SEARCH · Engineering Papers

Results for “EARTH SHAPE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

All sources NASA NTRS DOE OSTI

NASA NTRS2010

Orion Entry Performance-Based Center-of-Gravity Box

The Orion capsule is designed both for Low Earth Orbit missions to the ISS and for missions to the moon. For ISS class missions, the capsule will use an Apollo-style direct entry. For lunar return missions, depending on the timing of the mission, the capsule could perform a direct entry or a skip entry of up to 4800 n.mi. in order to land in the coastal waters of California. The physics of atmospheric re-entry determine the capability of the Orion vehicle. For a given vehicle mass and shape, physics tells us that the driving parameters for an entry vehicle are the hypersonic lift-to-drag ratio (L/D) and the flight path angle at entry interface (gamma(sub EI)). The design of the Orion atmospheric re-entry must meet constraints during both nominal and dispersed flight conditions on landing accuracy, heating rate, total heat load, sensed acceleration, and proper disposal of the Service Module. These constraints define an entry corridor in the space of L/D-gamma(sub EI); if the vehicle falls within this corridor, then all constraints are met. The gamma(sub EI) dimension of the corridor can be further constrained by the gloads experienced during emergency entries. Thus, the entry performance for the Orion vehicle can be described completely by the L/D. Bounds on the hypersonic L/D necessary to achieve all the mission requirements can be defined for the given entry corridor. Landing accuracy performance drives the lower limit on L/D. In order to achieve the desired landing accuracy, a minimum L/D must be ensured. The design of the Thermal Protection System (TPS) drives the upper limit on L/D. A higher L/D can drive mass into the design of the TPS. Conversely, once the TPS is designed, the L/D must be ensured to stay below a certain limit in order for the TPS to stay within its design envelop. The L/D must stay within its upper and lower bounds during dispersed flight conditions. L/D is a function of both the aerodynamics and the center-of-gravity (CG) of the vehicle. The aerodynamics of the vehicle are determined by Computational Fluid Mechanics (CFD) and wind tunnel tests. However, the aerodynamics are not known precisely. Instead, an aerodynamic database has been developed where the aerodynamic coefficients are known to fall within a probabilistic band defined by upper and lower bounds. It is expected that the probabilistic band will shrink after the first missions are flown and real-world data is collected. Until that time, the Orion must be designed to the current aerodynamic database. Thus, for a given aerodynamic database with given uncertainties, the allowable range in L/D can be mapped to an allowable box for the CG location. The CG box is used to set requirements on the dispersions allowed for vehicle packaging and cargo storage. As the aerodynamic uncertainties decrease, the size of the CG box can increase. This paper discusses the technique used to map the minimum and maximum L/D bounds set by the entry performance requirements to the allowable dispersions in CG while accounting for aerodynamic uncertainties. The L/D is defined as the ratio of the lift force to the drag force. It is equivalent to the ratio of lift coefficient (C(sub L)) over drag coefficient (C(sub D)). C(sub L) and C(sub D) are functions of Mach number (M) and angle of attack (alpha). A Mach number of 25 is used as a measuring point of the hypersonic L/D. Variations in C(sub L), C(sub D) and alpha cause variations in L/D. Equation (1) shows the three contributions to the variation in L/D.

Rea, Jeremy R.↗

NASA NTRS2021

Optial Experiments and Model Validation of Perturbed Starshade Designs

Starshades are a leading technology to enable the direct detection and spectroscopic characterization of Earth- like exoplanets. Critical starshade technologies are currently being advanced through the S5 Project and at the Princeton starshade testbed. We report on the status of Milestone 2 of the S5 Project, optical model validation. We present results from optical experiments of starshades with intentional perturbations built into their design. These perturbations are representative of the type of perturbations possible in a flight design and serve as points of validation for dffraction models and error budgets. We show experimental results for two perturbed shapes, a mask with all petals shifted radially outward by 5 um and a mask with shallow sine waves built into two petals. We compare these data to outputs of the optical model and demonstrate better than 25% agreement. We also present images taken in crossed polarized light and use those data to constrain physical parameters of the optical edge. Bringing in previously obtained results for other perturbed shapes, we show an agreement between experiment and model of better than 25% and argue that this satisfies the Milestone 2 criteria.

