Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reactor type”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Novel Calibration Approach for Monitoring Aerosol Hydrogen Isotopes Using Laser-Induced Breakdown Spectroscopy for Molten Salt Reactor Off-Gas Streams

Online monitoring is a key challenge for the continued development of molten salt reactor (MSR) technology. Laser-induced breakdown spectroscopy (LIBS) has previously been demonstrated to be a viable tool for monitoring aerosolized species and noble gases in real time, but the ability to discern varying isotopes in these streams has not yet been investigated for MSR applications. Tritium will form in MSRs from ternary fission and from (n,α)-reactions occurring in lithium-containing salts. This study compares three spectrometers of varying resolutions and types for measuring hydrogen isotope shifts in LIBS spectra of wetted filter paper. For each spectrometer, multivariate models were built (i.e., principal component regression, partial least squares regression, and multivariate curve resolution) to quantify the isotope ratio. The top models were then modified and corrected to apply the models to aerosol samples with varying isotope ratios. This novel calibration strategy offers an 82% reduction in volume of the calibration samples needed and is a more viable pathway for calibrating deployable LIBS systems. Lastly, this calibration model was compared with an all-aerosol trained model for monitoring hydrogen isotopes during a real-time test where the protium/deuterium ratio, along with representative salt species (i.e., lithium, sodium, and potassium) were adjusted dynamically. Results of this test validated the predictive capabilities of the transferred model and highlighted the capabilities of LIBS for real-time monitoring of MSR effluent streams.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Non-destructive structural characterization of graphite components using mechanical resonance and deep learning

As compared to conventional nuclear reactors, microreactors have the potential to significantly reduce construction timelines and capital costs, decreasing the barriers for advanced nuclear reactor technologies. However, the lower power output of these microreactors (typically < 20 MWe) creates challenging economics if operation and maintenance costs cannot be sufficiently reduced. The compact size of these designs presents an opportunity for comprehensive in-situ structural health monitoring to provide real-time feedback in order to reduce operational costs associated with maintenance and downtime. Many microreactor concepts use graphite for both in-core neutron moderation and as a structural material, which has typically required some form of periodic and laborious inspection. This report provides a description and assessment of recent work with graphite to couple acoustic-based experimental measurements and characterization with machine learning models to mature structural health monitoring capabilities and generate benefits for the nuclear microreactor industry. With resilient embedded sensors in development in other programs funded by the US Department of Energy’s Office of Nuclear Energy and elsewhere, the work described herein builds upon previously funded efforts to mature non-destructive testing technology that relates measured vibrational signatures to structural changes, using a combination of new experimental measurements and machine learning processing. Building on past successful demonstrations of predictive workflows to identify structural changes in a hexagonal stainless steel test article with excellent acoustic propagation, we first performed baseline characterization on graphite samples with canonical geometries to ensure compatibility and confidence in the applied techniques for a material with distinctly different mechanical properties. In contrast to efforts in previous years, we worked exclusively with unidirectional vibration data that is more comparable to those expected from the existing embedded sensor technologies which are suitable for deployment in a reactor setting. Established acoustic and modern machine-learning-based characterization approaches were applied to the resulting datasets from these simple geometries. Both approaches were found to be highly capable of detecting even small geometric irregularities amongst nominally identical samples. As such, we then moved to testing these approaches for detection of artificial local stress perturbations introduced into a more complex geometry: a hexagonal block with drilled holes. A main outcome of this work is that a generalizable ML workflow can be used to detect and predict the characteristics of small artificial anomalies in a graphite component with a relevant geometry. While this work was performed using surficial vibration data, we expect the approach to be flexible and viable for other monitoring scenarios, such as those with different arrangements or types of sensor arrays. As compared to previously funded efforts, an existing ML workflow based on neural networks was enhanced through the addition of recently developed Fourier neural operators. As applied to previously collected and new vibration datasets, prediction accuracies of anomaly characterizations were greatly improved with minimal added computational cost. As trained on small durations of vibration data (tens of seconds) collected over a realistic number of locations, the model was able to reliably determine the presence of a subtle stress anomaly and begin to provide location estimates. Such an approach is likely to be viable for more relevant reactor damage scenarios for graphite components, such as progressive crack growth or creep.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Status Update for the Bearing Test Article Design Development – FY2025

