Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ASSISTED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Microwave-Assisted Combustion Synthesis of ZnO:Eu Nanoparticles: Effect of Fuel Types

Nanoparticles of Europium oxide doped with Zinc oxide were synthesized via microwave-assisted combustion method. Citric acid as a simultaneous fuel and chelating agent and glycine as a fuel and mixture of these fuels were sleeted. X-Ray diffraction patterns (XRD) indicated the formation of ZnO structure with a few amount of Eu{sub 2}O{sub 3} phase. Fourier transformation infra red (FTIR) spectra reveal the increase of ZnO{sub 4} bonds with glycine content of fuels mixture. Scanning electron microscope (SEM) images showed the conversion of nanosphere to spongy-like structure with respect to change of fuel mixtures from citric to glycine. From transmission electron microscopy (TEM) nanoparticles of a mean size 30 nm are observed Green fluorescence emission of different samples was due to activation of self activated center of ZnO structure through transition of electron from Eu{sup 3+} to V{sub zn} sites.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Sensitive Fluorescent Determination of Cobalt by Microwave Assisted Synthesized TPTZ Functionalized Carbon Dots

Novel fluorescent carbon dots (CDs) for cobalt ions sensing were synthesized from 2,4,6-tris(2′-pyridyl)-s-triazine (TPTZ) and citric acid by microwave-assisted method in one pot. This sensor was water soluble, simple, sensitive and cheap. The size of the CDs was determined from transmission electron microscope image and was in the range of 10 nm. Under optimized experimental conditions, this luminescent system had stable response for Co (II) over a concentration range from 0.4 to 50 µM with a detection limit as low as 230 nM. The proposed method showed good sensitivity and selectivity with respect to interference ions. Finally, this system was used for Co (II) determination in tap water, river water and mineral water and B{sub 12} ampoule samples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Application of Genetic Algorithm (GA) Assisted Partial Least Square (PLS) Analysis on Trilinear and Non-trilinear Fluorescence Data Sets to Quantify the Fluorophores in Multifluorophoric Mixtures: Improving Quantification Accuracy of Fluorimetric Estimations of Dilute Aqueous Mixtures

Excitation-emission matrix fluorescence (EEMF) and total synchronous fluorescence spectroscopy (TSFS) are the 2 fluorescence techniques that are commonly used for the analysis of multifluorophoric mixtures. These 2 fluorescence techniques are conceptually different and provide certain advantages over each other. The manual analysis of such highly correlated large volume of EEMF and TSFS towards developing a calibration model is difficult. Partial least square (PLS) analysis can analyze the large volume of EEMF and TSFS data sets by finding important factors that maximize the correlation between the spectral and concentration information for each fluorophore. However, often the application of PLS analysis on entire data sets does not provide a robust calibration model and requires application of suitable pre-processing step. The present work evaluates the application of genetic algorithm (GA) analysis prior to PLS analysis on EEMF and TSFS data sets towards improving the precision and accuracy of the calibration model. The GA algorithm essentially combines the advantages provided by stochastic methods with those provided by deterministic approaches and can find the set of EEMF and TSFS variables that perfectly correlate well with the concentration of each of the fluorophores present in the multifluorophoric mixtures. The utility of the GA assisted PLS analysis is successfully validated using (i) EEMF data sets acquired for dilute aqueous mixture of four biomolecules and (ii) TSFS data sets acquired for dilute aqueous mixtures of four carcinogenic polycyclic aromatic hydrocarbons (PAHs) mixtures. In the present work, it is shown that by using the GA it is possible to significantly improve the accuracy and precision of the PLS calibration model developed for both EEMF and TSFS data set. Hence, GA must be considered as a useful pre-processing technique while developing an EEMF and TSFS calibration model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enzyme-Assisted Extraction and Pb{sup 2+} Biosorption of Polysaccharide from Cordyceps militaris

The enzyme assisted extraction conditions of polysaccharide from Cordyceps militaris mycelia were firstly investigated by kinetics analysis and the optimal operating was found to be: extraction temperature 40 °C; solid-solvent ratio 1:20; extraction pH 4.0; cellulase concentration 2.0%. The polysaccharide extraction yield was 5.99% under these optimized conditions. Furthermore, a fundamental investigation of the biosorption of Pb{sup 2+} from aqueous solution by the C. militaris polysaccharide was performed under batch conditions. The suitable pH (5.0), polysaccharide concentration (0.20 g L{sup −1}), initial Pb{sup 2+} concentration (300 mg L{sup −1}) and contact time (40 min) were outlined to enhance Pb{sup 2+} biosorption from aqueous medium. The Langmuir isotherm model and pseudo first order kinetic model fitted well to the data of Pb{sup 2+} biosorption, suggesting the biosorption of Pb{sup 2+} onto C. militaris polysaccharide was monolayer biosorption and physical adsorption might be the rate-limiting step that controlled the adsorption process. FTIR analysis showed that the main functional groups of C. militaris polysaccharide involved in adsorption process were carbonyl, carboxyl, and hydroxyl groups.

