Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power engineering computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS1934

A method of calculating the performance of controllable propellers with sample computations

This paper contains a series of calculations showing how the performance of controllable propellers may be derived from data on fixed-pitch propellers given in N.A.C.A. Technical Report No. 350, or from similar data. Sample calculations are given which compare the performance of airplanes with fixed-pitch and with controllable propellers. The gain in performance with controllable propellers is shown to be largely due to the increased power available, rather than to an increase in efficiency. Controllable propellers are of particular advantage when used with geared and with supercharged engines. A controllable propeller reduces the take-off run, increases the rate of climb and the ceiling, but does not increase the high speed, except when operating above the design altitude of the previously used fixed-pitch propeller or when that propeller was designed for other than high speed.

Hartman, Edwin P↗
DOE OSTI2025

Single-shot electrical detection of short-wavelength magnon pulse transmission in a magnonic thin-film waveguide

Abstract The advance of magnon spintronics requires understanding of time-domain magnon pulse transmission in order to develop high-speed information processing protocols. In this work, we demonstrate single-shot electrical detection of narrow-band magnon pulse transmission in a yttrium iron garnet thin-film delay line. The high signal-to-background ratio of magnon transmission band allows us to directly probe the magnon transmission electrically using a fast oscilloscope and to study its spectral evolution using Fast Fourier Transform (FFT) of the time-domain transmitted signal. At elevated input power, we show a magnon transmission reduction and a spectral distortion, which can be understood by the nonlinear magnon excitation in the transmission band defined by the antenna geometry. In addition, we also find that the higher- (lower-) frequency magnon spectral component exhibits a lower (higher) magnon group velocity, showing a dispersion agreeing with the Damon-Eshbach dependence. Our results provide important guidance of magnon pulse engineering for their applications in spin wave computing and coherent magnon information processing.

Song, Moojune↗
NASA NTRS2001

Physical Processes Governing Atmospheric Trace Constituents Measured from an Aircraft on PEM-Tropics

Before the mission, the PI (principal investigator) was instrumental in securing real-time use of the new 51-level ECMWF (European Centre for Medium Range Weather Forecasts) meteorological data. During the mission, he provided flight planning and execution guidance as meteorologist for the P-3B. Mr. Yong Zhu computed and plotted meteorological forecast maps using the ECMWF data and transmitted them to the field from MIT (Massachusetts Institute of Technology). Dr. John Cho was in the field for the Christmas Island portion to extract data from the on-site NOAA (National Oceanic and Atmospheric Administration) radars for local wind profiles that were used at the flight planning meetings. When the power supply for the VHF radar failed, he assisted the NOAA engineer in its repair. After the mission, Mr. Zhu produced meteorological data memos, which were made available to the PEM (Pacific Exploratory Mission)-Tropics B science team on request. An undergraduate student, Ms. Danielle Morse, wrote memos annotating the cloud conditions seen on the aircraft external monitor video tapes. Dr. Cho and the PI circulated a memo regarding the status (and associated problems) of the meteorological measurement systems on the DC-8 and P-3B to the relevant people on the science team. Several papers by members of our project were completed and accepted by JGR (Journal of Geophysical Research) for the first special section on PEM-Tropics B. These papers included coverage of the following topics: 1) examination of boundary layer data; 2) water vapor transport; 3) tropospheric trace constituent layers; 4) summarizations of the meteorological background and events during PEM-Tropics B; 5) concomitant lidar measurements of ozone, water vapor, and aerosol.

