Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “time dependent behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Auto Stop-Start Fuel Consumption Benefits

With increasingly stringent regulations mandating the improvement of vehicle fuel economy, automotive manufacturers face growing pressure to develop and implement technologies that improve overall system efficiency. One such technology is an automatic (auto) stop-start feature. Auto stop-start reduces idle time and reduces fuel use by temporarily shutting the engine off when the vehicle comes to a stop and automatically re-starting it when the brake is released, or the accelerator is pressed. As mandated by the U.S. Congress, the U.S. Environmental Protection Agency (EPA) is required to keep the public informed about fuel saving practices. This is done, in partnership with the U.S. Department of Energy (DOE), through the fueleconomy.gov website. The “Fuel-Saving Technologies” and “Gas Mileage Tips” sections of the website are focused on helping the public make informed purchasing decisions and encouraging fuel-saving driving habits. Here, in order to provide users with accurate information about the auto stop-start feature, experiments were conducted to determine its fuel economy effect. Four vehicles were tested both with and without the feature enabled under three test cycles: the Federal Test Procedure (FTP) city fuel economy test, the US06 high acceleration aggressive driving schedule that is often identified as the “Supplemental FTP” driving schedule, and the EPA New York City Cycle (NYCC). The results were compared to measure the fuel economy and consumption effects of using the auto stop-start feature. It was found that the fuel economy improvement varied significantly between drive cycles depending on the amount and percentage of idle time during the test. The largest fuel economy improvements were 7.27% and 26.4% for the FTP and NYCC, respectively.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Mechanical performance of co-deposited immiscible Cu–Ta thin films

Abstract The immiscible alloy Cu–Ta has the potential for enhanced mechanical performance in applications as a functional coating. To establish baseline mechanical properties, four Cu–Ta films were co-sputtered at the temperatures 23, 400, 600, and 800 °C and tested with nanoindentation at strain rates 5 $$\times $$ × 10 −3 s −1 to 10 s −1 . Each film had a unique microstructure morphology. The hardness and elastic modulus of the four films were insensitive to strain rate changes. Instead, the measured properties were spatially dependent, particularly in the 600 and 800 °C films. In those two films, there is a bimodal deformation behavior due to Cu-agglomeration under protruding grains and planar Ta-rich regions. Increasing the indentation depth revealed shear band suppression which is related to a homogenous distribution of flow stresses for all four microstructure morphologies. Finally, the Cu–Ta hardness appeared to follow a rule-of-mixtures when compared to extrapolated data of Cu and Ta monolithic films.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Simulations of Stochastic Fluid Dynamics near a Critical Point in the Phase Diagram

Here, we present simulations of stochastic fluid dynamics in the vicinity of a critical endpoint belonging to the universality class of the Ising model. This study is motivated by the challenge of modeling the dynamics of critical fluctuations near a conjectured critical endpoint in the phase diagram of quantum chromodynamics (QCD). We focus on the interaction of shear modes with a conserved scalar density, which is known as model H. We show that the observed dynamical scaling behavior depends on the correlation length and the shear viscosity of the fluid. As the correlation length is increased or the viscosity is decreased we observe a crossover from the dynamical exponent of critical diffusion, z≃4, to the expected scaling exponent of model H, z≃3. We use our method to investigate the time-dependent correlation function of non-Gaussian moments M n (t) of the order parameter. We find that the relaxation time depends in a nontrivial manner on the power n.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Numerical Analysis of Time Resolved Photoluminescence for Alumina/Cd(Se,Te) Double Heterostructures

Al2O3 has demonstrated excellent Cd(Se,Te) surface passivation. In this work, recombination mechanisms were investigated by comparing simulations of time resolved photoluminescence (TRPL) to PL decay data (320 ns effective lifetime) for Al2O3 /Cd(Se,Te)/Al2O3 double heterostructures. Models were employed to investigate the effects of bulk and surface recombination, electric fields, mobility, and doping by simulating intensity-dependent single- (1PE) and two-photon excitation (2PE) TRPL. 2PE simulations replicate decay behavior while 1PE simulations require attention to charge redistribution. Various coupled mechanisms cannot be distinguished from PL decay data alone. Complementary measurements are required to constrain the model parameters and isolate mechanisms.

