Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ACTIVATION ENERGY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Electrical properties of Ba(Dy{sub 1/2}Nb{sub 1/2})O{sub 3} ceramic

Polycrystalline Ba(Dy{sub 1/2}Nb{sub 1/2})O{sub 3} was prepared using a high-temperature solid-state reaction method. X-ray diffraction analysis indicated the formation of a single-phase cubic structure having space group Pm3m. AC impedance plots as a function of frequency at different temperatures were used to analyse the electrical behaviour of the sample, which indicated the negative temperature coefficient of resistance character. Complex impedance analysis targeted non-Debye type dielectric relaxation. Frequency dependent ac conductivity data obeyed Jonscher’s power law. The apparent activation energy was estimated to be 0.97 eV at 1 kHz.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Room temperature ammonia and VOC sensing properties of CuO nanorods

Here, we report a NH{sub 3} and Volatile Organic Compounds (VOCs) sensing prototype of CuO nanorods with peculiar sensing characteristics at room temperature. High quality polycrystalline nanorods were synthesized by a low temperature hydrothermal method. The rods are well oriented with an aspect ratio of 5.71. Luminescence spectrum of CuO nanorods exhibited a strong UV-emission around 415 nm (2.98 eV) which arises from the electron-hole recombination phenomenon. The absence of further deep level emissions establishes the lack of defects such as oxygen vacancies and Cu interstitials. At room temperature, the sensor response was recorded over a range of gas concentrations from 100-600 ppm of ammonia, ethanol and methanol. The sensor response showed power law dependence with the gas concentration. This low temperature sensing can be validated by the lower value of calculated activation energy of 1.65 eV observed from the temperature dependent conductivity measurement.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Proton Conductivity and Thermal Properties of Ba(H{sub 2}PO{sub 4}){sub 2}

We have grown single crystals of barium dihydrogen phosphate and studied its thermal transformations during heating to 500°C and its electrotransport properties. Ba(H{sub 2}PO{sub 4}){sub 2} (Pccn) has been shown to undergo no phase transitions up to its dehydration temperature. The thermal decomposition of Ba(H{sub 2}PO{sub 4}){sub 2}, accompanied by dehydration, involves two steps, with maximum rates at ~265 and 370°C, and results in the formation of barium dihydrogen pyrophosphate and barium metaphosphate, respectively. The total enthalpy of the endothermic dehydration events is–244.6 J/g. Using impedance spectroscopy, we have studied in detail the proton conductivity of polycrystalline and single-crystal Ba(H{sub 2}PO{sub 4}){sub 2} samples in a controlled atmosphere. Adsorbed water has been shown to have a significant effect on the proton conductivity of Ba(H{sub 2}PO{sub 4}){sub 2} up to 130°C. The proton conductivity of the Ba(H{sub 2}PO{sub 4}){sub 2} single crystals has been shown to be anisotropic. The conductivity anisotropy correlates with specific structural features of the salt. Higher conductivity values, 3 × 10{sup –9} to 2 × 10{sup –7} S/cm in the range 60–160°C, have been observed in the [100] crystallographic direction, exceeding the conductivity along [010] by an order of magnitude. The activation energy for proton conduction is 0.80 eV.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Energy levels distribution in supersaturated silicon with titanium for photovoltaic applications

In the attempt to form an intermediate band in the bandgap of silicon substrates to give it the capability to absorb infrared radiation, we studied the deep levels in supersaturated silicon with titanium. The technique used to characterize the energy levels was the thermal admittance spectroscopy. Our experimental results showed that in samples with titanium concentration just under Mott limit there was a relationship among the activation energy value and the capture cross section value. This relationship obeys to the well known Meyer-Neldel rule, which typically appears in processes involving multiple excitations, like carrier capture/emission in deep levels, and it is generally observed in disordered systems. The obtained characteristic Meyer-Neldel parameters were Tmn = 176 K and kTmn = 15 meV. The energy value could be associated to the typical energy of the phonons in the substrate. The almost perfect adjust of all experimental data to the same straight line provides further evidence of the validity of the Meyer Neldel rule, and may contribute to obtain a deeper insight on the ultimate meaning of this phenomenon.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

European activities in the hydrogen energy field

Research activities in the hydrogen energy field in the European community are reviewed. Countries included in the discussion are: Austria, Belgium, England, Federal Republic of Germany, and Italy.

