Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BRITTLENESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

In situ self-ion (Fe + ) irradiation of ODS-FeCrAl alloy fuel cladding materials with different Cr contents: The early stages of Cr-rich α’ phase precipitation

Oxide-dispersion-strengthened FeCrAl (ODS-FeCrAl) alloys are candidate accident-tolerant fuel cladding materials for light water reactors because they demonstrate satisfactory resistance to materials degradation effects such as high-temperature oxidation, radiation-induced swelling, and creep. Their perspective deployment to market is challenged, however, by their inherent susceptibility to irradiation embrittlement caused by the precipitation of the brittle Cr-rich α’ phase at relatively low temperatures (≤475 °C). This work used in situ self-ion irradiation (150 keV Fe + ) in a transmission electron microscope to elucidate the early stages of Cr-rich α’ phase precipitation in three candidate ODS-FeCrAl alloy fuel cladding materials with different Cr contents (10, 12, and 20 wt.%) and microstructures. The early stages of the process resulting in the precipitation of the Cr-rich α’ phase in these three ODS-FeCrAl alloys under Fe + irradiation were investigated at room temperature and 300 °C up to total fluences of 1.7 × 10 15 ions·cm -2 (2 dpa) and 3.4 × 10 15 ions·cm -2 (4 dpa), using three damage dose rates (5 × 10 –5 , 3.3 × 10 –4 , and 2 × 10 –3 dpa·s -1 ). Post-irradiation examination via scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy and electron energy loss spectroscopy suggested that the precipitation of the Cr-rich α’ phase might be promoted by the phase separation of the alloy matrix into Cr-rich and Fe-rich regions. Interestingly, oxygen impurities segregated preferentially in the Cr-rich regions, possibly promoting the radiation-assisted formation of the Cr-rich α’ phase. α’ phase precipitation was more pronounced at room temperature when compared to 300 °C, and it was clearly promoted by the progressive increase in the Cr content of the ODS-FeCrAl alloy.

36 MATERIALS SCIENCE↗

Impact of post-irradiation annealing on mechanical performance of irradiated 718 alloy

Here, the effect of post-irradiation annealing on solution-annealed 718 alloy was investigated using advanced mechanical testing, fractography, scanning electron microscopy, and transmission electron microscopy. Specimens were extracted from a proton beam window operated at the Spallation Neutron Source, irradiated with 940 MeV protons to a maximum dose of approximately 9.7 displacements per atom (dpa) at a calculated temperature not exceeding 110 °C while in service. Helium and hydrogen concentrations reached about 1700 and 6900 atomic parts per million (appm), respectively. Despite irradiation and high tensile strength (yield stress over 1 GPa), the material exhibited significant ductility. Annealing at 500 °C, 700 °C, and 900 °C for 30 min resulted in an appreciable decrease in yield strength and an increase in ductility for annealing treatments at 500 °C and 900 °C relative to the strength and ductility of the as-irradiated material. The presence of helium and hydrogen led to cavity formation and cleavage-like brittle features on fractured surfaces; however, high-magnification imaging revealed the presence of small-scale ductile dimples, indicating that the fracture mechanism remained mixed. The annealed specimens retained total elongation levels of 14–33 %, and there was no sudden drop in ductility after heat treatments. The ductility level in the irradiated and annealed material is notable despite the presence of helium and hydrogen.

36 MATERIALS SCIENCE↗

Analysis of attenuation data from the decommissioned ZIon unit 1 reactor pressure vessel beltline weld

In order to examine the attenuation of radiation damage through the thickness of an irradiated reactor pressure vessel (RPV), four segments were acquired from the Zion Unit 1 power plant RPV after the plant was decommissioned. The Zion Unit 1 RPV Beltline Weld Segment 1 was cut into seven blocks, consisting of five base metal and two beltline welds from the high fluence region of the segment. Through-wall test specimens were machined and tested. Specimens included those used for Charpy impact, Master Curve fracture toughness testing, and chemical analysis. The observed through-thickness ductile-to-brittle transition temperatures in the beltline weld deviated significantly from the expected behavior based on the attenuation of fast fluence as a function of depth into the RPV. Beginning at the inside surface, the 41-J Charpy transition temperature was either flat or slightly increasing until the ¾ -T location. The results of a simple, model-based analysis of the Zion beltline weld material that included the irradiation conditions and material chemistry were generally consistent with industry trend curves and the standard attenuation model, rather than the observed data. Although there was no archive material from the RPV available to permit measurement of the unirradiated properties, fracture toughness specimens fabricated from archive surveillance weld were used to obtain an estimate of the initial through-thickness values of the Charpy transition temperature. The Charpy shifts obtained using this approach were similarly in disagreement with the predictions of the US NRC Regulatory Guide 1.99, Rev. 2. However, testing of irradiated Charpy specimens taken from the RPV following post-irradiation annealing (10 hr. at 500 °C) provided a quite different estimate of the unirradiated properties which improved the agreement between the inferred through-thickness Charpy shifts and exponential attenuation model included in Regulatory Guide 1.99/2. In conclusion, the analysis of the Zion data and data obtained in previous post-mortem examinations of decommissioned RPVs indicates that more work is needed to understand the through-thickness properties of RPV materials in order to properly assess through-wall damage attenuation.