CdTe↗
NASA NTRS1991

Elevated temperature fracture of RS/PM aluminum alloy 8009

The fracture behavior of advanced powder metallurgy Al-Fe-V-Si alloy 8009 (previously called FVS0812) is being characterized under monotonic loads, as a function of temperature. Particular attention is focused on contributions to the fracture mechanism from the fine grained dispersoid strengthened microstructure, dissolved solute from rapid solidification, and the moist air environment. Time-dependent crack growth is characterized in advanced aluminum alloys at elevated temperatures with the fracture mechanics approach, and cracking mechanisms are examined with a metallurgical approach. Specific tasks were to obtain standard load crack growth experimental information from a refined testing system; to correlate crack growth kinetics with the j-integral and time dependent C(sub t)(t); and to investigate the intermediate temperature embrittlement of 8009 alloy in order to understand crack growth mechanisms.

Porr, William C., Jr.↗
NASA NTRS1991

Control of unsteady separated flow associated with the dynamic pitching of airfoils

Although studies have been done to understand the dependence of parameters for the occurrence of deep stall, studies to control the flow for sustaining lift for a longer time has been little. To sustain the lift for a longer time, an understanding of the development of the flow over the airfoil is essential. Studies at high speed are required to study how the flow behavior is dictated by the effects of compressibility. When the airfoil is pitched up in ramp motion or during the upstroke of an oscillatory cycle, the flow development on the upper surface of the airfoil and the formation of the vortex dictates the increase in lift behavior. Vortex shedding past the training edge decreases the lift. It is not clear what is the mechanism associated with the unsteady separation and vortex formation in present unsteady environment. To develop any flow control device, to suppress the vortex formation or delay separation, it is important that this mechanism be properly understood. The research activities directed toward understanding these questions are presented and the results are summarized.

Ahmed, Sajeer↗
DOE OSTI2024

Risk Considerations of Transitioning CO2-EOR Field to CO2 storage Field: Case Study

In the United States (U.S.), carbon dioxide (CO2) injection wells at EOR sites are currently regulated as Class II wells under the U.S. Environmental Protection Agency’s (EPA) Underground Injection Control (UIC) program while dedicated geological CO2 storage (GCS) wells are considered Class VI wells. A CO2-EOR facility considering a transitioning from tertiary oil recovery to injecting CO2 for the primary purpose of long-term storage is required to obtain a Class VI permit where this transition poses an increased risk to underground sources of drinking water. This study considers how transitioning operations from CO2-EOR to storage can impact reservoir plume and pressure transient in the storage envelope, and how these changes could impact area of review and potential unwanted fluid migration. We developed a case study to assess subsurface response and leakage risks associated with a representative, hypothetical operation in a carbonate reservoir. This reservoir transitions from tertiary hydrocarbon recovery to dedicated GCS. Reservoir simulations were run for a set of credible CO2-EOR scenarios to estimate distributions of fluids phases and pressures throughout the model domain after CO2 flooding as well as forecasting the behavior of the reservoir after the transition to a dedicated storage phase. The evolutions from all simulated scenarios were used as the basis for leakage risk quantification using the National Risk Assessment Partnership’s Open-Source Integrated Assessment Model (NRAP-Open-IAM) with a novel reduced-order model to estimate time-dependent leakage of CO2, brine, and hydrocarbon fluids through potentially leaky wells. Results include a description of reservoir response, an estimate of the areal extent that could potentially be impacted by leakage to underground sources of drinking water, and estimates of the magnitude of potential leakage. Considerations for dedicated storage injection well selection, injectivity, and injection scheme performance and potential leakage risk are presented, with implications for risk assessment of well transition discussed. This study presents a risk-based workflow for the Class II to Class VI well transition. Integrating credible numerical simulation of viable CO2-EOR to dedicated CO2 storage with quantitative risk assessment tools, such as the NRAP-Open-IAM, will provide a valuable means to devise operational scenarios and inform decision-making related to storage benefit, leakage risk, and liability. Presented at the SPE/AAPG/SEG Carbon Capture Utilization and Storage Conference in Houston, TX, March 11-13, 2024.

