Results for “protective layer” — Page 55

NASA NTRS1975

A method for the dynamic and thermal stress analysis of space shuttle surface insulation

The thermal protection system of the space shuttle consists of thousands of separate insulation tiles bonded to the orbiter's surface through a soft strain-isolation layer. The individual tiles are relatively thick and possess nonuniform properties. Therefore, each is idealized by finite-element assemblages containing up to 2500 degrees of freedom. Since the tiles affixed to a given structural panel will, in general, interact with one another, application of the standard direct-stiffness method would require equation systems involving excessive numbers of unknowns. This paper presents a method which overcomes this problem through an efficient iterative procedure which requires treatment of only a single tile at any given time. Results of associated static, dynamic, and thermal stress analyses and sufficient conditions for convergence of the iterative solution method are given.

Ojalvo, I. U.↗

NASA NTRS1979

The 60-MW Shuttle Interaction Heating Facility

An arc-heated wind-tunnel system described in the present paper will simulate aerodynamic heating in large-scale tests of the thermal protection system of the Shuttle Orbiter Vehicle during entry. The system provides for large-scale subsystem tests in high-enthalpy streams with boundary layer flows at high Reynolds numbers and for large test-body sizes in stagnation flows. The discussion covers the design concept of the arc-jet systems, the extensive hardware developments of the arc heater to provide reliable operation, and verification and performance measurements of the system's operating envelopes.

W Winovich↗

NASA NTRS1999

Numerical Analysis of Convection/Transpiration Cooling

An innovative concept utilizing the natural porosity of refractory-composite materials and hydrogen coolant to provide CONvective and TRANspiration (CONTRAN) cooling and oxidation protection has been numerically studied for surfaces exposed to a high heat flux high temperature environment such as hypersonic vehicle engine combustor walls. A boundary layer code and a porous media finite difference code were utilized to analyze the effect of convection and transpiration cooling on surface heat flux and temperature. The boundary layer code determined that transpiration flow is able to provide blocking of the surface heat flux only if it is above a minimum level due to heat addition from combustion of the hydrogen transpirant. The porous media analysis indicated that cooling of the surface is attained with coolant flow rates that are in the same range as those required for blocking, indicating that a coupled analysis would be beneficial.

Glass, David E.↗

NASA NTRS1999

Numerical Analysis of Convection/Transpiration Cooling

An innovative concept utilizing the natural porosity of refractory-composite materials and hydrogen coolant to provide CONvective and TRANspiration (CONTRAN) cooling and oxidation protection has been numerically studied for surfaces exposed to a high heat flux, high temperature environment such as hypersonic vehicle engine combustor walls. A boundary layer code and a porous media finite difference code were utilized to analyze the effect of convection and transpiration cooling on surface heat flux and temperature. The boundary, layer code determined that transpiration flow is able to provide blocking of the surface heat flux only if it is above a minimum level due to heat addition from combustion of the hydrogen transpirant. The porous media analysis indicated that cooling of the surface is attained with coolant flow rates that are in the same range as those required for blocking, indicating that a coupled analysis would be beneficial.

Glass, David E.↗

NASA NTRS1978

Food Packaging Materials

The photos show a few of the food products packaged in Alure, a metallized plastic material developed and manufactured by St. Regis Paper Company's Flexible Packaging Division, Dallas, Texas. The material incorporates a metallized film originally developed for space applications. Among the suppliers of the film to St. Regis is King-Seeley Thermos Company, Winchester, Ma'ssachusetts. Initially used by NASA as a signal-bouncing reflective coating for the Echo 1 communications satellite, the film was developed by a company later absorbed by King-Seeley. The metallized film was also used as insulating material for components of a number of other spacecraft. St. Regis developed Alure to meet a multiple packaging material need: good eye appeal, product protection for long periods and the ability to be used successfully on a wide variety of food packaging equipment. When the cost of aluminum foil skyrocketed, packagers sought substitute metallized materials but experiments with a number of them uncovered problems; some were too expensive, some did not adequately protect the product, some were difficult for the machinery to handle. Alure offers a solution. St. Regis created Alure by sandwiching the metallized film between layers of plastics. The resulting laminated metallized material has the superior eye appeal of foil but is less expensive and more easily machined. Alure effectively blocks out light, moisture and oxygen and therefore gives the packaged food long shelf life. A major packaging firm conducted its own tests of the material and confirmed the advantages of machinability and shelf life, adding that it runs faster on machines than materials used in the past and it decreases product waste; the net effect is increased productivity.

