Results for “user interfaces” — Page 55

NASA NTRS2003

Developing a MATLAB(registered)-Based Tool for Visualization and Transformation

An important step in the structural design and development of spacecraft is the experimental identification of a structure s modal characteristics, such as its natural frequencies and modes of vibration. These characteristics are vital to developing a representative model of any given structure or analyzing the range of input frequencies that can be handled by a particular structure. When setting up such a representative model of a structure, careful measurements using precision equipment (such as accelerometers and instrumented hammers) must be made on many individual points of the structure in question. The coordinate location of each data point is used to construct a wireframe geometric model of the structure. Response measurements obtained from the accelerometers is used to generate the modal shapes of the particular structure. Graphically, this is displayed as a combination of the ways a structure will ideally respond to a specified force input. Two types of models of the tested structure are often used in modal analysis: an analytic model showing expected behavior of the structure, and an experimental model showing measured results due to observed phenomena. To evaluate the results from the experimental model, a comparison of analytic and experimental results must be made between the two models. However, comparisons between these two models become difficult when the two coordinate orientations differ in a manner such that results are displayed in an unclear fashion. Such a problem proposes the need for a tool that not only communicates a graphical image of a structure s wireframe geometry based on various measurement locations (called nodes), but also allows for a type of transformation of the image s coordinate geometry so that a model s coordinate orientation is made to match the orientation of another model. Such a tool should also be designed so that it is able to construct coordinate geometry based on many different listings of node locations and is able to transform the wireframe coordinate orientation to match almost any possible orientation (i.e. it should not be a problem specific application) if it is to be of much value in modal analysis. Also, since universal files are used to store modal parameters and wireframe geometry, the tool must be able to read and extract information from universal files and use these files to exchange model data.The purpose of this project is to develop such a tool as a computer graphical user interface (GUI) capable of performing the following tasks: 1) Browsing for a particular universal file within the computer directory and displaying the name of this file to the screen; 2) Plotting each of the nodes within the universal file in a useful, descriptive, and easily understood figure; 3) Reading the node numbers from the selected file and listing these node numbers to the user for selection in an easily accessible format; 4) Allowing for user selection of a new model orientation defined by three selected nodes; and 5) Allowing the user to specify a directory to which the transformed model s node locations will be saved, and saving the transformed node locations to the specified file.

Anderton, Blake J.↗

NASA NTRSDate not supplied

An Integrated Design Tool for Tow-Steered Laminates of Composites in Abaqus and MSC.Patran/Nastran

Tow-steered composites can be tailored for optimal mechanical performance of lightweight structures. However, there are no commercial-grade design tools for tow-steered composite structures, which hinders the design innovation of tow-steered composites in realistic structures. The novelty of this paper is to develop an integrated design framework along with the development of graphical user interface (GUI) plug-ins in commercial finite element (FE) software Abaqus and MSC.Patran/Nastran. The GUI plug-ins take all the design setups and communicate with external codes for the material modeling and optimization, and hence provide a unified design environment within the FE codes. The mechanics of structure genome (MSG) plate model computes shell element properties based on user-defined fiber paths and layup, which are defined via the GUI plug-ins. The optimization is performed by an open-source code, Dakota, from Sandia National Laboratories (Sandia), which also coordinates the structural analysis, material modeling, and optimization in design iterations. Two examples are presented to demonstrate the user-friendliness and versatility of the developed GUI plug-ins. The developed tools will ease the design process and facilitate the application of tow-steered composites in realistic aerospace structures.

Xin Liu↗

NASA NTRSDate not supplied

An Integrated Design Tool for Tow-Steered Laminates of Composites in Abaqus and MSC.Patran/Nastran

Tow-steered composites can be tailored for optimal mechanical performance of lightweight structures. However, there are no commercial-grade design tools for tow-steered composite structures, which hinders the design innovation of tow-steered composites in realistic structures. The novelty of this paper is to develop an integrated design framework along with the development of graphical user interface (GUI) plug-ins in commercial finite element (FE) software Abaqus and MSC.Patran/Nastran. The GUI plug-ins take all the design setups and communicate with external codes for the material modeling and optimization, and hence provide a unified design environment within the FE codes. The mechanics of structure genome (MSG) plate model computes shell element properties based on user-defined fiber paths and layup, which are defined via the GUI plug-ins. The optimization is performed by an open-source code, Dakota, from Sandia National Laboratories (Sandia), which also coordinates the structural analysis, material modeling, and optimization in design iterations. Two examples are presented to demonstrate the user-friendliness and versatility of the developed GUI plug-ins. The developed tools will ease the design process and facilitate the application of tow-steered composites in realistic aerospace structures.

