sites (Brønsted acid sites and zeolitic Cu + species), and ultimately, catalyst performance. When the Cu precursor was added directly to BEA before extrusion, both types of active sites were stabilized, preserving the activity of the powder catalyst. However, when the Cu precursor was added after extrusion, the resulting Cu species were mobile, destabilizing Brønsted acid sites and leading to near-zero activity.

09 BIOMASS FUELS↗

Bioalcohol production from acidogenic products via a two-step process: A case study of butyric acid to butanol

This article presents the full study (lab-scale experimental study and large-scale techno-economic analysis) results of a two-step catalytic process for the conversion of organic waste–derived butyric acid to butanol. Butanol from biomass resources like organic waste promise to become an attractive and sustainable fuel and industrial precursor due to an increase in greenhouse gas content in the atmosphere. Therefore, research in this field is important for energy applications and reduction in greenhouse gas emissions. In this regard, a two-step process was applied in this study to produce butanol from butyric acid that can potentially be derived from organic waste. The two-step process consists of the (1) esterification of butyric acid to methyl butyrate and (2) hydrogenolysis of this methyl butyrate to butanol. The first reaction, esterification of butyric acid, was optimized using carbon-based catalysts. The production of butanol from methyl butyrate via hydrogenolysis was investigated using bimetallic Pt–Co catalysts. The hydrogenolysis of methyl butyrate on these catalysts under optimal conditions of 250 °C, 5 MPa H 2 , and a feed/catalyst weight ratio of 11.2 led to 54.1% selectivity toward 1-butanol. Based on the experimental results, an integrated process simulation model was developed to determine the economic potential of the two-step production of butanol from butyric acid. Using this model, the techno-economic feasibility of the two-step process was analyzed. Here, the minimum selling price (MSP) of 1-butanol produced from butyric acid using this process was US dollars 3.388 per gallon of gasoline equivalent (GGE). This MSP is in the range of recent biofuel market prices of US dollars 2.03/GGE to US dollars 3.83/GGE.

09 BIOMASS FUELS↗

Reactivity of novel high-performance fuels on commercial three-way catalysts for control of emissions from spark-ignition engines

The Department of Energy “Co-Optimization of Fuels and Engines” initiative aims to simultaneously develop novel high-performance fuels with advanced engine designs to reduce petroleum consumption. To achieve commercialization, advanced engines running on alternative fuels still must meet emissions regulations. Warm three-way catalysts (TWC) are very effective at meeting the stringent emissions regulations on pollutants such as nitrogen oxides (NOx), non-methane organic gases (NMOG) and carbon monoxide (CO) from gasoline-fueled spark-ignition (SI) engines operating under stoichiometric conditions; thus, most SI engine emissions occur during cold-start, when the TWC has not yet achieved light-off. In the current study, the light-off behavior of novel high-performance fuel candidates has been investigated on a hydrothermally-aged commercial TWC using a synthetic engine-exhaust flow reactor system according to industry guidelines. Over 30 potential fuel components were examined in this study, including alkanes, alkenes, alcohols, ketones, esters, aromatic ethers, and non-oxygenated aromatic hydrocarbons. Short-chain acyclic oxygenates, including alcohols, ketones, and esters, tended to light off at relatively low temperatures, while alkenes, aromatics, and cyclic oxygenates tended to light off at relatively high temperatures. The light-off behavior of alkanes and alkenes depended strongly on their size and structure. In terms of the influence on CO light-off on the TWC, the fuels fell into two distinct categories: (i) non-inhibiting species including C 2 -C 3 alcohols, alkanes, acyclic ketones, and esters; and (ii) inhibiting species including alkenes, aromatic hydrocarbons, cyclic oxygenates, and C 4 alcohols.

33 ADVANCED PROPULSION SYSTEMS↗

Multiple injection for improving knock, gaseous and particulate matter emissions in direct injection SI engines

Advances in fuel injector technology have enabled research and development on a large variety of direct injection spark ignition (DISI) engine fueling strategies targeted to improve engine performance and reduce engine-out emissions. This study explores the effect of multiple injections on knock, engine efficiency and stability, and particulate number and gaseous emissions on a single-cylinder DISI research engine. Work to date on multiple injections in the literature is reviewed, and then two aspects of multiple injection strategies are experimentally investigated: the number of injections (up to five times in a cycle); and the timing of the injections (classified relative to the timing of intake valve opening and closing). A boosted, single-cylinder research engine equipped with a state-of-the-art piezoelectric hollow cone spray direct injector and research-grade E10 gasoline was used for the study. The results show multiple injections maintain torque and combustion stability compared with single injection and slightly increase the knock limits and indicated thermal efficiencies (maximum 0.7% absolute, 2.8% relative compared with single-injection baseline) due to improved heat release phasing, especially with an additional late injection during the intake valve closed (compression stroke) period. The gaseous pollutant emissions including nitrogen oxides and unburned hydrocarbons were reduced by 25% with multiple injections, particularly with injection during the compression stroke. In contrast, carbon monoxide emissions increased with multiple injections for all conditions. Increasing the number of injection events significantly reduced particulate number emissions (half with each additional injection), and the decrease in particulate number was not sensitive to the injection timing.

