Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Flight Control System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Flight investigation of various control inputs intended for parameter estimation

An experiment assessing the stability and control derivatives resulting from various control inputs was undertaken using the F-8 digital fly by wire aircraft. Improved control inputs have been proposed as a means of making stability and contol derivative estimation more efficient, thus reducing the cost of flight testing and data analysis. The subject inputs were either generated by the pilot or preprogrammed in a remote ground computer and telemetered to the aircraft. Nine preprogrammed inputs and three pilot generated inputs were assessed at subsonic and supersonic flight conditions, and both unaugmented and highly augmented flight control systems were used. Effects of input amplitude were also assessed. The inputs were divided into two general types - sinusoidal or with corners (a rapid and distinct change in slope). The inputs with corners, performed in the unaugmented mode, produced the best sets of stability and control derivatives. The simplest of these inputs, the pilot generated doublet, produced sets of derivatives as good as those produced by the more complex inputs. Small inputs produced worse derivatives than the unaugmented mode, and sinusoidal inputs produced worse derivatives than corner containing inputs.

Shafer, M. F.↗

On requirements for software fault tolerance for flight controls

The need for the application of software fault tolerance techniques in digital flight control systems is argued to follow from the requirements derivable from the safety constraints of such systems, requirements which can be stated in terms of minimum acceptable system reliability levels and, moreover, stated quantitatively. It is argued further that, while fault tolerance appears to be a viable mechanism in general, individual fault tolerance schemes need to be analyzed to ensure that they are adequate to the task and being properly utilized, that such analysis is essentially an exercise in software 'reliability' estimation involving software characteristics not currently included in software 'reliability' modeling (most especially, the degree of correlation of malfunctions among redundant, dissimilar software modules), and that, consequently, further research and studies in the characterization of software behavior and malfunctions is required.

Migneault, G. E.↗

Flight investigation of various control inputs intended for parameter estimation

NASA's F-8 digital fly-by-wire aircraft has been subjected to stability and control derivative assessments, leading to the proposal of improved control inputs for more efficient control derivative estimation. This will reduce program costs by reducing flight test and data analysis requirements. Inputs were divided into sinusoidal types and cornered types. Those with corners produced the best set of stability and control derivatives for the unaugmented flight control system mode. Small inputs are noted to have provided worse derivatives than larger ones.

Shafer, M. F.↗

A variable structure approach to robust control of VTOL aircraft

This paper examines the application of variable structure control theory to the design of a flight control system for the AV-8A Harrier in a hover mode. The objective in variable structure design is to confine the state trajectories to a subspace of the total state space. The motion in this subspace is insensitive to system parameter variations and external disturbances that lie in the range space of the control. A switching type of control law results from the design procedure. The control system was designed to track a vector-valued velocity command. For comparison, a proportional controller was designed using optimal linear regulator theory. Both controllers were evaluated for their transient response performance using a linear model; then a nonlinear simulation study of a hovering approach to landing was conducted. The variable structure controller outperformed its linear counterpart in the presence of wind disturbances and plant parameter uncertainties afforded by the simulation.

Calise, A. J.↗

Flexible Airframe Response Program

Generalized set of flexible vehicle equations-of-motion (EOM's) developed and incorporated into Flexible Airframe Response (FAR) program. Output from FAR program used in aircraft flight control system design.

Lin, C.↗

Closing the design loop on HiMAT (highly maneuverable aircraft technology)

The design methodology used in the HiMAT program and the wind tunnel development activities are discussed. Selected results from the flight test program are presented and the strengths and weaknesses of testing advanced technology vehicles using the RPV concept is examined. The role of simulation on the development of digital flight control systems and in RPV's in particular is emphasized.

Putnam, T. W.↗

Space shuttle handling qualities

The initial Orbiter handling qualities requirements, their effect on the vehicle design, and how it all turned out through the first six orbital missions are reviewed. Specific areas consisting of hand controller considerations and the wheelie problem are discussed. The requirements for the pitch axis subsonic flight control system are reviewed. Results of recent simulator evaluations to compare the existing system at landing with several other configurations are presented.

Gilbert, D. W.↗

Design and test of a four channel motor for electromechanical flight control actuation

To provide a suitable electromagnetic torque summing approach to flight control system redundancy, a four channel motor capable of sustaining full performance after any two credible failures was designed, fabricated, and tested. The design consists of a single samarium cobalt permanent magnet rotor with four separate three phase windings arrayed in individual stator quadrants around the periphery. Trade studies established the sensitivities of weight and performance to such parameters as design speed, winding pattern, number of poles, magnet configuration, and strength. The motor electromagnetically sums the torque of the individual channels on a single rotor and eliminate complex mechanical gearing arrangements.

Source record↗

New results in fault latency modelling

The test design and results from assessment of the performance of the self-test program and the extent of fault latency in a redundant flight control system (FCS) are reported. Assembly language programming generated gate-level faults directed to every avionics component. Details of the fault-simulation software are described, noting the input needed to match the five control-surface parameters managed by the FCS. Most faults were immediately detected, and component-level faults, occurring at pins, were more easily noted than gate-level faults. The results indicated that a 200-word self-test program is sufficient to obtain a fault coverage of 85 percent. Minor hardware changes are required to reach levels over 90 percent.