Xin Liu↗

NASA NTRS1995

An adaptable product for material processing and life science missions

The Experiment Control System II (ECS-II) is designed to make available to the microgravity research community the same tools and mode of automated experimentation that their ground-based counterparts have enjoyed for the last two decades. The design goal was accomplished by combining commercial automation tools familiar to the experimenter community with system control components that interface with the on-orbit platform in a distributed architecture. The architecture insulates the tools necessary for managing a payload. By using commercial software and hardware components whenever possible, development costs were greatly reduced when compared to traditional space development projects. Using commercial-off-the-shelf (COTS) components also improved the usability documentation, and reducing the need for training of the system by providing familiar user interfaces, providing a wealth of readily available documentation, and reducing the need for training on system-specific details. The modularity of the distributed architecture makes it very amenable for modification to different on-orbit experiments requiring robotics-based automation.

Wassick, Gregory↗

NASA NTRS2002

Software for Partly Automated Recognition of Targets

The Feature Analyst is a computer program for assisted (partially automated) recognition of targets in images. This program was developed to accelerate the processing of high-resolution satellite image data for incorporation into geographic information systems (GIS). This program creates an advanced user interface that embeds proprietary machine-learning algorithms in commercial image-processing and GIS software. A human analyst provides samples of target features from multiple sets of data, then the software develops a data-fusion model that automatically extracts the remaining features from selected sets of data. The program thus leverages the natural ability of humans to recognize objects in complex scenes, without requiring the user to explain the human visual recognition process by means of lengthy software. Two major subprograms are the reactive agent and the thinking agent. The reactive agent strives to quickly learn the user's tendencies while the user is selecting targets and to increase the user's productivity by immediately suggesting the next set of pixels that the user may wish to select. The thinking agent utilizes all available resources, taking as much time as needed, to produce the most accurate autonomous feature-extraction model possible.

Opitz, David↗

NASA NTRS2004

Analyzing Spacecraft Telecommunication Systems

Multi-Mission Telecom Analysis Tool (MMTAT) is a C-language computer program for analyzing proposed spacecraft telecommunication systems. MMTAT utilizes parameterized input and computational models that can be run on standard desktop computers to perform fast and accurate analyses of telecommunication links. MMTAT is easy to use and can easily be integrated with other software applications and run as part of almost any computational simulation. It is distributed as either a stand-alone application program with a graphical user interface or a linkable library with a well-defined set of application programming interface (API) calls. As a stand-alone program, MMTAT provides both textual and graphical output. The graphs make it possible to understand, quickly and easily, how telecommunication performance varies with variations in input parameters. A delimited text file that can be read by any spreadsheet program is generated at the end of each run. The API in the linkable-library form of MMTAT enables the user to control simulation software and to change parameters during a simulation run. Results can be retrieved either at the end of a run or by use of a function call at any time step.

Kordon, Mark↗

NASA NTRS2003

Software for Partly Automated Recognition of Targets

The Feature Analyst is a computer program for assisted (partially automated) recognition of targets in images. This program was developed to accelerate the processing of high-resolution satellite image data for incorporation into geographic information systems (GIS). This program creates an advanced user interface that embeds proprietary machine-learning algorithms in commercial image-processing and GIS software. A human analyst provides samples of target features from multiple sets of data, then the software develops a data-fusion model that automatically extracts the remaining features from selected sets of data. The program thus leverages the natural ability of humans to recognize objects in complex scenes, without requiring the user to explain the human visual recognition process by means of lengthy software. Two major subprograms are the reactive agent and the thinking agent. The reactive agent strives to quickly learn the user s tendencies while the user is selecting targets and to increase the user s productivity by immediately suggesting the next set of pixels that the user may wish to select. The thinking agent utilizes all available resources, taking as much time as needed, to produce the most accurate autonomous feature-extraction model possible.

