Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Charging Data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Battery peak charge voltage monitor for dual air density satellite

A battery peak charge voltage monitor was developed for use on the dual air density satellite (DADS). This device retains a reading of the maximum voltage reached by the spacecraft battery during periods of charging, and makes it available during periods of data transmission. The monitor is connected across the battery and operates solely from the battery; it is powered continuously with quiescent input current of only 3 milliamperes. Standard integrated circuits and a thin-film resistor network are utilized. The monitor occupies approximately 40 square centimeters of a printed-circuit board within a larger electronic package.

Shull, T. A.↗
NASA NTRS1975

Research investigation of the physical interactions and phenomena associated with hypervelocity sub-micron particles

Signals from impact ionization plasmas were studied as a means of performing microparticle composition analysis. Impact ionization signal response was measured in a time-of-flight (TOF) system for lanthanum hexaboride, carbonyl iron, and aluminum microparticle impacts on a tantalum target, primarily in the 1 - 8 km/s velocity range. Oscilloscope photographs of representative ion TOF signal response are given for each material studied. Graphs and histograms are presented of the total charge collected as well as the charge collected in each observed ion mass group. Data show that ion signals consist primarily of the lower ionization potential elements over the 1 - 8 km/s range.

Roy, N. L.↗
NASA NTRS1977

A comparison of photointerpretive and digital production methods for four key remote sensing-based information products

This paper evaluates the costs of producing four remote sensing-based information products: timber volume estimate tables, Level II land use/land cover maps, soil maps, and vegetative cover maps. Two production methods for each product are evaluated, one is based on digital processing of satellite data, and the other on conventional photointerpretation of aircraft data. For each product, a comparison is conducted of the two strategies' production costs (including data acquisition, 'ground truthing', interpretation, compilation, and printing charges) and their performance (as measured by accuracy and timeliness). Each of the production methods reviewed has been demonstrated - either operationally or experimentally - and the costs, timeliness and other performance estimates presented are based on observations made in practice. The results show that for these products, satellite-based production results in significant cost and timeliness improvements at the cost of a loss in accuracy.

Eastwood, L. F., Jr.↗
NASA NTRS1982

Secondary electron emission from a charged dielectric in the presence of normal and oblique electric fields

The secondary electron emission coefficient was obtained for a FEP-Teflon dielectric charged with monoenergetic electrons normally incident upon the surface of the specimen. Measurements of secondary emission coefficient were done for normal and oblique incidence with different primary beam energies in the presence of normal and oblique electric fields. A collimated probing beam was directed to different points on the surface of the specimen and the released or accumulated charge was monitored using an electrometer. The measured data for different probing beam energies, different impact points and different angles of incidence were plotted vs. impact energy and impact point. Data analyzed by computer simulations to find the potential distribution on the surface of the specimen and the electric field around it, is presented and discussed.

Javidi, B.↗
NASA NTRS1982

Effects of Titan on trapped particles in Saturn's magnetosphere

Magnetic field data from Voyager 1 magnetometer experiment are used with angular distribution data from the same spacecraft's low energy charged particle experiment to investigate the influences of Titan on the magnetosphere energetic particle distributions, with attention to the pitch angle distributions of ions and electrons. Titan appears to disrupt the corotation motion of the ions, since, while the fluxes of the ions in the corotation direction are of diminished intensity, those observed in the equatorial plane perpendicular to this direction are almost unaffected. The resulting distribution and trajectory modeling conclusions suggest that the convection electric field is absent in the wake of Titan, and that the presence of Titan produces a reduction in the fluxes of the electrons and flatter distributions with pitch angle.

Maclennan, C. G.↗
NASA NTRS1983

Laboratory and field observations related to ice particle and aircraft charging in convective storms

Graupel particle charging in simulated cloud conditions which show the need for the presence of ice crystals and cloud water simultaneously except under conditions where secondary ice crystal production occurs when charging initially occurs in the absence of ice crystals was examined. The magnitude of the charging increases with size of ice crystals, and impact velocity; it is also sensitive to impurities. The magnitude of the charge is also sensitive to temperature and the sign changes between -10 and -20 C, depending on cloud liquid water content. Aircraft studies were carried out in Montana convective clouds to test the validity of the extrapolation of the laboratory data to the atmosphere from the viewpoint of generation of charge, electric field, and aircraft charging during cloud penetration.