Chirivella, J. E.↗

Arylammonium-Assisted Reduction of the Open-Circuit Voltage Deficit in Wide-Bandgap Perovskite Solar Cells: The Role of Suppressed Ion Migration

Surface treatment using large alkyl/aryl ammonium cations has demonstrated reduced open-circuit voltage (V OC ) deficits in perovskite solar cells (PSCs), but the origin of the improvements has been vaguely attributed to defect passivation. Here, we combine the microscopic probing of the local electrical properties, thermal admittance spectroscopic analysis, and first principles calculations to elucidate the critical role of arylammonium interface layers on suppressing the ion migration in wide-bandgap (WBG) PSCs. Our results reveal that arylammonium surface treatment using phenethylammonium iodide increases the activation energy barrier for ion migration on the surface, which suppresses the accumulation of charge defects at surface and grain boundaries (GBs), leading to reduced dark saturation current density in WBG PSCs. Furthermore, with device optimization, our champion 1.73-eV PSC delivers a power conversion efficiency of 19.07% with a V OC of 1.25 V, achieving a V OC -deficit of 0.48 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of Si/Al Ratio on the Distribution of Framework Al and on the Rates of Alkane Monomolecular Cracking and Dehydrogenation in H-MFI

For this study, the aim was to investigate the influence of Si/Al ratio on the locations of exchangeable cations in H-MFI and on the monomolecular cracking and dehydrogenation reactions of n -butane. On the basis of UV-visible spectroscopic analysis of Co(II) exchanged into MFI, it was inferred that the fraction of Co(II) (and, by extension, Brønsted protons) located at channel intersections relative to straight and sinusoidal channels increases with increasing Al content. Concurrently, turnover frequencies for all monomolecular reactions, and the selectivities to dehydrogenation versus cracking and to terminal cracking versus central cracking, generally increased. The changes in selectivity with Al content are consistent with the finding that the transition-state geometry for dehydrogenation is bulky and resembles a product state, and should therefore exhibit a stronger preference to occur at channel intersections relative to cracking. Increases in turnover frequencies are attributed partly to increases in intrinsic activation entropies that compensate for concurrent increases in intrinsic activation energies, most strongly for dehydrogenation and terminal cracking, resulting in increased selectivity to these reactions at higher Al content. This interpretation contrasts with the view that intrinsic activation barriers are constant. It is also observed that isobutene inhibits the rate of n-butane dehydrogenation. Theoretical calculations indicate that this effect originates from adsorption of isobutene at the channel intersections. Because cracking reaction rates are not affected by the presence of isobutene, this result suggests that the preference of dehydrogenation to occur at channel intersections is much stronger than the preference for cracking to occur at these locations.

activation energy↗

Deformation of the surface of gallium arsenide during the deposition of gold

Deformation phenomena of near-surface GaAs layers are studied using surface acoustic waves during the deposition of Au and the irradiation of the semiconductor surface by the light of a heated evaporator. It is shown that, in the case of Au deposition, the near-surface layers are plasticized due to the phase transformations in the Au-Ga-As system, while upon irradiation of the GaAs surface with light, a coarse-grained layer with liquid-like interlayers is formed. As a result, the type of surface deformations and their relaxation time change. The integral temporal characteristics of the surface acoustic wave, such as the variation integrals of its rate and dissipated power, reflect the processes occurring on the surface in the real-time mode. In summary, they reflect the current magnitude of the resulting deformation. The parameters of occurring processes such as activation energy and relaxation time are determined.

36 MATERIALS SCIENCE↗

Impedance Spectroscopy Study of the Electrical Properties of Cation-Substituted Barium Hexaaluminate Ceramics

We report on the behavior of frequency and temperature dependences of the impedance of a measuring cell in the form of a parallel-plate capacitor filled with barium hexaaluminate ceramics with four aluminum cations replaced by iron (BaO · 2Fe{sub 2}O{sub 3} · 4Al{sub 2}O{sub 3}). The measurements have been performed in the frequency range of 0.5–10{sup 8} Hz at temperatures of 20-375°C. A technique for determining the electrical properties of the investigated ceramics is proposed, which is based on an equivalent electric circuit allowing the recorded impedance spectra to be approximated with sufficiently high accuracy. The established spectral features are indicative of the presence of two electric relaxation times different from each other by three orders of magnitude. This fact is explained by the difference between the charge transport processes in the bulk of crystallites and thin intercrystallite spacers, for which the charge activation energies have been determined.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Formation and annihilation of E4 centers in ZnO: Influence of hydrogen

