Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Advanced materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Maypole (Hoop/Column) concept development program

The program is divided into six tasks: preliminary design and performance; materials development; advanced concepts; economic assessment; demonstration/verification models; and a 15 meter engineering model. All support the main objective of the program which is the technology development necessary to evaluate, design, manufacture, package, transport and deploy the Hoop/Column reflector by means of a ground-based test program. Progress for each task is reported.

Sullivan, M. R.↗
NASA NTRS1981

Advanced oxygen-hydrocarbon Earth-to-orbit propulsion

Liquid oxygen/hydrocarbon (LO2/HC) rocket engine cycles for a surface to orbit transportation system were evaluated. A consistent engine system data base is established for defining advantages and disadvantages, system performance and operating limits, engine parametric data, and technology requirements for candidate engine systems. Preliminary comparisons of the engine cycles utilizing delivered specific impulse values are presented. Methane and propane staged combustion cycles are the highest LO2/HC performers. The hydrogen cooled LO2/methane dual throat engine was found to be the highest performing. Technology needs identified in the study include: high temperature turbines; oxidizer-rich preburners; LO2, methane, and propane cooling; methane and propane fuel-rich preburners; the HC fuel turbopump; and application of advanced composite materials to the engine system. Parametric sensitivity analysis data are displayed which show the effect of variations in engine thrust, mixture ratio, chamber pressure, area ratio, cycle life, and turbine inlet temperature on specific impulse and engine weight.

Obrien, C. J.↗
NASA NTRS1982

Oxidation stability of advanced reaction-bonded Si3N4 materials

Four slip-cast, injection-molded and isostatically-pressed specimens of reaction-bonded silicon nitride (RBSN) were subjected to static oxidation tests at 900 C for 10 hours. Specimens containing 8-10% interconnected open porosity of size greater than one micron exhibited a 20-30% decrease in average room temperature four-point flexure strength, while those with 10% open porosity of magnitudes much smaller than one micron as well as those with 2-4% interconnected open porosity of about one micron did not decrease in strength after 900 C exposure. It was determined that preoxidation treatment at 1350 C prevents the 20-30% strength degradation due to internal oxidation, and evidence is presented which suggests that surface pit formation in some RBSN may result from contamination by the furnace environment rather than any intrinsic material properties.

Lindberg, L. J.↗
NASA NTRS1982

SiC or B4C-B/low strategic element content composite

Advancements in materials technologies are needed to provide the aerospace industry with alternate material options in the event of future strategic metal shortages and to optimize performance of engines. Composite materials are promising candidates for such an application. The potential of SiC and B4C-B filament reinforced low strategic element iron-base alloy content composites or use at 760 to 870 C is considered. A limiting factor towards developing this material for high temperature use has been the reaction between the filament and matrix material during fabrication and service which degrades filament strength. A low temperature fabrication process to limit filament/matrix reaction is being developed which involves the use of hollow cathode sputtering to coat the filaments with iron-base alloys of various compositions. An investigation is being conducted to determine the interfacial reaction effects of SiC and B4C-B filaments with iron-base alloys to develop an understanding of filament/matrix alloy compatibility for 760 to 870 C service.

Petrasek, D. W.↗
NASA NTRS1982

Recent advances in carbon-carbon materials systems

Carbon-carbon materials and new oxidation resistant coating developments are discussed. Potential areas of application are highlighted. A short bibliography of selected references is included that describe carbon-carbon materials and related technology in detail.

Donald R. Rummler↗
NASA NTRS1983

Proceedings of the 21st Project Integration Meeting

Progress made by the Flat Plate Solar Array Project during the period April 1982 to January 1983 is described. Reports on polysilicon refining, thin film solar cell and module technology development, central station electric utility activities, silicon sheet growth and characteristics, advanced photovoltaic materials, cell and processes research, module technology, environmental isolation, engineering sciences, module performance and failure analysis and project analysis and integration are included.

Source record↗
NASA NTRS1984

Hygrothermal influence on delamination behavior of graphite/epoxy laminates

The hygrothermal effect on the fracture behavior of graphite-epoxy laminates was investigated to develop a methodology for damage tolerance predictions in advanced composite materials. Several T300/934 laminates were tested using a number of specimen configurations to evaluate the effects of temperature and humidity on delamination fracture toughness under mode 1 and mode 2 loading. It is indicated that moisture has a slightly beneficial influence on fracture toughness or critical strain energy release rate during mode 1 delamination, but has a slightly deleterious effect on mode 2 delamination and mode 1 transverse cracking. The failed specimens are examined by SEM and topographical differences due to fracture modes are identified. It is concluded that the effect of moisture on fracture topography can not be distinguished.

