Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ANTIMONY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Epitaxy of Ge-Sb-Te phase-change memory alloys

The authors demonstrate the epitaxy of Ge-Sb-Te alloys close to the Ge{sub 2}Sb{sub 2}Te{sub 5} composition on GaSb(001). Using molecular beam epitaxy with elemental sources, amorphous films are obtained at growth temperatures below 120 deg. C and films with a cubic structure and a predominant cube-on-cube epitaxial relationship above 180 deg. C. Using a high-power pulsed laser, the epitaxial films are switched between the crystalline and the amorphous phases. Streaks in the diffraction data help to resolve the apparent ambiguity in interatomic distances between earlier x-ray absorption and powder diffraction measurements. The structural changes are confirmed by Raman spectroscopy.

36 MATERIALS SCIENCE↗

Phase transitions in Ge-Sb phase change materials

Thin films of the phase change material Ge-Sb with Ge concentrations between 7.3 and 81.1 at. % were deposited by cosputtering from elemental targets. Their crystallization behavior was studied using time-resolved x-ray diffraction, Auger electron spectroscopy, differential scanning calorimetry, x-ray reflectivity, profilometry, optical reflectivity, and resistivity versus temperature measurements. It was found that the crystallization temperature increases with Ge content. Calculations of the glass transition temperature (which is a lower limit for the crystallization temperature T{sub x}) also show an increase with Ge concentration closely tracking the measured values of T{sub x}. For low Ge content samples, Sb x-ray diffraction peaks occurred during a heating ramp at lower temperature than Ge diffraction peaks. The appearance of Ge peaks is related to Ge precipitation and agglomeration. For Ge concentrations of 59.3 at. % and higher, Sb and Ge peaks occurred at the same temperature. Upon crystallization, film mass density and optical reflectivity increase as well as electrical contrast (ratio of resistivity in amorphous phase to crystalline phase) all showed a maximum for the eutectic alloy (14.5 at. % Ge). For the alloy with 59.3 at. % Ge there was very little change in any of these parameters, while the alloy with 81.1 at. % Ge behaved opposite to a typical phase change alloy and showed reduced mass density and reflectivity and increased resistivity.

36 MATERIALS SCIENCE↗

Unique nanostructures and enhanced thermoelectric performance of melt-spun BiSbTe alloys

We report a melt spinning technique followed by a quick spark plasma sintering procedure to fabricate high-performance p-type Bi{sub 0.52}Sb{sub 1.48}Te{sub 3} bulk material with unique microstructures. The microstructures consist of nanocrystalline domains embedded in amorphous matrix and 5-15 nm nanocrystals with coherent grain boundary. The significantly reduced thermal conductivity leads to a state-of-the-art dimensionless figure of merit ZT{approx}1.56 at 300 K, more than 50% improvement of that of the commercial Bi{sub 2}Te{sub 3} ingot materials.

36 MATERIALS SCIENCE↗

Beneficial influence of Ru on the thermoelectric properties of Mo{sub 3}Sb{sub 7}

Zintl phases have recently been identified as potential thermoelectric materials typified by the discovery of a high thermoelectric figure of merit in the Yb{sub 14}MnSb{sub 11} compound above 1000 K. We report on the synthesis and the thermoelectric properties measurements over a wide temperature range (300-1000 K) of other Zintl phases exhibiting a complex crystalline structure, namely, Mo{sub 3}Sb{sub 7} and its related compounds Mo{sub 3-x}Ru{sub x}Sb{sub 7}. While the binary compound displays low figure of merit values due to its metallic nature, we show that the partial substitution of Mo by Ru significantly improves its value to reach 0.45 at 1000 K in Mo{sub 2.2}Ru{sub 0.8}Sb{sub 7}.