Argonne National Laboratory’s (ANL) Mechanism Engineering Test Loop (METL) team has completed the design of a new Bearing Test Article (BTA) to test mechanical bearings for sodium fast reactor (SFR) mechanism applications. Recognition of the need for further bearing testing arose due to failure of rolling element bearings during testing of components for in-vessel fuel handling machines (FHMs) conducted at ANL in the METL facility. While the initial concept of the BTA arose from a need for bearing testing for FHM applications, the BTA design is configurable to test bearings of various sizes, types, and materials submerged in liquid sodium. Requirements for loading, shaft speed, temperature, and bearing size range were chosen based on requirements for SFR fuel handling. Modular components in the test bearing housings and shaft sleeves allow the design to accommodate a wide range of bearing sizes without modification to the larger assembly. Loading will be applied with screw jacks on the air side of the test article that will be adjusted to apply radial, thrust, or combined loading conditions. Applied force will be measured by load cells in-line with the loading mechanisms. In FY25 we have completed the design of the test article that will be fabricated and undergo testing at the METL facility. Drawing packages for the fabrication of the test article have been drafted and are being reviewed to add part tolerances and we have started ordering off-the-shelf components. The report will summarize the development of the Bearing Test Article design starting with an overview of the entire test article, then a more detailed examination of the bearing test section, loading mechanisms, test article ports and seals, and support structures, including analysis that went into significant design choices.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

$\mathrm{EBR-II MOX}$ Fuel Characterization Enabling ARES Phase I Testing

Pretransient characterization was performed for the Experimental Breeder Reactor II (EBR-II) mixed-oxide (MOX) fuel pellets from the SPA-2/-2B Operational Reliability Testing collaboration between Japan and the United States. Continued collaboration under the Advanced Reactor Experiments for Sodium Fast Reactor Fuels project will investigate the transient performance of these rods in the Transient Reactor Test facility at Idaho National Laboratory in the MOXTOP-THOR experiment. The results will fill a gap in existing transient performance data for MOX as these rods have a peak burnup of 14.3 at. % (~134.4 GWd/t) in the EBR-II. Fuel pellet properties were gathered from available resources and their irradiation and decay history evaluated. Further reactor physics calculations were performed to support the experiment design, reactor operations, and safety analyses necessary to enable the programmatic success of this effort. Of the three irradiated fuel pins, two will undergo transient testing, and all three will undergo post-irradiation examination. The methodology development and analysis activities utilized we report enable current experiment design work and provide the pathway through which measured data of this type can be further evaluated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1972

Emergency cooling analysis for the loss of coolant malfunction

This report examines the dynamic response of a conceptual space power fast-spectrum lithium cooled reactor to the loss of coolant malfunction and several emergency cooling concepts. The results show that, following the loss of primary coolant, the peak temperatures of the center most 73 fuel elements can range from 2556 K to the region of the fuel melting point of 3122 K within 3600 seconds after the start of the accident. Two types of emergency aftercooling concepts were examined: (1) full core open loop cooling and (2) partial core closed loop cooling. The full core open loop concept is a one pass method of supplying lithium to the 247 fuel pins. This method can maintain fuel temperature below the 1611 K transient damage limit but requires a sizable 22,680-kilogram auxiliary lithium supply. The second concept utilizes a redundant internal closed loop to supply lithium to only the central area of each hexagonal fuel array. By using this method and supplying lithium to only the triflute region, fuel temperatures can be held well below the transient damage limit.

Peoples, J. A.↗
DOE OSTI2020

Fission Batteries: Definition, Key Attributes and Research and Development Needs

The term battery was first introduced by the American scientist and inventor Benjamin Franklin in 1749, followed by invention of the first true battery in 1800 by Alessandro Volta. Today, batteries are a ubiquitous source of portable electric power across different applications. Batteries are widely used across a range of scales from consumer products to grid-scale energy storage. There are different types of batteries, but they can be broadly classified as chemical or electric batteries [1], atomic batteries, nuclear batteries, tritium batteries or radioisotope generators [2, 3]. Atomic batteries, nuclear batteries, tritium batteries, and radioisotope generators have gained significant attention for applications requi-ing long-term power supply and high-power density, including the space power reactor [4]. While a number of reactor systems, particularly micro-reactors, are referred to as fission batteries, this paper defines key attributes required for a fission reactor to achieve capabilities comparable with the characteristics of batteries that enable their wide-spread use. Achieving this full vision of a fission battery will enable broad deployment of fission reactors that function like batteries. The research and development (R&D) activities needed to achieve the desired fission battery attributes are discussed below.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2022