Christian, H.↗
NASA NTRS1982

Analysis of electromagnetic fields on an F-106B aircraft during lightning strikes

Information on the exterior electromagnetic environment of an aircraft when it is struck by lightning has been obtained during thunderstorm penetrations with an F-106B aircraft. Electric and magnetic fields were observed, using mainly time-derivative type sensors, with bandwidths to 50 MHz. Lightning pulse lengths ranging from 25 ns to 7 microsec have been recorded. Sufficient high-frequency content was present to excite electromagnetic resonances of the aircraft, and peaks in the frequency spectra of the waveforms in the range 7 to 23 MHz are in agreement with the resonant frequencies determined in laboratory scale-model tests. Both positively and negatively charged strikes were experienced, and most of the data suggest low values of peak current.

Trost, T. F.↗
NASA NTRS1983

Calibration of a stack of NaI scintillators at the Berkeley Bevalac

An analysis of the carbon and argon data reveals that essentially all of the charge-changing fragmentation reactions within the stack can be identified and removed by imposing the simple criteria relating the observed energy deposition profiles to the expected Bragg curve depositions. It is noted that these criteria are even capable of identifying approximately one-third of the expected neutron-stripping interactions, which in these cases have anomalous deposition profiles. The contribution of mass error from uncertainty in delta E has an upper limit of 0.25 percent for Mn; this produces an associated mass error for the experiment of about 0.14 amu. It is believed that this uncertainty will change little with changing gamma. Residual errors in the mapping produce even smaller mass errors for lighter isotopes, whereas photoelectron fluctuations and delta-ray effects are approximately the same independent of the charge and energy deposition.

Schindler, S. M.↗
NASA NTRS1985

Shuttle electrical environment

Part of an AFGL payload flown on the STS-4 mission consisted of experiments to measure in-situ electric fields, electron densities, and vehicle charging. During this flight some 11 hours of data were acquired ranging from 5 minute snapshots up to continuous half-orbits. These experiments are described and results presented for such vehicle induced events as a main engine burn, thruster firings and water dumps in addition to undisturbed periods. The main characteristic of all the vehicle induced events is shown to be an enhancement in the low frequency noise (less than 2 kHz), in both the electrostatic and electron irregularity (delta N/N) spectra. The non-event results indicate that the electrostatic broadband emissions show a white noise characteristic in the low frequency range up to 2 kHz at an amplitude of 10 db above the shuttle design specification limit, falling below that limit above 10 kHz. The vehicle potential remained within the range of -3 to +1 volt throughout the flight which exhibits normal behavior for a satellite in a low equatorial orbit.

Smiddy, M.↗
NASA NTRS1984

Titan's magnetospheric interaction

Voyager 1 encounter data are used to theoretically examine the interaction of Titan with the solar wind, the Saturn magnetosheath and the Saturn magnetosphere. The spacecraft data comprised magnetometer, plasma wave, radio signal and charged particle measurements. Attention is given to the Alfven (1.9) and Mach (0.57) numbers detected in the Saturn magnetosheath, along with a fast hydrodynamic Mach number of 0.55. Incident plasma interacted with the Titan atmosphere and produced a magnetosphere through mass capture and field-line draping. The tail region was loaded with N(+) and N2(+)/H2CN(+) ions instead of the strong H(+) signals typical of other regions. The magnetotail featured four lobes, and the Titan atmosphere was calculated to lose 10 to the 24th ions/sec. Finally, the Titan internal rotationally aligned magnetic field has an estimated strength of 7 x 10 to the 20th gauss/cu cm.

