Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLEXURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

NASA ACTS Multibeam Antenna (MBA) System

The design of the Advanced Communications Technology Satellite MBA system, which provides both spot beam and scanning beam coverage to both high and low burst rates data-users is examined. The MBA consists of receive and transmit antennas installed on a common precision mounting platform that is integrated to the bus through three flexures; a lightweight system with low thermal distortion is obtained by using composite materials for the MBA structures. The RF design, which is a Cassegrain reflector with a large equivalent focal length/aperture size, is described. Consideration is given to the position of the feed in order to minimize scan loss and sidelobe levels, the size of the subreflector in order to minimize feed spillover, and antenna performance degradation caused by reflector surface distortion. Breadbroad model test result reveal that the maximum sidelobe level outside the 2.5 HPBW region is -30 dB or lower relative to the power.

Choung, Youn H.↗
NASA NTRS1987

Implications of lithospheric bending and faulting in lunar mare-terra tectonics

A qualitative model of lithospheric flexure and faulting is proposed which accounts for certain rille fault features around mare regions of the moon. It is suggested that the subsidence of lunar mare basins may be due to the existence of their mascons and their volcanic fills as loads that flexed the lithosphere, in addition to the effects of drying up and cooling of internal hot volumes. Differences in the internal attack against the lunar crust from above and below the mean surface are considered. The rille formation is shown to be characterized by peripheral bulging and bending, and it is suggested that asthenosphere-related effects in lunar tectonics may have been very important.

Raitala, Jouko↗
NASA NTRS1987

Durability characterization of ceramic materials for gas turbines

The strength retention of ceramic materials during extended high-temperature cyclic exposure is critical to their widespread application in gas turbine engines. During a continuing NASA funded program initated in 1979, reaction bonded silicon nitride (RBSN), sintered silicon carbide (SSC), reaction sintered silicon carbide (RSSC), and sintered silicon nitride (SSN) materials were evaluated following simulated gas turbine engine exposures. Exposures were performed by cycling specimens five times per hour between a high velocity burner discharge and a rapid air quench. The retained flexural strengths were determined following up to 3500 hours of exposure at temperatures up to 1370 C. Post-exposure strengths have been correlated with fractography and surface examination using SEM. Results illustrate excellent strength retention of SSC materials after 3500 hours of exposure to 1370 C. At 1200 C, RBSN and RSSC also demonstrate significant strength retention. Although SSN materials typically suffer significant strength losses during exposures at 1200 C, a new composition, which has improved high-temperature strength, also shows improved durability. In the majority of the materials, strength loss is typically associated with flaw formation in the protective SiO2 layer.

Carruthers, W. D.↗
NASA NTRS1987

Fracture of flash oxidized, yttria-doped sintered reaction-bonded silicon nitride

The oxidation behavior of a slip cast, yttria-doped, sintered reaction-bonded silicon nitride after 'flash oxidation' was investigated. It was found that both the static oxidation resistance and flexural stress rupture life (creep deformation) were improved at 1000 C in air compared to those of the same material without flash oxidation. Stress rupture data at high temperatures (1000 to 1200 C) are presented to indicate applied stress levels for oxidation-dependent and independent failures.

Govila, R. K.↗
NASA NTRS1987

Impact-induced fracture in a quasi-isotropic laminate

A systematic study of impact-induced fracture in a quasi-isotropic laminated composite is carried out. The main focus of the study is to understand damage initiation when a laminate is subjected to the impact of a foreign object. The total incipient damage of a laminate subjected to impact at higher than threshold velocity is also presented. The incipient damage is restricted to small growth from the initiation of the damage. The experimentally collected data are interpreted using a two-dimensional plane-strain finite-element analysis. The qualitative comparison suggests that the skew cracks in the proximal layers are primarily due to transverse shear stress. Skew cracks in the middle layers are also due to transverse shear stress. Vertical cracks in the distal layer are due to flexural stress transverse to the fiber orientation of the layer.

Joshi, S. P.↗
NASA NTRS1987

NDE reliability and process control for structural ceramics

The reliability of microfocus X-radiography and scanning laser acoustic microscopy for detecting microvoids in silicon nitride and silicon carbide was statistically evaluated. Materials- and process-related parameters that influenced the statistical findings in research samples are discussed. The use of conventional X-radiography in controlling and optimizing the processing and sintering of an Si3N4-SiO2-Y2O3 composition designated NASA 6Y is described. Radiographic evaluation and guidance helped develop uniform high-density Si3N4 modulus-of-rupture bars with improved four-point flexural strength (857, 544, and 462 MPa at room temperature, 1200 C, and 1370 C, respectively) and reduced strength scatter.