Post-irradiation Examination Status for the BSU-269 Project

High-density uranium inter-metallic uranium silicide (U 3 Si 2 ) was initially considered as a potential advanced nuclear fuel for light water reactor (LWR) systems due to several advantages it demonstrated in thermophysical properties, chemical, and irradiation stability. In addition to understanding the basic thermophysical and mechanical properties of U 3 Si 2 under LWR irradiation conditions, it is important to assess its performance with advanced claddings such as FeCrAl, SiC, or conventional Zr-based claddings. Several aspects of the fuel cycle and fuel performance are being evaluated for U 3 Si 2 coupled with different types of claddings. To thoroughly characterize the U 3 Si 2 -cladding system, their chemical compatibilities and the potential for fuel-cladding chemical interaction (FCCI) must be addressed. Interdiffusion studies have been performed between U 3 Si 2 /Zry-4 and U 3 Si 2 /FeCrAl using diffusion couples. For the U 3 Si 2 /Zry-4 system, ZrSi 2 was the primary interdiffusion product observed at 800°C in addition to other secondary phases from the Zr alloying elements such as Fe and Cr. Low melting point U 6 Fe was also observed at 1000°C. For the U 3 Si 2 /FeCrAl system, at temperatures above 500°C, chemical diffusion Fe-U and Fe-U-Si was observed, increasing with rising temperatures. Although information from these non-irradiated tests is a fundamental first assessment, follow-up with focused irradiation tests is necessary. Irradiation can significantly alter the structure and evolution of the FCCI layers compared to the non-irradiated conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Evaluation of material accountancy techniques for 233 Pa from thorium nuclear fuels

Thorium is a promising alternative to uranium as nuclear fuel with advantages such as higher abundance, lower production of long-lived transuranic elements, and potentially better proliferation resistance. However, thorium presents a potential pathway for proliferation where produced 233 Pa can be diverted for the clandestine production of safeguarded 233 U. To prevent this, the ability to detect and measure 233 Pa must be assessed. This paper reviews several nuclear material accountancy techniques to determine their suitability for detecting 233 Pa extracted from irradiated thorium fuel. Hybrid K-edge densitometry and passive gamma spectroscopy have been found to be the best options based on technology maturity, cost, accuracy, and acquisition time. Thorium can be used in various reactor designs such as pressurized water reactors (PWRs), Canada deuterium uranium (CANDU) reactors, and molten salt reactors (MSRs). Therefore, thorium-uranium oxide fueling was modeled for three representative reactors (PWR, CANDU, MSR), burning the fuel to 47 GWd/MTHM for PWR, 19 GWd/MTHM for CANDU, and at a steady power of 52.711 MW/MTHM for MSR. Within each model, the protactinium element in the used fuel was extracted and its isotopic content analyzed. Simulated results indicated that 233 Pa can be detected using passive gamma spectroscopy in each fuel type at all decay times (0–300 days) following separation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Progress Toward Molten Salt Reactor Heat Exchanger On-Line Monitoring