42 ENGINEERING↗

Replacing liquid fossil fuels and hydrocarbon chemical feedstocks with liquid biofuels from large-scale nuclear biorefineries

Liquid fossil fuels (1) enable transportation and (2) provide energy for mobile work platforms and (3) supply dispatchable energy to highly variable demand (seasonal heating and peak electricity). We describe a system to replace liquid fossil fuels with drop-in biofuels including gasoline, diesel and jet fuel. Because growing biomass removes carbon dioxide from the air, there is no net addition of carbon dioxide to the atmosphere from burning biofuels. In addition, with proper management, biofuel systems can sequester large quantities of carbon as soil organic matter, improving soil fertility and providing other environmental services. In the United States liquid biofuels can potentially replace all liquid fossil fuels. The required system has two key features. First, the heat and hydrogen for conversion of biomass into high-quality liquid fuels is provided by external low-carbon energy sources--nuclear energy or fossil fuels with carbon capture and sequestration. Using external energy inputs can almost double the energy content of the liquid fuel per unit of biomass feedstock by fully converting the carbon in biomass into a hydrocarbon fuel. Second, competing effectively with fossil fuels requires very large biorefineries—the equivalent of a 250,000 barrel per day oil refinery. This requires commercializing methods for converting local biomass into high-density storable feedstocks that can be economically shipped to large-scale biorefineries.

09 - BIOMASS FUELS↗

Evaluating long-term emission impacts of large-scale electric vehicle deployment in the US using a human-Earth systems model

While large-scale adoption of electric vehicles (EVs) globally would reduce carbon dioxide (CO 2 ) and traditional air pollutant emissions from the transportation sector, emissions from the electric sector, refineries, and potentially other sources would change in response. Here, a multi-sector human-Earth systems model is used to evaluate the net long-term emission implications of large-scale EV adoption in the US over widely differing pathways of the evolution of the electric sector. Our results indicate that high EV adoption would decrease net CO 2 emissions through 2050, even for a scenario where all electric sector capacity additions through 2050 are fossil fuel technologies. Greater net CO 2 reductions would be realized for scenarios that emphasize renewables or decarbonization of electricity production. Net air pollutant emission changes in 2050 are relatively small compared to expected overall decreases from recent levels to 2050. States participating in the Regional Greenhouse Gas Initiative experience greater CO 2 and air pollutant reductions on a percentage basis. These results suggest that coordinated, multi-sector planning can greatly enhance the climate and environmental benefits of EVs. Additional factors are identified that influence the net emission impacts of EVs, including the retirement of coal capacity, refinery operations under reduced gasoline demands, and price-induced fuel switching in residential heating and in the industrial sector.

54 ENVIRONMENTAL SCIENCES↗

SAF: a promising approach to meet growing jet fuel demand

SAF provides a promising approach to aid the rising jet fuel demand from increased travel around the world and reduce the lifecycle emissions from the aviation sector. Although the feasibility of SAF pathways has been demonstrated through economic and environmental metrics quantification, the models used to quantify these variables have a high degree of variability in terms of accuracy and thereby reliability. To understand how to adopt and commercialize SAF, we need to harmonize these process models and assess metrics and technical limitations related to their production technologies. We find the production cost of SAF using hydro processed fatty acids and esters (HEFA), Fischer-Tropsch (FT), and alcohol-to-jet (ATJ) to be $\$$3-$\$$6/gallon gasoline equivalent (gge) and life cycle emissions to be lower than Jet A, except for ATJ using corn grain (≤25%). HEFA utilizing oil feedstocks has the lowest production cost (~$\$$2.9/gge) and highest jet yield (>150 gge/dry ton), while FT has the largest emission reduction (94%) compared to fossil jet. A unique contribution of this study is a comparative analysis of metrics related to SAF processes across technical, economic, and sustainability aspects. A cross-comparison of these metrics shows HEFA using fats, oils, and grease have the most favorable ratings, while HEFA using algae and ATJ using corn stover have more neutral and unfavorable ratings, respectively. These ratings can be improved by implementing the right combination of practical and technological advancements.