Opitz, David↗

NASA NTRS2004

Software for Analyzing Sequences of Flow-Related Images

Spotlight is a computer program for analysis of sequences of images generated in combustion and fluid physics experiments. Spotlight can perform analysis of a single image in an interactive mode or a sequence of images in an automated fashion. The primary type of analysis is tracking of positions of objects over sequences of frames. Features and objects that are typically tracked include flame fronts, particles, droplets, and fluid interfaces. Spotlight automates the analysis of object parameters, such as centroid position, velocity, acceleration, size, shape, intensity, and color. Images can be processed to enhance them before statistical and measurement operations are performed. An unlimited number of objects can be analyzed simultaneously. Spotlight saves results of analyses in a text file that can be exported to other programs for graphing or further analysis. Spotlight is a graphical-user-interface-based program that at present can be executed on Microsoft Windows and Linux operating systems. A version that runs on Macintosh computers is being considered.

Klimek, Robert↗

NASA NTRS1995

Geophysical data analysis and visualization using the Grid Analysis and Display System

Several problems posed by the rapidly growing volume of geophysical data are described, and a selected set of existing solutions to these problems is outlined. A recently developed desktop software tool called the Grid Analysis and Display System (GrADS) is presented. The GrADS' user interface is a natural extension of the standard procedures scientists apply to their geophysical data analysis problems. The basic GrADS operations have defaults that naturally map to data analysis actions, and there is a programmable interface for customizing data access and manipulation. The fundamental concept of the GrADS' dimension environment, which defines both the space in which the geophysical data reside and the 'slice' of data which is being analyzed at a given time, is expressed The GrADS' data storage and access model is described. An argument is made in favor of describable data formats rather than standard data formats. The manner in which GrADS users may perform operations on their data and display the results is also described. It is argued that two-dimensional graphics provides a powerful quantitative data analysis tool whose value is underestimated in the current development environment which emphasizes three dimensional structure modeling.

Doty, Brian E.↗

NASA NTRSDate not supplied

The Environmental Data Application for Analysis of Space Telemetry Data

Sensors on the International Space Station (ISS) and multiple spacecraft elsewhere in Earth orbit and in deep space continuously monitor and collect environmental data, transmitting this information back to Earth. These data include ionizing radiation and, on the ISS and spacecrafts, CO2, relative humidity levels, and temperature, and are of great importance to space biology research. Looking ahead to future long duration crewed missions beyond low Earth orbit, the ability to study how factors including CO2 levels, light cycle, temperature modulate the response to ionizing radiation and microgravity is essential. To date, access to these data has been fragmented across space agencies, spacecraft, and databases. To address this issue, NASA’s Open Science Data Repository (OSDR) has developed a user interface for interrogation of telemetry data: the Environmental Data Application (EDA). The EDA provides the capability to visualize telemetry and radiation data collected on the International Space Station and corresponding ground platforms during the Rodent Research missions. Telemetry data includes temperature, relative humidity, and CO2 levels. Radiation data includes galactic cosmic rays, the contribution of the South Atlantic Anomaly, total radiation dose rate, and accumulated radiation dose. The application allows users to view single missions, compare multiple missions, and view and download summary or full data tables. In summary, the EDA provides GUIs for data visualization and exploration, as well as means for data export, making these data FAIR (Findable, Accessible, Interoperable, and Reusable), complementing the biological data contained in OSDR, and providing the space science community with a valuable resource for scientific analyses.

telemetry↗

DOE OSTI2021

FY21 Progress Report: SRNL Analysis of ICCWR LCM and WAMS data for Corrosion and Cracking

The development of algorithms for machine learning and data analysis for the 3013 Surveillance Program is a collaborative effort by the Savannah River National Laboratory (SRNL) and the University of South Carolina (USC). For corrosion detection, Laser Confocal Microscope (LCM) or Wide Area 3D Measurement System (WAMS) data is extracted from large binary files, with software written to convert the data to physical attributes (e.g., height, color and grayscale values; all as functions of a location in a plane projection). A user-friendly Matlab Graphical User Interface (GUI) that reads data from either LCM or WAMS files was developed to integrate input data with software developed for processing and evaluation. The GUI can selectively download binary data, interrogate data attributes, label data, flag significant features, execute Machine Learning (ML) algorithms, output parameters for trained ML algorithms, report ML model accuracy with respect to labeled data, and generate graphical representations for various analyses. Features can be called out by user-specified thresholds, manual labeling or machine learning algorithms when they have been completed. The ability to rapidly label data is important because of the volume of data required for training machine learning algorithms. The GUI has the flexibility to allow addition of improved ML algorithms, methods for data visualization, and statistical computations. Statistical analyses via the GUI include areas of pits within a defined range of pit depths, correlations between Red-Green-Blue (RGB) or grayscale intensity and relative surface height, covariances between values associated with features, and feature histograms. The development of supervised machine learning algorithms, however, has been hindered by a lack of training data. The machine learning algorithms for crack identification are being refined but require improvements to the true positive rate for crack detection. This shortcoming is an artifact of the limited training data currently available, perhaps more so than the structure of the neural networks. At present, the best results are had from a consensus over an ensemble of randomly generated Deep Neural Network (DNN) or Convolutional Neural Network (CNN) algorithms. Although the consensus accuracy method has yielded optimum true positive and true negative rates in excess of 80%, additional validation testing is necessary. In addition to the suite of LCM data that was initially used, and which represents the majority of the work presented in this report, WAMS image data was also reviewed at a preliminary level. The review included a comparison between image resolution and dynamic range for each method. WAMS (ZON file) image data was found to have a pixel pitch of 3.69μm compared to 1 μm for the LCM (vk4 file) data, which implies a lower resolution for the WAMS images. Conversely, the ratio of dynamic range of the WAMS data to the LCM data was approximately 41:20 for height data, suggesting that information from WAMS should more accurately determine the depth of pits. At present, the significance of the greater dynamic range of the WAMS data relative to the LCM data has not yet been evaluated.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS1992