Garg, A.↗
NASA NTRS1984

Design of a composite wing extension for a general aviation aircraft

A composite wing extension was designed for a typical general aviation aircraft to improve lift curve slope, dihedral effect, and lift to drag ratio. Advanced composite materials were used in the design to evaluate their use as primary structural components in general aviation aircraft. Extensive wind tunnel tests were used to evaluate six extension shapes. The extension shape chosen as the best choice was 28 inches long with a total area of 17 square feet. Subsequent flight tests showed the wing extension's predicted aerodynamic improvements to be correct. The structural design of the wing extension consisted of a hybrid laminate carbon core with outer layers of Kevlar - layed up over a foam interior which acted as an internal support. The laminate skin of the wing extension was designed from strength requirements, and the foam core was included to prevent buckling. A joint lap was recommended to attach the wing extension to the main wing structure.

Adney, P. S.↗
NASA NTRS1984

Development of partially fluorinated resin apex seals

Partially fluorinated polyimides were prepared and molded in the form of discs and pins for test as potential apex seal materials for advanced rotary combustion engines. The polyimides were formulated from the diamine 2,2-bis 4-(4-aminophenoxy)phenyl hexafluoropropane (4-BDAF) and the dianhydrides of pyromellitic acid (PMDA) and benzophenonetetracarboxylic acid (BTDA). Tribological testing was performed at sliding speeds of 0.31 to 11.6 m/s and at temperatures of from 298K to 573K. It is shown that the carbon fiber filled polyimides, particularly the 80/20 compositions, have an excellent balance of wear/friction at 573K. The unfilled, 80/20 and 60/40 compositions indicate an unusual combination of high friction and low wear which may be advantageous in such applications as brakes and traction drives.

Green, H. E.↗
NASA NTRS1982

Advanced Strain-Isolation-Pad Material with Bonded Fibrous Construction

The feasibility of utilizing air lay and liquid lay felt deposition techniques to fabricate strain isolation pad (SIP) materials for the Space Shuttle Orbiter was demonstrated. These materials were developed as candidate replacements for the present needled felt SIP used between the ceramic tiles and the aluminum skin on the undersurface of the Orbiter. The SIP materials that were developed consisted of high temperature aramid fibers deposited by controlled fluid (air or liquid) carriers to form low density unbonded felts. The deposited felts were then bonded at the fiber intersections with a small amount of high temperature polyimide resin. This type of bonded felt construction can potentially eliminate two of the problems associated with the present SIP, viz., transmittal of localized stresses into the tiles and load history dependent mechanical response. However, further work is needed to achieve adequate through thickness tensile strength in the bonded felts.

Seibold, R. W.↗
NASA NTRS1985

Hygrothermal influence on delamination behavior of graphite/epoxy laminates

The hygrothermal effect on the fracture behavior of graphite-epoxy laminates was investigated to develop a methodology for damage tolerance predictions in advanced composite materials. Several T300/934 laminates were tested using a number of specimen configurations to evaluate the effects of temperature and humidity on delamination fracture toughness under mode 1 and mode 2 loading. It is indicated that moisture has a slightly beneficial influence on fracture toughness or critical strain energy release rate during mode 1 delamination, but has a slightly deleterious effect on mode 2 delamination, and mode 1 transverse cracking. The failed specimens are examined by SEM and topographical differences due to fracture modes are identified. It is concluded that the effect of moisture on fracture topography can not be distinguished.

Garg, A.↗
NASA NTRS1985

Theoretical Problems in Materials Science

Interactions between theoretical physics and material sciences to identify problems of common interest in which some of the powerful theoretical approaches developed for other branches of physics may be applied to problems in materials science are presented. A unique structure was identified in rapidly quenched Al-14% Mn. The material has long-range directed bonds with icosahedral symmetry which does not form a regular structure but instead forms an amorphous-like quasiperiodic structure. Finite volume fractions of second phase material is advanced and is coupled with nucleation theory to describe the formation and structure of precipitating phases in alloys. Application of the theory of pattern formation to the problem of dendrite formation is studied.