09 BIOMASS FUELS↗

Piston geometry and stroke optimization for high efficiency propane spark ignition engines

Propane has unique properties and offers interesting characteristics for high-efficiency spark ignition engines. Its high volatility reduces or completely eliminates fuel-wall wetting and facilitates fuel air mixing. Furthermore, propane has a research octane number of 112 and a high octane sensitivity of 15. Finally, its laminar flame speed is on the same order as that of conventional gasoline, and it exhibits high dilution tolerance. Modern spark ignition internal combustion engines rely on fast combustion rates and high dilution to achieve high brake thermal efficiencies. To accomplish this, high stroke-to-bore ratios and high geometric compression ratios have been used in new engine designs. Therefore, propane’s relatively high laminar flame speeds, high knock resistance, and dilution tolerance make it an excellent candidate fuel for modern spark ignition engines. The objective of this work is to co-optimize the piston geometry and the engine stroke to maximize the efficiency of a spark-ignition engine fueled with propane. 3D computational fluid dynamics (CFD) simulations employing the extended coherent flamelet model were used to study the parametric effects of piston shape and stroke length. A piston geometry based on high performing pistons was parameterized using four controlling parameters. The piston geometry and engine stroke design space was explored using deterministic and quasi-random sampling techniques. In conclusion, a Gaussian process regression model was built using the simulation data to explain the results observed.

33 ADVANCED PROPULSION SYSTEMS↗

Numerical investigation of equivalence ratio effects on Flex-Fuel mixing controlled combustion enabled by prechamber ignition

There is interest in adapting renewable and low-carbon intensity fuels to heavy-duty engines to help displace criteria and greenhouse gas emissions associated with diesel combustion. Low-carbon fuels have inherently low cetane numbers and thus pose a significant challenge when considering direct substitution in diesel combustion systems. Use of an actively fueled prechamber as an ignition source to initiate mixing-controlled combustion (PC-MCC) of low-cetane fuels is becoming an attractive combustion mode to alleviate the identified reactivity deficit. This work focuses on the utilization of an active prechamber to facilitate diesel-like combustion of bioethanol-gasoline fuel blends in a heavy-duty engine. Recent results in this emerging technology suggest that ignition quality is uniquely coupled to prechamber equivalence ratio. In this numerical study, the fundamental implications of prechamber equivalence ratio on the ignition performance of direct injected fuels ranging from E10 to E100 are investigated using CONVERGE. Parametric studies of the prechamber operating strategy were assessed at diesel-like conditions to characterize the performance trends relative to a diesel baseline at the same boundary conditions. Simulation results indicate that PC-MCC is flex-fuel capable and achieves diesel-like ignition qualities and combustion processes for all fuels considered under stoichiometric and rich prechamber conditions. To characterize the equivalence ratio trends observed, a novel inflow boundary modeling technique was utilized to prescribe turbulent jets in place of the prechamber where selective speciation of the jet composition was conducted to isolate the ignition contributions of radical and reacting species in lean, stoichiometric, and rich jets. The inflow boundary modeling suggests that excess fuel and combustion intermediates present in jets produced from stratified and fuel-rich prechamber operation promotes higher jet temperatures and as such are superior ignition sources. Relative to a lean prechamber jet, the peak temperature of a reacting jet from a rich prechamber was up to 600 K hotter at fixed distances from the orifice exit. Furthermore, radicals also demonstrated an influence on the ignition process, but the combustion mode was identified to be thermally dominant.

33 ADVANCED PROPULSION SYSTEMS↗

Unlocking the biofuel power of cover crop in Washington State: Enhancing potential through hydrothermal liquefaction

