Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “speed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Hydrogen test of a small, low specific speed centrifugal pump stage

A small, low specific speed centrifugal pump stage with a 2 inch tip diameter, .030 inch tip width shrouded impeller and volute collector was tested with liquid hydrogen as the pumped fluid. The hydrodynamic design of the pump stage is summarized and the noncavitating and cavitating performance results are presented. Test speeds were 60 and 80 percent of the 77,000 rpm design speed. Liquid hydrogen test results are compared with data from previous tests of the stage in water.

Source record↗
NASA NTRS1990

Some comparisons of linear stability theory with experiment at supersonic and hypersonic speed

Measurements of waves initiated by wind-tunnel sounds are obtained for both supersonic and hypersonic speed. Flat-plate experiments carried out at Mach numbers of 4.5, 3.7, and 2.4 under the condition of laminar tunnel-wall boundary layers whereby a low background fluctuation level prevailed are outlined, as well as flat-plate experiments with sound-induced waves at supersonic speeds. Experimental studies of 'natural' wave growth on sharp cones at zero angle of attack and Mach numbers near 8 are discussed. Attention is focused on experimental research needed on boundary-layer receptivity to eddy Mach-wave radiation, hypersonic speed, and the stability-transition relationship in zero-pressure-gradient layers.

Kendall, James M., Jr.↗
NASA NTRS1991

Effects of oscillatory speed and mutual overlap on the tribological behavior of PTFE and selected PTFE-based self-lubricating composites

The wear reducing actions of bronze, graphic powder and discontinuous glass fiber within a PTFE matrix have been demonstrated in oscillatory contact with stainless steel, at two different amplitudes, over a range of speeds. The secondary effects on the friction of the PTFE have also been investigated. The effects of oscillation amplitude on frictional surface morphology have been observed for these composites. The friction and wear of the unfilled PTFE matrix were both found to increase as speed increased, with wear going through a transition from a low- to high-rate regime. The speed at which this transition occurs increases with decreasing oscillatory amplitude.

Blanchet, Thierry A.↗
NASA NTRS1991

Overview of airframe technology in the NASA High-Speed Research Program

NASA's Phase I High-Speed Research Program has been established to develop solutions for critical environmental issues confronting the next-generation U.S. SST, or High-Speed Civil Transport (HSCT). Attention is presently given to the ways in which HSCT environmental acceptability is affected by such airframe-technology features as laminar flow control, advanced high-lift systems for TO&L, and contour tailoring for sonic-boom minimization. The reduction of sonic booms is economically critical to the HSCT, in that it will permit overland flight at supersonic speeds and therefore maximize the reduction in long-range flight times.

Whitehead, Allen H., Jr.↗
NASA NTRS1990

NASA Langley and AF RADC high-speed fiber optic transceiver program

NASA-Langley and the USAF Rome Air Development Center have been pursuing the development of military- and space-qualified fiber optic transceivers for a variety of ground-based, space-based, and general avionic applications. An initial development pursued a design called the multipurpose fiber optic transceiver (MFOX) and provided a family of fiber optic transceivers which operated up to 1 Gb/s. Currently, a second generation of high-speed fiber optic transceivers (HSFOX) is being developed. This design will utilize an all-integrated-circuits approach in order to develop a lighter-weight, smaller-size, and more efficient transceiver. The high-speed fiber optic transceiver will be military-and-space-operating in the 0.05-5 Gb/s data rate range. The initial results of tests, performance, and availability of commercial high-speed all-integrated-circuit chipsets for fiber-optic transceivers are discussed, as well as the performance of transceivers fabricated from these chipsets.

