Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “regularity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Acceleration display system for aircraft zero-gravity research

The features, design, calibration, and testing of Lewis Research Center's acceleration display system for aircraft zero-gravity research are described. Specific circuit schematics and system specifications are included as well as representative data traces from flown trajectories. Other observations learned from developing and using this system are mentioned where appropriate. The system, now a permanent part of the Lewis Learjet zero-gravity program, provides legible, concise, and necessary guidance information enabling pilots to routinely fly accurate zero-gravity trajectories. Regular use of this system resulted in improvements of the Learjet zero-gravity flight techniques, including a technique to minimize later accelerations. Lewis Gates Learjet trajectory data show that accelerations can be reliably sustained within 0.01 g for 5 consecutive seconds, within 0.02 g for 7 consecutive seconds, and within 0.04 g for up to 20 second. Lewis followed the past practices of acceleration measurement, yet focussed on the acceleration displays. Refinements based on flight experience included evolving the ranges, resolutions, and frequency responses to fit the pilot and the Learjet responses.

Millis, Marc G.↗

IUE observations of Comet Halley: Evolution of the UV spectrum between September 1985 and June 1986

The UV spectrum of comet P/Halley (1982 i) was monitored with the IUE at regular time intervals. A complete characterization of the UV spectrum of the comet was obtained to derive coma abundances and to study the light emission mechanisms of the observed species. The Fine Error Sensor (FES) camera of the IUE was used to investigate the coma brightness variability on short time scales. Spectroscopic observations as well as FES measurements show that the comet nucleus activity was highly variable.

Feldman, P. D.↗

Large manned systems/environment interactions in Low Earth Orbit (LEO)

With the advent of the NASA Space Transportation System, regular flights of a large manned spacecraft, the Space Shuttle Orbiter, became a reality. From the earliest mission containing space science instruments as a payload on the third flight of the Orbiter (STS-3), it became apparent that the disturbance caused by the interaction of this orbiting system with the low Earth orbit (LEO) environment resulted in adverse conditions for the performance of scientific observations of the Orbiter natural environment and for certain high sensitivity optical observations. The interaction of the Space Shuttle Orbiter system can be divided into two parts, the structure-environment interaction, and the outgas cloud-environment interaction. These interaction are briefly discussed.

Raitt, W. J.↗

Effects of space shuttle launches STS-1 through STS-9 on terrestrial vegetation of John F. Kennedy Space Center, Florida

Space Shuttle launches produce a cloud containing hydrochloric acid (HCl), aluminum oxide (Al203), and other substances. Acidities of less than 0.5 pH have been measured routinely in association with the launch cloud. In an area of about 22 ha regularly exposed to the exhaust cloud during most Shuttle launches, acute vegetation damage has resulted from the first nine Shuttle launches. Changes include loss of sensitive species, loss of plant community structure, reduction in total cover, and replacement of some species by weedy invaders. Community level changes define a retrogressive sequence. One-time impacts to strand and dune vegetation occurred after launches of STS-8 and STS-9. Acute vegetation damage occurred especially to sensitive species. Within six months, however, recovery was nearly complete. Sensitivity of species to the launch cloud was partially predicted by previous laboratory studies. Far-field acidic and dry fallout from the cloud as it rises to stabilization and moves with the prevailing winds causes vegetation spotting. Damage from this deposition is minor; typically at most 1% to 5% of leaf surface area is affected. No plant mortality or community changes have occurred from far-field deposition.

Schmalzer, P. A.↗

Soft X-ray oscillations during the flare of 7 August 1972

Unique observations from OSO-7 of the intense flare on 7 August 1972 are presented, showing 1.6 second oscillations in it's soft X-ray emission which are long enduring, extremely regular, and initially of large amplitude. For approximately 20 minutes just after flare maximum, the X-ray intensity of an area 20 arc second square near the flare's core was monitored with 160 millisecond time resolution in two channels, 2-8A and 8-16A. Each channel recorded over 700 cycles of the X-ray oscillations, which remained remarkably stable in phase and period throughout the entire observations, but with gradually diminishing amplitude. The observed period does not correspond to any known operational periodicity in either the instrument or the spacecraft and cannot be attributed to aliasing with any other oscillatory component. Channel ratios indicate that both the temperature and electron density of the emitting plasma are enhanced at the peak of each cycle. There is indirect evidence that the X-ray pulsations are occurring only in a relatively small portion of an elongated feature, presumed to be a loop or arcade of loops.

Thomas, Roger J.↗

Chandrasekhar equations for infinite dimensional systems. Part 2: Unbounded input and output case

A set of equations known as Chandrasekhar equations arising in the linear quadratic optimal control problem is considered. In this paper, we consider the linear time-invariant system defined in Hilbert spaces involving unbounded input and output operators. For a general class of such systems, the Chandrasekhar equations are derived and the existence, uniqueness, and regularity of the results of their solutions established.