36 MATERIALS SCIENCE↗

Evaporation residue yields in reactions of heavy neutron-rich radioactive ion beams with {sup 64}Ni and {sup 96}Zr targets

As hindrance sets in for the fusion of heavier systems, the effect of large neutron excess in the colliding nuclei on their probability to fuse is still an open question. The detection of evaporation residues (ERs), however, provides indisputable evidence for the fusion (complete and incomplete) in the reaction. We therefore devised a system with which we could measure ERs using low intensity neutron-rich radioactive ion beams with an efficiency close to 100%. We report on measurements of the production of ERs in collisions of {sup 132,134}Sn, {sup 134}Te and {sup 134}Sb ion beams with medium mass, neutron-rich targets. The data taken with {sup 132,134}Sn bombarding a {sup 64}Ni target are compared to available data (ERs and fusion) taken with stable Sn isotopes. Preliminary data on the fusion of {sup 132}Sn with {sup 96}Zr target are also presented.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

High thermoelectric performance BiSbTe alloy with unique low-dimensional structure

We report a detailed description of an innovative route of a melt spinning (MS) technique combined with a subsequent spark plasma sintering process in order to obtain high performance p-type Bi{sub 0.52}Sb{sub 1.48}Te{sub 3} bulk material, which possesses a unique low-dimensional structure. The unique structure consists of an amorphous structure, 5-15 nm fine nanocrystalline regions, and coherent interfaces between the resulting nanocrystalline regions. Measurements of the thermopower, electrical conductivity, and thermal conductivity have been performed over a range of temperature of 300-400 K. We found that MS technique can give us considerable control over the resulting nanostructure with good thermal stability during the temperature range of 300-400 K and this unique structure can effectively adjust the transport of phonons and electrons, in a manner such that it is beneficial to the overall thermoelectric performance of the material, primarily a reduction in the lattice thermal conductivity. Subsequently, this results in a maximum figure of merit ZT value of 1.56 at 300 K for p-type Bi{sub 0.52}Sb{sub 1.48}Te{sub 3} bulk material. This ZT value is over a 50% improvement of that of the state of the art commercial Bi{sub 2}Te{sub 3} materials. We also report results of thermal cycling of this material for over one hundred cycles between 300-400 K. Our work offers an innovative route for developing high performance bismuth telluride based alloys and devices, which have even broader prospects for commercial applications. This technique may also be applicable to other thermoelectric materials.

36 MATERIALS SCIENCE↗

Crystallization of sputtered-deposited and ion implanted amorphous Ge{sub 2}Sb{sub 2}Te{sub 5} thin films

X-ray diffraction and transmission electron microscopy have been utilized to measure the ion irradiation-induced modification in amorphous Ge{sub 2}Sb{sub 2}Te{sub 5} thin films. The isothermal crystallization of sputtered-deposited and Sb{sup +} ion irradiated amorphous samples has been studied, focusing on the evolution of the microstructure during the initial stage of the transformation. In both samples, the amorphous to crystal transition occurs through the nucleation of face centered cubic (fcc) crystal domains at the film surface. A fast bidimensional growth of the crystalline nuclei in the sputtered-deposited films occurs by the generation of transrotational grains. The lattice parameter decreases as the crystalline fraction increases above 80%, and it approaches the fcc bulk value at the end of the transformation. Ion irradiation produces a densification of the deposited amorphous film (approx4% vertical shrinkage measured by atomic force microscopy) and an enhancement of the crystallization rate. Even in the irradiated amorphous, the nucleation occurs at the film surface and proceeds by the growth of the grains through the thickness of the layer although the density of the transrotational grains is strongly reduced with respect to the unirradiated amorphous. A link between the ion beam induced densification and the reduction of transrotational grains is proposed.

36 MATERIALS SCIENCE↗

Change in the resistivity of Ge-doped Sb phase change thin films grown by chemical vapor deposition according to their microstructures

This study examined the effects of the composition and microstructure on the electric resistivity of Ge-doped Sb phase change thin films grown by cyclic plasma enhanced chemical vapor deposition. Ge and Sb layers were deposited sequentially to form either a Ge{sub x}Sb{sub y} mixture or Ge/Sb nanolaminated films. While the resistivity of the nanolaminated films was higher, the Ge{sub x}Sb{sub y} mixture showed a lower resistivity than the pure Sb film. This can be explained by the increase in carrier density of the alloy, as confirmed by first-principles calculations. An abrupt change in resistance accompanying a phase change was observed at {approx}210 deg. C.