36 MATERIALS SCIENCE↗

Optimization of Microwave-Assisted Preparation of TPA from Waste PET Using Response Surface Methodology

Terephthalic acid (TPA) was prepared from waste polyethylene terephthalate by microwave-assisted depolymerization with TOMAB as catalyst, the structure and properties of TPA were elucidated by using physico-chemical and spectroscopic methods. Single-factors experiments demonstrated that the TPA yield was affected significantly by the factors of catalyst and alkali amount, depolymerization temperature and time. The effects of variables, including catalyst and alkali amount, depolymerization temperature and time, on the TPA yield were evaluted by response surface methodology with a Box-Behnken design. The modified and verified experiments were completed after considering product performance and actual operation, the optimum parameters were determined to be TOMAB 2.7 g, 15% NaOH 260 mL, temperature 85 °C, degradation time 2.2 h. Under these conditions, the average yield of TPA in three replicated experiments is 97.53%, and this value is not significantly different from the value of 98.59% predicted by the model. These results demonstrate that this method is feasible.

36 MATERIALS SCIENCE↗

Conferring Antibacterial Properties on Sesbania Gum via Microwave-Assisted Graft Copolymerization of DADMAC

Microbial contamination, the consequences of both anthropogenic and geogenic activity, includes high health and environmental threats and may adversely affects the ecological niche. The present work is a successful attempt towards the fabrication of anti-bacterial agent by incorporation of cationic monomer, diallyldimethylammonium chloride (DADMAC) on sesbania gum through microwave assisted method. The grafted chains of poly (DADMAC) provide positive charge to sesbania gum which in turn confers antibacterial activity. The synthesized product was characterized through FTIR, SEM, TGA, DSC elemental and viscometric analysis. The inhibitory activity of the synthesized product has been evaluated in vitro against both Gram-positive (Staphylococcus aureus NCIM 2122 and Bacillus anthracis) as well as Gram-negative (Salmonella typhi NCIM 2501 and Escherichia coli NCIM 2832) bacteria through standard agar cup method. Optimum minimum inhibitory concentration for each grade of graft copolymer measured by calculating the zone of inhibition has been found at 750 µg/ml. Graphical Abstract: .

36 MATERIALS SCIENCE↗

Enhancement of Magnetization and Tailoring of Blocking Temperatures of Nano-Ni–Zn Ferrite Powder Synthesized Using Microwave-assisted Combustion Method

Single-phase nano-Ni–Zn ferrite samples in the range of 6 to 75 nm were synthesized using microwave-assisted combustion method. Enhancement of saturation magnetization (M{sub s}) was observed in comparison with previously reported results. Minor variation of (M{sub s}) due to composition change can be explained on the basis of strengthening of A–B exchange interaction due to replacement of nonmagnetic Zn ions by Ni ions. Low coercivity (H{sub c}) and retentivity (M{sub r}) indicate low loss in the samples. SQUID analysis showed that the blocking temperature (T{sub B}) of the samples can be tailored in the present work.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural and Magnetic Properties of La-Substituted M-Type Hexagonal Sr–Ni Ferrites Synthesized by Ball-Milling-Assisted Ceramic Process

Sr{sub 0.5}Ni{sub 0.5}La{sub x}Fe{sub 12 − x}O{sub 19} (x = 0, 0.08, 0.16, and 0.24) hexaferrites have been synthesized by ball-milling-assisted ceramic process. The calcined samples are characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectra (FTIR), and vibrating sample magnetometry (VSM). XRD reveals that all samples consist of the main M-type hexagonal Sr ferrite phase and a low amount of rhombohedral Fe{sub 2}O{sub 3} as secondary phase, and a continuous increase of the hexagonal lattice parameters with substitution content (x). Magnetic characterization indicates that all Sr{sub 0.5}Ni{sub 0.5}La{sub x}Fe{sub 12 − x}O{sub 19} samples have a hard magnetic property. Substitution of Fe{sup 3+} ions by La{sup 3+} ions can obviously improve the specific saturation magnetization, remanence, magnetic moment, and effective anisotropy constant. Specific saturation magnetization, remanence, and the magnetic moment reach a maximum at x= 0.24 and calcination temperature of 1050 {sup ∘}C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermophysical Investigations of Ultrasonically Assisted Magnetic Nanofluids for Heat Transfer

