Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ADVANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

SULI Internship Deliverables (Flow Orifice Design: Measuring Degas Flow of Experiment Loops at the Advanced Test Reactor)

These deliverables present a design for a new orifice flow meter to be installed in three experiment loops at the Advanced Test Reactor. The current configuration of the experiment loop system has an orifice that is not properly sized to the low flow rates of the degas line of the pressurizer system, causing inaccurate flow measurements. Under consideration of flow conditions and system constraints, an iterative procedure was utilized to determine the optimal sizing for a new orifice. This orifice is designed to accurately and precisely measure the flow rate of the degas line, which will consequently improve control of the pressure and chemistry of the loop pressurizer system. The scope of this project includes recommendations for orifice sizing, material, flange type, face type, and installation location on the loop piping spools. The design is suitable for experiment loops 1D-N, 2B-SE, and 2D-SW and meets all necessary standards.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Options for Achieving Cost Reduction in Advanced Reactors through Open Architecture

A key contributor to high capital costs and schedule overruns for new nuclear power plants is lack of standardization, driven by site-specific customization and construction of multiple designs by competing vendors rather than commitment to a single standardized program. While advanced reactor vendors typically individually target repeat construction of standardized units, the many competing designs could exacerbate the problem. “Open Architecture”, the open specification of requirements and interfaces for structures, systems and components (SSCs), has been proposed as a means of promoting standardization, by facilitating existing non-nuclear suppliers to enter the industry and/or allowing SSCs to be configured for more than one reactor within the same technology type. Contracting mechanisms that facilitate information sharing and alignment of incentives between stakeholders may complement such an approach. A preliminary scheme is presented for selection of SSCs for which such strategies could be adopted, based on a vendor make/buy decision model and stakeholder interviews. SSCs are categorized according to number of suppliers and their contribution to the reactor’s competitive edge. SSCs with many potential suppliers and a high contribution to competitive edge may be attractive for widening the supply chain via open specification of system requirements and interfaces, e.g., SSCs in the power island. SSCs with few suppliers and low contribution to competitive edge may be potential avenues for common system specification between vendors, e.g., some of the auxiliary SSCs. Potential cost reductions from such strategies will depend upon the size of the build program and the reactor type.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Advanced Test Reactor Experiment Safety Analysis

This presentation contains general information about the Advanced Test Reactor experiment safety analysis program. Accidents and dose consequence are discussed in general terms. Pictures of ATR facilities and experiments are included. In cases where experiments are shown, identification numbers have been removed. Department of Energy limits on dose consequence are provided. These limits are found in many non-CUI documents and a derived from publicly available sources. A summary of the presentation content is as follows: -Define Experiment Safety Analysis -Discuss what we are protecting and the applicable limits -Show how safety analysis fits into the experiment process -Explore the scope of experiment activities and associated accidents -Present how we categorize accidents and establish accident frequencies -Identify how controls are implemented and process improvements

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Workshop: Advanced Metering for Decarbonization: Electric Vehicles and 24/7 Carbon-Free Electricity

The purpose of this workshop is to learn more about advanced metering best practices for meeting the goals of EO 14057. This will be a 2-part session, first part to include presentations on the FEMP best practice work related to metering: 1) Electric Vehicles (EVs) and EV charging station electricity use. 2) Integrating data sources to calculate hourly carbon pollution-free electricity (CFE). Second part will facilitate small group discussions with a problem-solving activity.

ADVANCED PROPULSION SYSTEMS,ENERGY PLANNING, POLIC↗
DOE OSTI2023

Completion of Nuclear Testing after Core Internals Changeout #6 in the Advanced Test Reactor

A series of physics tests were conducted in 2022 for the Advanced Test Reactor (ATR) after the sixth Core Internals Changeout (CIC) in 2021. These tests verify nuclear characteristics of the new reflector and shim mechanisms and are validation cases for core models. This work describes the results of these tests and compares the physics tests with those performed previously in ATR and updates previous work reporting on planning for nuclear testing and on preliminary results of several low-power tests. This work also identifies unique characteristics of ATR that result in the need for unique tests.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Replacement of Legacy Analytical Codes at the Advanced Test Reactor

For each operating cycle of the Advanced Test Reactor (ATR) at Idaho National Laboratory, a Core Safety Assurance Package (CSAP) is necessary to demonstrate compliance with the safety basis approved by the United State Department of Energy (DOE). Certain computer codes are used in CSAP development, most of them developed in-house. This work describes replacement of a large set of these codes and updates previous work. Replacement of legacy codes is necessary due to computer hardware failure but also has generally improved user-friendliness.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Scoping Study of Effects on the Advanced Test Reactor’s Center Flux Trap Due to Various Loadings in the H and Inner A Test Positions