Baaklini, G. Y.↗
NASA NTRS1986

Slow crack growth in sintered silicon nitride

The strength and crack growth characteristics of a sintered silicon nitride were studied at 1000 C. Fractographic analysis of material failing in dynamic fatigue revealed the presence of slow crack growth (SCG) at stressing rates below 6 ksi/min. This material can sustain a 40-ksi flexural stress at 1000 C for 400 h or more but is susceptible to both SCG and creep deformation at higher stress levels. The crack velocity exponent (N) determined both from dynamic and static fatigue experiments lies in a range from 13 to 22. The subcritical crack growth and creep behavior at 1000 C is primarily controlled by the deformation of an intergranular glassy phase.

Khandelwal, P. K.↗
NASA NTRS1987

Mechanical and electrical properties of graphite fiber-epoxy composites made from pristine and bromine intercalated fibers

The mechanical and electrical properties of pristine and bromine intercalated graphite fiber-epoxy composites were compared. The two types of composite were similar in terms of tensile modulus, tensile strength, and Poisson's Ratio. However, the interlaminar shear strength of the brominated composite was 18 percent greater than its pristine counterpart. Only slight differences were observed in flexural properties. A five-fold decrease was observed in the electrical resistivity of the brominated composite parallel to the axis of the fibers, resulting in a unidirectional resistivity of about 90 microOmega/cm. Transverse resistivity was unaffected. Both types of composite were subjected to a simulated lightning strike of 10 KJ (at a peak current of 150 kA), and the composite with the intercalated graphite exhibited less damage.

Jaworske, Donald A.↗
NASA NTRS1987

Siloxane-modified polyethersulfideimide

BDSDA/APB, a novel linear polyethersulfideimide, was synthesized using siloxane units as flexible linkages in the backbone in an attempt to improve use properties and processability. The effect of these flexible linkages on molecular weight buildup, flexural strength and modulus, glass transition temperature, and melt-flow properties was determined.

Burks, Harold D.↗
NASA NTRS1988

Sizing Increases Fiber/Matrix Adhesion

Strengths of graphite fiber/polycarbonate matrix composites increased by precoating fibers with thin layer of polycarbonate. Flexural strengths of composite samples measured to determine effects of different fabrication conditions.

Cizmecioglu, Muzaffer↗
NASA NTRS1987

Flaw imaging and ultrasonic techniques for characterizing sintered silicon carbide

The capabilities were investigated of projection microfocus x-radiography, ultrasonic velocity and attenuation, and reflection scanning acoustic microscopy for characterizing silicon carbide specimens. Silicon carbide batches covered a range of densities and different microstructural characteristics. Room temperature, four point flexural strength tests were conducted. Fractography was used to identify types, sizes, and locations of fracture origins. Fracture toughness values were calculated from fracture strength and flaw characterization data. Detection capabilities of radiography and acoustic microscopy for fracture-causing flaws were evaluated. Applicability of ultrasonics for verifying material strength and toughness was examined.

Baaklini, George Y.↗
NASA NTRS1987

Development of an impact- and solvent-resistant thermoplastic composite matrix, phase 4

Polyimides from BTDA with m-phenylenediamine and three aliphatic diamines were prepared in cresol and characterized. Characterization tests included compression strength and modulus, stressed solvent resistance, and melt-flow tests. Efforts to reduce the molecular weights of these polymers by either stoichiometric imbalance or phthalic anhydride end capping produced opacity in the polymer moldings when the stoichiometry was less than 99 percent. Use of 2,4-diaminotoluene in place of the m-phenylenediamine allowed clear polymer moldings to be obtained at all stoichiometries by end capping or stoichiometric imbalance. After melt-flow/molecular-weight studies, carbon fabric composites were prepared from three polyimide compositions containing BTDA, 2,4-diaminotoluene and two aliphatic diamines. Flexural strengths of two of the resins were in excess of 689 MPa (100 ksi) at both room temperature and 93 C. The polyimide from BTDA was selected for scale-up and neat resin characterization tests. The Tg of this polymer was 233 C.