Within virtually all reactor systems with heat exchangers, the thinnest barriers between primary and secondary fluids are the heat exchanger tubes. Consistent with light water reactor experience, the advanced reactor heat exchangers are the most susceptible regions for corrosion and leakage (NRC, 2019). Moreover, traditional inspections and repairs using robotics will be expensive or impractical. On-line structural health corrosion monitoring (OLSHM) is therefore desirable to detect tube degradation prior to leaks that may allow mixing of heat exchanger fluids. Rhetorically many molten salt reactor (MSR) designers plan for on-line monitoring of critical reactor components including heat exchangers but there are no proven OLSHM sensors or systems for MSR heat exchangers. Guided wave ultrasound from the tube-end or ID using conventional low-temperature piezoelectric sensors has been shown to be sensitive to pits and cracks less than 50% through-wall in long pipes and tubes (Narayanan M.M., 2019) . Mode and frequency selection are important for practical sensor design decisions and ultimate performance. The L-0 wave-mode is easily excited by L-mode transducers but they have surface normal wave motion that will be sensitive to and more attenuative because of fluid interaction with the tube surface (Rose J.L., 1994). Shear Horizontal (SH) wave modes have material motion parallel to the tube surface therefore are virtually unaffected by fluid interaction. For SH-0 to be nondispersive in steel, the frequency-thickness product (MHz-mm) must be less than approximately 1.5. SH mode transducers must be coupled by a material that can support shear stress; a thin layer of honey works well for temporary sensors and an adhesive or a brazed metallurgical bond for permanent sensors. If sensors are incorporated into the fabrication process, the same kinds of SH-0 waves can be generated from the stagnant flow area of the tube OD without compromising the heat-exchange tube function. Piezoelectric materials are also available that can withstand harsh temperatures of molten salt heat exchangers (Stevenson T., 2015) (Machura et al., 2008). Though they may not have as high-performance characteristics, their performance only needs to be good enough to detect flaws of interest. This project attempts to demonstrate feasibility to develop a sensor that can be sensitive to flaws of interest and perform long-term monitoring of a molten salt reactor heat exchanger. Benefits to the advanced reactor system include: • Minimizing the expense of a reactor shut down for periodic inspection—only shutdown for cause. • Reduce risk of unexpected tube rupture by detecting flaws before they grow to through-wall leaks. • Cost reduction by minimizing need to design for manual/robotic inspectability. Transducer design, characterization of the beam profile, and ultrasonic pulse-echo responses from a representative heat exchange tube with fabricated flaw types are discussed.

On-Line Tube Monitor, Guided Wave Ultrasound, SH-0↗
DOE OSTI2022

Development of a Cloud-based Application to Enable a Scalable Risk-informed Predictive Maintenance Strategy at Nuclear Power Plants

Light-water reactor operations and maintenance (O&M) costs are prohibitively high, thus contributing to the premature decommissioning of nuclear power plants (NPPs). This is partly due to how the equipment is monitored. In recent years, cloud computing has emerged as a dominant technology by virtue of its low costs, computing and storage adaptability, and ability to host applications over numerous types of virtual infrastructures. Cloud computing can be a cost-effective alternative to onsite storage and diagnostics. This paper conducts a techno-economic assessment of a provisional cloud deployment architecture for a NPP predictive monitoring (PdM) system. The cloud-based monitoring system would enable maintenance and diagnostics (M&D) analysts and other authorized plant users to remotely monitor equipment functionality so as to enable PdM practices and early detection of faults. The Microsoft Azure cloud platform is included in the proposed cloud architecture to provide data processing and storage, sensor device networking, and database management; however, this analysis could be extended to other cloud computing service providers as well. For the techno-economic assessment, technical feasibility is measured in terms of network performance metrics such as response time, latency, and throughput, whereas economic feasibility is measured in terms of operational costs and capital expenditures. Finally, this report covers certain regulatory and security aspects that may concern licensees looking to implement cloud computing. The report focuses on the integration of sensor database storage, the application of cloud resources to PdM, and the identification of technological and economic hurdles associated with moving to a cloud-computing-based architecture.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Developing a Facility NMAC Plan

The table presented below suggests the basic information that should be covered in a facility NMAC Plan for an NMAC program that is designed for nuclear security. The topics are appropriate for and should be addressed by all facilities in their NMAC Plans. They are appropriate for NMAC Plans for nuclear power plants, research reactors, fuel manufacturing facilities, facilities that produce medical isotopes, and other facilities. The difference is in the intensity with which the various measures are applied and the thoroughness of the description of the application (i.e., the program requirements). The robustness of a facility NMAC program and the content of its NMAC Plan should be graded in accordance with the type of facility and the category of its nuclear material.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
NASA NTRS2019

Fission Reactor Inadvertent Reentry: A Report to the Nuclear Power & Propulsion Technical Discipline Team

The Nuclear Power and Propulsion Technical Discipline Team has directed an effort to consider possible improvements to the launch approval process as it relates to fission reactors. To that end, Reference 1 described possible general design criteria and risk criteria for fission reactors. At the time that Reference 1 was completed, it was felt that additional examination of reentry issues was warranted. This paper presents the next step in that examination, which is to accurately describe and frame the problem and suggest safety criteria that might apply to inadvertent reentry. The report includes a discussion of the issues associated with different types of inadvertent reentry, the possible consequences of those events, a review of previous work in the area, security and nonproliferation issues, and options for safety requirements that might be considered. Note that safety requirements can have significant mission implications, e.g., no operation below a certain orbit.