Ito, Kazufumi↗

Studies of fluid instabilities in flows of lava and debris

At least two instabilities have been identified and utilized in lava flow studies: surface folding and gravity instability. Both lead to the development of regularly spaced structures on the surfaces of lava flows. The geometry of surface folds have been used to estimate the rheology of lava flows on other planets. One investigation's analysis assumed that lava flows have a temperature-dependent Newtonian rheology, and that the lava's viscosity decreased exponentially inward from the upper surface. The author reviews studies by other investigators on the analysis of surface folding, the analysis of Taylor instability in lava flows, and the effect of surface folding on debris flows.

Fink, Jonathan H.↗

Lithospheric loading and tectonics of the lunar irregular maria

Many of the tectonic features associated with the circular maria are the result of stresses generated by loading of the lunar lithosphere by mare basalt units. The hypothesis is tested that the irregular lunar maria share with the circular maria the processes leading to the formation of associated graben and mare ridge systems. A formulation of the lithospheric flexure problem that accounts for the variable distribution of basalt loads for the irregular maria is applied. On the basis of the tectonic structures and geologic history of each of the major irregular maria, as well as models for the distribution of mare basalt for each region, the predicted stress fields are compared with the distribution of tectonic features for a range of assumed values of the thickness of the elastic lithosphere. The best fitting values for lithospheric thickness beneath the regular maria are then compared with those previously inferred for the circular maria.

Hall, J. Lynn↗

Infrared properties of dust grains derived from IRAS observations

The analysis of several diffuse interstellar clouds observed by the Infrared Astronomy Satellite (IRAS) is presented. The 60/100 micron flux ratios appear to be nearly constant in clouds with up to 1 sup m visual extinction at the center. Observations of a highly regular cloud in Chamaeleon show that the 12/100 micron ratio peaks at an intermediate radial distance and declines towards the center of the cloud. These observations indicate that nonequilibrium emission accounts only for the 12 and 25 micron bands; strong emission observed at the 60 micron band is probably due to equilibrium thermal radiation. The correlation of the 12 micron emission with a red excess observed for a high latitude cloud, L1780, is shown to be consistent with the assumption that both features are due to fluorescence by the same molecular species.

Chlewicki, G.↗

IUE observations of Comet Halley: Evolution of the UV spectrum between September 1985 and July 1986

The ultraviolet spectrum of comet P/Halley was monitored with the IUE between 12 September 1985 and 8 July 1986 (r <2.6 AU pre and post-perihelion) at regular time intervals except for a two-month period around the time of perihelion. A complete characterization of the UV spectrum of the comet was obtained to derive coma abundances and to study the light emission mechanisms of the observed species. The Fine Error Sensor (FES) camera of the IUE was used to photometrically investigate the coma brightness variation on time scales of the order of hours. Spectroscopic observations as well as FES measurements show that the activity of the nucleus is highly variable, particularly at the end of December 1985 and during March and April 1986. The production rates of OH, CS and dust are derived for the entire period of the observations. The total water loss rate for this period is estimated to be 150 million metric tons.

Feldman, P. D.↗

Synthesis, physical and chemical properties, and potential applications of graphite fluoride fibers

Graphite fluoride fibers can be produced by fluorinating pristine or intercalated graphite fibers. The higher the degree of graphitization of the fibers, the higher the temperature needed to reach the same degree of fluorination. Pitched based fibers were fluorinated to flourine-to-carbon atom rations between 0 and 1. The graphite fluoride fibers with a fluorine-to-carbon atom ration near 1 have extensive visible structural damage. On the other hand, fluorination of fibers pretreated with bromine or fluorine and bromine result in fibers with a fluorine-to-carbon atom ratio nearly equal to 0.5 with no visible structural damage. The electrical resistivity of the fibers is dependent upon the fluorine to carbon atom ratio and ranged from .01 to 10 to the 11th ohm/cm. The thermal conductivity of these fibers ranged from 5 to 73 W/m-k, which is much larger than the thermal conductivity of glass, which is the regular filler in epoxy composites. If graphite fluoride fibers are used as a filler in epoxy or PTFE, the resulting composite may be a high thermal conductivity material with an electrical resistivity in either the insulator or semiconductor range. The electrically insulating product may provide heat transfer with lower temperature gradients than many current electrical insulators. Potential applications are presented.

Hung, Ching-Cheh↗

Synthetic aperture radar signal processing on the MPP

Satellite-borne Synthetic Aperture Radars (SAR) sense areas of several thousand square kilometers in seconds and transmit phase history signal data several tens of megabits per second. The Shuttle Imaging Radar-B (SIR-B) has a variable swath of 20 to 50 km and acquired data over 100 kms along track in about 13 seconds. With the simplification of separability of the reference function, the processing still requires considerable resources; high speed I/O, large memory and fast computation. Processing systems with regular hardware take hours to process one Seasat image and about one hour for a SIR-B image. Bringing this processing time closer to acquisition times requires an end-to-end system solution. For the purpose of demonstration, software was implemented on the present Massively Parallel Processor (MPP) configuration for processing Seasat and SIR-B data. The software takes advantage of the high processing speed offered by the MPP, the large Staging Buffer, and the high speed I/O between the MPP array unit and the Staging Buffer. It was found that with unoptimized Parallel Pascal code, the processing time on the MPP for a 4096 x 4096 sample subset of signal data ranges between 18 and 30.2 seconds depending on options.