Source record↗

NASA NTRS2011

CO2 Insulation for Thermal Control of the Mars Science Laboratory

The National Aeronautics and Space Administration (NASA) is sending a large (>850 kg) rover as part of the Mars Science Laboratory (MSL) mission to Mars in 2011. The rover's primary power source is a Multi-Mission Radioisotope Thermoelectric Generator (MMRTG) that generates roughly 2000 W of heat, which is converted to approximately 110 W of electrical power for use by the rover electronics, science instruments, and mechanism-actuators. The large rover size and extreme thermal environments (cold and hot) for which the rover is designed for led to a sophisticated thermal control system to keep it within allowable temperature limits. The pre-existing Martian atmosphere of low thermal conductivity CO2 gas (8 Torr) is used to thermally protect the rover and its components from the extremely cold Martian environment (temperatures as low as -130 deg C). Conventional vacuum based insulation like Multi Layer Insulation (MLI) is not effective in a gaseous atmosphere, so engineered gaps between the warm rover internal components and the cold rover external structure were employed to implement this thermal isolation. Large gaps would lead to more thermal isolation, but would also require more of the precious volume available within the rover. Therefore, a balance of the degree of thermal isolation achieved vs. the volume of rover utilized is required to reach an acceptable design. The temperature differences between the controlled components and the rover structure vary from location to location so each gap has to be evaluated on a case-by-case basis to arrive at an optimal thickness. For every configuration and temperature difference, there is a critical thickness below which the heat transfer mechanism is dominated by simple gaseous thermal conduction. For larger gaps, the mechanism is dominated by natural convection. In general, convection leads to a poorer level of thermal isolation as compared to conduction. All these considerations play important roles in the optimization process. A three-step process was utilized to design this insulation. The first step is to come up with a simple, textbook based, closed-form equation assessment of gap thickness vs. resultant thermal isolation achieved. The second step is a more sophisticated numerical assessment using Computational Fluid Dynamics (CFD) software to investigate the effect of complicated geometries and temperature contours along them to arrive at the effective thermal isolation in a CO2 atmosphere. The third step is to test samples of representative geometries in a CO2 filled chamber to measure the thermal isolation achieved. The results of these assessments along with the consistency checks across these methods leads to the formulation of design-guidelines for gap implementation within the rover geometry. Finally, based on the geometric and functional constraints within the real rover system, a detailed design that accommodates all these factors is arrived at. This paper will describe in detail this entire process, the results of these assessments and the final design that was implemented.

CO2↗

DOE OSTI2021

Solar mirrors and methods of making solar mirrors having improved properties

A solar reflective mirror includes a parting film between solar reflecting sublayers to improve optics and stability of the solar mirror. The coating stack of the solar reflector mirror is encapsulated to increase the useable life of the solar mirror, and to eliminate the need for a permanent protection overcoat. Omission of the PPO film which is electrically non-conductive makes the coating stack electrically conductive eliminating the need for a two layer encapsulant when the encapsulant is e-coated.Another feature of the invention is applying the base coat of the encapsulant over the marginal edges of the PPO film leaving a center section without coverage and adding the top coating of the encapsulant over the base coat and the uncoated area.

Medwick, Paul A.↗

NASA NTRS1991

Protective Al2O3 scale formation on NbAl3-base alloys

The oxidation of NbAl3 with additions of Cr and Y was studied to determine the mechanisms of the beneficial effects of these elements upon oxidation. Cr additions to the binary NbAl3 alloy of up to 6.8 at. percent reduced the scale growth rates and promoted alpha-Al2O3 formation over much longer times relative to binary NbAl3. A major effect of Cr is to form a layer of AlNbCr at the metal/scale interface, which is inherently more oxidation-resistant than the matrix alloy in the long term. Yttrium additions to a Cr-containing alloy improved the scale growth rate and adherence and changed the scale microstructure to mimic that of a typical protective Al2O3 scale.