Galvin, Michael↗

NASA NTRSDate not supplied

Solar Sail Torque Model Characterization for the Near Earth Asteroid Scout Mission

Near Earth Asteroid Scout (NEA Scout) was a mission to test solar sail propulsion for orbital transfer from cislunar space to flyby and image an asteroid. One of the goals of the mission was to characterize the solar torque on the sail to ensure successful attitude control for the orbit transfer and imaging the asteroid. The simulation used to develop the flight attitude control software uses the generalized model for solar sails, a tensor equation of the forces and torques on sails of arbitrary shape. Rios-Reyes and Scheeres developed a general process to update the torque tensor coefficients using estimates of sail torque over a range of directions to the sun. Their process was adapted and implemented for the specific case of NEA Scout using spacecraft telemetry collected during sail characterization maneuvers in combination with simulation models and parameters. The NEA Scout maneuvers were limited to the operating range of the mission and constraints of the control hardware and allowed safe testing of each attitude before proceeding to the next. The NEA Scout reaction wheel speeds are used to measure accumulated momentum, while the Active Mass Translator (AMT) position is used to subtract out the torque from the center of mass crossed with the sail force and isolate the torque from only the sail shape. The process was tested by running attitude control simulations of the characterization maneuvers, generating simulated telemetry, estimating the solar torques, then using a least squares estimating the solar torque coefficients using least-squares and then performing a least-squares fit to the solar torque tensor coefficients. These estimated coefficients were tested by evaluating the solar torques under the same conditions as the simulated telemetry and comparing to the true simulated torques. Solar force model updates can be performed separately by observing the effect of the sail on the trajectory, and the torque model can be refined using those solar force updates. This process met the needs of the NEA Scout mission and can be adapted to characterize the solar torque for other missions with different sails.

solar sail↗

NASA NTRS1987

Intershock observations during STIP intervals 17 and 18

The Prognoz-10/Intercosmos satellite (Intershock Project) carried out observations from Earth orbit from 26 April 1985 until 11 November 1985, covering STIP Intervals XVII and XVIII. Data obtained during the systematic measurements in the course of STIP Interval XVII and part of XVIII are presented; i.e., hourly averages of the solar wind velocity, temperature and ion concentration, ion flux changes (10 to the -1 to 10 to the -3 Hz), plasma wave parameters, energetic particles flux, magnetic fields, etc. Special attention is paid to solar wind distrubances causing abrupt and large effects on the shape of the bow shock (i.e., on 2 May 1985 and 14 September 1985). Generally, the observation period was very close to a minimum of solar activity and was quiet without significant interplanetary shocks.

Zastenker, G.↗

NASA NTRS1991

Radar studies in the solar system

We are actively engaged in observations of asteroids and comets, both as planned targets and as targets of opportunity. The most recent example of the latter is asteroid 1991 AQ, which was discovered optically on January 14, 1991 and found to be rapidly nearing Earth. Due in part to our previous success in obtaining useful radar data on short notice, we were able to schedule time on the Arecibo radar on January 28-31, when the asteroid was within the Arecibo declination window. Each day during the period, a fresh ephemeris was made including all available data, both optical and radar. With further processing, the results of the observations are expected to include detailed two-dimensional images of the asteroid and information on its surface properties, size, shape and spin. The observing program also included two other asteroids, two of the four Galilean satellites of Jupiter, the satellites of Mars, and the planet Mercury. Analysis of newly available radar observations of Venus has led to a refinement of the spin vector of that planet and has thereby provided a coordinate basis for the Magellan spacecraft mapping mission.