Delano, C. B.↗
NASA NTRS1987

An engineering study of hybrid adaptation of wind tunnel walls for three-dimensional testing

Solid wall tunnels having only upper and lower walls flexing are described. An algorithm for selecting the wall contours for both 2 and 3 dimensional wall flexure is presented and numerical experiments are used to validate its applicability to the general test case of 3 dimensional lifting aircraft models in rectangular cross section wind tunnels. The method requires an initial approximate representation of the model flow field at a given lift with wallls absent. The numerical methods utilized are derived by use of Green's source solutions obtained using the method of images; first order linearized flow theory is employed with Prandtl-Glauert compressibility transformations. Equations are derived for the flexed shape of a simple constant thickness plate wall under the influence of a finite number of jacks in an axial row along the plate centerline. The Green's source methods are developed to provide estimations of residual flow distortion (interferences) with measured wall pressures and wall flow inclinations as inputs.

Brown, Clinton↗
NASA NTRS1988

Correlations of norbornenyl crosslinked polyimide resin structures with resin thermo-oxidative stability, resin glass transition temperature and composite initial mechanical properties

PMR (polymerization of monomeric reactants) methodology was used to prepare 70 different polyimide oligomeric resins and 30 different unidirectional graphite fiber/polyimide composites. Monomeric composition as well as chain length between sites of crosslinks were varied to examine their effects on resin thermo-oxidative stability and glass transition temperature (Tg) of the cured/postcured resins. A linear correlation of decreasing 316 C resin weight loss/surface area versus (1) decreasing aliphatic content, or (2) increasing benzylic/aliphatic content stoichiometry ratio over a wide range of resin compositions was observed. An almost linear correlation of Tg versus molecular distance between the crosslinks was also observed. An attempt was made to correlate Tg with initial composite mechanical properties (flexural strength and interlaminar shear strength). However, the scatter in mechanical strength data prevented obtaining a clear correlation. Instead, only a range of composite mechanical properties was obtained at 25, 288, and 316 C. Perhaps more importantly, what did become apparent during the correlation study was (1) the PMR methodology could be used to prepare composites from resins containing a wide variety of monomer modifications, (2) that these composites almost invariably provided satisfactory initial mechanical properties as long as the resins formulated exhibited satisfactory processing flow, and (3) that PMR resins exhibited predictable rates of 316 C weight loss/surface area based on their benzylic/aliphatic stoichiometery ratio.

Alston, William B.↗
NASA NTRS1986

Ethynylated aromatics as high temperature matrix resins

Difunctional and trifunctional arylacetylenes were used as monomers to form thermoset matrix resin composites. Composites can be hot pressed at 180 C to react 80 percent of the acetylene groups. Crosslinking is completed by postcuring at 350 C. The postcured resins are thermally stable to nominally 460 C in air. As a result of their high crosslink density, the matrix exhibits brittle failure when unaxial composites are tested in tension. Failure of both uniaxial tensile and flexural specimens occurs in shear at the fiber matrix interface. Tensile fracture stresses for 0 deg composites fabricated with 60 v/o Celion 6K graphite fiber were 827 MPa. The strain to failure was 0.5 percent. Composites fabricated with 8 harness satin Celion cloth (Fiberite 1133) and tested in tension also failed in shear at tensile stresses of 413 MPa.

Hurwitz, Frances I.↗
NASA NTRS1987

Use of reinforced inorganic cement materials for spark wire and drift chamber wire frames

The results of a survey, materials test, and analysis study directed toward the development of an inorganic glass-fiber reinforced cement material for use in the construction of space qualified spark wire frames and drift chamber frames are presented. The purpose for this research was to evaluate the feasibility of using glass fiber reinforced cement (GFRC) for large dimensioned structural frames for supporting a number of precisely located spark wires in multiple planes. A survey of the current state of the art in fiber reinforced cement materials was made; material sample mixes were made and tested to determine their laboratory performances. Tests conducted on sample materials showed that compressive and flexural strengths of this material could approach values which would enable fabrication of structural spark wire frames.

Source record↗
NASA NTRS1988

Multi-hundred kilowatt roll ring assembly evaluation results

NASA Lewis Research Center has been evaluating low loss multi-hundred-kilowatt Roll Ring assemblies (an 8 circuit and a 4 circuit) for use on Space Station as the rotating joint power transfer device. In this device ac or dc power is transferred across the rotating joint through compressed rotating flexures. Results and conclusions of the evaluation program are presented.

Renz, David D.↗