Neubauer, F. M.↗
NASA NTRS1986

Ground testing in a simulated auroral environment

Shuttle polar orbit missions are being planned in which astronaut extravehicular activities (EVA) will eventually include external operations or repair and refurbishment of satellites. Recent satellite data and model calculations show that significant spacecraft charging and differential charging occurs in that environment and could endanger equipment and personnel involved in the EVA. These spacecraft charging events take place in response to an intense flux of high energy electrons accompanied by a large drop in the ambient plasma density. The extent of which the auroral environment can be simulated in a large vacuum chamber are determined so that conditions which lead to significant charging and discharging may be observed and controlled. A large chamber would be required in order to simulate the effects of an aurora-like, large cross-section, energetic electron precipitation on a target system the size of an astronaut with a life support system. The precipitating electrons can be simulated with an array of multipactor sources and the background ionization produced by the beam can be limited to the range of the auroral density if the chamber pressure is not significantly above 1 x .000001 Torr. Some small chamber work has shown that the plasma in the beam will diffuse radially at a rate determined by the Bohm diffusion coefficient.

Mcintyre, Bernard↗
NASA NTRS1987

Analysis of relativistic nucleus-nucleus interactions in emulsion chambers

The development of a computer-assisted method is reported for the determination of the angular distribution data for secondary particles produced in relativistic nucleus-nucleus collisions in emulsions. The method is applied to emulsion detectors that were placed in a constant, uniform magnetic field and exposed to beams of 60 and 200 GeV/nucleon O-16 ions at the Super Proton Synchrotron (SPS) of the European Center for Nuclear Research (CERN). Linear regression analysis is used to determine the azimuthal and polar emission angles from measured track coordinate data. The software, written in BASIC, is designed to be machine independent, and adaptable to an automated system for acquiring the track coordinates. The fitting algorithm is deterministic, and takes into account the experimental uncertainty in the measured points. Further, a procedure for using the track data to estimate the linear momenta of the charged particles observed in the detectors is included.

Mcguire, Stephen C.↗
NASA NTRS1991

A charging study of the ACTS satellite using NASCAP

The results of a charging study conducted with the NASA Charging Analyzer Program (NASCAP) using a model of the Advanced Communications Technology Satellite (ACTS) are presented. The electrostatic discharge mechanisms are described including the field and potential threshold values that were monitored during the NASCAP simulation. Particular attention is given to the charging behavior of the ACTS inclined antennas. The data obtained indicate that the possibility of a discharge occurring in the immediate vicinity of the antennas is minimal when the semiconducting paint layer on the antenna's front surface has sufficient surface conductivity. It is shown that the metallized multilayer insulating blanket ACTS design provides good electrostatic discharge control.

Herr, Joel L.↗
NASA NTRS1997

Cosmic Ray Induced Degradation in X-Ray Detectors On Board the Near Earth Asteroid Rendezvous Spacecraft

The Near-Earth Asteroid Rendezvous (NEAR) mission is the first in NASA's new Discovery Program to explore the solar system. Launched in February 1996, the NEAR spacecraft will take a long cruise flight arriving at the asteroid 433 Eros in January 1999 for a one year orbiting survey operation. This long exposure to the space environment has already proven to be an additional complication for the x-ray spectrometer. The asteroid pointing detectors for the x-ray spectrometer are three gas-filled proportional counters with resolving power in the range of 1 keV. Therefore, to resolve the important but closely spaced magnesium, aluminum and silicon k alpha lines( 1.255, 1.487, 1.739 keV respectively), magnesium and aluminum balanced filters are used on two of the detectors. The x-ray florescence from the surface of Eros is stimulated by solar x-rays. A proportional counter and a silicon PIN detector are used to monitor the solar incident x-ray flux. The proportional counters are single wire gas filled beryllium lined steel tubes operating at about 1100 volt. The 25 cm(exp 2) optical window is one mil. thick beryllium. To define the detector's active region, two boron nitride disks were incorporated in the tube just outside window area. It appears from the space flight data that the space environment is creating a charge on these boron nitride disks which ultimately distorts the tube gain and resolution. This broadening of the photo peak makes it more difficult to identify weak peaks and so degrades the statistical accuracy for some very important elements such as sulfur, calcium and iron (2.307, 3.690, 6.403 keV respectively). If the broadening is severe enough in the low energy region, counts will be lost as the photo peak spreads below the lower level discriminator (0.7 keV).