Charpy impact↗

Evaluation of corrosion coupons exposed to molten-chloride electrorefiner salts long term

Corrosion mitigation has long been considered a challenge in long-term service of both pyrochemical reprocessing and molten salt reactor applications. Corrosion coupons consisting of 2.25Cr 1Mo ASME SA387 Grade 22 Class 2 steel, were installed in a uranium electrorefiner containing molten chloride salt at 500°C. This electrorefiner went into service at Idaho National Laboratory in 1994. Seven of these coupons were removed in 2019 (i.e., submerged in molten salt for 25 years) for analysis and characterization including neutron imaging, optical microscopy, scanning electron microscopy, and wave/energy dispersive x-ray spectroscopy. The results showed that all seven coupons experienced between 30 to 175 µm of surface degradation without evidence of brittle fracture. Meaning there was no evidence of accelerated corrosion or fractures, and the average steel surface loss was of less than 5 µm per year. All indications were that the environmental conditions inside the electrorefiner were favorable for the steel alloy.

36 - MATERIALS SCIENCE↗

Assessing the influence of processing parameters and external loading on the nanoporous structure and morphology of nanoporous gold toward catalytic applications

Nanoporous gold structure gains several unique physical and chemical properties from its nanoscale foam structure composed of ligaments and connected pores. The high specific surface area and interconnected pores make its structure ideal for gas catalysis. Catalytic activity arises in part from the high number density of surface steps and kinks at points of high curvature in the nanoporous structure. However, the structure also makes the material macroscopically brittle and unreliable for many applications due to poor mechanical stability. The ligament diameter, which regulates both desirable chemical properties and mechanical instability, can be tuned to over three orders of magnitude, but few morphology features can be adjusted independently of this. In this report we fabricate nanoporous gold with an average ligament diameter of around 10 nm while varying synthesis parameters and quantify the resulting morphology in order to evaluate the effect of processing on the resulting nanoscale foam structure. In situ tensile experiments are performed to observe how both individual ligaments and the foam structure's features change during deformation in real-time. We found two new morphology features that are independently controllable through synthesis parameters and are likely to influence mechanical stability while preserving or enhancing catalytic activity. The curvature of the ligaments can be increased by stirring the electrolyte during dealloying and the width of the ligament diameter size distribution can be adjusted by controlling the coarsening rate. In situ mechanical tests show that grain boundaries can influence crack propagation and that ligaments removed from the crack tip experience both elastic and plastic stress.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Constitutive behavior and progressive mechanical failure of electrodes in lithium-ion batteries

The electrodes of lithium-ion batteries (LIB) are known to be brittle and to fail earlier than the separators during an external crush event. Thus, the understanding of mechanical failure mechanism for LIB electrodes (anode and cathode) is critical for the safety design of LIB cells. In this paper, we present experimental and numerical studies on the constitutive behavior and progression of failure in LIB electrodes. Mechanical tests were designed and conducted to evaluate the constitutive properties of porous electrodes. Constitutive models were developed to describe the stress-strain response of electrodes under uniaxial tensile and compressive loads. The failure criterion and a damage model were introduced to model their unique tensile and compressive failure behavior. The failure mechanism of LIB electrodes was studied using the blunt rod test on dry electrodes, and numerical models were built to simulate progressive failure. The different failure processes were examined and analyzed in detail numerically, and correlated with experimentally observed failure phenomena. Finally, the test results and models improve our understanding of failure behavior in LIB electrodes, and provide constructive insights on future development of physics-based safety design tools for battery structures under mechanical abuse.