Camp, Allen↗
NASA NTRS2024

Rapid Composting of Crop Space Waste

This project processed multiple types of waste simulant feedstocks using commercial composting units and NASA Trash-to-Gas (TtG) technology processing units to see what solids, liquids, and gases could be recovered. The feedstock waste included inedible biomass, mission waste from the Johnson Space Center (JSC) Crew Health and Performance Exploration Analog (CHAPEA), Mars analog, and the long duration Orbital Syngas/Commodity Augmentation Reactor (OSCAR) Waste Simulant (OWS) and OSCAR Full Scale (FS) (also referred to as Mars 850-day mission waste simulant). The performance data was collected, and overall performance of the waste processing systems, as well as elemental analysis of the product yields for enabling Lunar and Martian regolith mixtures in a crop grow-out study, were performed. Germination took place in certain Lunar and Martian regolith studies, with promising preliminary results that TtG solid products can be used as plant nutrients to enable crop growth in off-world regolith simulants.

Anne Meier↗
NASA NTRS2009

Windage Power Loss in Gas Foil Bearings and the Rotor-Stator Clearance of High Speed Generators Operating in High Pressure Environments

Closed Brayton Cycle (CBC) and Closed Supercritical Cycle (CSC) engines are prime candidates to convert heat from a reactor into electric power for robotic space exploration and habitation. These engine concepts incorporate a permanent magnet starter/generator mounted on the engine shaft along with the requisite turbomachinery. Successful completion of the long-duration missions currently anticipated for these engines will require designs that adequately address all losses within the machine. The preliminary thermal management concept for these engine types is to use the cycle working fluid to provide the required cooling. In addition to providing cooling, the working fluid will also serve as the bearing lubricant. Additional requirements, due to the unique application of these microturbines, are zero contamination of the working fluid and entirely maintenance-free operation for many years. Losses in the gas foil bearings and within the rotor-stator gap of the generator become increasingly important as both rotational speed and mean operating pressure are increased. This paper presents the results of an experimental study, which obtained direct torque measurements on gas foil bearings and generator rotor-stator gaps. Test conditions for these measurements included rotational speeds up to 42,000 revolutions per minute, pressures up to 45 atmospheres, and test gases of nitrogen, helium, and carbon dioxide. These conditions provided a maximum test Taylor number of nearly one million. The results show an exponential rise in power loss as mean operating density is increased for both the gas foil bearing and generator windage. These typical "secondary" losses can become larger than the total system output power if conventional design paradigms are followed. A nondimensional analysis is presented to extend the experimental results into the CSC range for the generator windage.

Bruckner, Robert J.↗
DOE OSTI2021

Building Neutron Scattering Infrastructure in Louisiana for Advanced Materials (Final Report)