This study determined the effects experienced by the In-Pile Tube, of the Advanced Test Reactor’s center flux trap, due to various loading configurations of the H and Inner A positions. The effects of concern included: the axial profile of the linear heat generation rate of each fuel rodlet, the axial flux shape, and spectrum, in the fuel, and cladding, of each rodlet, and the total fission heating rate of the entire In-Pile Tube. Additionally, the reactivity worth of each configuration, relative to an ATR configuration with water filling all concerning test positions, was determined. The test positions were filled with commonly used test specimens, backup test specimens, and homogeneous substances. The study was performed using the modeling software MCNP6.2.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Evaluation of Nickel Alloys, Manufactured through Powder Bed Fusion, for Application for Advanced Nuclear Reactors

In collaboration with other laboratories, Idaho National Laboratory has investigated additively manufactured alloys for applications in advanced nuclear reactors. The primary focus has been on nickel alloys, as well as “other” alloys, which are alloys not considered steel nor nickel-based alloys, manufactured by laser powder bed fusion. Suitability of investigated alloys were considered against a matrix of properties of interest, developed jointly with the collaborating laboratories. For the nickel alloys, Alloys 282 and 625 are considered promising due to their properties, existing data, and availability of commercial powder feedstock. Haynes 244 is also of interest for its molten salt corrosion resistance, however there is no current feedstock supply chain, and no experience with this alloy as an additively manufactured material. Iron-chrome-aluminum alloys, titanium alloys, zirconium alloys, ceramics, and ceramic inclusions were all considered within the other alloys category. The results and discussions within this report will be compiled with the investigations from the other collaborating laboratories and compiled into a final report later this year (2023).

36 MATERIALS SCIENCE↗
DOE OSTI2023

Replacement of Legacy Analytical Codes at the Advanced Test Reactor

For each operating cycle of the Advanced Test Reactor (ATR) at Idaho National Laboratory, a Core Safety Assurance Package (CSAP) is necessary to demonstrate compliance with the safety basis approved by the United State Department of Energy (DOE). Certain computer codes are used in CSAP development, most of them developed in-house. This work describes replacement of a large set of these codes and updates previous work. Replacement of legacy codes is necessary due to computer hardware failure but also has generally improved user-friendliness.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Advancing Affordable, Efficient, and Clean Transportation

Clean Cities and Communities is a U.S. Department of Energy (DOE) partnership to advance clean transportation nationwide. More than 75 DOE-designated Clean Cities and Communities coalitions work locally in urban, suburban, and rural communities to strengthen the nation's environment, energy security, and economic prosperity. As partners with DOE's Vehicle Technologies Office (VTO), coalitions work to deploy affordable, efficient, and clean transportation; energy efficient mobility systems; and fuel-saving technologies and practices.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

EVALS: Enhanced VALidation of Advanced Battery Supply Chains

This is an overview of EVALS (Enhanced VALidation of advanced battery Supply chains), funded by the U.S. Department of Energy Vehicle Technologies Office (VTO) and some initial data from a transformational laboratory directed research and development (LDRD) program project funded at NREL. EVALS aims to accelerate the process to bring domestic and allied primary sources of battery materials online, from production to deployment.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Evaluation of an Accident Tolerant Fuel Leak in the Advanced Test Reactor

Accident Tolerant Fuels (ATF), which are nuclear fuel sources designed to withstand operational irregularities and incidents, have been a topic of interest in the nuclear industry for several decades. Interest in ATF technology surged following the 2011 accident at Fukushima Daiichi in Japan. At the Advanced Test Reactor (ATR), one of Idaho National Laboratory’s (INL) four operating nuclear reactors, the ATF program is a collaborative effort between the national laboratory and various stakeholders within the nuclear industry. This program focuses on the research and development of novel fuel compositions, cladding, and component materials with enhanced accident-resistant properties. During one of ATR’s 60-day operating cycles in 2024, the reactor experienced five unplanned shutdowns. Following the fifth shutdown, radiation monitors detected an increase in radiation levels coming from the loop piping. Subsequent water samples confirmed the cause was a leak of fission products from the ATF experiment, designated as ATF-2C. The source of the leak was identified as the instrumented section of the test train. The primary discussions in this paper are 1) the design of the ATF test train, 2) the operating parameters leading up to and following the detection of the leak, and 3) the quantification and characterization of the released fission products.

Accident Tolerant Fuels↗