25 ENERGY STORAGE↗

Quantifying the Influence of Charge Rate and Cathode-Particle Architectures on Degradation of Li-Ion Cells Through 3D Continuum-Level Damage Models

In this article, we develop a 3D, continuum-level damage model implemented on statistically generated LiNi 0.5 Mn 0.3 Co 0.2 O (NMC 532) secondary cathode particles. The primary motivation of the particle-level model is to inform cathode-particle design through detailed exploration of the influence of secondary and primary particle sizes on the damage predicted during operation, and determine charging profiles that reduce cathode fracture. The model considers NMC 532 secondary particles containing an agglomeration of anisotropic, randomly oriented grains. These brittle, Ni-based cathodes are prone to mechanical degradation, which reduces overall battery cycle life. The model predicts that secondary-particle fracture is primarily due to non-ideal grain interactions and high-rate charge demands. The model predicts that small secondary-particles with large grains develop significantly less damage than larger secondary particles with small grains. The model predicts most of the chemo-mechanical damage accumulates in the first few cycles. The chemo-mechanical model predicts monotonically increasing capacity fade with cycling and rate. Comparing to experimental results, the model is well suited for capturing initial capacity fade mechanisms, but additional physics is required to capture long-term capacity fade effects.

25 ENERGY STORAGE↗

In-situ electrochemical optical techniques in the investigation of lithium interfacial phenomena with a liquid and a solid-state electrolyte

An in-situ electrochemical optical diagnosis is the key to the investigation of electrode interface during a redox reaction. Because the morphology changes particularly, dendrite formation, dendrite shapes, solid electrolyte interface formation and gas generation can be revealed visually. The challenge of ensuring uniform current density on a flat Li anode in a liquid electrolyte was addressed and uniform Li plating was demonstrated. The dendrite shape change under different reduction current density was discussed. Here the Li dendrite shape change and the performance of Li anodes with a surface lamination of graphite and red phosphate were used as examples to demonstrate the capability of the in-situ optical cell. An in-situ electrochemical optical cell used in the investigation of the increasingly popular solid-state Li batteries has its own challenges. Due to the untransparent nature of a solid-state electrolyte, an optical investigation on a solid-state electrolyte Li battery needs to be done by exposing the cross-section of the cell. In addition, it is very difficult to assemble an optical cell with a brittle and fragile solid-state electrolyte in a glove box. A set of formation and transfer dies, and an optical cell were introduced. The Li dendrite growth at the interface can be observed in a solid-state Li cell.

25 ENERGY STORAGE↗

Observation and Modeling of Dynamic Fracture Behaviors of Battery Cell Under Impact Loading Using Enhanced Representative Volume Element Concept

The burgeoning electric automobile industry has increased interest in battery safety. Battery cells experience significant mechanical stress during operation, including the impact of accidents and vibrations from driving. The potential for thermal runaway reactions in battery cells raises safety concerns. Although numerous researchers have defined the dynamic behavior of battery cells and proposed numerical models to describe it, few studies have focused on the high-strain rate mechanical impact phase correlated with the onset of fracture. In this study, we describe the dynamic behavior of pouch battery cells and propose a modeling method to study their mechanical failure under impact situations. Impact tests are conducted at various velocities and heights. To overcome numerical issues commonly encountered under rapid deformation scenarios, a new finite element model is developed based on the representative volume element model. The proposed approach efficiently simulates continuous crack propagation and brittleness behavior during impact by permitting the individual behavior of the cell components. Therefore, engineers can reliably design safer electric vehicle battery cells by measuring the properties of the cell components.

ENERGY STORAGE↗

Impact of supercritical carbon dioxide on the frictional strength of and the transport through thin cracks in shale

Understanding the mechanical and transport behavior of thin (i.e. small aperture) cracks slipping under supercritical carbon dioxide (sc-CO 2 ) conditions is essential to evaluate the integrity of sealing formations with buoyant sc-CO 2 below and the success of waterless fracturing. The two major items of interest in this work are frictional strength and permeability change of the crack. We used a triaxial cell that permits in situ visualization to conduct and monitor slippage along the faces of narrow cracks subjected to triaxial stresses. Such cracks are analogs to small geological faults. We tested carbonate-rich, 1-inch diameter Wolfcamp shale samples that are saw cut 30° to vertical to create a thin crack. Friction coefficients ranged from about 0.6 to 0.8 consistent with expectations for brittle rocks. The sc-CO 2 generally did not alter friction coefficient over the time scale of experiments. From a transport perspective, saturating cracks with sc-CO 2 substantially decreased permeability of the crack by 26%–52%, while slip resulted in a variety of permeability responses. Overall, the combined impact of sc-CO 2 saturation and slip reduced fault permeability for all tests. Our observations support the notion that the sealing capacity of some caprocks improves when saturated with sc-CO 2 and that some slip of small fractures is not necessarily detrimental to caprock integrity.

