Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “volume distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Elemental composition and size distribution of particulates in Cleveland, Ohio

Measurements have been made of the elemental particle size distribution at five contrasting urban environments with different source-type distributions in Cleveland, Ohio. Air quality conditions ranged from normal to air pollution alert levels. A parallel network of high-volume cascade impactors (5-stage) were used for simultaneous sampling on glass fiber surfaces for mass determinations and on Whatman-41 surfaces for elemental analysis by neutron activation for 25 elements. The elemental data are assessed in terms of distribution functions and interrelationships and are compared between locations as a function of resultant wind direction in an attempt to relate the findings to sources.

Leibecki, H. F.↗
NASA NTRS1932

The Effect of Clearance Distribution on the Performance of a Compression-ignition Engine with a Precombustion Chamber

The clearance distribution in a precombustion chamber cylinder head was varied so that for a constant compression ratio of 13.5 the spherical auxiliary chambers contained 20, 35, 50, and 70 per cent of the total clearance volume. Each chamber was connected to the cylinder by a single circular passage, flared at both ends, and of a cross-sectional area proportional to the chamber volume, thereby giving the same calculated air-flow velocity through each passage. Results of engine-performance tests are presented with variations of power, fuel consumption, explosion pressure, rate of pressure rise, ignition lag, heat loss to the cooling water, and motoring characteristics. For good performance the minimum auxiliary chamber volume, with the cylinder head design used, was 35 per cent of the total clearance volume; for larger volumes the performance improves but slightly. With the auxiliary chamber that contained 35 percent of the clearance volume there were obtained the lowest explosion pressures, medium rates of pressure rise, and slightly less than the maximum power. For all clearance distributions an increase in engine speed decreased the ignition lag in seconds and increased the rate of pressure rise.

Moore, C. S.↗
NASA NTRS1984

Numerical analysis of flow and heat transfer in the VAFB LOX storage Dewar tank

The present report describes numerical simulation of three-dimensional transient distributions of velocity and temperature of liquid oxygen (LOX) in the LOX Dewar tank of Vendenberg Air Force Base (VAFB). The present analyses cover the replenish time period only. Four test cases have been considered. For all four cases, the input boundary conditions are comprised of LOX facility heat loads, drain flow rates, recirculation flow rates and dewar heating. All the quantities are prescribed as functions of time. The first two test cases considered sensitivity of results to the computational grid. In Case 3, system heat load was changed, while in Case 4, a lower LOX level was specified. Cases 1 and 2 showed that the temperatures were not sensitive to the grid refinement. This provided a basic check on the numerical model. Cases 3 and 4 showed that the thermal boundary layer motion near the tank surface becomes more significant at the late time, e.g., 5 1/2 hours from replenish start. Comparison between results of Cases 3 and 4 showed, as expected, that the smaller initial LOX volume given in Case 4, results in higher temperature level. All calculated velocity and temperature distributions were found to be plausible.

Tam, L. T.↗
DOE OSTI2026

Distributed Quantum-Enhanced Optimization: A Topographical Preconditioning Approach for High-Dimensional Search

Optimization problems become fundamentally challenging as the number of variables increases. Because the volume of the search space grows exponentially, classical algorithms frequently fail to locate the global minimum of non-convex functions. While quantum optimization offers a potential alternative, mapping continuous problems onto near-term quantum hardware introduces severe scaling limits and barren plateaus. To bridge this gap, we propose the Distributed Quantum-Enhanced Optimization (D-QEO) framework. Instead of forcing the quantum processor to find the exact minimum, we use it simply as a topographical preconditioner. The QPU maps the landscape to locate the most promising basin of attraction, generating high-quality seed points for a classical GPU-accelerated solver to refine. To make this approach viable for utility-scale problems, we exploit the mathematical structure of separable functions. This allows us to cut a 50-qubit (i.e., $2^{50}$) global search space into independent and manageable sub-spaces using 5-qubit subcircuits. By executing these fragments concurrently with CUDA-Q, we completely bypass the overhead of cross-register entanglement and classical tensor knitting for separable functions. Benchmarks on the 10-dimensional Rastrigin and Ackley functions show that D-QEO prevents the exponential failure rates observed in purely classical algorithms. Furthermore, this quantum warm-start significantly reduces the number of classical BFGS iterations required to converge, providing a highly practical blueprint for utilizing near-term quantum resources in complex global search.