Doychak, J.↗

NASA NTRSDate not supplied

Validation and Sensitivity Analyses of Arc-Jet Performance of Woven Thermal Protection Entry Systems

A material response model is developed for the determination of erosion rates and thermal response of woven materials to enable accurate thermal protection material sizing and future missions to Venus and giant planets. The stagnation-point thermal response is further evaluated using a Monte Carlo global sensitivity analysis to determine the interactions between key parameters in the material surface energy balance, such as, convective blowing correction parameter and weave material properties including isotropic and orthotropic thermal conductivites. The time-accurate material response for the dual layer weave erosion and surface temperatures show excellent agreement with stagnation flat face arc-jet tests involving time-varying aeroheating-cooling cycles. The high-fidelity Monte Carlo sensitivity analysis technique was used to address challenges in thermal protection sizing for the Adaptive Deployable Entry and Placement Technology (ADEPT) system, a low ballistic coefficient hypersonic decelerator. The results represent new correlations for such weaves involving Carbon-air oxidation equilibrium chemistry. Through the multi-variate regression analyses and uncertainty rankings performed, only three properties were found to contribute to the transient thermal response of the gore, with emissivity contributing to nearly 95% of the total output uncertainty.

Pratibha Raghunandan↗

NASA NTRS2021

Validation and Sensitivity Analyses of Arc-Jet Performance of Woven Thermal Protection Entry Systems

A material response model is developed for the determination of erosion rates and thermal response of woven materials to enable accurate thermal protection material sizing and future missions to Venus and giant planets. The stagnation-point thermal response is further evaluated using a Monte Carlo global sensitivity analysis to determine the interactions between key parameters in the material surface energy balance, such as, convective blowing correction parameter and weave material properties including isotropic and orthotropic thermal conductivites. The time-accurate material response for the dual layer weave erosion and surface temperatures show excellent agreement with stagnation flat face arc-jet tests involving time-varying aeroheating-cooling cycles. The high-fidelity Monte Carlo sensitivity analysis technique was used to address challenges in thermal protection sizing for the Adaptive Deployable Entry and Placement Technology (ADEPT) system, a low ballistic coefficient hypersonic decelerator. The results represent new correlations for such weaves involving Carbon-air oxidation equilibrium chemistry. Through the multi-variate regression analyses and uncertainty rankings performed, only three properties were found to contribute to the transient thermal response of the gore, with emissivity contributing to nearly 95% of the total output uncertainty.

Pratibha Raghunandan↗

NASA NTRS1987

Aircraft Seat Cushion Fire-Blocking Layers

229-page report describes work done to determine burning characteristics of present and proposed seat-cushion materials and types of construction. Tested cushions classified in four groups: standard cushion construction, standard cushion construction with protective covering enveloping urethane-foam core, standard cushion construction with protective covering enveloping non-fire-retarded urethane-foam core, and standard cushion construction with urethane-foam core replaced by advanced fire-resistant foam. Report includes still photographs and presents quantitative data from each test in graphs and tables.

Schutter, Kenneth J.↗

NASA NTRS1982

Transient thermal analysis of a titanium multiwall thermal protection system

The application of the SPAR thermal analyzer to the thermal analysis of a thermal protection system concept is discussed. The titanium multiwall thermal protection system concept consists of alternate flat and dimpled sheets which are joined together at the crests of the dimples and formed into 30 cm by 30 cm (12 in. by 12 in.) tiles. The tiles are mechanically attached to the structure. The complex tile geometry complicates thermal analysis. Three modes of heat transfer were considered: conduction through the gas inside the tile, conduction through the metal, and radiation between the various layers. The voids between the dimpled and flat sheets were designed to be small enough so that natural convection is insignificant (e.g., Grashof number 1000). A two step approach was used in the thermal analysis of the multiwall thermal protection system. First, an effective normal (through-the-thickness) thermal conductivity was obtained from a steady state analysis using a detailed SPAR finite element model of a small symmetric section of the multiwall tile. This effective conductivity was then used in simple one dimensional finite element models for preliminary analysis of several transient heat transfer problems.