Hendricks, Herbert D.↗
NASA NTRS1991

Technology needs for high speed rotorcraft (3)

The spectrum of vertical takeoff and landing (VTOL) type aircraft is examined to determine which aircraft are most likely to achieve high subsonic cruise speeds and have hover qualities similar to a helicopter. Two civil mission profiles are considered: a 600-n.mi. mission for a 15- and a 30-passenger payload. Applying current technology, only the 15- and 30-passenger tiltfold aircraft are capable of attaining the 450-knot design goal. The two tiltfold aircraft at 450 knots and a 30-passenger tiltrotor at 375 knots were further developed for the Task II technology analysis. A program called High-Speed Total Envelope Proprotor (HI-STEP) is recommended to meet several of these issues based on the tiltrotor concept. A program called Tiltfold System (TFS) is recommended based on the tiltrotor concept. A task is identified to resolve the best design speed from productivity and demand considerations based on the technology that emerges from the recommended programs. HI-STEP's goals are to investigate propulsive efficiency, maneuver loads, and aeroelastic stability. Programs currently in progress that may meet the other technology needs include the Integrated High Performance Turbine Engine Technology (IHPTET) (NASA Lewis) and the Advanced Structural Concepts Program funded through NASA Langley.

Detore, Jack↗
NASA NTRS1992

High-speed Civil Transport Aircraft Emissions

Estimates are given for the emissions from a proposed high speed civil transport (HSCT). This advanced technology supersonic aircraft would fly in the lower stratosphere at a speed of roughly Mach 1.6 to 3.2 (470 to 950 m/sec or 920 to 1850 knots). Because it would fly in the stratosphere at an altitude in the range of 15 to 23 km commensurate with its design speed, its exhaust effluents could perturb the chemical balance in the upper atmosphere. The first step in determining the nature and magnitude of any chemical changes in the atmosphere resulting from these proposed aircraft is to identify and quantify the chemically important species they emit. Relevant earlier work is summarized, dating back to the Climatic Impact Assessment Program of the early 1970s and current propulsion research efforts. Estimates are provided of the chemical composition of an HSCT's exhaust, and these emission indices are presented. Other aircraft emissions that are not due to combustion processes are also summarized; these emissions are found to be much smaller than the exhaust emissions. Future advances in propulsion technology, in experimental measurement techniques, and in understanding upper atmospheric chemistry may affect these estimates of the amounts of trace exhaust species or their relative importance.

Miake-Lye, Richard C.↗
NASA NTRS1990

High speed turboprop aeroacoustic study (counterrotation). Volume 2: Computer programs

The isolated counterrotating high speed turboprop noise prediction program developed and funded by GE Aircraft Engines was compared with model data taken in the GE Aircraft Engines Cell 41 anechoic facility, the Boeing Transonic Wind Tunnel, and in the NASA-Lewis 8 x 6 and 9 x 15 wind tunnels. The predictions show good agreement with measured data under both low and high speed simulated flight conditions. The installation effect model developed for single rotation, high speed turboprops was extended to include counter rotation. The additional effect of mounting a pylon upstream of the forward rotor was included in the flow field modeling. A nontraditional mechanism concerning the acoustic radiation from a propeller at angle of attack was investigated. Predictions made using this approach show results that are in much closer agreement with measurement over a range of operating conditions than those obtained via traditional fluctuating force methods. The isolated rotors and installation effects models were combined into a single prediction program. The results were compared with data taken during the flight test of the B727/UDF (trademark) engine demonstrator aircraft.

Whitfield, C. E.↗
NASA NTRS1992

Design and analysis issues of integrated control systems for high-speed civil transports

A study was conducted to identify, rank, and define development plans for the critical guidance and control design and analysis issues as related to economically viable and environmentally acceptable high-speed civil transport. The issues were identified in a multistep process. First, pertinent literature on supersonic cruise aircraft was reviewed, and experts were consulted to establish the fundamental characteristics and problems inherent to supersonic cruise aircraft. Next, the advanced technologies and strategies being pursued for the high-speed civil transport were considered to determine any additional unique control problems the transport may have. Finally, existing technologies and methods were examined to determine their capabilities for the design and analysis of high-speed civil transport control systems and to identify the shortcomings and issues. Three priority levels - mandatory, highly beneficial, and desirable - were established. Within each of these levels, the issues were further ranked. Technology development plans for each issue were defined. Each plan contains a task breakdown and schedule.