Soos, Dominik [Old Dominion U.]↗
NASA NTRS1993

Accuracy of the Generalized Self-Consistent Method in Modelling the Elastic Behaviour of Periodic Composites

Local stress and strain fields in the unit cell of an infinite, two-dimensional, periodic fibrous lattice have been determined by an integral equation approach. The effect of the fibres is assimilated to an infinite two-dimensional array of fictitious body forces in the matrix constituent phase of the unit cell. By subtracting a volume averaged strain polarization term from the integral equation we effectively embed a finite number of unit cells in a homogenized medium in which the overall stress and strain correspond to the volume averaged stress and strain of the constrained unit cell. This paper demonstrates that the zeroth term in the governing integral equation expansion, which embeds one unit cell in the homogenized medium, corresponds to the generalized self-consistent approximation. By comparing the zeroth term approximation with higher order approximations to the integral equation summation, both the accuracy of the generalized self-consistent composite model and the rate of convergence of the integral summation can be assessed. Two example composites are studied. For a tungsten/copper elastic fibrous composite the generalized self-consistent model is shown to provide accurate, effective, elastic moduli and local field representations. The local elastic transverse stress field within the representative volume element of the generalized self-consistent method is shown to be in error by much larger amounts for a composite with periodically distributed voids, but homogenization leads to a cancelling of errors, and the effective transverse Young's modulus of the voided composite is shown to be in error by only 23% at a void volume fraction of 75%.

Walker, Kevin P.↗
DOE OSTI2024

Electrical Resistivity Tomography Monitoring of In Situ Soil Flushing at the Hanford 100-K East Area: 100KE Soil Flushing Monitoring

Former operations in the 100-KE Area at the Hanford Site resulted in vadose zone hexavalent chromium that provides a source of groundwater contamination. Previous efforts to remediate vadose zone chromium involved excavation and offsite treatment of contaminated soils. Although much of the chromium was removed, contamination still exists in native soil between the water table and the bottom of the pit, which has since been backfilled. In-situ soil flushing was tested at the 100-KE Area to accelerate the removal of the remaining hexavalent chromium in the vadose zone. Soil flushing works by applying clean flush water at the surface, which mobilizes and transports chromium as it migrates downward to the water table. Once the chromium reaches the water table, it is hydraulically contained, extracted, and treated through pump and treat operations. The efficacy of soil flushing is directly related to the volume of clean water that infiltrates through contaminated soils. Therefore, performance monitoring requires and understanding of flush water migration through the vadose zone. It is challenging to comprehensively assess soil flushing performance via borehole access due to the limited volume of investigation afforded by a given wellbore. As an alternative, 3D time-lapse electrical resistivity tomography (ERT) was tested as a method of monitoring the distribution of flush water over time within the vadose zone. ERT is a method of imaging the bulk electrical conductivity of the subsurface, which is highly dependent on water saturation levels in unconsolidated and unsaturated sediments. Thus, the timing and location of changes in bulk conductivity caused by soil flushing can be used to infer flush water migration pathways. In this report we present results of 3D time-lapse ERT imaging during two separate soil flushing campaigns conducted during the spring and summer months of 2022 and 2023. Results show generally that: 1) Pit backfill materials appear to nominally have larger permeability than native soils. Consequently, the boundary between pit backfill and native soil had a significant impact on flush water migration, causing some flush water to migrate along the pit boundary to the bottom of the pit. 2) Non-uniform flows, likely caused by variations in hydrogeologic properties, developed in the pit backfill materials, resulting in uneven flush water distribution on the southern margin of the soil flushing zone. 3) Redistribution of water at the interface between backfill materials and Hanford formation materials likely facilitated elevated and uniform distribution of flush water within native soils beneath the deeper parts of the pit boundary beneath the center of the flush zone, which presumably overlie soils with elevated chromium contamination. These areas appear to have been infiltrated by higher volumes of flush water than the northern and southern margins of the flush zone. 4) In comparison to 2022, high flush water application rates significantly improved flush water distribution throughout the target flushing zone. 5) Imaging resolution was limited to a depth of approximate 20 meters below the land surface, due primarily to limitations on the lateral extent of the surface ERT array. The ~10 m region of the vadose zone between approximately 130 meters elevation and the water table at approximately 120 meters elevation was unresolved.