Shapiro, Irwin I.↗

NASA NTRS2004

A Bootstrap Approach to Martian Manufacturing

In-Situ Resource Utilization (ISRU) is an essential element of any affordable strategy for a sustained human presence on Mars. Ideally, Martian habitats would be extremely massive to allow plenty of room to comfortably live and work, as well as to protect the occupants from the environment. Moreover, transportation and power generation systems would also require significant mass if affordable. For our approach to ISRU, we use the industrialization of the U.S. as a metaphor. The 19th century started with small blacksmith shops and ended with massive steel mills primarily accomplished by blacksmiths increasing their production capacity and product size to create larger shops, which produced small mills, which produced the large steel mills that industrialized the country. Most of the mass of a steel mill is comprised of steel in simple shapes, which are produced and repaired with few pieces of equipment also mostly made of steel in basic shapes. Due to this simplicity, we expect that the 19th century manufacturing growth can be repeated on Mars in the 21st century using robots as the primary labor force. We suggest a "bootstrap" approach to manufacturing on Mars that uses a "seed" manufacturing system that uses regolith to create major structural components and spare parts. The regolith would be melted, foamed, and sintered as needed to fabricate parts using casting and solid freeform fabrication techniques. Complex components, such as electronics, would be brought from Earth and integrated as needed. These parts would be assembled to create additional manufacturing systems, which can be both more capable and higher capacity. These subsequent manufacturing systems could refine vast amounts of raw materials to create large components, as well as assemble equipment, habitats, pressure vessels, cranes, pipelines, railways, trains, power generation stations, and other facilities needed to economically maintain a sustained human presence on Mars.

Dorais, Gregory A.↗

NASA NTRS2013

Evidence for Two Separate Heliospheric Current Sheets of Cylindrical Shape During Mid-2012

During the reversal of the Sun's polar fields at sunspot maximum, outward extrapolations of magnetograph measurements often predict the presence of two or more current sheets extending into the interplanetary medium, instead of the single heliospheric current sheet (HCS) that forms the basis of the standard 'ballerina skirt' picture. By comparing potential-field source-surface models of the coronal streamer belt with white-light coronagraph observations, we deduce that the HCS was split into two distinct structures with circular cross sections during mid-2012. These cylindrical current sheets were centered near the heliographic equator and separated in longitude by roughly 180 deg; a corresponding four-sector polarity pattern was observed at Earth. Each cylinder enclosed a negative-polarity coronal hole that was identifiable in extreme ultraviolet images and gave rise to a high-speed stream. The two current sheet systems are shown to be a result of the dominance of the Sun's nonaxisymmetric quadrupole component, as the axial dipole field was undergoing its reversal during solar cycle 24.

CORONA↗

NASA NTRSDate not supplied

Solar Sail Torque Model Characterization for the Near Earth Asteroid Scout Mission

Near Earth Asteroid Scout (NEA Scout) was a mission to test solar sail propulsion for orbital transfer from cislunar space to flyby and image an asteroid. Had it succeeded, one of the mission goals was to characterize the solar torque on the sail to ensure successful attitude control for the orbit transfer and imaging the asteroid. The simulation used to develop the flight attitude control software uses the generalized model for solar sails, a tensor equation of the forces and torques on sails of arbitrary shape. Rios-Reyes and Scheeres developed a general process to update the torque tensor coefficients using estimates of sail torque over a range of directions to the sun. Their process was adapted and implemented for the specific case of NEA Scout using spacecraft telemetry collected during sail characterization maneuvers in combination with simulation models and parameters. The NEA Scout maneuvers were limited to the operating range of the mission and constraints of the control hardware and allowed safe testing of each attitude before proceeding to the next. The NEA Scout reaction wheel speeds are used to measure accumulated momentum, while the Active Mass Translator (AMT) position is used to subtract out the torque from the center of mass crossed with the sail force and isolate the torque from only the sail shape. The process was tested by running attitude control simulations of the characterization maneuvers, generating simulated telemetry, estimating the solar torques, then using a least squares estimating the solar torque coefficients using least-squares and then performing a least-squares fit to the solar torque tensor coefficients. These estimated coefficients were tested by evaluating the solar torques under the same conditions as the simulated telemetry and comparing to the true simulated torques. Solar force model updates can be performed separately by observing the effect of the sail on the trajectory, and the torque model can be refined using those solar force updates. This process met the needs of the NEA Scout mission and can be adapted to characterize the solar torque for other missions with different sails.

solar sail↗

NASA NTRS1973

Time variations of magnetospheric intensities of outer zone protons, alpha particles and ions (Z greater than or equal to 2)

A comprehensive study of the temporal behavior of trapped protons, alpha particles and ions (Z 2) in outer zone of the earth's magnetosphere has been made. These observations were made by the Injun V satellite during the first 21 months of operation, August 1968 to May 1970. Rapid increases in the observed number of particles followed by slower exponential decay characterize the data. Comparisons are made with the temporal behavior of interplanetary particles of the same energy observed by Explorer 35. Increases in the trapped fluxes generally correspond to enhanced interplanetary activity. The energy spectra of protons and alpha particles at L = 3 have similar shapes when compared on an energy per charge basis while the respective polar cap spectra have similar shape on an energy per nucleon basis. Apparent inward trans-L motion of energetic protons is observed. These particles are diffused inward by a process involving fluctuating electric fields. The loss of trapped low altitude protons, alpha particles and ions (Z 2) is controlled by coulombic energy loss in the atmosphere.