Langer, J. S.↗
NASA NTRS1985

Fracture characteristics of angleplied laminates fabricated from overaged graphite/epoxy prepreg

A series of angleplied graphite/epoxy laminates was fabricated from overaged prepreg and tested in tension to investigate the effects of overaged or advanced cure material on the degradation of laminate strength. Results, which include fracture stresses, indicate a severe degradation in strength. In addition, the fracture surfaces and microstructural characteristics are distinctly unlike any features observed in previous tests of this prepreg and laminate configuration. Photographs of the surfaces and microstructures reveal flat morphologies consisting of alternate rows of fibers and hackles. These fracture surface characteristics are independent of the laminate configurations. The photomicrographs are presented and compared with data from similar studies to show the unique characteristics produced by the overage prepreg. Analytical studies produced results which agreed with those from the experimental investigations.

Ginty, C. A.↗
NASA NTRS1984

Highly Maneuverable Aircraft Technology (HiMAT) flight-flutter test program

The highly maneuverable aircraft technology (HiMAT) vehicle was evaluated in a joint NASA and Air Force flight test program. The HiMAT vehicle is a remotely piloted research vehicle. Its design incorporates the use of advanced composite materials in the wings, and canards for aeroelastic tailoring. A flight-flutter test program was conducted to clear a sufficient flight envelope to allow for performance, stability and control, and loads testing. Testing was accomplished with and without flight control-surface dampers. Flutter clearance of the vehicle indicated satisfactory damping and damping trends for the structural modes of the HiMAT vehicle. The data presented include frequency and damping plotted as a function of Mach number.

Kehoe, M. W.↗
NASA NTRS1985

Efficient frequency conversion of laser sources in nonlinear crystals

The use of nonlinear crystals to extend the frequency range of solid-state laser sources is proposed. The harmonic generation of high-average-power laser sources and CW-laser-sources nonlinear crystals is considered. The development of Nd:YAG pumped parametric oscillators and optical parametric amplifiers using LiNbO3 or AgGaS2 is studied. The LiNbO3 oscillator has tunable output over the 1.4-4.0 micron range and is applicable for remote sensing measurements of molecules and of humidity and temperature; AgGaS2 oscillators provide the potential for 3-15 micron infrared generation. Advances in material synthesis techniques related to the design and synthesis of nonlinear media are discussed. Various procedures for the synthesis of nonlinear crystals are described.

Byer, R. L.↗
NASA NTRS1987

Making a Silicon-Nitride/Silicon-Carbide Composite

Hot pressing and nitriding produce strong fiber/matrix material. Fabrication method developed for processing strong and tough silicon-based ceramic composite material, SiC/RBSN, which consists of reaction-bonded Si3N4 (RBSN) reinforced by continuous-length, high-modulus, high strength silicon carbide (SiC) fibers prepared by chemical-vapor deposition method. Increased toughness and ultimate strength of SiC/RBSN composite makes it potential structural material for advanced heat engines.

Bhatt, R. T.↗
NASA NTRS1987

Corrosion of SiC by Molten Salt

Advanced ceramic materials considered for wide range of applications as in gas turbine engines and heat exchangers. In such applications, materials may be in corrosive environments that include molten salts. Very corrosive to alloys. In order to determine extent of problem for ceramic materials, corrosion of SiC by molten salts studied in both jet fuel burners and laboratory furnaces. Surface of silicon carbide corroded by exposure to flame seeded with 4 parts per million of sodium. Strength of silicon carbide decreased by corrosion in flame and tube-furnace tests.

Jacobson, Nathan S.↗
NASA NTRS1987

A prediction model of the depth-of-discharge effect on the cycle life of a storage cell

Cycle life requirements are very high for batteries used in aerospace applications in low Earth orbit. The data base required to establish confidence in a particular cell design is thus both extensive and expensive. Reliable accelerated cycle life testing and performance decay modeling represent attractive alternatives to real-time tests of cycle life. In light of certain long-term cycle life test results, this paper examines a very simple performance decay model developed earlier. Application of that model to available data demonstrates a rigid relationship between a battery's expected cycle life and the depth of discharge of cycling. Further, modeling analysis of the data suggests that a significantly improved cycle life can be obtained with advanced components, materials, and designs; and that cycle life can be reliably predicted from the results of accelerated testing.

Thaller, Lawrence H.↗