Floyd, S. R.↗
NASA NTRS1999

Optical Analysis of Transparent Polymeric Material Exposed to Simulated Space Environment

Transparent polymeric materials are being designed and utilized as solar concentrating lenses for spacecraft power and propulsion systems. These polymeric lenses concentrate solar energy onto energy conversion devices such as solar cells and thermal energy systems. The conversion efficiency is directly related to the transmissivity of the polymeric lens. The Environmental Effects Group of the Marshall Space Flight Center's Materials, Processes, and Manufacturing Department exposed a variety of materials to a simulated space environment and evaluated them for an, change in optical transmission. These materials include Lexan(TM), polyethylene terephthalate (PET). several formulations of Tefzel(TM). and Teflon(TM), and silicone DC 93-500. Samples were exposed to a minimum of 1000 Equivalent Sun Hours (ESH) of near-UV radiation (250 - 400 nm wavelength). Data will be presented on materials exposed to charged particle radiation equivalent to a five-year dose in geosynchronous orbit. These exposures were performed in MSFC's Combined Environmental Effects Test Chamber, a unique facility with the capability to expose materials simultaneously or sequentially to protons, low-energy electrons, high-energy electrons, near UV radiation and vacuum UV radiation.Prolonged exposure to the space environment will decrease the polymer film's transmission and thus reduce the conversion efficiency. A method was developed to normalize the transmission loss and thus rank the materials according to their tolerance to space environmental exposure. Spectral results and the material ranking according to transmission loss are presented.

Edwards, David L.↗
NASA NTRS2006

Modeling and Correcting the Time-Dependent ACS PSF

The ability to accurately measure the shapes of faint objects in images taken with the Advanced Camera for Surveys (ACS) on the Hubble Space Telescope (HST) depends upon detailed knowledge of the Point Spread Function (PSF). We show that thermal fluctuations cause the PSF of the ACS Wide Field Camera (WFC) to vary over time. We describe a modified version of the TinyTim PSF modeling software to create artificial grids of stars across the ACS field of view at a range of telescope focus values. These models closely resemble the stars in real ACS images. Using 10 bright stars in a real image, we have been able to measure HST s apparent focus at the time of the exposure. TinyTim can then be used to model the PSF at any position on the ACS field of view. This obviates the need for images of dense stellar fields at different focus values, or interpolation between the few observed stars. We show that residual differences between our TinyTim models and real data are likely due to the effects of Charge Transfer Efficiency (CTE) degradation. Furthermore, we discuss stochastic noise that is added to the shape of point sources when distortion is removed, and we present MultiDrizzle parameters that are optimal for weak lensing science. Specifically, we find that reducing the MultiDrizzle output pixel scale and choosing a Gaussian kernel significantly stabilizes the resulting PSF after image combination, while still eliminating cosmic rays/bad pixels, and correcting the large geometric distortion in the ACS. We discuss future plans, which include more detailed study of the effects of CTE degradation on object shapes and releasing our TinyTim models to the astronomical community.

Rhodes, Jason↗
NASA NTRS2007

Electrodynamic Tether Operations beyond the Ionosphere in the Low-Density Magnetosphere