Mccarty, Craig A.↗
NASA NTRS1991

High speed rotorcraft - Comparison of leading concepts and technology needs

Design studies have recently been completed by Bell, Boeing, McDonnell Douglas and Sikorsky with the goal of identifying technology needs of high speed rotorcraft concepts. The general study guidelines were for 450-kt cruise speeds and low downwash characteristics. These concepts included the the folding tiltrotor, the high speed tiltrotor, the variable diameter tiltrotor, a tip-drive stopped rotor and the tilt wing. The studies have also identified technology needs of these concepts with the objective of defining a systematic program of technology development to increase confidence in the subsystems and components and achieving a low-risk design capability in the year 2000. Each contractor has reported independently on his efforts. This paper is a survey of the contractor efforts taken together, with regard to concepts, selection methods, technical issues (common and critical technologies), technology benefits and the technology plan recommendations.

Talbot, Peter D.↗
NASA NTRS1991

NASA low-speed centrifugal compressor for 3-D viscous code assessment and fundamental flow physics research

A low speed centrifugal compressor facility recently built by the NASA Lewis Research Center is described. The purpose of this facility is to obtain detailed flow field measurements for computational fluid dynamic code assessment and flow physics modeling in support of Army and NASA efforts to advance small gas turbine engine technology. The facility is heavily instrumented with pressure and temperature probes, both in the stationary and rotating frames of reference, and has provisions for flow visualization and laser velocimetry. The facility will accommodate rotational speeds to 2400 rpm and is rated at pressures to 1.25 atm. The initial compressor stage being tested is geometrically and dynamically representative of modern high-performance centrifugal compressor stages with the exception of Mach number levels. Preliminary experimental investigations of inlet and exit flow uniformly and measurement repeatability are presented. These results demonstrate the high quality of the data which may be expected from this facility. The significance of synergism between computational fluid dynamic analysis and experimentation throughout the development of the low speed centrifugal compressor facility is demonstrated.

Hathaway, M. D.↗
NASA NTRS1992

Turbulence modeling for high speed flows

An investigation of turbulence models for high speed flows is presented. The flows consist of simple 2D flows over flat plates and complex shock-wave boundary-layer interaction flows over ramps and wedges. The flows are typical of those encountered by high speed vehicles such as the NASP. The turbulence models investigated include various two-equation models which, as a class, are considered to be well suited to the design of high speed vehicles. A description and discussion of the specific models is given and includes both baseline or uncorrected models, and model corrections which are needed to improve predictions of complex flows. It is found that most of the models studied are able to give good predictions of the flat plate flows, and some of the models are able to predict some of the complex flows, but none of them are able to accurately predict all of the complex flows. Recommendations for future model improvements are discussed.

Coakley, T. J.↗
NASA NTRS1992

Control of low-speed turbulent separated flow using jet vortex generators

A parametric study has been performed with jet vortex generators to determine their effectiveness in controlling flow separation associated with low-speed turbulent flow over a two-dimensional rearward-facing ramp. Results indicate that flow-separation control can be accomplished, with the level of control achieved being a function of jet speed, jet orientation (with respect to the free-stream direction, and jet location (distance from the separation region in the free-stream direction). Compared to slot blowing, jet vortex generators can provide an equivalent level of flow control over a larger spanwise region (for constant jet flow area and speed).

Selby, G. V.↗
NASA NTRS1992

Comparison of wind speed measurements over the oceans with the Special Sensor Microwave/Imager and the Geosat altimeter

In order to compare wind speed estimates from the Geosat altimeter and the Special Sensor Microwave/Imager (SSM/I), 25 colocated passes, within 2 hours of each other, were selected and the SSM/I estimates of wind speed and atmospheric parameters extracted along the Geosat track. Both instruments and their algorithms are described. A statistical comparison of wind speed estimates is presented and the effects of the atmospheric parameters from Geosat are analyzed. Quasi-simultaneous measurements by Geosat and SSM/I, along a Geosat track in the North-East Pacific, are also presented.