The main objective of the Louisiana Consortium for Neutron Scattering (LaCNS) is to build a major neutron scattering infrastructure capable of treating both soft and hard materials. The goal is to create a sustainable effort having the quality, breadth, and depth necessary to produce competitive proposals including collaborative and center type proposals. Our scientific aim is to understand the role of coupling in emergent complex materials and its impact on the structure/property relationship and to explore how to tune the key couplings to guide the design of materials with the desired properties. This naturally includes building a base of users of the Spallation Neutron Source (SNS) and the High Flux Isotope Reactor (HFIR) in Louisiana; to train highly talented graduate and post-doctoral students in synthesis, neutron scattering, and simulation and modeling techniques, thereby helping to produce the next generation of scientist who use neutron scattering techniques as a crucial part of their research. The goal of our hard matter program is to understand the interplay between spin, charge, orbital, and lattice degrees of freedom in carefully selected complex materials. We have made considerable progress on number of complex systems including the oxide Sr3(Ru1-xMnx)2O7 where short-range magnetic ordering with anisotropic spin texture is initiated at the metal-insulator transition that clearly indicates a strong spin-charge coupling. Another critical area is in quantum materials. For example, in the topological semimetal BaMnSb2, we found a 3D canted antiferromagnetic Weyl semimetal with a 2D electronic structure and a nontrivial Berry phase. In addition, in the hexagonal chiral Mn1/3NbS2 system, we found soliton/soliton and soliton/antisoliton domain walls where the application of small fields or small currents can be used to control nanoscopic magnetic domains where the control of domain walls is crucially important for information storage. In addition, chemical transformation investigations were performed on the VISION instrument at Spallation Neutron Source (SNS). The soft matter effort was focused on understanding the role of non-covalent interactions on the structure and dynamics of fluid-based soft matter. One key focus was on sequence-defined (SD) amphiphilic peptoid polymers that allow encoding of molecular interactions and thereby systematic investigations of how charge directs the solution self-assembly of amphiphilic polymers in water. Another important area was on the dynamics of lipids self-assembled into membranes for exploring the permeability and mechanical using both neutron spin echo (NSE) spectroscopy and quasielastic neutron scattering (QENS) to distinguished between viscoelasticity and permeability at the molecular scale. Overall, the LaCNS project was quite successful, generating 145 publications and 245 presentations. Our graduate and post-doctoral students were well trained resulting in positions in national laboratories (Oak Ridge National Laboratory (ORNL), Argonne National Laboratory and Los Alamos National Laboratory), major research universities, and industry. We also developed a uniaxial pressure cell along with ORNL for SNS. A critical goal of this project was to establish a foundation for competing nationally in federally funded research programs. To this end, we were quite successful in generating over twenty-two federally and non-federally funded grants including awards from NSF, DOE, and DOD, and two early career awards. Equally important, we were able to secure a key major piece of instrumentation via a large ARO grant for a state-of-the-art electron microscope.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Virtual Resource Management Framework (CRADA Final Report)

There is a need for advanced and widespread business automation within the nuclear industry to drive down operational costs while sustaining or improving safe operations. While there are many business process automation platforms commercially available, the difficulty is that business processes typically rely on a mixture of resource types to accomplish the desired activities and there is no universal software framework virtualizing diverse resource types for the purpose of automation. In this context, we are referring to any capability, physical or intangible, that can be used by an organization to achieve its objectives as a resource. To deploy business automation broadly and enable integrated operations for nuclear (ION), a framework is needed to represent all resource types and their associated disparate data within a plant and to enable seamless flow of resource information to the technologies used for process automation and resource optimization.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1982

Lewis Pressurized, Fluidized-Bed Combustion Program. Data and Calculated Results

A 200 kilowatt (thermal), pressurized, fluidized bed (PFB) reactor and research test facility were designed, constructed, and operated. The facility was established to assess and evaluate the effect of PFB hot gas effluent on aircraft turbine engine materials that may have applications in stationary powerplant turbogenerators. The facility was intended for research and development work and was designed to operate over a wide range of conditions. These conditions included the type and rate of consumption of fuel (e.g., coal) and sulfur reacting sorbent material: the ratio of feed fuel to sorbent material; the ratio of feed fuel to combustion airflow; the depth of the fluidized reaction bed; the temperature and pressure in the reaction bed; and the type of test unit that was exposed to the combustion exhaust gases.

Rollbuhler, R. J.↗
NASA NTRS1993

Preliminary SP-100/Stirling heat exchanger designs

Analytic modeling of several heat exchanger concepts to couple the SP-100 nuclear reactor primary lithium loop and the Space Stirling Power Convertor (SSPC) was performed. Four 25 kWe SSPC's are used to produce the required 100 kW of electrical power. This design work focused on the interface between a single SSPC and the primary lithium loop. Manifolding to separate and collect the four channel flow was not modeled. This work modeled two separate types of heat exchanger interfaces (conductive coupling and radiative coupling) to explore their relative advantages and disadvantages. The minimum mass design of the conductively coupled concepts was 18 kg or 0.73 kg/kWe for a single 25 kWe convertor. The minimum mass radiatively coupled concept was 41 kg or 1.64 kg/kWe. The direct conduction heat exchanger provides a lighter weight system because of its ability to operate the Stirling convertor evaporator at higher heat fluxes than those attainable by the radiatively coupled systems. Additionally the conductively coupled concepts had relatively small volumes and provide potentially simpler assembly. Their disadvantages were the tight tolerances and material joining problems associated with this refractory to superalloy interface. The advantages of the radiatively coupled designs were the minimal material interface problems.

Schmitz, Paul↗