100 Area↗
NASA NTRS1977

Remarks on the overall distribution of hydrogen in the galactic disk

The degree of saturation characterizing low altitude emission observations of H(I) and the optical depth corrections to the derived column and volume densities are discussed. The amount of fine-scale velocity and spatial structure diluted by the instrumental limitations of the presently available surveys are described. The general problem of detailed mapping of H(I) in the galaxy is explored. Comparison is made between the distribution of H(I) and that of CO and several other galactic tracers. Atomic hydrogen is unique in its distribution, instead of being typical of many Population I constituents. As defined by atomic hydrogen, the galactic disk has a diameter fully twice as large as that defined by the ionized and molecular states of hydrogen, as well as by other molecules, supernova remnants, pulsars, gamma-radiation, synchroton radiation, and the youngest stars. It is also less confined to the galactic equator than most of the other constituents. The degree of small scale structure apparent in the molecular observations is much greater than that in the H(I) observations.

Burton, W. B.↗
DOE OSTI2025

Resin chemistry and particle size influence on stereolithography with silicon carbide

Stereolithography (SLA) is an established process able to produce high resolution polymer parts with complex geometries. Silicon carbide (SiC) has uses in a variety of applications, but traditionally was difficult to manufacture into complex geometries. There have been advances in producing SiC through SLA using a SiC-derived ceramic such as silicon oxycarbide (SiOC). In this study, a slurry using a commercially available resin as the base material with additional modifiers was investigated to create a SiC slurry ready for pressureless sintering. The effects of photoinitiator, dispersant and a bimodal distribution of SiC particle sizes was studied using a design of experiments (DOE). A slurry with a bimodal distribution of 70 % coarse and 30 % fine SiC powder at 40 % solids loading by volume was prepared and successfully printed. Rheology measurements show the slurry to have viscoelastic shear thinning behavior below the recommended 1000 Pas necessary for printing. Printing parameters for the new material on a commercially available SLA printer were studied parametrically. The laser marking speeds found to print the slurry was 260 mm/s and 130 mm/s. A slurry and printing parameters were determined to produce a green part with a proposed debinding cycle.

Herd, Tien [ORNL]↗
DOE OSTI2022

Stable all-solid-state sodium-sulfur batteries for low-temperature operation enabled by sodium alloy anode and confined sulfur cathode

All-solid-state sodium-sulfur (Na-S) batteries are promising for stationary energy storage devices because of their low operating temperatures (less than 100 °C), improved safety, and low-cost fabrication. Using Na alloy instead of Na metal as an anode in Na-S batteries can prevent dendrite growth and improve interfacial stability between the anode and solid electrolytes to achieve long-cycling stability. A high-sulfur content cathode possessing high sulfur utilization is also important to enable an energy-dense Na-S battery. In this work, we studied Na-Sb and Na- Sn alloy anodes and demonstrated the superiority of Na 3 Sb alloy undergoing a stable Na alloying/dealloying process at 0.04 mA cm -2 for over 500 hours. Combining the optimized Na3Sb alloy anode with sulfur-carbon composites prepared by the vapor deposition approach, the full cell shows a high sulfur specific capacity and improved rate performance. Moreover, the all-solid-state Na alloy-S battery can deliver a high initial discharge specific capacity of 1377 mAh g -1 and maintain good capacity retention of 70 % after 180 cycles at 60 °C. Further, post-cycle characterizations show that both the anode and cathode perform a reversible discharge/charge process after the 1st cycle, and the cathode undergoes significantly rearranged distributions of carbon and solid-state electrolytes after 180 cycles due to severe volume change induced by repeated sodiation/desodiation process.