Mognard, Nelly M.↗
NASA NTRS1992

Low-speed longitudinal and lateral-directional aerodynamic characteristics of the X-31 configuration

An experimental investigation of a 19 pct. scale model of the X-31 configuration was completed in the Langley 14 x 22 Foot Subsonic Tunnel. This study was performed to determine the static low speed aerodynamic characteristics of the basic configuration over a large range of angle of attack and sideslip and to study the effects of strakes, leading-edge extensions (wing-body strakes), nose booms, speed-brake deployment, and inlet configurations. The ultimate purpose was to optimize the configuration for high angle of attack and maneuvering-flight conditions. The model was tested at angles of attack from -5 to 67 deg and at sideslip angles from -16 to 16 deg for speeds up to 190 knots (dynamic pressure of 120 psf).

Banks, Daniel W.↗
NASA NTRS1992

High-speed architecture for the decoding of trellis-coded modulation

Since 1971, when the Viterbi Algorithm was introduced as the optimal method of decoding convolutional codes, improvements in circuit technology, especially VLSI, have steadily increased its speed and practicality. Trellis-Coded Modulation (TCM) combines convolutional coding with higher level modulation (non-binary source alphabet) to provide forward error correction and spectral efficiency. For binary codes, the current stare-of-the-art is a 64-state Viterbi decoder on a single CMOS chip, operating at a data rate of 25 Mbps. Recently, there has been an interest in increasing the speed of the Viterbi Algorithm by improving the decoder architecture, or by reducing the algorithm itself. Designs employing new architectural techniques are now in existence, however these techniques are currently applied to simpler binary codes, not to TCM. The purpose of this report is to discuss TCM architectural considerations in general, and to present the design, at the logic gate level, or a specific TCM decoder which applies these considerations to achieve high-speed decoding.

Osborne, William P.↗
NASA NTRS1993

Preconditioned conjugate-gradient methods for low-speed flow calculations

An investigation is conducted into the viability of using a generalized Conjugate Gradient-like method as an iterative solver to obtain steady-state solutions of very low-speed fluid flow problems. Low-speed flow at Mach 0.1 over a backward-facing step is chosen as a representative test problem. The unsteady form of the two dimensional, compressible Navier-Stokes equations is integrated in time using discrete time-steps. The Navier-Stokes equations are cast in an implicit, upwind finite-volume, flux split formulation. The new iterative solver is used to solve a linear system of equations at each step of the time-integration. Preconditioning techniques are used with the new solver to enhance the stability and convergence rate of the solver and are found to be critical to the overall success of the solver. A study of various preconditioners reveals that a preconditioner based on the Lower-Upper Successive Symmetric Over-Relaxation iterative scheme is more efficient than a preconditioner based on Incomplete L-U factorizations of the iteration matrix. The performance of the new preconditioned solver is compared with a conventional Line Gauss-Seidel Relaxation (LGSR) solver. Overall speed-up factors of 28 (in terms of global time-steps required to converge to a steady-state solution) and 20 (in terms of total CPU time on one processor of a CRAY-YMP) are found in favor of the new preconditioned solver, when compared with the LGSR solver.

Ajmani, Kumud↗
NASA NTRS1992

MM-122: High speed civil transport

The rapidly expanding Pacific Rim market along with other growing markets indicates that the future market potential for a high speed civil transport is great indeed. The MM-122 is the answer to the international market desire for a state of the art, long range, high speed civil transport. It will carry 250 passengers a distance of 5200 nm at over twice the speed of sound. The MM-122 is designed to incorporate the latest technologies in the areas of control systems, propulsions, aerodynamics, and materials. The MM-122 will accomplish these goals using the following design parameters. First, a double delta wing planform with highly swept canards and an appropriately area ruled fuselage will be incorporated to accomplish desired aerodynamic characteristics. Propulsion will be provided by four low bypass variable cycle turbofan engines. A quad-redundant fly-by-wire flight control system will be incorporated to provide appropriate static stability and level 1 handling qualities. Finally, the latest in conventional metallic and modern composite materials will be used to provide desired weight and performance characteristics. The MM-122 incorporates the latest in technology and cost minimization techniques to provide a viable solution to this future market potential.

Demarest, Bill↗