Liu, Guoxiang↗
NASA NTRS2015

In-Flight Aeroelastic Stability of the Thermal Protection System on the NASA HIAD, Part II: Nonlinear Theory and Extended Aerodynamics

Conical shell theory and a supersonic potential flow aerodynamic theory are used to study the nonlinear pressure buckling and aeroelastic limit cycle behavior of the thermal protection system for NASA's Hypersonic Inflatable Aerodynamic Decelerator. The structural model of the thermal protection system consists of an orthotropic conical shell of the Donnell type, resting on several circumferential elastic supports. Classical Piston Theory is used initially for the aerodynamic pressure, but was found to be insufficient at low supersonic Mach numbers. Transform methods are applied to the convected wave equation for potential flow, and a time-dependent aerodynamic pressure correction factor is obtained. The Lagrangian of the shell system is formulated in terms of the generalized coordinates for all displacements and the Rayleigh-Ritz method is used to derive the governing differential-algebraic equations of motion. Aeroelastic limit cycle oscillations and buckling deformations are calculated in the time domain using a Runge-Kutta method in MATLAB. Three conical shell geometries were considered in the present analysis: a 3-meter diameter 70 deg. cone, a 3.7-meter 70 deg. cone, and a 6-meter diameter 70 deg. cone. The 6-meter configuration was loaded statically and the results were compared with an experimental load test of a 6-meter HIAD. Though agreement between theoretical and experimental strains was poor, the circumferential wrinkling phenomena observed during the experiments was captured by the theory and axial deformations were qualitatively similar in shape. With Piston Theory aerodynamics, the nonlinear flutter dynamic pressures of the 3-meter configuration were in agreement with the values calculated using linear theory, and the limit cycle amplitudes were generally on the order of the shell thickness. The effect of axial tension was studied for this configuration, and increasing tension was found to decrease the limit cycle amplitudes when the circumferential elastic supports were neglected, but resulted in more complex behavior when the supports were included. The nominal flutter dynamic pressure of the 3.7-meter configuration was significantly lower than that of the 3-meter, and it was found that two sets of natural modes coalesce to flutter modes near the same dynamic pressure. This resulted in a significant drop in the limit cycle frequencies at higher dynamic pressures, where the flutter mode with the lower frequency becomes more critical. Pre-buckling pressure loads and the aerodynamic pressure correction factor were studied for all geometries, and these effects resulted in significantly lower flutter boundaries compared with Piston Theory alone. The maximum dynamic pressure predicted by aerodynamic simulations of a proposed 3.7-meter HIAD vehicle was still lower than any of the calculated flutter dynamic pressures, suggesting that aeroelastic effects for this vehicle are of little concern.

Goldman, Benjamin D.↗
DOE OSTI2022

Fluid and hybrid simulations of the ionization instabilities in Hall thruster

Low-frequency axial oscillations in the range of 5–50 kHz stand out as a pervasive feature observed in many types of Hall thrusters. While it is widely recognized that the ionization effects play the central role in this mode, as manifested via the large-scale oscillations of neutral and plasma density, the exact mechanism(s) of the instabilities remain unclear. To gain further insight into the physics of the breathing mode and evaluate the role of kinetic effects, a one-dimensional time-dependent full nonlinear low-frequency model describing neutral atoms, ions, and electrons is developed in full fluid formulation and compared to the hybrid model in which the ions and neutrals are kinetic. Both models are quasi-neutral and share the same electron fluid equations that include the electron diffusion, mobility across the magnetic field, and the electron energy evolution. The ionization models are also similar in both approaches. Further, the predictions of fluid and hybrid simulations are compared for different test cases. Two main regimes are identified in both models: one with pure low-frequency behavior and the other one, where the low-frequency oscillations coexist with high-frequency oscillations in the range of 100–200 kHz, with the characteristic time scale of the ion channel fly-by time, 100–200 kHz. The other test case demonstrates the effect of a finite temperature of injected neutral atoms, which has a substantial suppression effect on the oscillation amplitude.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

An experimental comparison of a space-time multigrid method with PFASST for a reaction-diffusion problem

We consider two parallel-in-time approaches applied to a (reaction) diffusion problem, possibly non-linear. In particular, we consider PFASST (Parallel Full Approximation Scheme in Space and Time) and space-time multigrid strategies. For both approaches, we start from an integral formulation of the continuous time dependent problem. Then, a collocation form for PFASST and a discontinuous Galerkin discretization in time for the space-time multi-grid are employed, resulting in the same discrete solution at the time nodes. Strong and weak scaling of both multilevel strategies are compared for varying orders of the temporal discretization. Moreover, we investigate the respective convergence behavior for non-linear problems and highlight quantitative differences in execution times