This study evaluates cover crops in Washington State (WA) as a renewable feedstock for hydrothermal liquefaction (HTL), supported by techno-economic (TEA) and life cycle (LCA) analysis. In the Pacific Northwest, fallow land is the common winter practice, generating no income for farmers. Over three years, field trials at two representative sites—Puyallup (cool, wet) and Othello (irrigated, no-till)tested triticale, hairy vetch, crimson clover, winter pea, and fava bean preceding cash crops. Biomass yields, composition, soil impacts, and net revenue were assessed across removal treatments. HTL conversion produced 32–37 wt% biocrude, lower than 48 wt% for sewage sludge, with modeled cradle-to-grave carbon intensities of 26–31 g CO 2 e/MJ and minimum fuel selling prices (MFSP) of $\$$6.75–$\$$7.18 per gallon gasoline equivalent (GGE), comparable to other lignocellulosic feedstocks. No significant changes were observed in soil carbon, nitrogen, or subsequent cash crop yields after cover crop removal. Farmer profitability was possible, particularly for triticale and hairy vetch at $\$$60 per dry ton. To address seasonal variability, blending with wastewater sludge was evaluated. All scenarios delivered >70 % carbon intensity reductions relative to fossil fuels, and with Renewable Identification Number (RIN) credits, MFSPs below $\$$2.5 GGE were achievable. These results demonstrate that cover crops can generate new revenue streams for farmers while serving as a flexible, low-carbon feedstock. Integrating cover crops with waste biomass offers a practical pathway to expand the bioeconomy and support year-round renewable fuel production.

Biofuels↗

A low-cost solid–liquid separation process for enzymatically hydrolyzed corn stover slurries

Solid-liquid separation of intermediate process slurries is required in some process configurations for the conversion of lignocellulosic biomass to transportation fuels. Thermochemically pretreated and enzymatically hydrolyzed corn stover slurries have proven difficult to filter due to formation of very low permeability cakes that are rich in lignin. Treatment of two different slurries with polyelectrolyte flocculant was demonstrated to increase mean particle size and filterability. Filtration flux was greatly improved, and thus scaled filter unit capacity was increased approximately 40-fold compared with unflocculated slurry. Although additional costs were accrued using polyelectrolyte, techno-economic analysis revealed that the increase in filter capacity significantly reduced overall production costs. Fuel production cost at 95% sugar recovery was reduced by $1.35 US per gallon gasoline equivalent for dilute-acid pretreated and enzymatically hydrolyzed slurries and $3.40 for slurries produced using an additional alkaline de-acetylation preprocessing step that is even more difficult to natively filter.

09 BIOMASS FUELS↗

Enhanced crude oil depletion by constructed bacterial consortium comprising bioemulsifier producer and petroleum hydrocarbon degraders

The aim of this work was to study the production of bioemulsifier by Rhodococcus erythropolis OSDS1, and the improvement of crude oil depletion efficiency using a consortium of petroleum hydrocarbon degraders and OSDS1. The results showed that R. erythropolis OSDS1 produced highly stable bioemulsifier under various salinity (0-35 g/L NaCl) and pH (5.0-9.0) conditions; more than 90% of the initial emulsification activity was retained after 168 h. Emulsification capacity of the bioemulsifier on different petroleum hydrocarbons was diesel > mineral oil/crude oil > gasoline. A mixed bacterial consortium combining OSDS1 and four other petroleum hydrocarbon degraders was constructed. GC-MS results revealed that the constructed consortium achieved 85.26% depletion efficiency of crude oil in 15 days, which was significantly higher than that of individual strains. During the process, we observed alkane hydroxylase gene ( alkB ) was successfully amplified from the consortium, confirming presence of crude oil degrading enzymes.

02 PETROLEUM↗

The selective catalytic reduction of NO x over Ag/Al 2 O 3 with isobutanol as the reductant

Here, this study investigates the potential of isobutanol (iBuOH) as a reductant for the selective catalytic reduction (SCR) of NO x over 2 wt% Ag/Al 2 O 3 between 150 and 550 °C and gas hourly space velocities (GHSV) between 10,000 and 35,000 h -1 . The feed gas consists of 500 ppm NO, 5% H 2 O, 10% O 2 , and 375-1500 ppm iBuOH (C 1 :N ratios of 3-12); additionally, blends of 24 and 48% iBuOH in gasoline are evaluated. Over 90% NO x conversion is achieved between 300 and 400 C using pure iBuOH, including a 40% peak selectivity towards NH 3 that could be utilized in a dual HC/NH 3 SCR configuration. The iBuOH/gasoline blends are only able to achieve greater than 90% NOx conversion when operated at a GHSV of 10,000 h -1 and employing a C 1 :N ratio of 12. Iso-butyraldehyde and NO 2 appear to function as intermediates in the iBuOH-SCR mechanism, which mirrors the mechanism observed for EtOH-SCR. In general, the performance of iBuOH in the SCR of NO x over a Ag/Al 2 O 3 catalyst is comparable with that of EtOH, although EtOH/gasoline blends display higher NO x reduction than iBuOH/gasoline blends. The key parameter in employing alcohols in SCR appears to be the C-OH:N ratio rather than the C 1 :N ratio.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