SEARCH · Engineering Papers

Results for “Fans”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Effects of Simulated Flight on Fan Noise Suppression

Attenuation properties of three treated fan inlets were evaluated. Tunnel flow simulated the inflow clean-up effect on source noise observed in flight and allowed observation of the blade passage frequency tone cut-off phenomenon. Acoustic data consisted of isolated inlet noise measured in the far field at two fixed positions and with traverses at four frequencies. Attenuation and source noise properties with and without flight simulation are compared and discussed. Averaged attenuation properties showed relative agreement of the inlets with their design intent, however, tunnel flow significantly affected the attenuation spectra.

Heidmann, M. F.↗

NASA NTRS1977

Fan inlet for a V/STOL airplane

An inlet was designed for a tilt nacelle lift/cruise fan. A complete set of low speed data was obtained with a 38-cm diameter cold-flow model, and a partial set of data was obtained with a 140-cm-diameter inlet coupled to a high bypass turbofan. The results indicate that a fixed-geometry inlet is a viable concept for the proposed application. Analyses of the data demonstrate that at high angles of incidence and at low airflow rates inlet-flow separation is strongly sensitive to Reynolds number and, consequently, the large-scale inlet has a significantly greater range of separation-free operation.

Koncsek, J. L.↗

NASA NTRS1977

Inlet turbulence and fan noise measured in an anechoic wind tunnel and statically with an inlet flow control device

Turbulence and acoustic measurements were taken in the NASA-Lewis anechoic wind tunnel - a facility which has demonstrated the blade passage tone cutoff phenomena with forward velocity. Turbulence data were taken in a subsonic inlet at various fan speeds under static and forward velocity conditions. A honeycomb/screen flow control device was placed over the inlet during static tests to modify the inflow in an attempt to simulate flight conditions. Acoustic levels of the blade passage tone along with transverse turbulence intensities were reduced with forward velocity. The flow control device reduced the blade passage tone to an intermediate level between those levels associated with static and forward velocity operation.

Shaw, L. M.↗

NASA NTRS1977

The influence of the inlet duct contour on forward radiated fan noise

Measurements have been obtained to determine the extent to which the shape of the inlet duct affects the directivity pattern of forward radiated noise from aircraft gas turbine engines. The test program was conducted using a model fan to which were attached any of three inlet ducts with each designed to cause a particular noise directivity pattern. Existing information on the effects of wave refraction in inlet-type flow fields was used to design the duct contours. Results indicated that the shape of the inlet duct strongly influenced the radiated noise field but that wave refraction was not the dominant factor in controlling the noise directivity pattern.

Sloan, D.↗

NASA NTRS1977

Reliability analysis of forty-five strain-gage systems mounted on the first fan stage of a YF-100 engine

The reliability of 45 state-of-the-art strain gage systems under full scale engine testing was investigated. The flame spray process was used to install 23 systems on the first fan rotor of a YF-100 engine; the others were epoxy cemented. A total of 56 percent of the systems failed in 11 hours of engine operation. Flame spray system failures were primarily due to high gage resistance, probably caused by high stress levels. Epoxy system failures were principally erosion failures, but only on the concave side of the blade. Lead-wire failures between the blade-to-disk jump and the control room could not be analyzed.

Holanda, R.↗

NASA NTRS1978

Cold-air performance of a tip turbine designed to drive a lift fan

Performance was obtained over a range of speeds and pressure ratios for a 0.4 linear scale version of the LF460 lift fan turbine with the rotor radial tip clearance reduced to about 2.5 percent of the rotor blade height. These tests covered a range of speeds from 60 to 140 percent of design equivalent speed and a range of scroll inlet total to diffuser exit static pressure ratios from 2.6 to 4.2. Results are presented in terms of equivalent mass flow, equivalent torque, equivalent specific work, and efficiency.

Haas, J. E.↗

NASA NTRS1978

Filament-winding fabrication of QCSEE configuration fan blades

The design and fabrication of twelve NASA-QCSEE type composite fan blades utilizing wet filament winding fabrication techniques is described. All composite fibers were continuous and attached to the root end. All components were formed, bonded, and co-cured in one molding process. Advanced fiber materials used in the blade fabrication were Thornel-300, Carbolon Z-2-1, and Carbolon Z-3 graphite in an epoxy resin matrix.

Yao, S.↗

NASA NTRS1977

Study of the application of an implicit model-following flight controller to lift-fan VTOL aircraft

An implicit model-following flight controller is proposed. This controller is relatively simple in concept: it provides an input/output relationship that is approximately that of any selected second order system; it provides good gust alleviation; and it is self-trimming. The flight controller was applied to all axes of a comprehensive mathematical model of a lift-fan V/STOL transport. Power management controls and displays were designed to match the various modes of control provided by the flight controller. A piloted simulation was performed using a six degree of freedom simulator. The fixed-operating-point handling qualities throughout the powered lift flight envelope received pilot ratings of 3-1/2 or better. Approaches and vertical landings in IFR zero-zero conditions received pilot ratings varying from 2-1/2 to 4 depending on the type of approach and weather conditions.

Merrick, V. K.↗

NASA NTRS1977

Method of fan sound mode structure determination

A method for the determination of fan sound mode structure in the Inlet of turbofan engines using in-duct acoustic pressure measurements is presented. The method is based on the simultaneous solution of a set of equations whose unknowns are modal amplitude and phase. A computer program for the solution of the equation set was developed. An additional computer program was developed which calculates microphone locations the use of which results in an equation set that does not give rise to numerical instabilities. In addition to the development of a method for determination of coherent modal structure, experimental and analytical approaches are developed for the determination of the amplitude frequency spectrum of randomly generated sound models for use in narrow annulus ducts. Two approaches are defined: one based on the use of cross-spectral techniques and the other based on the use of an array of microphones.