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Probing Operando Electrochemical Strain Generation in α-NaFeO 2 Composite Cathodes during Cycling of Na-Ion Batteries

The transition metal oxide (TMO) cathodes in Na-ion batteries suffer from low-capacity retention. Chemo-mechanical instabilities lead to the deterioration of the electrochemical performance of TMO cathodes in Li-ion batteries. However, there is not much known about the chemo-mechanical instabilities in the TMO cathodes for Na-ion batteries. Understanding the governing forces behind the interplay between the electrochemical performance and mechanical stability in TMO cathodes is critical for the development of Na-ion batteries. Here, we synchronize the digital image correlation (DIC) technique with electrochemical analysis to capture the real-time deformation behavior of the α-NaFeO 2 cathodes during cycling. When the charge cutoff voltage is 3.6 V, the cathode experiences reversible deformations (except for the first cycle). There is negative strain (shrinkage) generation during Na extraction and positive strain (expansion) generation during the subsequent Na insertion. A detailed analysis of the potential-dependent strain rate evolution points out complicated phase transformations and nonequilibrium conditions in the α-NaFeO 2 cathodes during cycling. When the charge cutoff voltage was increased to 4.2 V, there was a rapid capacity loss and large plastic deformations in the α-NaFeO 2 cathodes. We provide an in-depth discussion about the possible mechanisms behind the chemo-mechanical instabilities in the α-NaFeO 2 . In conclusion, the correlation is critical to develop material-based strategies to mitigate instability mechanisms in TMO cathodes for Na-ion batteries.

Wable, Minal [University of Maryland Baltimore Cou↗
DOE OSTI2023

The Stability Transition From Stable to Unstable Frictional Slip With Finite Pore Pressure

Pore fluids are ubiquitous throughout the lithosphere and are commonly invoked as the cause of induced seismicity and slow earthquakes. We perform lab experiments to address these questions for drained fault conditions and low pore pressure. We shear simulated faults at effective normal stress (σ' n ) of 20 MPa and pore pressures Pp from 1 to 4 MPa. We document the full range of lab earthquake behaviors from slow slip to elasto-dynamic rupture and show that slow slip can be explained by the slip rate dependence of the critical rheologic stiffness without dilatancy hardening or other fluid effects. Our fault permeabilities ranges from 10 –18 to 10 –17 m 2 with an initial porosity of 0.1 and estimated fluid diffusion time ≈1 s. Slow slip and quasi-dynamic fault motion may arise from high P p at higher pressures but dilatancy strengthening is not a general requirement.

58 GEOSCIENCES↗
DOE OSTI2026

Mapping Critical Vulnerabilities in Natural Gas Pipeline Systems through Network Centrality and GIS Analytics

Natural gas plays a central role in the US energy landscape, providing 43% of electricity generation in 2023. Its exclusive recovery ability on pipelines for transmission underscores the importance of understanding the disruption recovery ability of this infrastructure. This study employs a network-based analytical framework integrating geographic information systems (GIS) with multiple centrality measures—betweenness, closeness, degree, and eigenvector—to pinpoint key segments and evaluate the structural robustness of the national pipeline network. Pipelines are grouped by System ID and Operator ID to capture variations across organizational and physical structures. The analysis reveals uneven patterns of network influence, where certain pipelines function as critical connectors or dominant hubs. Spatial mapping highlights geographic dependencies and potential chokepoints, offering a clear view of where targeted risk prevention measures would be most effective. The findings provide practical guidance for prioritizing maintenance, enhancing system robustness, and mitigating risks to ensure a stable and secure energy supply. Future research will expand the framework to incorporate dynamic operational data and real-time network behavior.