Blosser, M. L.↗

DOE OSTI2022

Self-Protective Inverters Against Malicious Setpoints Using Analytical Reference Models

This paper presents the concept of self-protective inverters using reference models. In the proposed method, incoming setpoints from the utility operator or third-party aggregators are inspected using analytical reference models before engaging the setpoints to the inverter’s local controller. When a malicious setpoint passes the existing security layers, a smart inverter can examine the integrity of an incoming setpoint in real-time. The efficacy of the developed method has been tested using a laboratory setup, including a three-phase 3kVA SiC-MOSFET inverter and a 12kW NHR 9410 regenerative grid emulator. Furthermore, the results verify that the developed analytical models can provide device-level protection for grid-interactive inverters by inspecting and preventing harmful setpoints from getting engaged to the local controller.

42 ENGINEERING↗

NASA NTRS1981

Galileo Probe forebody thermal protection

Material response solutions for the forebody heat shield on the candidate 310-kg Galileo Probe are presented. A charring material ablation analysis predicts thermochemical surface recession, insulation thickness, and total required heat shield mass. Benchmark shock layer solutions provide the imposed entry heating environments on the ablating surface. Heat shield sizing results are given for a nominal entry into modeled nominal and cool-heavy Jovian atmospheres, and for two heat-shield property models. The nominally designed heat shield requires a mass of at least 126 kg and would require an additional 13 kg to survive entry into the less probable cool-heavy atmosphere. The material-property model with a 30% surface reflectance reduces these mass requirements by as much as 16%.

Green, M. J.↗

NASA NTRSDate not supplied

Case Study of Meteoroid Fluence on a Mars Sample Return Mission

The Mars Sample Return Campaign must satisfy a Back Planetary Protection requirement that limits the risk of biological contamination of the Earth by Martian microbes. The Earth Re-turn Orbiter (ERO), being developed by the European Space Agency (ESA), will carry a Capture, Containment and Return System (CCRS), which is being developed by NASA to retrieve orbiting samples (OS) from Mars orbit, surround them with two containment layers to create a Contained OS (COS), and transfer the COS to the Earth Entry System (EES), which will be re-leased by ERO to carry the samples through entry, descent and landing at the Utah Test and Training Range. Micrometeoroid impact damage to the Thermal Protection System (TPS) of the EES, which may occur at any time in the ERO mission, is recognized as a potential risk driver for loss of sample containment that needs to be rigorously assessed. A Micrometeoroid Protection System (MMPS) will be implemented to limit that risk. The MMPS consists of a shield covering the TPS called the Micrometeoroid Garage (MMG) and a system of cameras to inspect the TPS. An extensive study was performed by the CCRS Project in collaboration with the NASA Engineering and Safety Center (NESC)to assess the probability of damage to the MMG and TPS by meteoroids over the entire ERO mission. This included the computation of the meteoroid fluence on the MMG and directly on the TPS after EES separation, and assessment of damage to the MMG and TPS via hypervelocity impact tests, hydrocode simulations, and empirical damage prediction and ballistic limit equations (BLEs). The focus of this paper is the meteoroid fluence on the MMG.

Micrometeoroid↗

NASA NTRSDate not supplied

Case Study of Meteoroid Fluence on a Mars Sample Return Mission

The Mars Sample Return Campaign must satisfy a Back Planetary Protection requirement that limits the risk of biological contamination of the Earth by Martian microbes. The Earth Re-turn Orbiter (ERO), being developed by the European Space Agency (ESA), will carry a Capture, Containment and Return System (CCRS), which is being developed by NASA to retrieve orbiting samples (OS) from Mars orbit, surround them with two containment layers to create a Contained OS (COS), and transfer the COS to the Earth Entry System (EES), which will be re-leased by ERO to carry the samples through entry, descent and landing at the Utah Test and Training Range. Micrometeoroid impact damage to the Thermal Protection System (TPS) of the EES, which may occur at any time in the ERO mission, is recognized as a potential risk driver for loss of sample containment that needs to be rigorously assessed. A Micrometeoroid Protection System (MMPS) will be implemented to limit that risk. The MMPS consists of a shield covering the TPS called the Micrometeoroid Garage (MMG) and a system of cameras to inspect the TPS. An extensive study was performed by the CCRS Project in collaboration with the NASA Engineering and Safety Center (NESC)to assess the probability of damage to the MMG and TPS by meteoroids over the entire ERO mission. This included the computation of the meteoroid fluence on the MMG and directly on the TPS after EES separation, and assessment of damage to the MMG and TPS via hypervelocity impact tests, hydrocode simulations, and empirical damage prediction and ballistic limit equations (BLEs). The focus of this paper is the meteoroid fluence on the MMG.