58 GEOSCIENCES↗

The influence of preexisting host rock damage on fault network localization

The transition from stable to unstable fracture propagation occurs when fractures begin to interact and link. Thus, fracture network coalescence controls how rocks and engineered structures fail. Here, to constrain the factors that influence localization in shear zones under brittle conditions, we build discrete element method models with a rough fault embedded in a shear zone. We add varying numbers of diffuse, randomly-placed weaknesses to examine the influence of diffuse damage on fracture network localization. The number of weaknesses controls the localization behavior of the fault network and the final fault geometry. We quantify localization using the Gini coefficient of the fracture volume, which measures the nonuniformity in a population. Each model generally increases in localization toward failure. However, models with more diffuse damage experience delocalization phases that are superimposed on the overall trend of increasing localization. The observed link between delocalization and host rock damage may help explain the varying localization of low magnitude seismicity in southern California. Models with more diffuse damage produce more complex fault geometries comprised of several parallel strands of wing cracks. The propagation of these wing cracks reduces the shear stress acting on the model boundaries, indicating that this fracture development increases the mechanical efficiency of the system.

58 GEOSCIENCES↗

The thermal regime of the Campi Flegrei magmatic system reconstructed through 3D numerical simulations

In this paper, we illustrate a quantitative conductive/convective thermal model incorporating a wide range of geophysical, petrological, geological, geochemical and isotopical observations that constrain the thermal evolution and present state of the Campi Flegrei caldera (CFc) magmatic system. The proposed model has been computed on the basis of the current knowledge of: (1) the volcanic and magmatic history of the volcano over the last 44 ka, (2) its underlying crustal structure, and (3) the physical properties of the erupted magmas. 3D numerical simulations of heat conduction and convection within heterogeneous rock/magma materials with evolving heat sources and boundary conditions that simulate magma rise from a deep (≥ 8 km depth) to shallow (2–6 km) reservoirs, magma chamber formation, magma extrusion, caldera collapse, and intra-caldera hydrothermal convection, have been carried out. The evolution of the CFc magmatic system through time has been simulated through different steps related to its changes in terms of depth, location and size of magma reservoirs and their replenishment. The thermal modeling results show that both heat conduction and convection have played an important role in the CFc thermal evolution, although with different timing. Finally, the simulated present heat distribution is in agreement with the measured geothermal profiles (Agip, 1987), reproduces the thermal gradient peaks at the CFc margins in correspondence to the anomalies in surface gradients (Corrado et al., 1998), and suggests temperatures of 700 °C at depth of 4 km in the central portion of the caldera, in agreement with the estimated temperature for the brittle-ductile transition (Hill, 1992).

3D conductive/convective model↗

Evaluation of toughness deterioration by an electrochemical method in an isothermally-aged N-containing austenitic stainless steel

This work presents the results of an evaluation of the deterioration of cryogenic toughness by means of an electrochemical method in a N-containing austenitic stainless steel (JK2) aged at temperatures of 700, 800 and 900 deg. C for times from 10 to 1000 min. The aging process at 700 and 800 deg. C caused the decrease in the Charpy V-Notch impact energy at - 196 deg. C because of the intergranular precipitation of carbides. Scanning electron micrographs of the Charpy V-Notch test specimens showed the presence of intergranular brittle fracture. The degree of sensitization was determined by the ratio of the maximum current density generated by the reactivation scan to that of the anodic scan, I{sub r}/I{sub a}, using the double-loop electrochemical potentiokinetic reactivation test. The Charpy V-Notch impact energy decreased with increase in the I{sub r}/I{sub a} ratio. This relation permits an estimate of the deterioration of cryogenic toughness due to thermal aging in this type of steel.