A demonstration of an intelligent control system for a reusable rocket engine

An Intelligent Control System for reusable rocket engines is under development at NASA Lewis Research Center. The primary objective is to extend the useful life of a reusable rocket propulsion system while minimizing between flight maintenance and maximizing engine life and performance through improved control and monitoring algorithms and additional sensing and actuation. This paper describes current progress towards proof-of-concept of an Intelligent Control System for the Space Shuttle Main Engine. A subset of identifiable and accommodatable engine failure modes is selected for preliminary demonstration. Failure models are developed retaining only first order effects and included in a simplified nonlinear simulation of the rocket engine for analysis under closed loop control. The engine level coordinator acts as an interface between the diagnostic and control systems, and translates thrust and mixture ratio commands dictated by mission requirements, and engine status (health) into engine operational strategies carried out by a multivariable control. Control reconfiguration achieves fault tolerance if the nominal (healthy engine) control cannot. Each of the aforementioned functionalities is discussed in the context of an example to illustrate the operation of the system in the context of a representative failure. A graphical user interface allows the researcher to monitor the Intelligent Control System and engine performance under various failure modes selected for demonstration.

Musgrave, Jeffrey L.↗

NASA NTRS1989

REDEX: The ranging equipment diagnostic expert system

REDEX, an advanced prototype expert system that diagnoses hardware failures in the Ranging Equipment (RE) at NASA's Ground Network tracking stations is described. REDEX will help the RE technician identify faulty circuit cards or modules that must be replaced, and thereby reduce troubleshooting time. It features a highly graphical user interface that uses color block diagrams and layout diagrams to illustrate the location of a fault. A semantic network knowledge representation technique was used to model the design structure of the RE. A catalog of generic troubleshooting rules was compiled to represent heuristics that are applied in diagnosing electronic equipment. Specific troubleshooting rules were identified to represent additional diagnostic knowledge that is unique to the RE. Over 50 generic and 250 specific troubleshooting rules have been derived. REDEX is implemented in Prolog on an IBM PC AT-compatible workstation. Block diagram graphics displays are color-coded to identify signals that have been monitored or inferred to have nominal values, signals that are out of tolerance, and circuit cards and functions that are diagnosed as faulty. A hypertext-like scheme is used to allow the user to easily navigate through the space of diagrams and tables. Over 50 graphic and tabular displays have been implemented. REDEX is currently being evaluated in a stand-alone mode using simulated RE fault scenarios. It will soon be interfaced to the RE and tested in an online environment. When completed and fielded, REDEX will be a concrete example of the application of expert systems technology to the problem of improving performance and reducing the lifecycle costs of operating NASA's communications networks in the 1990's.