Hydrothermally grown n-type ZnO bulk samples have been implanted with protons and deuterium ions to fluences in the range of 8 × 10{sup 10} to 8 × 10{sup 11 }cm{sup −2}. The implantations were performed at the temperature of 285 K, and the samples were then analyzed in-situ by deep level transient spectroscopy (DLTS) using a setup connected to the implanter beam line. The concentration of the so-called E4 center, having an apparent energy level at ∼0.57 eV below the conduction edge, is found to increase linearly with the ion fluence and the generation rate is proportional to the elastic energy deposition, as expected for a primary defect. Isothermal annealing of the E4 center at temperatures between 290 and 315 K reveals first-order kinetics with the activation energy of ∼0.6 eV. The annealing rate is strongly enhanced with increasing hydrogen fluence, and a model invoking migration of interstitial hydrogen and subsequent reaction with E4 exhibits close agreement with the experimental data. The rate of electron capture by E4 during the DLTS filling pulse depends on temperature, and it displays a thermal barrier of ∼0.15 eV. Most of these experimental results for E4 conform to the theoretically predicted properties of the oxygen vacancy (V{sub O}) and a tentative assignment of E4 to V{sub O} is made, corroborating previous suggestions in the literature. In particular, the 0.57 eV level is ascribed to the double donor state of V{sub O}.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Analysis of defects in GaAsN grown by chemical beam epitaxy on high index GaAs substrates

The lattice defects in GaAsN grown by chemical beam epitaxy on GaAs 311B and GaAs 10A toward [110] were characterized and discussed by using deep level transient spectroscopy (DLTS) and on the basis of temperature dependence of the junction capacitances (C{sub J}). In one hand, GaAsN films grown on GaAs 311B and GaAs 10A showed n-type and p-type conductivities, respectively although the similar and simultaneous growth conditions. This result is indeed in contrast to the common known effect of N concentration on the type of conductivity, since the surface 311B showed a significant improvement in the incorporation of N. Furthermore, the temperature dependence of C{sub J} has shown that GaAs 311B limits the formation of N-H defects. In the other hand, the energy states in the forbidden gap of GaAsN were obtained. Six electron traps, E1 to E6, were observed in the DLTS spectrum of GaAsN grown on GaAs 311B, with apparent activation energies of 0.02, 0.14, 0.16, 0.33, 0.48, and 0.74 eV below the bottom edge of the conduction band, respectively. In addition, four hole traps, H1 to H4, were observed in the DLTS spectrum of GaAsN grown on GaAs 10A, with energy depths of 0.13, 0.20, 0.39, and 0.52 eV above the valence band maximum of the alloy, respectively. Hence, the surface morphology of the GaAs substrate was found to play a key factor role in clarifying the electrical properties of GaAsN grown by CBE.

36 MATERIALS SCIENCE↗

Photo-instability of CdSe/ZnS quantum dots in poly(methylmethacrylate) film

The photo-instability of CdSe/ZnS quantum dots (QDs) has been studied under varied conditions. We discussed the main features of the evolution of photoluminescence (PL) intensity and energy at different laser powers, which showed critical dependences on the environment. The PL red shift in a vacuum showed strong temperature dependence, from which we concluded that the thermal activation energy for trapping states of the charge carriers was about 14.7 meV. Furthermore, the PL spectra showed asymmetric evolution during the laser irradiation, for which two possible explanations were discussed. Those results provided a comprehensive picture for the photo-instability of the colloidal QDs under different conditions.

36 MATERIALS SCIENCE↗

Aging Effect Analysis of PV Inverter Semiconductors for Ancillary Services Support

PV inverters can provide reactive power while generating active power. An ongoing microgrid implementation at Duke Energy actively engages non-utility PVs to generate/absorb reactive power in support of ancillary services to increase microgrid resiliency during extreme events. PV systems are requested to provide reactive power support: 1) in response to grid voltage variation to better regulate the local voltage; or 2) in response to utility incentives, such as following Transactive Energy System (TES) incentives. However, providing ancillary services might shorten the lifetime expectation of PV inverter semiconductors. This paper summarizes the potential impacts on a PV inverter semiconductor's lifetime when providing ancillary services. The analysis presented in this research work shows that providing reactive power support will increase the mean junction temperature and the junction temperature variation of the inverter diodes. This increased junction temperature will eventually lead to shorter diode lifetime. The lifetime estimation of semiconductors is briefly reviewed. The power losses of PV inverter semiconductors are derived as a support analysis to the junction temperature calculation. In addition, the impact of the filtering inductor on the semiconductor current distribution is discussed. The theoretical analysis presented in this research work is supported by simulation results.