Ramapriyan, H. K.↗

Multigrid methods for bifurcation problems: The self adjoint case

This paper deals with multigrid methods for computational problems that arise in the theory of bifurcation and is restricted to the self adjoint case. The basic problem is to solve for arcs of solutions, a task that is done successfully with an arc length continuation method. Other important issues are, for example, detecting and locating singular points as part of the continuation process, switching branches at bifurcation points, etc. Multigrid methods have been applied to continuation problems. These methods work well at regular points and at limit points, while they may encounter difficulties in the vicinity of bifurcation points. A new continuation method that is very efficient also near bifurcation points is presented here. The other issues mentioned above are also treated very efficiently with appropriate multigrid algorithms. For example, it is shown that limit points and bifurcation points can be solved for directly by a multigrid algorithm. Moreover, the algorithms presented here solve the corresponding problems in just a few work units (about 10 or less), where a work unit is the work involved in one local relaxation on the finest grid.

Taasan, Shlomo↗

Shape design sensitivity analysis using domain information

A numerical method for obtaining accurate shape design sensitivity information for built-up structures is developed and demonstrated through analysis of examples. The basic character of the finite element method, which gives more accurate domain information than boundary information, is utilized for shape design sensitivity improvement. A domain approach for shape design sensitivity analysis of built-up structures is derived using the material derivative idea of structural mechanics and the adjoint variable method of design sensitivity analysis. Velocity elements and B-spline curves are introduced to alleviate difficulties in generating domain velocity fields. The regularity requirements of the design velocity field are studied.

Seong, Hwal-Gyeong↗

A hybrid perturbation Galerkin technique with applications to slender body theory

A two step hybrid perturbation-Galerkin method to solve a variety of applied mathematics problems which involve a small parameter is presented. The method consists of: (1) the use of a regular or singular perturbation method to determine the asymptotic expansion of the solution in terms of the small parameter; (2) construction of an approximate solution in the form of a sum of the perturbation coefficient functions multiplied by (unknown) amplitudes (gauge functions); and (3) the use of the classical Bubnov-Galerkin method to determine these amplitudes. This hybrid method has the potential of overcoming some of the drawbacks of the perturbation method and the Bubnov-Galerkin method when they are applied by themselves, while combining some of the good features of both. The proposed method is applied to some singular perturbation problems in slender body theory. The results obtained from the hybrid method are compared with approximate solutions obtained by other methods, and the degree of applicability of the hybrid method to broader problem areas is discussed.

Geer, James F.↗

Computer architectures for computational physics work done by Computational Research and Technology Branch and Advanced Computational Concepts Group

Slides are reproduced that describe the importance of having high performance number crunching and graphics capability. They also indicate the types of research and development underway at Ames Research Center to ensure that, in the near term, Ames is a smart buyer and user, and in the long-term that Ames knows the best possible solutions for number crunching and graphics needs. The drivers for this research are real computational physics applications of interest to Ames and NASA. They are concerned with how to map the applications, and how to maximize the physics learned from the results of the calculations. The computer graphics activities are aimed at getting maximum information from the three-dimensional calculations by using the real time manipulation of three-dimensional data on the Silicon Graphics workstation. Work is underway on new algorithms that will permit the display of experimental results that are sparse and random, the same way that the dense and regular computed results are displayed.

Source record↗

Transonic flow visualization using holographic interferometry

An account is made of some of the applications of holographic interferometry to the visualization of transonic flows. In the case of the compressor shock visualization, the method is used regularly and has moved from being a research department invention to a design test tool. With the implementation of automatic processing and simple digitization systems, holographic vibrational analysis has also moved into routine nondestructive testing. The code verification interferograms were instructive, but the main turbomachinery interest is now in 3 dimensional flows. A major data interpretation effort will be required to compute tomographically the 3 dimensional flow around the leading or the trailing edges of a rotating blade row. The bolt on approach shows the potential application to current unsteady flows of interest. In particular that of the rotor passing and vortex interaction effects is experienced by the new generation of unducted fans. The turbocharger tests presents a new area for the application of holography.

Bryanston-Cross, Peter J.↗

In-flight assessment of workload using instrument scan

During instrument flight, the pilot obtains information concerning aircraft state by cross checking or scanning the flight instruments. The exact method of scanning the instrument panel varies from pilot to pilot but there are some basic features common to a good scan pattern. The method discussed may be considered a candidate for workload studies with piloting tasks which will invoke a regular visual scan (spatial/temporal pattern of eye movements) during instrument flight. It is important to point out that instrument scan by itself is not a complete indicator of workload nor is task attention necessarily associated with where the pilot happens to be looking at a particular instant. However, whenever instrument scan is required in a piloting task, analysis of scanning behavior may yield important direct or indirect information concerning workload.

Tole, J. R.↗