Newell, Reginald E.↗
NASA NTRS2011

Development of an Open Rotor Cycle Model in NPSS Using a Multi-Design Point Approach

NASA's Environmentally Responsible Aviation Project and Subsonic Fixed Wing Project are focused on developing concepts and technologies which may enable dramatic reductions to the environmental impact of future generation subsonic aircraft (Refs. 1 and 2). The open rotor concept (also referred to as the Unducted Fan or advanced turboprop) may allow the achievement of this objective by reducing engine emissions and fuel consumption. To evaluate its potential impact, an open rotor cycle modeling capability is needed. This paper presents the initial development of an open rotor cycle model in the Numerical Propulsion System Simulation (NPSS) computer program which can then be used to evaluate the potential benefit of this engine. The development of this open rotor model necessitated addressing two modeling needs within NPSS. First, a method for evaluating the performance of counter-rotating propellers was needed. Therefore, a new counter-rotating propeller NPSS component was created. This component uses propeller performance maps developed from historic counter-rotating propeller experiments to determine the thrust delivered and power required. Second, several methods for modeling a counter-rotating power turbine within NPSS were explored. These techniques used several combinations of turbine components within NPSS to provide the necessary power to the propellers. Ultimately, a single turbine component with a conventional turbine map was selected. Using these modeling enhancements, an open rotor cycle model was developed in NPSS using a multi-design point approach. The multi-design point (MDP) approach improves the engine cycle analysis process by making it easier to properly size the engine to meet a variety of thrust targets throughout the flight envelope. A number of design points are considered including an aerodynamic design point, sea-level static, takeoff and top of climb. The development of this MDP model was also enabled by the selection of a simple power management scheme which schedules propeller blade angles with the freestream Mach number. Finally, sample open rotor performance results and areas for further model improvements are presented.

Hendricks, Eric S.↗
NASA NTRS2016

Overview of ERA Integrated Technology Demonstration (ITD) 51A Ultra-High Bypass (UHB) Integration for Hybrid Wing Body (HWB)

The NASA Environmentally Responsible Aircraft Project (ERA) was a ve year project broken into two phases. In phase II, high N+2 Technical Readiness Level demonstrations were grouped into Integrated Technology Demonstrations (ITD). This paper describes the work done on ITD-51A: the Vehicle Systems Integration, Engine Airframe Integration Demonstration. Refinement of a Hybrid Wing Body (HWB) aircraft from the possible candidates developed in ERA Phase I was continued. Scaled powered, and unpowered wind- tunnel testing, with and without acoustics, in the NASA LARC 14- by 22-foot Subsonic Tunnel, the NASA ARC Unitary Plan Wind Tunnel, and the 40- by 80-foot test section of the National Full-Scale Aerodynamics Complex (NFAC) in conjunction with very closely coupled Computational Fluid Dynamics was used to demonstrate the fuel burn and acoustic milestone targets of the ERA Project.