36 MATERIALS SCIENCE↗

Thermoelectric transport properties of highly oriented FeSb{sub 2} thin films

Highly textured FeSb{sub 2} films were produced on quartz wafers by a sputtering method. Their resistivity and Seebeck coefficient (S) were measured and a maximum absolute value of Sapprox160 muV K{sup -1} at 50 K was obtained. Hall measurements were employed to study the charge carrier concentrations and Hall mobilities of the FeSb{sub 2} films. By comparing with the transport properties of FeSb{sub 2} single crystals and an extrinsically doped FeSb{sub 1.98}Te{sub 0.02} single crystal, the thermoelectric properties of the FeSb{sub 2} films are demonstrated to be dominated by the intrinsic properties of FeSb{sub 2} at a high charge carrier concentration.

36 MATERIALS SCIENCE↗

Analysis of the electric field induced elemental separation of Ge{sub 2}Sb{sub 2}Te{sub 5} by transmission electron microscopy

The chemical instability of line patterned Ge{sub 2}Sb{sub 2}Te{sub 5} was studied by transmission electron microscopy after electrically inducing melt and solidification. Compositional analysis showed elemental separation of Te to the anode side, while Ge and Sb mutually separated at the cathode side. Such elemental separation of Ge{sub 2}Sb{sub 2}Te{sub 5} is explained by the electric field effects and thermodynamic driving forces.

36 MATERIALS SCIENCE↗

Atomic migration in molten and crystalline Ge{sub 2}Sb{sub 2}Te{sub 5} under high electric field

Atomic migration under an electric field, electromigration, in molten and crystalline Ge{sub 2}Sb{sub 2}Te{sub 5} was studied using a pulsed dc stress to an isolated line structure. Under a single pulse ({approx}10{sup -3} s), Ge{sub 2}Sb{sub 2}Te{sub 5} was melted by Joule heating, and an electrostatic force-induced drift of Ge and Sb toward the cathode and Te toward the anode was observed. Effective charge numbers were calculated to be 0.28, 0.38, and -0.29 for Ge, Sb, and Te, respectively. Electromigration in the crystalline state was studied by applying a 10 MHz pulsed dc; constituent elements migrated toward the cathode, which suggests a hole wind-force operating in this phase.

36 MATERIALS SCIENCE↗

Electronic structure of (Ge{sub 2}Sb{sub 2}Te{sub 5}){sub 1-x}(In{sub 3}SbTe{sub 2}){sub x} investigated by x-ray photoelectron spectroscopy

We have investigated the core levels and the valence band of (Ge{sub 2}Sb{sub 2}Te{sub 5}){sub 1-x}(In{sub 3}Sb{sub 1}Te{sub 2}){sub x} quaternary phase system (IGST) by means of x-ray photoelectron spectroscopy. A systematic shift of Sb 3d and Ge 2p core-level peaks toward lower binding energies side was observed with increasing indium amount, whereas the In 3d and Te 3d core peaks showed less change. The Sb 3d and Ge 2p core-level shift is attributed to an increase in the electronic charge of p-electrons dependent of indium amount. The valence band spectra show a distinct change in the sp configuration with indium concentration change. The change in the local bonding as the indium amount increase has a profound impact on both local atomic arrangement and amorphous-to-crystalline transformation temperature. The difference in the photoemission spectra have been discussed according to a simple structural model suggesting that the Na site in IGST can be occupied by Te, Sb, In, and vacancy, whereas in GST it is occupied only by Te.

36 MATERIALS SCIENCE↗

Unambiguous determination of carrier concentration and mobility for InAs/GaSb superlattice photodiode optimization

In this communication we report on electrical properties of nonintentionally doped (nid) type II InAs/GaSb superlattice grown by molecular beam epitaxy. We present a simple technological process which, thanks to the suppression of substrate, allows direct Hall measurement on superlattice structures grown on conductive GaSb substrate. Two samples were used to characterize the transport: one grown on a semi-insulating GaAs substrate and another grown on n-GaSb substrate where a etch stop layer was inserted to remove the conductive substrate. Mobilities and carrier concentrations have been measured as a function of temperature (77-300 K), and compared with capacitance-voltage characteristic at 80 K of a photodiode comprising a similar nid superlattice.