14 SOLAR ENERGY↗

The Role of Organic Capping Layers of Platinum Nanoparticles in Catalytic Activity of CO Oxidation

We report the catalytic activity of colloid platinum nanoparticles synthesized with different organic capping layers. On the molecular scale, the porous organic layers have open spaces that permit the reactant and product molecules to reach the metal surface. We carried out CO oxidation on several platinum nanoparticle systems capped with various organic molecules to investigate the role of the capping agent on catalytic activity. Platinum colloid nanoparticles with four types of capping layer have been used: TTAB (Tetradecyltrimethylammonium Bromide), HDA (hexadecylamine), HDT (hexadecylthiol), and PVP (poly(vinylpyrrolidone)). The reactivity of the Pt nanoparticles varied by 30%, with higher activity on TTAB coated nanoparticles and lower activity on HDT, while the activation energy remained between 27-28 kcal/mol. In separate experiments, the organic capping layers were partially removed using ultraviolet light-ozone generation techniques, which resulted in increased catalytic activity due to the removal of some of the organic layers. These results indicate that the nature of chemical bonding between organic capping layers and nanoparticle surfaces plays a role in determining the catalytic activity of platinum colloid nanoparticles for carbon monoxide oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dielectric strength and reliability of ferroelectric PLZT films deposited on nickel substrates.

We have deposited ferroelectric (FE) Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} (PLZT) films on nickel substrates by chemical solution deposition. Energy density of {approx} 46 J/cm{sup 3} has been measured with 1.15-{micro}m-thick PLZT/LNO/Ni film-on-foil capacitors. A series of highly accelerated lifetime tests were performed to determine the reliability of these FE film-on-foil capacitors under high temperature and high field stress. Samples were exposed to temperatures ranging from 100 to 150 C and electric fields ranging from 8.7 x 10{sup 5} V/cm to 1.3 x 10{sup 6} V/cm. The breakdown behavior of the FE PLZT film-on-foil capacitors was evaluated by Weibull analysis. The activation energy was determined to be {approx} 0.35 eV when an electric field of 1.05 x 10{sup 6} V/cm was applied. The voltage acceleration factor was {approx} -6.3 at 100 C. The mean time to failure was projected to be > 3000 h at 100 C with a dc electric field of {approx} 2.6 x 10{sup 5} V/cm.

25 ENERGY STORAGE↗

Diffusion of Magnesium in Led Structures with InGaN/GaN Quantum Wells at True Growth Temperatures 860–980°C of p-GaN

The results of an investigation of Mg diffusion in blue LED structures with InGaN/GaN quantum wells are presented for various growth temperatures of the p-GaN layer. The values of the diffusion coefficient estimated for true growth temperatures of 860, 910, and 980°C were 7.5·10{sup –17}, 2.8·10{sup –16}, and 1.2·10{sup –15} cm{sup 2}/s, respectively. The temperature values given in the work were measured on the surface of the growing layer in situ using a pyrometer. The calculated activation energy for the temperature dependence of the diffusion coefficient was 2.8 eV.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Growth and electrical properties on NLO crystal: 4-N,N-dimethylamino 4′-N′-methylstilbazolium iodide

4-N,N-Dimethylamino-4′-N′-methylstilbazolium tosylate single crystals were grown by solution crystal growth method. The cell parameters of grown crystal have been estimated using single crystal-X-ray diffraction analysis. The variation of real (´ε) and imaginary (´ε) part of dielectric constants and dielectric loss were observed for different frequencies and temperatures. The ac and dc electrical conductivities and activation energy were determined for DMSI crystal using dielectric studies.

36 MATERIALS SCIENCE↗

Sodium diffusion in 4H-SiC

Sodium diffusion has been studied in p-type 4H-SiC. Heat treatments have been performed from 1200 °C to 1800 °C for 1 min to 4 h. Secondary ion mass spectrometry has been used to measure the sodium distribution. We show that sodium has a considerable mobility at 1200 °C in p-type 4H-SiC. On the other hand for sodium atoms trapped at suitable sites the mobility is limited up to 1800 °C. Trap limited diffusion kinetics is suggested and an effective diffusivity has been extracted with an activation energy of 4 eV for sodium diffusion in p-type 4H-SiC.

36 MATERIALS SCIENCE↗