Mcgough, J. G.↗

On the identification of a highly augmented airplane

The results of applying linear least squares and maximum likelihood estimation procedures to flight data from the AFTI/F-16 airplane are presented. Data from two flight control system modes are analyzed. It is shown that though a simple aerodynamic model structure is adequate for the simple mode, a more complicated model is necessary to adequately describe the highly augmented mode. The effect of augmentation of roll control is shown to be visible in the control parameters.

Batterson, J. G.↗

Optimal disturbance suppression with application to wind shear

A novel quadratic cost function composed of stochastic and deterministic contributions is used in the design of a digital flight control system for a small commercial jet with wind shear present. The optimal output feedback control design is configured to suppress the effect of the wind shear disturbance and maintain closed loop stability. A new algorithm is presented for finding the feedback gain. A proportional-integral control design with wind shear suppression is tested in a detailed nonlinear simulation of a commercial jet during the landing approach.

Broussard, J. R.↗

Rotorcraft simulation at Ames

Attention is given to rotorcraft simulation experience at NASA's Ames research facility, which has involved complex mathematical modeling, high computational capability requirements, and strong influences from pilot motion and visual cues. A development history and performance assessment is presented for the rotorcraft simulation hardware, together with projections of near term development improvements of capabilities. Greater demand is anticipated for the simulation of all-digital helicopter flight control systems.

Alderete, T. S.↗

Blending Gyro Signals To Improve Control Stability

Interference by structural vibrations reduced by adding signals from spatially separated gyros. Technique involves blending signals from rate gyroscopes located at different parts of structure to obtain composite signal that more nearly represents rotation of entire structure. Aircraft vibrations perpendicular to pitch axis contribute to rotations sensed by pitch-rate gyros. Proper blending of signals from gyros suppress contribution of dominant vibrational mode. Most likely applications of concept are flight-control systems for aircraft.

J. F. L. Lee↗

Performance of a commercial transport under typical MLS noise environment

The performance of a 747-200 automatic flight control system (AFCS) subjected to typical Microwave Landing System (MLS) noise is discussed. The performance is then compared with the results from a previous study which had a B747 AFCS subjected to the MLS standards and recommended practices (SARPS) maximum allowable noise. A glide slope control run with Instrument Landing System (ILS) noise is also conducted. Finally, a linear covariance analysis is presented.

Ho, J. K.↗

Extensions to PIFCGT: Multirate output feedback and optimal disturbance suppression

New control synthesis procedures for digital flight control systems were developed. The theoretical developments are the solution to the problem of optimal disturbance suppression in the presence of windshear. Control synthesis is accomplished using a linear quadratic cost function, the command generator tracker for trajectory following and the proportional-integral-filter control structure for practical implementation. Extensions are made to the optimal output feedback algorithm for computing feedback gains so that the multirate and optimal disturbance control designs are computed and compared for the advanced transport operating system (ATOPS). The performance of the designs is demonstrated by closed-loop poles, frequency domain multiinput sigma and eigenvalue plots and detailed nonlinear 6-DOF aircraft simulations in the terminal area in the presence of windshear.

Broussard, J. R.↗

X-29A advanced technology demonstrator program overview

The present discussion of the X-29A forward-swept wing experimental aircraft's functional flight program and concept evaluation program gives attention to the program management structure for a test team that encompasses NASA, the U.S. Air Force, and the prime contractor for the X-29A. The preflight, flight-functional, envelope-expansion and flight research test objectives of the program are also noted, together with the qualitative characterizations obtained to date for both a limited envelope flight control system and one for an expanded envelope.

Sefic, W. J.↗

Real-time open-loop frequency response analysis of flight test data

A technique has been developed to compare the open-loop frequency response of a flight test aircraft real time with linear analysis predictions. The result is direct feedback to the flight control systems engineer on the validity of predictions and adds confidence for proceeding with envelope expansion. Further, gain and phase margins can be tracked for trends in a manner similar to the techniques used by structural dynamics engineers in tracking structural modal damping.

Bosworth, J. T.↗

Piloted simulator study of allowable time delays in large-airplane response

A piloted simulation was performed to determine the permissible time delay and phase shift in the flight control system of a specific large transport-type airplane. The study was conducted with a six degree of freedom ground-based simulator and a math model similar to an advanced wide-body jet transport. Time delays in discrete and lagged form were incorporated into the longitudinal, lateral, and directional control systems of the airplane. Three experienced pilots flew simulated approaches and landings with random localizer and glide slope offsets during instrument tracking as their principal evaluation task. Results of the present study suggest a level 1 (satisfactory) handling qualities limit for the effective time delay of 0.15 sec in both the pitch and roll axes, as opposed to a 0.10-sec limit of the present specification (MIL-F-8785C) for both axes. Also, the present results suggest a level 2 (acceptable but unsatisfactory) handling qualities limit for an effective time delay of 0.82 sec and 0.57 sec for the pitch and roll axes, respectively, as opposed to 0.20 sec of the present specifications for both axes. In the area of phase shift between cockpit input and control surface deflection,the results of this study, flown in turbulent air, suggest less severe phase shift limitations for the approach and landing task-approximately 50 deg. in pitch and 40 deg. in roll - as opposed to 15 deg. of the present specifications for both axes.

Grantham, William D.↗