36 MATERIALS SCIENCE↗

Investigation on the role of nitrogen in crystallization of Sb-rich phase change materials

To better understand the role of nitrogen (N) during crystallization of Sb-rich phase change materials, a study was conducted using Sb and Sb{sub 70}Te{sub 30} as host materials of N. Crystallization of the as-sputtered Sb-N films of varying N content was examined to reveal that Sb-N bonds are formed in the as-sputtered states, enhancing amorphous phase stability increasingly with N content. Crystallization appeared to proceed with irreversible dissociation of these bonds to form N{sub 2} molecules that may then exist stably during the subsequent memory operations. N{sub 2} molecules are considered to play as growth-retarding agents as demonstrated with memory operations of N-doped Sb{sub 70}Te{sub 30}.

36 MATERIALS SCIENCE↗

Fast phase transition process of Ge{sub 2}Sb{sub 2}Te{sub 5} film induced by picosecond laser pulses with identical fluences

Fast phase transition processes on Ge{sub 2}Sb{sub 2}Te{sub 5} film induced by picosecond laser pulses were studied using time-resolved reflectivity measurements. It was found that after picosecond laser pulse priming, reversible switching could be occurred upon picosecond laser pulse irradiation with the same well-chosen fluence. This is very different from general knowledge that reversible phase change process will be induced by laser pulses with different powers; that is, amorphization process needs much higher fluence than crystallization process. The possible mechanism was discussed qualitatively by a melting-cooling model.

36 MATERIALS SCIENCE↗

Dynamic in situ observations of electrical and structural changes in thin thermoelectric (Bi{sub 0.15}Sb{sub 0.85}){sub 2}Te{sub 3} films

Thin films of (Bi{sub 0.15}Sb{sub 0.85}){sub 2}Te{sub 3} were prepared by dc magnetron sputter deposition on different substrates. It is well known that thermal treatment of as-deposited p-type (Bi{sub 0.15}Sb{sub 0.85}){sub 2}Te{sub 3} films leads to an enhancement of the power factor. Whereas up to now only the initial (as deposited) and the final (after annealing) film stages have been investigated, here, the dynamic changes of sputter-deposited film properties have been observed by in situ measurements. The enhancement of the power factor shows a significant dependence on thermal treatment. The best thermoelectric films have been prepared at a substrate temperature of 170 deg. C, with a power factor of 24.4 muW/(cm K{sup 2}). The changes in the Seebeck and Hall coefficients are caused by the enhancement in the Hall mobility after annealing. In situ x-ray diffractometry shows the generation of additional Te in dependence of the temperature. This is also confirmed by energy-dispersive x-ray microanalysis and the corresponding mapping in a scanning electron microscope. It is supposed that the locally well-defined Te enrichment is the reason for the improvement in the integral film transport properties.

36 MATERIALS SCIENCE↗

Interfacial intermixing in InAs/GaSb short-period-superlattices grown by molecular beam epitaxy

The unique properties of the noncommon-atom InAs/GaSb short-period-superlattices (SPSL) strongly depend on the interface structure. These interfaces are characterized using transmission electron microscopy (TEM). The compositional sharpness is obtained from the comparison of the experimental contrast in g{sub 002} two-beam dark-field TEM images with simulated intensity profiles, which are calculated assuming that the element distribution profiles are described by sigmoidal functions. The interfacial intermixing, defined by the chemical width, is obtained for SPSL with different periods and layer thicknesses, even in the extreme case of nominally less than 3 ML thick InAs layers. Nominal 1 ML InSb layers intentionally inserted are also identified.

36 MATERIALS SCIENCE↗

Interband transitions in strained InGaAs/AlAsSb multiple-quantum-well structures

Room temperature photoreflectance (PR) was performed on strained In{sub x}Ga{sub 1-x}As/AlAsSb quantum wells (QWs) grown on InP substrates. We observed clear and well-resolved structures, which could be attributed to the interband optical transitions originating in the QWs. By comparing the transition energies measured from the PR spectra with those theoretically calculated from the confined energy levels in the QWs, we confirmed that the value of the conduction band offset of In{sub 0.8}Ga{sub 0.2}As/AlAsSb was close to 1.7 eV and the nonparabolicity of the conduction band of In{sub 0.8}Ga{sub 0.2}As was between 2.25 and 2.5, which is higher than that obtained using a three-band model.

36 MATERIALS SCIENCE↗