25 ENERGY STORAGE↗
DOE OSTI2022

Radiative transfer in stars by feebly interacting bosons

Starting from first principles, we study radiative transfer by new feebly-interacting bosons (FIBs) such as axions, axion-like particles (ALPs), dark photons, and others. Our key simplification is to include only boson emission or absorption (including decay), but not scattering between different modes of the radiation field. Based on a given distribution of temperature and FIB absorption rate in a star, we derive explicit volume-integral expressions for the boson luminosity, reaching from the free-streaming to the strong-trapping limit. The latter is seen explicitly to correspond to quasi-thermal emission from a “FIB sphere” according to the Stefan-Boltzmann law. Our results supersede expressions and approximations found in the recent literature on FIB emission from a supernova core and, for radiatively unstable FIBs, provide explicit expressions for the nonlocal (“ballistic”) transfer of energy recently discussed in horizontal-branch stars.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Efficient Data Compression for 3D Sparse TPC via Bicephalous Convolutional Autoencoder

Real-time data collection and analysis in large experimental facilities present a great challenge across multiple domains, including high energy physics, nuclear physics, and cosmology. To address this, machine learning (ML)-based methods for real-time data compression have drawn significant attention. However, unlike natural image data, such as CIFAR and ImageNet that are relatively small-sized and continuous, scientific data often come in as three-dimensional 3D data volumes at high rates with high sparsity (many zeros) and non-Gaussian value distribution. This makes direct application of popular ML compression methods, as well as conventional data compression methods, suboptimal. To address these obstacles, this work introduces a dual-head autoencoder to resolve sparsity and regression simultaneously, called Bicephalous Convolutional AutoEncoder (BCAE). This method shows advantages both in compression fidelity and ratio compared to traditional data compression methods, such as MGARD, SZ, and ZFP. To achieve similar fidelity, the best performer among the traditional methods can reach only half the compression ratio of BCAE. Moreover, a thorough ablation study of the BCAE method shows that a dedicated segmentation decoder improves the reconstruction.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

3-D reconstruction and microstructural characterization of neutron-irradiated U-10Zr fuel using FIB-SEM serial sectioning

Herein, focused ion beam-scanning electron microscopy serial sectioning was applied to characterize the three-dimensional (3-D) porosity and phase regions of a neutron-irradiated U-10 wt% Zr fuel. The specimen was removed from an intermediate radial region of a fuel pin irradiated to 5.7 at.% burn-up. Backscattered electron imaging and energy-dispersive spectroscopy were performed on each serial section, allowing for the characterization of microstructural morphology and composition. Porosity size followed a lognormal distribution, ranging from 1.46 × 10 –4 to 25.58 µm 3 with a total porosity volume fraction of 13.02%. Distinctive microstructural regions were identified by composition and porosity: (1) a Zr-rich region with an average composition of 28.4 wt% Zr and a local porosity fraction of 6.88%, and (2) a U-rich region with an average composition of 97.0 wt% U and a local porosity fraction of 14.11%; subdivided into U-rich—high porosity (16.68%) and U-rich—low porosity (8.04%) regions. The detailed 3-D compositional and porosity regions can improve nuclear fuel performance codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Reaction Rate Distribution Measurements in ZPPR-15

Small metal foils were irradiated in ZPPR-15 to measure distributions for 239 Pu(n,f), 235 U(n,f), 238 U(n,f), 238 U(n,γ), 115 In(n,n’) and 115 In(n,γ) reaction rates in ZPPR-15. The measured data were reported as basic reaction rate distributions for individual foils, cell-averaged reaction rate distributions and spectral indices or reaction rate ratios. All of the measured data were analyzed and tabulated in such a manner that the data can be readily compared with computed values. The published uncertainties for ZPPR-15 the reaction rate measurements include the statistical uncertainties in the measurements, reproducibility uncertainty and small uncertainties related to corrections for items such as foil compositions and post-irradiation decay between reactor shutdown and foil measurement. There are additional uncertainty components related to detector calibration that are not included in the published uncertainties. A full uncertainty analysis was performed for each foil measurement and for quantities derived from the basic foil measurements. The significant uncertainties were quantified, and a total uncertainty was derived for each measured value. The ZPPR-15 experimental records were used to create detailed as-built Monte Carlo models for the foil reaction rate measurements in ZPPR-15 loadings 123, 134 and 203 and for the fission chamber measurements of 237 Np and 242 Pu fission rates in ZPPR-15 loading 141. Because there were many foils distributed in the ZPPR-15 assembly and because an individual foil occupies a negligible volume in the ZPPR-15 assembly, direct Monte Carlo calculations of the measured foil reaction rates would require an impractical computational effort. The as-built Monte Carlo models and related files were prepared for conversion to deterministic models that can be calculated with realistic computational effort.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