The NiFe{sub 2}O{sub 4} magnetic nanoparticles synthesized and used to prepare stable water-based magnetic nanofluids of various concentrations by ultrasonically assisted two-step techniques. Thermophysical investigations are made on the nanofluids at different temperatures ranging from 20 to 80 °C. The measurements revealed that the thermal conductivity of nanofluids significantly enhances with an increase in the percentage of nanoparticle volume fraction. The thermal conductivity measurements showed that the maximum enhancement is 32.65% achieved at 1% nanoparticle volume fraction and at 80 °C. Specific heat of nanofluids was decreased with increasing nanoparticle volume fractions, and it augments with increasing temperature. Viscosity measurements showed that nanofluid had a Newtonian behavior at all nanoparticle volume fractions and temperatures considered. The viscosity of the nanofluid increased with increasing nanoparticle concentration and decreasing temperature. Experimental results revealed that the viscosity sensitivity to temperature variation is minor, while it is more sensitive to the variations of nanoparticle volume fraction. The density of nanofluids was increased with increasing nanoparticle volume fractions and decreased with increasing temperature. Lastly, efforts were made to provide a precise correlation to estimate the thermal conductivity, as well as other thermophysical properties at various temperatures and volume fractions of nanoparticles. The comparison between the results and the correlation results showed a good agreement.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

CTAB-Assisted Synthesis of N-Doped Fe{sub 3}C Nanowires and Their Magnetic Properties

N-doped iron carbide (N-doped Fe{sub 3}C) nanomaterials have a wide range of applications. In this study, a hexadecyltrimethylammonium bromide (CTAB)-assisted two-step process was used to prepare N-doped Fe{sub 3}C nanomaterials. The effect of CTAB addition on the phase, structure, and morphologies of the products has been investigated in detail based on the characterization results of X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), Raman spectra (Raman), N{sub 2} adsorption–desorption, and elemental analysis. By tuning the amount of CTAB, N-doped Fe{sub 3}C nanowires were prepared. The magnetic hysteresis loops at room temperature of the N-doped Fe{sub 3}C nanomaterials show ferromagnetic characteristics.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Chlorine-free, monolithic lanthanide series rare earth oxide aerogels via epoxide-assisted sol-gel method

Synthesis of chlorine-free, rare earth oxide aerogels from the lanthanide series was achieved using a modified epoxide-assisted sol-gel method. An ethanolic solution of the hydrated metal nitrate, propylene oxide, and ammonium carbonate was found to gel upon heating to 333 K. Critical point drying of the wet gel in CO 2 yielded monolithic aerogels. Most of the aerogels were amorphous as-prepared, but became nano-crystalline after calcination at 923 K in air. The aerogels had high surface areas (up to 150 m 2 /g), low densities (40–225 mg/cm 3 ), and were photoluminescent.

Rietveld refinement↗

Alloy-assisted Auger recombination in InGaN

It has been numerically investigated the effect of alloying on the Auger recombination rate in wurtzite type n-InGaN. In order to explicitly take into account the effect of alloy disorder, the calculations have been performed with a 256-atom supercell that includes In and Ga atoms randomly distributed over the supercell sites to obtain a given composition. A full band structure (no band scissors-shifting) and high-dense inhomogeneous k-point grid were used to improve the accuracy of the calculations. We show that the large number of allowed interband Auger transitions originated by the breaking of the translational periodicity plays a crucial role in the wide band gap InGaN alloys. The alloy-assisted Auger coefficients for these alloys are in the 1.0 × 10{sup −32}–4.7 × 10{sup −31} cm{sup 6}/s range.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Comparative study of energy and footprint minimization limit for two types of graphene-assisted ring-shape modulators

In this paper, a numerical investigation has been performed on the limits of miniaturization for a graphene-assisted modulator considering two different configurations, in both cases the critical coupling condition representing the OFF state, and the transmission level of − 3 dB the ON state. In addition, the power consumption per bit of 100 fJ/bit was established as the cutoff parameter for both modulator configurations, as well as the minimum chemical potential for the ON state of 0.4 eV for the hybrid modulator. Considering the parameters aforementioned, our results showed that both configurations of modulators have great potential of miniaturization, high modulation speed and low power consumption.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Experimental Investigation on Acoustic Control Droplet Transfer in Ultrasonic-Wave-Assisted Gas Metal Arc Welding

Ultrasonic-wave-assisted gas metal arc welding (U-GMAW) is a new, advanced arc welding method that uses an ultrasonic wave emitted from an ultrasonic radiator above the arc. However, it remains unclear how the ultrasonic wave affects the metal droplet, hindering further application of U-GMAW. In this paper, an improved U-GMAW system was used and its superiority was experimentally demonstrated. Then a series of experiments were designed and performed to study how the ultrasonic wave affects droplet transfer, including droplet size, velocity, and motion trajectory. The behavior of droplet transfer was observed in high-speed images. The droplet transfer is closely related to the distribution of the acoustic field, determined by the ultrasonic current. Moreover, by analyzing the variably accelerated motion of the droplet, the acoustic control of the droplet transfer was intuitively demonstrated. Finally, U-GMAW was successfully used in vertical-up and overhead welding experiments, showing that U-GMAW is promising for use in welding in all positions.