Flamm, Jeffrey D.↗
NASA NTRSDate not supplied

Multiphase Simulations of the SLS Launch Environment

NASA’s Space Launch System (SLS), which will send astronauts back to the Moon in the next few years, is powered by four RS-25 engines and two RSRMV solid rocket boosters (SRBs). During launch the SLS propulsion system generates intense acoustics and other powerful waves, such as ignition overpressure (IOP) which, if unmitigated, have the potential to damage the vehicle and possibly cause loss of mission or crew. To protect the vehicle from these powerful waves, the SLS launch pad design includes an ignition overpressure/sound suppression (IOP/SS) system which sprays 270,000 gallons per minute of water very close to the SRB and RS-25 nozzles. The SRB and RS-25 engine plumes, and the proximity of the IOP/SS water, create a complex multiphase (gas and liquid) environment during the SLS ignition sequence. The interplay among these systems creates challenges related to water spray into/onto engine nozzles, potential debris transport, and additional transient loads due to strong plume-water interactions - all of which the SLS vehicle must be able to withstand. Prior to the Artemis I launch, the SLS multiphase liftoff environment was largely unknown due to differences from the Space Shuttle and other programs. Some data was available from tests of individual systems, but no integrated testing or analysis was available. Even post-launch analysis of Artemis I cannot provide a full understanding of the complex physics involved due to limited (or obstructed) camera views and instrumentation. Computational fluid dynamics (CFD) is being used to investigate the details of the multiphase environment which could not be measured, help comprehend the data gathered from the launch, and ultimately identify phenomena that are a concern for future flights. Project Details Engineers at NASA’s Marshall Space Flight Center (MSFC) have executed simulations using the Loci/STREAM-Volume of Fluid (VoF) multiphase CFD solver to understand this environment. Initial efforts successfully validated the CFD solver on various tests, giving confidence to simulate the SLS multiphase liftoff environment prior to the Artemis I launch. The CFD simulation of the SLS ignition sequence was conducted in three phases. First the IOP/SS water system was simulated for approximately 6 seconds to reach a quasi-steady state. Next, the RS-25 engine plumes were activated and held at full power for 1 second. Lastly, the SRB booster was activated and the simulation was carried out until just prior to vehicle motion. This simulation process mimics the conditions that exist at launch. Results and Impact The SLS ignition sequence simulation results provide deep understanding of the underlying physics occuring during launch. Observations from the simulation include reduction of water splashing into/onto the engine nozzles, change in angling of the dense water sheets, and the origin of the powerful ignition overpressure (IOP) wave. These observations directly inform the SLS program on subjects including plume-water induced side loads, debris transport, and the acoustic launch environment. Additionally, with post launch comparison of CFD observations to flight data, these tools can be applied to launch vehicles and environments other than SLS with confidence. Why HPC Matters The SLS ignition sequence CFD simulations are conducted on meshes up to hundreds of millions of cells on thousands of processors for weeks at a time. These simulations generate terabytes of data that must also be stored and archived for future use on HPC systems. Simply put, the CFD simulations would not be possible without NASA HPC resources. What’s Next Comparisons between the Artemis I flight data and the CFD simulations will be continued to both improve confidence in the CFD results and provide deeper understanding into the SLS multiphase launch environment. This will be used to provide insight for decision making for the first manned SLS flight, Artemis II. Future simulations will target new configurations of the SLS IOP/SS water required to support the more powerful variants of the SLS vehicle, such as Block 1B. Additionally, this capability provides NASA the ability to investigate launch environments for vehicles other than SLS to support other missions.

Travis Rivord↗
DOE OSTI2020

Additive Manufacturing Technologies Survey

A literature search of the most prominent and widely available additive manufacturing technologies was done to understand the current developments in this area. The first section provides the introduction and scope for this report, followed by a very detailed second section on the different types of additive manufacturing technologies, how they work, the materials used, advantages and disadvantages of each technology, and manufacturer information. For comparative purposes, a third section on the most widely used subtractive technology, Computer Numerical Control (CNC) machining, is presented with information about the parameters used and the benefits and limitations of this technology. A final section with a summary and conclusions is presented with information comparing the power and utility of the different additive manufacturing technologies compared to traditional manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupled TD Simulation project (Final Report)

This project implements coupled simulation of electric power grid transmission and distribution (T&D) by instantiating the co-simulation platform HELICS using a commercial distribution planning software CYMDIST1 by Eaton Inc., a power management company, and by leveraging the open-source transmission grid simulator GridDyn and LLNL’s High Performance Computing (HPC). The project is funded by DOE’s Technology Commercialization Funding (TCF) and supported by DOE Office of Technology Transitions (OTT).

14 SOLAR ENERGY↗
NASA NTRS1991

Numerical simulation of shock-induced combustion/detonation in a premixed H2-air mixture using Navier-Stokes equations

A numerical study was conducted to address the structural stability of the oblique detonation wave. An attempt was made to isolate the structural instability predicted by Buckmaster's (1990) linear stability analysis. For this study a detailed viscous flowfield with finite-rate chemistry was computed past a 20-deg wedge. The finite-rate chemistry was modeled by using a seven-species and seven-reaction model. Instability modes were isolated by analyzing the Fourier power spectrum of the H2O mass fraction at selected sample stations. No unstable temporal modes with dominant frequency were isolated. It was concluded that the instability which is predicted by the Buckmaster work was a high-frequency low-amplitude phenomenon. For engineering purposes, the oblique detonation wave is a stable phenomenon as long as sufficient levels of overdrive are present.