Randall, B. A.↗

NASA NTRS2016

Demonstration of Nautilus Centripetal Capillary Condenser Technology

This paper describes the results of a proof of concept effort for development of a Nautilus Centripetal Capillary Condenser (NCCC or NC3) used for microgravity compatible water recovery from moist air with integral passive phase separation. Removal of liquid condensate from the air stream exiting a condenser is readily performed here on Earth. In order to perform this function in space however, without gravity or mechanical action, other tactics including utilization of inertial, drag and capillary forces are required. Within the NC3, liquid water forms via condensation on cold condenser surfaces as humid air passes along multiple spiral channels, each in its own plane, all together forming a stacked plate assembly. Non-mechanical inertial forces are employed to transfer condensate, as it forms, via centripetal action to the outer perimeter of each channel. A V-shaped groove, constructed on this outer edge of the spiral channel, increases local capillary forces thereby retaining the liquid. Air drag then pulls the liquid along to a collection region near the center of the device. Dry air produced by each parallel spiral channel is combined in a common orthogonal, out-of-plane conduit passing down the axial center of the stacked device. Similarly, the parallel condensate streams are combined and removed from the condenser/separator through yet another out-of-plane axial conduit. NC3 is an integration of conventional finned condenser operation, combined with static phase separation and capillary transport phenomena. A Mars' transit mission would be a logical application for this technology where gravity is absent and the use of vibrating, energy-intensive, motor-driven centrifugal separators is undesired. Here a vapor stream from either the Heat Melt Compactor or the Carbon dioxide Reduction Assembly, for example, would be dried to a dew point of 10 deg using a passive NC3 condenser/separator with the precious water condensate recycled to the water bus.

Separator↗

NASA NTRS1995

Nature and location of the source of plasma sheet boundary layer ion beams

Onsager et al. (1991) have put forward a model of the formation of the plasma sheet boundary layer (PSBL) which relies on a steady source of plasma from a spatially extended plasma sheet, together with steady equatorward and earthward ExB convection of field lines due to reconnection at a downtail neutral line. This model is a synthesis of earlier proposals and it explains such features as an electron layer exterior to the ion boundary layer, ion velocity dispersion, counter streaming beams, low-speed cutoffs in the beams. It also explains the apparent evolution of the ion beams through 'kidney bean' shaped velocity-space distributions toward quasi-isotropic shells without invoking pitch angle scattering or energy diffusion. In this paper we explore two ramifications of the model. In principle we can map, as a function of time, the downtail neutral line distance and establish whether or not it is retreating during substorm recovery. We can also reconstruct the plasma distribution function near the neutral line to see if it is most consistent with mantle or plasma sheet plasma. We perform this analysis using International Sun Earth Explorer (ISEE) Fast Plasma Experiment (FPE) data for two plasma sheet recovery events, one on March 1, 1978, and the other on April 18, 1978. On March 1, 1978, we find evidence for an initial retreat from around 110 to 160 R(sub E) in the first 15 min; little further retreat occurs thereafter. On April 18, 1978, the neutral line location ranges from as little as 40 R(sub E) tailward of the satellite to as much as 200 R(sub E), but there is no evidence for a systematic retreat. The reconstructed ion distributions for these events are most consistent with a plasma sheet origin for the March 1 case and possibly plasma mantle or low-latitude boundary layer for the April 18 case.