In the classical concept for the operation of electrodynamic tethers in space, a voltage is generated across the tether, either by the tether's orbital motion through the earth's planetary magnetic field or by a power supply; electrons are then collected from the ionospheric plasma at the positive pole; actively emitted back into space at the negative pole; and the circuit is closed by currents driven through the ambient conducting ionosphere. This concept has been proven to work in space by the Tethered Satellite System TSS-1 and TSS-1R Space Shuttle missions; and the Plasma Motor-Generator (PMG) tether flight experiment. However, it limits electrodynamic tether operations to the F-region of the ionosphere where the plasma density is sufficient to conduct the required currents--in other words, between altitudes of approximately 200 to 1000 km in sunlight. In the earth's shadow, the ionospheric density drops precipitously and tether operations, using the above approach, are not effective--even within this altitude range. There are numerous missions that require in-space propulsion in the Earth's shadow and/or outside of the above altitude range. This paper will, therefore, present the fundamentals of a concept that would allow electrodynamic tethers to operate almost anywhere within the magnetosphere, the region of space containing the earth's planetary magnetic field. In other words, because operations would be virtually independent of any ambient plasma, the range of electrodynamic operations would be extended into the earth's shadow and out to synchronous orbit--forty times the present operational range. The key to this concept is the active generation of plasma at each pole of the tether so that current generation ,does not depend on the conductivity of the ambient ionosphere. Arguments will be presented, based on ,existing flight data, which shed light on the behavior of charge emissions in space and show the plausibility of the concept.

Stone, Nobie H.↗
DOE OSTI2025

A Measurement of the Neutron Electromagnetic Form Factor Ratio from a Rosenbluth Technique with Simultaneous Detection of Neutrons and Protons

The internal structure of protons and neutrons provides insight into both the dynamical behavior of the constitute quarks and gluons, and emergent properties of the nucleons (such as mass, spin, and electromagnetic distributions). Elastic electron-nucleon scattering can probe the elastic electromagnetic form factors of the nucleon. The electric and magnetic form factors, respectively, encode information about the internal charge and magnetization distributions within the nucleon. Precision data for these form factors, over a broad range of the four-momentum transfer squared, Q^2, can benchmark theoretical models describing the strong interaction of nuclear physics. The Super BigBite Spectrometer (SBS) program in Hall A at Jefferson Lab, is a series of high-precision experiments which seek to significantly extend the Q^2 reach of previous data for the nucleon electromagnetic form factors. The first two experiments of this program are known as G_M^n and the neutron Two Photon Exchange (nTPE) and the data were collected from October 2021 to February 2022. Both experiments were conducted with the simultaneous measurement of D(e,e'n) and D(e,e'p) reactions for quasi-elastic electron-deuteron scattering. The scattered electrons were detected in the BigBite Spectrometer, which features multiple large-acceptance Gas Electron Multiplier (GEM) detectors. The Super BigBite Spectrometer provided simultaneous detection of scattered nucleons, and utilized a large acceptance dipole magnet and Hadron Calorimeter (HCal). The G_M^n experiment provides precision measurements of the neutron magnetic form factor, via the ratio method, over a Q^2 range of 3.0 to 13.5 (GeV/c)2. From this data analysis, preliminary values for G_M^n/µ_n G_D are extracted. For Q^2=4.48 (GeV/c)2 we find G_M^n/µ_n G_D=0.9546±0.0132 and for Q^2=4.476 (GeV/c)2 we find G_M^n/µ_n G_D=0.9563±0.0110. These preliminary G_M^n/µ_n G_D values are more precise than existing world data in this Q^2 regime and are consistent with the most recent parameterization of the G_M^n/µ_n G_D world data. The nTPE experiment provides a first measurement of the neutron Rosenbluth Slope and seeks to quantify the two-photon exchange(TPE) contribution to elastic electron-neutron scattering at a fixed Q^2=4.5 (GeV/c)2 with two different beam energies and scattering angle values. For data of the proton form factor ratio, µ_p G_E^p/G_M^p, significant discrepancies exist between values obtained from Rosenbluth Separation and polarization transfer measurement, particularly at large Q^2, and TPE contributions are thought to resolve this discrepancy. The impacts of TPE contributions have not yet been experimentally established for the neutron. From the data analysis presented in this dissertation, a preliminary result for the neutron Rosenbluth Slope is found as S^n=(G_E^n )^2/t_n (G_M^n )^2=0.0916±0.0476 for Q^2=4.48 (GeV/c)2. This value of the neutron Rosenbluth Slope is consistent with the world data extrapolation and the absence of large TPE corrections.

Wertz, Ezekiel [Thomas Jefferson National Accelera↗