Singh, D. J.↗
NASA NTRS1992

Control-structure-thermal interactions in analysis of lunar telescopes

The lunar telescope project was an excellent model for the CSTI study because a telescope is a very sensitive instrument, and thermal expansion or mechanical vibration of the mirror assemblies will rapidly degrade the resolution of the device. Consequently, the interactions are strongly coupled. The lunar surface experiences very large temperature variations that range from approximately -180 C to over 100 C. Although the optical assemblies of the telescopes will be well insulated, the temperature of the mirrors will inevitably fluctuate in a similar cycle, but of much smaller magnitude. In order to obtain images of high quality and clarity, allowable thermal deformations of any point on a mirror must be less than 1 micron. Initial estimates indicate that this corresponds to a temperature variation of much less than 1 deg through the thickness of the mirror. Therefore, a lunar telescope design will most probably include active thermal control, a means of controlling the shape of the mirrors, or a combination of both systems. Historically, the design of a complex vehicle was primarily a sequential process in which the basic structure was defined without concurrent detailed analyses or other subsystems. The basic configuration was then passed to the different teams responsible for each subsystem, and their task was to produce a workable solution without requiring major alterations to any principal components or subsystems. Consequently, the final design of the vehicle was not always the most efficient, owing to the fact that each subsystem design was partially constrained by the previous work. This procedure was necessary at the time because the analysis process was extremely time-consuming and had to be started over with each significant alteration of the vehicle. With recent advances in the power and capacity of small computers, and the parallel development of powerful software in structural, thermal, and control system analysis, it is now possible to produce very detailed analyses of intermediate designs in a much shorter period of time. The subsystems can thus be designed concurrently, and alterations in the overall design can be quickly adopted into each analysis; the design becomes an iterative process in which it is much easier to experiment with new ideas, configurations, and components. Concurrent engineering has the potential to produce efficient, highly capable designs because the effect of one subystem on another can be assessed in much more detail at a very early point in the program. The research program consisted of several tasks: scale a prototype telescope assembly to a 1 m aperture, develop a model of the telescope assembly by using finite element (FEM) codes that are available on site, determine structural deflections of the mirror surfaces due to the temperature variations, develop a prototype control system to maintain the proper shape of the optical elements, and most important of all, demonstrate the concurrent engineering approach with this example. In addition, the software used for the finite element models and thermal analysis was relatively new within the Program Development Office and had yet to be applied to systems this large or complex; understanding the software and modifying it for use with this project was also required. The I-DEAS software by Structural Dynamics Research Corporation (SDRC) was used to build the finite element models, and TMG developed by Maya Heat Transfer Technologies, Ltd. (which runs as an I-DEAS module) was used for the thermal model calculations. All control system development was accomplished with MATRIX(sub X) by Integrated Systems, Inc.

Thompson, Roger C.↗
NASA NTRS1997

The Effect of Pulse Shaping QPSK on Bandwidth Efficiency

This research investigates the effect of pulse shaping QPSK on bandwidth efficiency over a non-linear channel. This investigation will include software simulations and the hardware implementation. Three kinds of filters: the 5th order Butterworth filter, the 3rd order Bessel filter and the Square Root Raised Cosine filter with a roll off factor (alpha) of 0.25,0.5 and 1, have been investigated as pulse shaping filters. Two different high power amplifiers, one a Traveling Wave Tube Amplifier (TWTA) and the other a Solid State Power Amplifier (SSPA) have been investigated in the hardware implementation. A significant improvement in the bandwidth utilization (rho) for the filtered data compared to unfiltered data through the non-linear channel is shown in the results. This method promises strong performance gains in a bandlimited channel when compared to unfiltered systems. This work was conducted at NMSU in the Center for Space Telemetering, and Telecommunications Systems in the Klipsch School of Electrical and Computer Engineering Department and is supported by a grant from the National Aeronautics and Space Administration (NASA) NAG5-1491.