Elphic, R. C.↗

NASA NTRS1960

An Approximate Analytical Method for Studying Atmosphere Entry of Vehicles with Modulated Aerodynamic Forces

The dimensionless, transformed, nonlinear differential equation developed in NASA TR R-11 for describing the approximate motion and heating during entry into planetary atmospheres for constant aerodynamic coefficients and vehicle shape has been modified to include entries during which the aerodynamic coefficients and the vehicle shape are varied. The generality of the application of the original equation to vehicles of arbitrary weight, size, and shape and to arbitrary atmospheres is retained. A closed-form solution for the motion, heating, and the variation of drag loading parameter m/C(D)A has been obtained for the case of constant maximum resultant deceleration during nonlifting entries. This solution requires certain simplifying assumptions which do not compromise the accuracy of the results. The closed-form solution has been used to determine the variation of m/C(D)A required to reduce peak decelerations and to broaden the corridor for nonlifting entry into the earth's atmosphere at escape velocity. The attendant heating penalty is also studied.

Levy, Lionel L., Jr.↗

NASA NTRS2000

X-38 Experimental Aerothermodynamics

The X-38 program seeks to demonstrate an autonomously returned orbital test flight vehicle to support the development of an operational Crew Return Vehicle for the International Space Station. The test flight, anticipated in 2002, is intended to demonstrate the entire mission profile of returning Space Station crew members safely back to earth in the event of medical or mechanical emergency. Integral to the formulation of the X-38 flight data book and the design of the thermal protection system, the aerothermodynamic environment is being defined through a synergistic combination of ground based testing and computational fluid dynamics. This report provides an overview of the hypersonic aerothermodynamic wind tunnel program conducted at the NASA Langley Research Center in support of the X-38 development. Global and discrete surface heat transfer force and moment, surface streamline patterns, and shock shapes were measured on scaled models of the proposed X-38 configuration in different test gases at Mach 6, 10 and 20. The test parametrics include angle of attack from 0 to 50 degs, unit Reynolds numbers from 0.3 x 10 (exp 6) to 16 x 10 (exp 6)/ ft, rudder deflections of 0, 2, and 5 deg. and body flap deflections from 0 to 30 deg. Results from hypersonic aerodynamic screening studies that were conducted as the configuration evolved to the present shape at, presented. Heavy gas simulation tests have indicated that the primary real gas effects on X-38 aerodynamics at trim conditions are expected to favorably influence flap effectiveness. Comparisons of the experimental heating and force and moment data to prediction and the current aerodynamic data book are highlighted. The effects of discrete roughness elements on boundary layer transition were investigated at Mach 6 and the development of a transition correlation for the X-38 vehicle is described. Extrapolation of ground based heating measurements to flight radiation equilibrium wall temperatures at Mach 6 and 10 were made and generally compared to within 50 deg F of flight prediction.

Horvath, Thomas J.↗

NASA NTRS2004

Spatially Complete Surface Albedo Data Sets: Value-Added Products Derived from Terra MODIS Land Products

Spectral land surface albedo is an important parameter for describing the radiative properties of the Earth. Accordingly it reflects the consequences of natural and human interactions, such as anthropogenic, meteorological, and phenological effects, on global and local climatological trends. Consequently, albedos are integral parts in a variety of research areas, such as general circulation models (GCMs), energy balance studies, modeling of land use and land use change, and biophysical, oceanographic, and meteorological studies. The availability of global albedo data over a large range of spectral channels and at high spatial resolution has dramatically improved with the launch of the Moderate Resolution Imaging Spectroradiometer (MODIS) instrument aboard NASA s Earth Observing System (EOS) Terra spacecraft in December 1999. However, lack of spatial and temporal coverage due to cloud and snow effects can preclude utilization of official products in production and research studies. We report on a technique used to fill incomplete MOD43 albedo data sets with the intention of providing complete value-added maps. The technique is influenced by the phenological concept that within a certain area, a pixel s ecosystem class should exhibit similar growth cycle events over the same time period. The shape of an area s phenological temporal curve can be imposed upon existing pixel-level data to fill missing temporal points. The methodology will be reviewed by showcasing 2001 global and regional results of complete albedo and NDVl data sets.