Peterson, Steven [ORNL] (ORCID:0000000287672998)↗
DOE OSTI2019

Dynamic spin localization and γ -magnets

Here, we explore an unusual type of quantum matter that can be realized by qubits having different physical origins. Interactions in this matter are described by essentially different coupling operators for all qubits. We show that the simplest such models, which can be realized with localized states in Dirac materials, satisfy integrability conditions that we use to describe pseudospin dynamics in a linearly time-dependent magnetic field. Generalizing to an arbitrary number of qubits, we construct a spin Hamiltonian, which we call the γ -magnet. This system does not conserve polarization of any spin and the net spin polarization. Nevertheless, for arbitrarily strong interactions, nonadiabatic dynamics, and any initial eigenstate, we find that quantum interference suppresses spin flips. This behavior resembles many-body localization but occurs in phase space of many spins rather than real space. This effect may not have a counterpart in classical physics and can be a signature of a new type of spin ordering, which is different from both disordered spin glasses and ordered phases of spin lattices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Anomalous superconducting diode effect in a polar superconductor

A superconductor with broken time-reversal and inversion symmetry may exhibit nonreciprocal charge transport, including a nonreciprocal critical current, also known as superconducting diode effect. Here, we report an intrinsic superconducting diode effect in a polar strontium titanate film. Differential resistance measurements reveal a superconducting state whose depairing current is polarity dependent. There is, however, no measurable deviation from Ohmic behavior, implying that this state does not arise from a bulk magnetochiral anisotropy. In the entire measurement range, the only deviation from linearity in the differential resistance is on the edge of the superconducting transition at high magnetic fields, likely due to the motion of flux vortices. Furthermore, the magnitude of the effect is preserved even when the in-plane magnetic field is oriented parallel to the current, indicating that this effect truly does not originate from a bulk magnetochiral anisotropy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1981

Rotation of dwarf star chromospheres in the ultraviolet

Periodic variations in the ultraviolet fluxes of chromospheric emission line multiplets are investigated for F, G and K stars as evidence of rotational modulation. Vacuum ultraviolet spectra were obtained with the IUE spacecraft for six stars as many as 11 times over the period April 23 to December 3, 1980. Variations in the emission fluxes of the hydrogen Lyman-alpha, Si II and Mg II lines are observed with periods up to 47 days. The periodicity, which is identified with rotational modulation, is found to persist over many rotational cycles, although the periods and time dependences of the fluxes from the different ionic species are not identical, probably due to differential rotation and global distributions. The spread of the UV periods is observed to be within 10%, with one or two peaks per cycle and a ratio of modulated to umodulated flux ranging from 1.1 to 3.0, analogous to solar behavior.

Hallam, K. L.↗
NASA NTRS1985

Coupling of newborn ions to the solar wind by electromagnetic instabilities and their interaction with the bow shock

The process by which the solar wind assimilates newly ionized atoms is important for understanding the presence of planetary or interstellar helium in the solar wind, the dynamics of the Active Magnetospheric Particle Tracer Explorers (AMPTE) lithium releases in front of the earth's bow shock, and the formation of cometary tails. In this paper is examined how newborn ions can be coupled to the solar wind in the direction parallel to the magnetic field by means of electromagnetic instabilities driven by the distribution of newborn ions. The linear properties of three instabilities are analyzed and compared with numerical solutions of the linear dispersion equation, while their nonlinear behavior is followed by means of computer simulation to obtain the characteristic time for the pickup process. With a primary emphasis on the AMPTE lithiuim releases, various degrees of realism are introduced into the calculations to model the upstream conditions and the intersection of the lithium with the bow shock. It is shown that a time-dependent shock model is needed to correctly reproduce the amount of lithium which is transmitted through the shock and that the resulting lithium ion distribution is still likely to be subject to the same type of instabilities in the magnetosheath. Applications of these results to comets, in particular the artificial comet expected to be generated by the AMPTE barium release in the magnetosheath, is also briefly discussed.

Winske, D.↗
NASA NTRS1997

Mass Spectrometric Identification of Si-O-H(g) Species from the Reaction of Silica with Water Vapor at Atmospheric Pressure

A high-pressure sampling mass spectrometer was used to detect the volatile species formed from SiO2 at temperatures between 1200C and 1400C in a flowing water vapor/oxygen gas mixture at 1 bar total pressure. The primary vapor species identified was Si(OH)4. The fragment ion Si(OH)3+,' was observed in quantities 3 to 5 times larger than the parent ion Si(OH)4+. The Si(OH)3+ intensity was found to have a small temperature dependence and to increase with the water vapor partial pressure as expected. In addition, SiO(OH)+ believed to be a fragment of SiO(OH)2, was observed. These mass spectral results were compared to the behavior of silicon halides.

Opila, Elizabeth J.↗