36 MATERIALS SCIENCE↗

SEM/AFM studies of cementitious binder modified by MWCNT and nano-sized Fe needles

Several compositions of cement paste samples containing multiwalled carbon nanotubes were produced using a small-size vacuum mixer. The mixes had water-to-binder ratios of 0.25 and 0.3. Sulfate resistant cement has been used. The multiwalled carbon nanotubes were introduced as a water suspension with added surfactant admixtures. The used surfactant acted as plasticizing agents for the cement paste and as dispersant for the multiwalled carbon nanotubes. A set of beams was produced to determine the compressive and flexural strengths. The scanning electron microscope and atomic force microscope studies of fractured and polished samples showed a good dispersion of multiwalled carbon nanotubes in the cement matrix. The studies revealed also sliding of multiwalled carbon nanotubes from the matrix in tension which indicates their weak bond with cement matrix. In addition to multiwalled carbon nanotubes also steel wires covered with ferrite needles were investigated to determine the bond strength between the matrix and the steel wire. These later samples consisted of 15-mm-high cylinders of cement paste with vertically cast-in steel wires. As reference, plain steel wires were cast, too. The bond strength between steel wires covered with nano-sized Fe needles appeared to be lower in comparison with the reference wires. The scanning electron microscope studies of fractured samples indicated on brittle nature of Fe needles resulting in shear-caused breakage of the bond to the matrix.

36 MATERIALS SCIENCE↗

Effect of cryo-induced microcracks on microindentation of hydrated cortical bone tissue

Microcracks accumulate in cortical bone tissue as a consequence of everyday cyclic loading. However, it remains unclear to what extent microdamage accumulation contributes to an increase in fracture risk. A cryo-preparation technique was applied to induce microcracks in cortical bone tissue. Microcracks with lengths up to approximately 20 {mu}m, which were initiated mainly on the boundaries of haversian canals, were observed with cryo-scanning electron microscopy. A microindentation technique was applied to study the mechanical loading effect on the microcracked hydrated bone tissue. The microindentation patterns were section-scanned using confocal laser scanning microscopy to understand the deformation and bone damage mechanisms made by mechanical loading. The results show that there was no significant difference with respect to microhardness between the original and microcracked hydrated cortical bone tissues (ANOVA, p > 0.05). The cryo-induced microcracks in the bone tissue were not propagated further under the mechanical loads applied. The deformation mechanism of the microcracked cortical bone tissue was plastic deformation, not brittle fracture.

36 MATERIALS SCIENCE↗

Characterization of industrially produced galvannealed coating using cross-sectional specimen in TEM

Galvannealed coated sheet steels are extensively used in the automotive industry due to their inherent advantages, as compared to other zinc based coating, such as excellent spot weldability, good corrosion resistance and better paintability. Despite the above advantages, galvannealed coating suffers from poor formability due to the presence of hard and brittle Fe-Zn intermetallic phases. The formability of the coating depends on the amount and orientation of different Fe-Zn intermetallic phases. The present study deals with the characterization of an industrially produced galvannealed coating using cross-sectional specimen in a Transmission Electron Microscope. From the selected area diffraction patterns obtained in Transmission Electron Microscope, the orientations of the delta phase were calculated.

36 MATERIALS SCIENCE↗

X-ray diffraction line profile analysis of deformation microstructure in boron modified Ti-6Al-4V alloy

X-ray diffraction line profile analysis (XRDLPA) techniques have been applied to investigate the deformed microstructure of a recently developed boron modified two-phase titanium alloy Ti-6Al-4V. The alloy was hot compressed at 750 deg. C up to 50% height reduction at two different strain rates (10{sup -3} S{sup -1} and 1 S{sup -1}). Microstructural parameters like average domain size, average microstrain within the domain and dislocation density of the two phases were determined using X-ray diffraction line profile analysis. The results indicate an increase in the microstrain and dislocation density for the {alpha}-phase and decrease for the {beta}-phase in the case of boron modified alloys as compared to the normal material. Microstructural modifications viz. the grain refinement and the presence of hard, brittle TiB particles in the case of boron modified alloy are held responsible for the observed difference in the dislocation density. - Research Highlights: {yields} Microstructural examination of hot compressed Ti64 with and without boron addition by XRDLPA. {yields} Smaller average domain size in alpha-phase compared to the corresponding alpha-phase in all cases. {yields} Higher microstrain and dislocation density for {alpha} phase and lower for {beta} phase in case of Ti64+B. {yields} Decrease in domain size while increase in micro-strain and dislocation density with strain rate. {yields} Strain accumulation around TiB particles responsible for high dislocation density in {alpha} phase.

36 MATERIALS SCIENCE↗