Pickett, G. F.↗

NASA NTRS1977

Method of fan sound mode structure determination computer program user's manual: Modal calculation program

A computer user's manual describing the operation and the essential features of the Modal Calculation Program is presented. The modal Calculation Program calculates the amplitude and phase of modal structures by means of acoustic pressure measurements obtained from microphones placed at selected locations within the fan inlet duct. In addition, the Modal Calculation Program also calculates the first-order errors in the modal coefficients that are due to tolerances in microphone location coordinates and inaccuracies in the acoustic pressure measurements.

Pickett, G. F.↗

NASA NTRS1978

Compressor and fan wake characteristics

A triaxial probe and a rotating conventional probe, mounted on a traverse gear operated by two step motors were used to measure the mean velocities and turbulence quantities across a rotor wake at various radial locations and downstream stations. The data obtained was used in an analytical model developed to study how rotor flow and blade parameters and turbulence properties such as energy, velocity correlations, and length scale affect the rotor wake characteristics and its diffusion properties. The model, includes three dimensional attributes, can be used in predicting the discrete as well as broadband noise generated in a fan rotor, as well as in evaluating the aerodynamic losses, efficiency and optimum spacing between a rotor and stator in turbomachinery.

Reynolds, B.↗

NASA NTRS1977

Rationale for selection of a flight control system for lift cruise fan V/STOL aircraft

Various features of the lift cruise fan V/STOL concept are briefly reviewed. The ability to operate from small ships in adverse weather, low visibility, and rough sea conditions is emphasized as is the need for a highly capable, flexible, and reliabile flight control system. A three channel control by wire, digital flight control system is suggested. The requirement for automatic flight control, the advantage of control by wire implementation, the preference for a digital computer, and the need for three channel redundancy are among the factors discussed.

Konsewicz, R. K.↗

NASA NTRS1977

Preliminary design of a flight control system for a V/STOL airplane with geared variable pitch fans

A flight control system designed for an aircraft powered by three variable pitch fans, interconnected by shafts to provide lifting system redundancy is considered for application to a Navy Type A V/STOL aircraft with similar configurational features. The differences and similarities in the applications are discussed with emphasis on a design approach for safety in the event of failures in the propulsion and flight control systems. Differences in flying qualities and system design criteria are considered.

Gotleib, P.↗

NASA NTRS1975

Use of leaning vanes in a two stage fan

The use of leaning vanes for tone noise reduction was examined in terms of their application in a typical two-stage high pressure ratio fan. In particular for stages designed with outlet guide vanes and zero swirl between stages, leaning the vanes of the first stage stator was studied, since increasing the number of vanes and the gap between stages do not provide the desired advantage. It was shown that noise reduction at higher harmonics of blade passing frequency can be obtained by leaning the vanes.

Rao, G. V. R.↗

NASA NTRS1978

Impact behavior of filament wound graphite/epoxy fan blades

The fabrication and impact tests of graphite/epoxy filament wound fan blades are discussed. Blades which were spin tested at tip speeds up to 305 meters per second retained their structural integrity. Two blades were each impacted with a 454 gram slice of a 908 gram simulated bird at a tip speed of 263 meters per second and impact angles of 22 and 32 deg. The impact tests were recorded with high-speed movie film. The blade which was impacted at 22 deg sustained some root delamination but remained intact. The 32 deg impact separated the blade from the root. No local damage other than leading edge debonding was observed for either blade. Results of a failure mode analysis are also discussed.

Bowles, K. J.↗

NASA NTRS1978

Design of impact-resistant boron/aluminum large fan blade

The technical program was comprised of two technical tasks. Task 1 encompassed the preliminary boron/aluminum fan blade design effort. Two preliminary designs were evolved. An initial design consisted of 32 blades per stage and was based on material properties extracted from manufactured blades. A final design of 36 blades per stage was based on rule-of-mixture material properties. In Task 2, the selected preliminary blade design was refined via more sophisticated analytical tools. Detailed finite element stress analysis and aero performance analysis were carried out to determine blade material frequencies and directional stresses.

Salemme, C. T.↗

NASA NTRS1978

Measurements of inlet flow distortions in an axial flow fan (6 and 9 blade rotor)

A large quantity of experimental data on inlet flow distortions in an axial flow fan were obtained. The purpose of the study was to determine the effects of design and operating variables and the type of distortion on the response of an axial flow turbomachinery rotor. Included are background information and overall trends observed in distortion attenuation and unsteady total pressure losses.

Barr, L. C.↗

NASA NTRS1979

Effects of inflow distortion profiles on fan tone noise calculated using a 3-D theory

Calculations of the fan tone acoustic power and modal structure generated by complex distortions in axial inflow velocity are presented. The model used treats the motor as a rotating three-dimensional cascade and calculates the acoustic field from the distortion-produced dipole distribution on the blades including noncompact source effects. Radial and circumferential distortion shapes are synthesized from Fourier-Bessel components representing individual distortion modes. The relation between individual distortion modes and the generated acoustic modes is examined for particular distortion cases. Comparisons between theoretical and experimental results for distortions produced by wakes from upstream radial rods show that the analysis is a good predictor of acoustic power dependence on disturbance strength.

Kobayashi, H.↗