High-Energy X-ray Diffraction Microscopy for Nuclear Forensics (FY23 Project Report)

Morphological information on nuclear material has been identified using visible light and scanning electron microscopy. These identify qualitative differences in particle morphology. Three-dimensional imaging of materials through alternating scanning electron microscopy imaging and focused ion beam milling has also been used. Unfortunately, these techniques are time- and labor-intensive, with significant sample preparation required and lengthy analysis times. Further, the resulting 3D images are qualitative, require manual identification, and do not capture statistically-representative populations. High energy X-ray 3D imaging using a direct-beam or diffracted-beam (High-Energy Diffraction Microscopy) have been developed at the Advanced Photon Source and can produce quantitative information on grains (phase, location, etc.) and pores (size distribution, sphericity) in a material. These techniques require only minutes to characterize a sample volume and are non-destructive, thus suitable for a wide range of existing samples and for confirmatory analyses to be carried out using conventional microscopy techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Final Report: Enhanced Algal Production of CA for Improved Atmospheric Delivery of CO2 To Ponds

Technologies that enable direct-air-capture (DAC) of CO2 and eliminate the need for a CO2 capture, storage, and distribution system would significantly reduce the cost of algal production, and greatly increase the volume of algae biomass that can be produced by enabling algae farms to be located anywhere. Such technologies include cultivation under high alkalinity/high pH conditions, which increase the driving force for CO2 absorption, and development of genetic tools and genetically engineered strains to decorate the surface of the algae with carbonic anhydrase (CA), enable secretion of CA by the algae, or more generally boost the performance of the carbon concentrating mechanism (CCM).

09 BIOMASS FUELS↗
DOE OSTI2025

Long-Range Transport of Biomass Burning Aerosols from Southern Africa: A Case Study Using Layered Atlantic Smoke Interactions with Clouds Observations

A case study of an incoming biomass burning aerosol plume at Ascension Island is analyzed for the peak of the 2017 fire season using satellites, reanalysis and in situ observations. Measurements from the Atmospheric Radiation Measurement Mobile Facility 1 reveal an abrupt change from relatively clean conditions (~70 parts per billion by volume of carbon monoxide) to a more polluted state (~150 parts per billion by volume of carbon monoxide). Corresponding changes in aerosol size reveal a broadening of size distributions toward larger optical diameters, consistent with the arrival of aged aerosols. Within a 24 h period, black carbon fraction increases ~500% from ~300 ng m e to ~1500 ng m 3 , while light absorption coefficients increase ~300%. Long-range transport of these aerosols is primarily confined between 2 and 5 km above sea level along the northwesterly trade winds. Our results show that the primary driver of increases in aerosol loading over Ascension Island is an intensification of the St. Helena high-pressure system (anticyclone) that leads to a weakening of trade winds and increases westward transport on its northern flank. A better understanding of the complex interactions between air quality, meteorology and long-range aerosol transport is important for future modeling studies focused on aerosol–cloud–radiation interactions over the open ocean and reducing its associated uncertainties.

aerosol size distribution↗
NASA NTRS1966

Impurity distribution in MgO.

Microprobe study of impurities in hot-pressed polycrystalline MgO compact and existence of significant grain boundary volume

IMPURITY↗
NASA NTRS1976

Terminal area energy management regime investigations utilizing an 0.030-scale model (47-0) of the space shuttle vehicle orbiter configuration 140A/B/C/R in the Ames Research Center 11 x 11 foot transonic wind tunnel (0A148), volume 1

Data obtained in wind tunnel tests are presented. The objectives of the tests were to: (1) obtain pressure distributions, forces and moments over the vehicle 5 Orbiter in the terminal area energy management (TAEM) and approach phases of flight; (2) obtain elevon and rudder hinge moments in the TAEM and approach phases of flight; (3) obtain body flap and elevon loads for verification of loads balancing with integrated pressure distributions; and (4) obtain pressure distributions near the short OMS pods in the high subsonic, transonic and low supersonic Mach number regimes. Testing was conducted over a Mach number range from 0.6 to 1.4 with Reynolds number variations from 4.57 million to 2.74 million per foot. Model angle-of-attack was varied from -4 to 16 degrees and angles of side slip ranged from -8 to 8 degrees.

Hawthorne, P. J.↗