Purba, Josua Bisuk Mubyarto↗
NASA NTRS2017

Integrated Display and Environmental Awareness System - System Architecture Definition

The Integrated Display and Environmental Awareness System (IDEAS) is an interdisciplinary team project focusing on the development of a wearable computer and Head Mounted Display (HMD) based on Commercial-Off-The-Shelf (COTS) components for the specific application and needs of NASA technicians, engineers and astronauts. Wearable computers are on the verge of utilization trials in daily life as well as industrial environments. The first civil and COTS wearable head mounted display systems were introduced just a few years ago and they probed not only technology readiness in terms of performance, endurance, miniaturization, operability and usefulness but also maturity of practice in perspective of a socio-technical context. Although the main technical hurdles such as mass and power were addressed as improvements on the technical side, the usefulness, practicality and social acceptance were often noted on the side of a broad variety of humans' operations. In other words, although the technology made a giant leap, its use and efficiency still looks for the sweet spot. The first IDEAS project started in January 2015 and was concluded in January 2017. The project identified current COTS systems' capability at minimum cost and maximum applicability and brought about important strategic concepts that will serve further IDEAS-like system development.

Wearables↗
DOE OSTI2020

JMOCUP Physics Depletion Calculations for the As-Run AGR-5/6/7 TRISO Particle Experiment in ATR Northeast Flux Trap

This ECAR documents the as-run Jim Sterbentz’s MCNP ORIGEN Coupled Utility Program (JMOCUP) physics depletion calculation and the calculated results for the AGR-5/6/7 irradiation experiment in the Advanced Test Reactor (ATR). AGR 5/6/7 was irradiated for nine power cycles in the northeast flux trap. The depletion calculations were performed to provide input data for a variety of other engineering analyses supporting the AGR-5/6/7 experiment along with post-irradiation characterization of the tri-structural isotropic (TRISO) particle fuel compacts. Detailed full-core MCNP models and Oak Ridge Isotope Generation (ORIGEN2) radionuclide generation models were specifically developed as part of the JMOCUP Monte Carlo depletion calculations. The MCNP ORIGEN2 computer codes were coupled using the well-established JMOCUP utility modules to couple the two codes and run the depletion calculations. The physics calculations were performed in support of the Advanced Gas Reactor (AGR) program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Demonstrating solarpilot ’s Python Application Programmable Interface Through Heliostat Optimal Aimpoint Strategy Use Case

solarpilot is a software package that generates solar field layouts and characterizes the optical performance of concentrating solar power (CSP) tower systems. solarpilot was developed by the National Renewable Energy Laboratory (NREL) as a stand-alone desktop application but has also been incorporated into NREL’s System Advisor Model (SAM) in a simplified format. Prior means for user interaction with solarpilot have included the application’s graphical interface, the SAM routines with limited configurability, and through a built-in scripting language called “LK.” This article presents a new, full-featured, python-based application programmable interface (API) for solarpilot, which we hereafter refer to as CoPylot. CoPylot enables python users to perform detailed CSP tower analysis utilizing either the Hermite expansion technique (analytical) or the SolTrace ray-tracing engine. CoPylot’s enables CSP researchers to perform analysis that was previously not possible through solarpilot’s existing interfaces. This article discusses the capabilities of CoPylot and presents a use case wherein we populate a model that obtains optimal solar field aiming strategies.