36 MATERIALS SCIENCE↗

Motion of Solid Grains During Magnetic Field-Assisted Directional Solidification

In this paper, we report the visible evidence for thermoelectric magnetic forces (TEMFs) during magnetic field-assisted directional solidification, and their potential to control the motion of solid grains(dendrite fragments or equiaxed grains). These motions are observed by means of synchrotron X-ray radiography and compared with analytic calculations for a spherical particle’s motion driven only by TEMFs, which confirms that the observed solid grain motions are the combined result of the TEMFs and gravity. We also carried out corresponding 3D numerical simulations to validate the calculations and further prove our conclusion that TEMF acts on the solid grain and affects its motion trajectory.

36 MATERIALS SCIENCE↗

An Electro-Assisted Powder Metallurgical Route for the Preparation of Porous Ti and NiTi in Molten CaCl{sub 2}

Molten salts can provide a high-temperature and oxygen-water-free environment, and the electrochemical polarization is able to reduce the oxide scale on the surface of Ti and Ni particles in molten salts and, thereby, enhance the sintering and accelerating atom diffusion between Ti and Ni. Thus, an electro-assisted powder metallurgical (EPM) approach was developed to prepare porous Ti and NiTi from metal powders in molten salts, where the porous pellet cathode made of the mixture of Ni and Ti powders is electrochemically polarized to facilitate the generation of the porous Ti and NiTi at a temperature lower than 1000 °C. The electrolytic product obtained under a cell voltage of 3 V for 12 hours is nearly pure NiTi with a tiny amount of undesired Ni{sub 3}Ti and NiTi{sub 2} phases. Overall, the EPM route could be a straightforward and general way to prepare porous Ti and Ti-alloys for implants and other applications.

36 MATERIALS SCIENCE↗

Low-Temperature Synthesis of VB{sub 2} Nanopowders by a Molten-Salt-Assisted Borothermal Reduction Process

Vanadium diboride (VB{sub 2}) powders with low oxygen content are prepared via a molten-salt-assisted borothermal reduction reaction at 1123 K to 1273 K (850 °C to 1000 °C) using V{sub 2}O{sub 3} and boron powders as the raw materials. The effects of the amount of molten salt and reaction temperature on the phase transition and morphology of the final products are investigated. The results reveal that the addition of molten salt is beneficial for decreasing both the synthesis temperature and particle size of the final products. When the mass ratio of NaCl to reactants is 0.75:1, the VB{sub 2} powders prepared at 1173 K (900 °C) have a particle size lower than 100 nm. Too little or too high molten salt addition has a negative impact on the preparation of the VB{sub 2} powders. Furthermore, the reaction temperature has an important impact on the morphology and purity of the VB{sub 2} particles. An appropriate reaction temperature (1173 K (900 °C)) is beneficial for controlling the size of the VB{sub 2} particles in the order of nanoscale and improving the quality of the VB{sub 2} powders.

36 MATERIALS SCIENCE↗

Effect of Electropulsing-Assisted Ultrasonic Nanocrystalline Surface Modification on the Surface Mechanical Properties and Microstructure of Ti-6Al-4V Alloy

The effect of electropulsing-assisted ultrasonic nanocrystalline surface modification (EP-UNSM) on surface mechanical properties and microstructure of Ti-6Al-4V alloy is investigated. Compared to conventional ultrasonic nanocrystalline surface modification (UNSM), EP-UNSM can effectively facilitate surface roughness and morphology, leading to excellent surface roughness (reduced from Ra 0.918 to Ra 0.028 μm by UNSM and Ra 0.019 μm by EP-UNSM) and smoother morphology with less cracks and defects. Surface friction coefficients are enhanced, resulting in lower and smoother friction coefficients. In addition, the surface-strengthened layer and ultra-refined grains are significantly enhanced with more severe plastic deformation and a greater surface hardness (a maximum hardness value of 407 HV and an effective depth of 550 μm, in comparison with the maximum hardness value of 364 HV and effective depth of 300 μm obtained by conventional UNSM). Remarkable enhancement of surface mechanical properties can be attributed to the refined gradient microstructure and the enhanced severe plastic deformation layer induced by coupling the effects of UNSM and electropulsing. The accelerated dislocation mobility and atom diffusion caused by the thermal and athermal effects of electropulsing treatment may be the primary intrinsic reasons for these improvements.

36 MATERIALS SCIENCE↗