Moody, E. G.↗

NASA NTRS2024

FLUTE: Fluidic Telescope

The future of space-based UV/optical/IR astronomy requires ever larger telescopes. The highest priority astrophysics targets (including Earth-like exoplanets, first generation stars, and early galaxies) are all extremely faint, which presents an ongoing challenge for current missions and is the opportunity space for next generation telescopes: larger telescopes are the primary way to address this issue. The FLUTE project aims to revolutionize space astronomy (and in-space manufacturing of high-precision optics for a variety of other applications) by leveraging the physics of wetting and hydrostatic phenomena in microgravity. The approach being developed by the team uses surface tension to shape a liquid into a desired optical form with sub-nanometer surface quality. A liquid with appropriate optical properties is brought into contact with a high affinity bounding frame, resulting in pinning of the liquid to the frame. In microgravity, the shape of the free surface is dictated solely by surface tension, thus assuming the shape of a spherical cap. Further dynamic control over the shape is possible through changing the liquid volume, the frame geometry, and — if desired — with the addition of external forces (e.g., electromagnetic forces). The approach is scale-invariant and is expected to enable space telescopes with optical apertures measuring in tens or even hundreds of meters, allowing, for instance, direct imaging of extra-solar planets. Both refractive and reflective optical components can be created using this approach. If the liquid’s properties enable solidification (e.g., a liquid metal), the resulting component can then become an optical-grade solid object, without post-processing steps. The approach has been successfully validated in a laboratory neutral buoyancy environment, in parabolic microgravity flights, and in experiments aboard the International Space Station (ISS). FLUTE is a collaboration between NASA Ames Research Center, NASA Goddard Space Flight Center, and Technion – Israel Institute of Technology. More on information on FLUTE can be found at https://www.nasa.gov/science-research/astrophysics/what-is-the-fluidic-telescope/. This presentation provides an update on the project's accomplishments to-date and discusses next steps.

Space observatory↗

NASA NTRS1976

Detailed gravimetric geoid computations in North America

A detailed gravimetric geoid has been computed for the Eastern United States and the Northwestern Atlantic Ocean by combining the Goddard Space Flight Center GEM-8 earth gravity model with the available 15 x 15 arcmin and 1 x 1 deg mean free air surface gravity observations. The short wavelength undulations were computed by applying Stokes' formula to the 15 x 15 arcmin and 1 x 1 deg surface data. The long wavelength undulations were provided by the GEM-8 model. The gravimetric geoid has been compared with Geoceiver derived and astrogeodetically determined geoid heights in the United States and the rms agreement is on the order of 1.5 meters. Excellent agreement in shape has been found between the detailed geoid and geoidal profiles derived from GEOS-III altimeter data in the Northwest Atlantic Ocean.

Marsh, J. G.↗

NASA NTRS1985

Satellite tour design for the Cassini mission

The mission design for the Cassini satellite tour of Saturn is described. The use of Titan encounters for gravity-assisted trajectory shaping to satisfy atmosphere, magnetosphere, and satellite science requirements is discussed. Three candidate satellite tours that illustrate the tradeoffs between different strategies to satisfy the science objectives are presented. Tour characteristics for a 4yr mission include at least 30 Titan encounters to provide a minimum of 90 deg orbit rotation for either a magnetotail petal orbit or noon petal orbit; evenly distributed Titan ground tracks for radar mapping coverage; at least 2 Iapetus and 1 Enceladus close flybys; inclined orbits during the first 3 yr to provide Earth and Sun occultations by Saturn and its rings; and Polar orbits during the fourth year.

Diehl, R. E.↗

NASA NTRS1991

Spatial sampling errors for a satellite-borne scanning radiometer

The Clouds and Earth's Radiant Energy System (CERES) scanning radiometer is planned as the Earth radiation budget instrument for the Earth Observation System, to be flown in the late 1990's. In order to minimize the spatial sampling errors of the measurements, it is necessary to select design parameters for the instrument such that the resulting point spread function will minimize spatial sampling errors. These errors are described as aliasing and blurring errors. Aliasing errors are due to presence in the measurements of spatial frequencies beyond the Nyquist frequency, and blurring errors are due to attenuation of frequencies below the Nyquist frequency. The design parameters include pixel shape and dimensions, sampling rate, scan period, and time constants of the measurements. For a satellite-borne scanning radiometer, the pixel footprint grows quickly at large nadir angles. The aliasing errors thus decrease with increasing scan angle, but the blurring errors grow quickly. The best design minimizes the sum of these two errors over a range of scan angles. Results of a parameter study are presented, showing effects of data rates, pixel dimensions, spacecraft altitude, and distance from the spacecraft track.

Manalo, Natividad D.↗