14 SOLAR ENERGY↗
NASA NTRS1986

Engineering Voyager 2's encounter with Uranus

Changes made by radio control from the ground in the Voyager 2 spacecraft as it approached Uranus are described. Reduced power required that subsystems and heaters had to be switched on and off in carefully synchronized fashion. Low light levels required increased exposure times, so the jiggling of the spacecraft had to be minimized. Coding changes were made and image data were compressed to cope with the reduced bit rate at larger distances. Successful efforts to cope with failures in the primary radio receiver and in the computer instructions for image compression are described, as are changes made on the ground in the spacecraft navigation.

Laeser, Richard P.↗
DOE OSTI2021

Distributed and communication-efficient solutions to linear equations with special sparse structure

In this paper we report two distributed and communication-efficient algorithms based on the multi-agent system are proposed to solve a system of linear equations with the Laplacian sparse system matrix. One algorithm is based on the gradient descent method in optimization. In this algorithm, the agents only share partial information instead of all of their collective state vectors to save significant communication. The other algorithm is obtained by approximating Newton’s method for a faster convergence rate. Although it requires twice as much communication as the first one, it is still communication-efficient given the low dimension of the information shared among agents. The convergence at a linear rate is proved for both algorithms, and a comprehensive comparison of their convergence rate, communication burden, and computation costs is also performed. The proposed algorithms can be applied to various systems to solve those problems that can be modeled as a system of linear equations with a Laplacian sparse system matrix. Simulation results with the electric power system illustrate their effectiveness.

42 ENGINEERING↗
DOE OSTI2025

Improving photovoltaic hosting capacity of distribution networks with coordinated inverter control: A case study of the EPRI J1 feeder

Abstract Adding photovoltaic (PV) systems in distribution networks, while desirable for reducing the carbon footprint, can lead to voltage violations under high solar‐low load conditions. The inability of traditional volt‐VAr control in eliminating all the violations is also well‐known. This article presents a novel coordinated inverter control methodology that leverages system‐wide situational awareness to significantly improve hosting capacity (HC). The methodology employs a real‐time voltage‐reactive power (VQ) sensitivity matrix in an iterative linear optimizer to calculate the minimum reactive power intervention from PV inverters needed for mitigating over‐voltage without resorting to active power curtailing or requiring step voltage regulator setting changes. The algorithm is validated using the EPRI J1 feeder under an extensive set of realistic use cases and is shown to provide 3x improvement in HC under all scenarios.

Dalal, Dhaval [School of Electrical, Computer, and↗
DOE OSTI2025

Multi-Objective Optimization of Uranium Target Assembly–3: A Comparison of Genetic and Traditional Methods

Commonly produced as a byproduct of uranium fission, 99 Mo is a key medical isotope that is in high demand in the United States. An international goal is to switch from medical isotope production technologies that require highly enriched uranium to medical isotope production technologies that require only low-enriched uranium. Niowave Inc. is contributing to this goal by developing an accelerator-driven subcritical assembly called the Uranium Target Assembly (UTA). This work compares the performance of Dakota’s Multi-Objective Genetic Algorithm (MOGA) against traditional sensitivity analysis in the neutronic optimization of the UTA-3 system. The design objectives are k-eigenvalue (k eff ) and natural uranium fission power, which are directly correlated with the amount of 99 Mo produced. Dakota:MOGA did not perform as well as human engineering ingenuity in optimization studies with high numbers of input parameters, such as fuel rod type selection and fuel rod placement. However, Dakota:MOGA did outperform traditional sensitivity analysis in optimization studies with fewer than 20 parameters and revealed the degree to which each parameter influences the optimal design space for k eff and natural uranium fission power (to a lesser extent). As the design model became more complex in the final stage of design, the computational resources required to calculate the design objective values in the Monte Carlo N-Particle transport code from selected input parameter combinations limited Dakota:MOGA’s performance, and, unfortunately, human intervention was required to discern the optimal design space. In conclusion, future work will attempt to reduce computational resource constraints by incorporating areduced-order neutronics model into the optimization cycle.

Accelerator-driven systems↗