Luczak, Edward C.↗

NASA NTRS1989

REDEX - The ranging equipment diagnostic expert system

REDEX, an advanced prototype expert system that diagnoses hardware failures in the Ranging Equipment (RE) at NASA's Ground Network tracking stations is described. REDEX will help the RE technician identify faulty circuit cards or modules that must be replaced, and thereby reduce troubleshooting time. It features a highly graphical user interface that uses color block diagrams and layout diagrams to illustrate the location of a fault. A semantic network knowledge representation technique was used to model the design structure of the RE. A catalog of generic troubleshooting rules was compiled to represent heuristics that are applied in diagnosing electronic equipment. Specific troubleshooting rules were identified to represent additional diagnostic knowledge that is unique to the RE. Over 50 generic and 250 specific troubleshooting rules have been derived. REDEX is implemented in Prolog on an IBM PC AT-compatible workstation. Block diagram graphics displays are color-coded to identify signals that have been monitored or inferred to have nominal values, signals that are out of tolerance, and circuit cards and functions that are diagnosed as faulty. A hypertext-like scheme is used to allow the user to easily navigate through the space of diagrams and tables. Over 50 graphic and tabular displays have been implemented. REDEX is currently being evaluated in a stand-alone mode using simulated RE fault scenarios. It will soon be interfaced to the RE and tested in an online environment. When completed and fielded, REDEX will be a concrete example of the application of expert systems technology to the problem of improving performance and reducing the lifecycle costs of operating NASA's communications networks in the 1990s.

Luczak, Edward C.↗

NASA NTRS1981

The role of pilots

The need for detailed specifications is addressed. Candidates for standardization include hardware interfaces, communication protocols, and data exchange services. Atmosphere, Ocean, and Resource pilot programs, utilization of current techniques and technologies in the use and exchange of data and to facilitate access to data are discussed. Pilot objectives aim to: (1) demonstrate the use of advanced technologies, (2) provide a test bed environment for data handling technique evaluation, (3) evolve requirements and capabilities, and (4) document validated methodologies as standards and guidelines for data systems planning use. A user oriented catalog system, data set management, a network communication system, and a user interface are also discussed.

Gary, J. P.↗

DOE OSTI2024

Utilizing HYSPLIT for Emergency Response Modeling at SRS

The threat of a disaster happening at the Savannah River Site (SRS) is low, but not zero. When an emergency arises, emergency responders utilize a variety of tools to detect, track, and mitigate the disaster. HYSPLIT is a community atmospheric dispersion model that is highly configurable and has been used operationally to simulate particle, chemical, and radionuclide releases. We have developed a preliminary user interface (UI) that configures HYSPLIT to run for a variety of Emergency Action Level (EAL) scenarios at SRS. Using a hypothetical EAL scenario of an accidental release of Pu-238 in H-area and K-area onsite, an analysis was done to show how a preliminary UI framework allows HYSPLIT to be run on a terminal without the need form an active network connection. The study was successful in multiple aspects. For the preliminary UI, users were able to input certain characteristics of the hypothetical EAL such as hours of emission (how long was Pu-238 being released), curies of release, release start time (when does the model run start), and type of radionuclide directly into the terminal. For HYSPLIT, the model was successful in being able to take the UI input, calculate the results from the inputs and output multiple figures of both total volumetric airborne concentrations and surface deposition. We used the Pu-238 Derived Intervention Level (DIL) deposition thresholds for produce, dairy, and beef for visualization of the surface deposition, showing how a release would impact ingestion pathways.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2020

Systems and methods for monitoring a power-generation module assembly after a power-generation module shutdown event

Embodiments are directed to providing a user interface (UI) that streamlines and simplifies the process of monitoring critical power-generation module (PGM) parameters after a PGM assembly is shutdown. The UI displays, in real-time, indicators corresponding to one or more post-shutdown PGM parameters. The UI provides indications of whether the post-shutdown PGM parameters meet post-shutdown criteria of the PGM assembly. When a post-shutdown PGM parameter does not meet the post-shutdown criteria, a user alert is provided to the user. A protocol may additionally be provided to the user. In some embodiments, the protocol may enable the user to return the PGM assembly to a condition that satisfies the post-shutdown criteria. The protocol may be a safety protocol and/or an asset protection protocol.

Buenaventura, Don↗

DOE OSTI2022

Systems and methods for monitoring a power-generation module assembly after a power-generation module shutdown event

Embodiments are directed to providing a user interface (UI) that streamlines and simplifies the process of monitoring critical power-generation module (PGM) parameters after a PGM assembly is shutdown. The UI displays, in real-time, indicators corresponding to one or more post-shutdown PGM parameters. The UI provides indications of whether the post-shutdown PGM parameters meet post-shutdown criteria of the PGM assembly. When a post-shutdown PGM parameter does not meet the post-shutdown criteria, a user alert is provided to the user. A protocol may additionally be provided to the user. In some embodiments, the protocol may enable the user to return the PGM assembly to a condition that satisfies the post-shutdown criteria. The protocol may be a safety protocol and/or an asset protection protocol.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