micrometeoroid↗

DOE OSTI2021

Thermomechanical and sequential stress performance of photovoltaic backsheets

Photovoltaic backsheet technology is utilized to protect the interior components of solar modules from environmental stress as well as provide electrical insulation to the module. The growing demand for solar energy and longer module service life requirements have brought backsheet performance into focus. Despite being a protective packaging material, many backsheets have exhibited failure in the field, limiting the performance and service life of entire modules. Most backsheets consist of multiple polymeric layers laminated together using adhesives. A new backsheet, with a high performance polyamide structure, has been developed as the solution to module failure. Primarily, it contains a unique polyamide-ionomer alloy targeted at improved weather resistance. In this study, several photovoltaic industry standard backsheets, and the novel polyamide compositions of multilayered backsheets fabricated from the coextrusion process, were examined using thermomechanical analysis (TMA). The coefficient of thermal expansion (CTE) for entire backsheets and their constituent layers was used to model the thermomechanical behavior of various backsheet constructions. Subsequently, thermal cycling was performed in the TMA to examine the intrinsic thermal behavior of the backsheets. Thermal cycling in the TMA indicates the resilience and dimensional stability in the coextruded structures as opposed to the laminated structures. Lastly, results from a Module Accelerated Sequential Testing (MAST), are included to show the mechanical integrity of these backsheets after sequential exposure to stressors including damp heat, ultra-violet (UV) light radiation, and thermal cycling. The laminate backsheets deteriorated extensively after sequential exposure to these stressors, while the novel coextruded structures retained their physical properties.

14 SOLAR ENERGY↗

DOE OSTI2026

Multiscale Cryo Electron Microscopy Reveals Interfacial Degradation and Stabilization in Battery Electrodes

Electrochemical interfaces are dynamic systems, evolving based on their local environment and reactant surface structures. The electrode-electrolyte interface in Li-ion batteries can be protective, limiting parasitic reactions with the electrolyte to passivate the surface [1]. Additionally, this interphase has an impact on the Li-ion transport through that layer based on its composition, bonding environment, and thickness. These parameters are challenging to collect and may vary depending on the electrode surface site investigated relative to its spatial position in a coin cell. This study will detail a multiscale cryogenic electron microscopy approach where millimeter-scale cross-sections through the coin cell batteries were made using a cryogenic stage within a fs-laser plasma focused ion beam (laser PFIB) with complementary energy dispersive X-ray spectroscopy able to detect variations in the composition at electrode interfaces [2]. Microscale cross-sectioning and lamella sample preparation of battery electrodes was conducted at the Center for Integrated Nanotechnologies using a Ga-ion focused ion beam (FIB) with air-free and cryo-transfer [3], followed by nanoscale mapping of composition and bonding within the CEI through cryo-scanning transmission electron microscopy (cryo-STEM) electron energy loss spectroscopy [4]. This multiscale approach enabled identification of millimeter-scale features of a battery stack with visualization of degradation in electrodes such as cracks in cathode particles, gas evolution, and SEI evolution; microscale interfacial characteristics, such as heterogeneity in the SEI or barrier layer and identification of electrolyte networks to the electrode surfaces; and nanoscale measurement of the CEI thickness, mapping of transition metal bonding within the cathode particles to identify loss of active materials, and identification of beneficial electrolyte additives incorporated into the CEI structure. This multiscale approach allows for a statistical understanding of the primary mechanisms and parasitic degradation pathways that impact performance by limiting the ion transport pathways within Li+ batteries.

36 MATERIALS SCIENCE↗