Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “passivating layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Characterization of Engineered Pinholes in Dielectric Stacks of High-Performance Poly-Silicon Passivating Contacts

Passivating contact structures are expected to be implemented in > 50 % of industrially manufactured silicon photovoltaics produced over the next decade. One type of passivating contact utilizes a c-Si/dielectric/doped poly-Si layer stack. In cases where the dielectric layer/s are thick enough to impede tunneling of charge carriers, it was shown that disruptions (pinholes) in the dielectric are required to facilitate transport.[1] Pinholes in SiOx layers have typically been formed via high temperature annealing that allows localized breakup of this layer. This approach has drawbacks; 1) high temperature annealing increases cost and 2) pinhole formation is sensitive to both the SiOx thickness and wafer surface morphology making control of density and dimensions difficult. Recently, an alternative method of pinhole formation relying on metal assisted chemical etching (MACE) was shown to allow control over pinhole areal densities.[2] Such control is critical as both the density and dimensions of the pinholes determine saturation current density and contact resistivity. The contacts formed with the MACE process are known as polysilicon on locally etched oxide or PLEO and also result in low saturation current densities and low contact resistivity due to SiOx passivation and engineered pinhole enabled charge carrier transport, respectively. Photovoltaic devices with efficiencies greater than 20 % have recently been produced with these contacts, demonstrating the viability of contacts with engineered pinholes. Experimentally, preferential local collection of excess charge carriers has been observed and definitively connected to thermally induced pinholes in thick SiOx layers within c-Si/SiOx/poly-Si contact structures.[3] Recent work has shown that enhanced local collection of excess carriers can result from enhanced diffusion of dopants through pinholes in SiOx layers.[4] This study was restricted to simulation and characterization of poly-Si with the same dopant type as the c-Si substrates. In this work we focus our analysis on boron doped poly-Si with different stacks of dielectric layers (PLEO and PLENO where the N refers to a SiNy layer on top of the SiOx) on n-type crystalline silicon. This provides insight into how engineered pinholes affect charge collection across the p-n junction. Like previous observations of locally enhanced carrier transport through thermally induced pinholes, the EBIC images in Figure 1 shows that engineered pinholes in PLENO (1a) and PLEO (1b) also exhibit locally enhanced carrier transport at pinhole locations (bright spots in the images). We will also present detailed correlative nanoscale structural and chemical analysis using TEM imaging and EELS analysis with sample preparation guided by EBIC imaging. This allows us to connect the density and dimensions of engineered pinholes with charge carrier transport and measured photovoltaic device parameters. Our findings will accelerate the adoption of PLEO and PLENO contacts in industrially manufactured photovoltaic devices.

EBIC↗

Hybrid Damping System for an Electronic Equipment Mounting Shelf

The objective of this study was to design and construct a vibration control system for an electronic equipment shelf to be evaluated in the NASA Dryden FTF-11. The vibration control system was a hybrid system which included passive and active damping techniques. Passive damping was fabricated into the equipment shelf using ScothDamp(trademark) damping film and aluminum constraining layers. Active damping was achieved using a two channel active control circuit employing QuickPack(trademark) sensors and actuators. Preliminary Chirp test results indicated passive damping smoothed the frequency response while active damping reduced amplitudes of the frequency response for most frequencies below 500Hz.

Voracek, David↗

Hybrid Damping System for an Electronic Equipment Mounting Shelf

The objective of this study was to design and construct a vibration control system for an electronic equipment shelf to be evaluated in the NASA Dryden FTF-II. The vibration control system was a hybrid system which included passive and active damping techniques. Passive damping was fabricated into the equipment shelf using ScothDamp(trademark) damping film and aluminum constraining layers. Active damping was achieved using a two channel active control circuit employing QuickPack(trademark) sensors and actuators. Preliminary Chirp test results indicated passive damping smoothed the frequency response while active damping reduced amplitudes of the frequency response for most frequencies below 500Hz.

Voracek, David↗

No Evidence for Passivation Effects of Na and K at Grain Boundaries in Polycrystalline Cu(In,Ga)Se2 Thin Films for Solar Cells

Thin-film solar cells based on Cu(In,Ga)Se2 (CIGSe) absorber layers reach conversion efficiencies of above 20%. One key to this success is the incorporation of alkali metals, such as Na and K, into the surface and the volume of the CIGSe thin film. The present work discusses the impact of Na and K on the grain-boundary (GB) properties in CIGSe thin films, i.e., on the barriers for charge carriers, ..phi..b, and on the recombination velocities at the GBs, sGB. First, the physics connected with these two quantities as well as their impact on the device performance are revised, and then the values for the barrier heights and recombination velocities are provided from the literature. The sGB values are measured by means of a cathodoluminescence analysis of Na-/K-free CIGSe layers as well as on CIGSe layers on Mo/sapphire substrates, which are submitted to only NaF or only KF postdeposition treatments. Overall, passivating effects on GBs by neither Na nor K can be confirmed. The GB recombination velocities seem to remain on the same order of magnitude, in average about 10^3-10^4 cm s^-1, irrespective of whether CIGSe thin films are Na-/K-free or Na-/K-containing.

14 SOLAR ENERGY↗

Transparent electrodes in silicon heterojunction solar cells: Influence on contact passivation

Charge carrier collection in silicon heterojunction solar cells occurs via intrinsic/doped hydrogenated amorphous silicon layer stacks deposited on the crystalline silicon wafer surfaces. Usually, both the electron and hole collecting stacks are externally capped by an n-type transparent conductive oxide, which is primarily needed for carrier extraction. Earlier, it has been demonstrated that the mere presence of such oxides can affect the carrier recombination in the crystalline silicon absorber. Here, we present a detailed investigation of the impact of this phenomenon on both the electron and hole collecting sides, including its consequences for the operating voltages of silicon heterojunction solar cells. As a result, we define guiding principles for improved passivating contact design for high-efficiency silicon solar cells.

14 SOLAR ENERGY↗

Modeling of transport in carrier-selective contacts in silicon heterojunction solar cells

High-performance silicon heterojunction (SHJ) solar cells use carrier-selective contact structures based on hydrogentated amorphous Si (a-Si:H) to maximize collection of photogenerated carriers. The high open circuit voltages observed experimentally in SHJ cells require that the carrier-selective contacts provide selectivity and passivation. However, a microscopic understanding of the dynamics of carrier transport through the a-Si layer is currently lacking. In this paper, we explicitly simulate the transport of holes across the a-Si:H(i) layer using a novel kinetic Monte Carlo approach. The hole-selective contact structure investigated in this paper uses p-type doped a-Si:H(p) and intrinsic a-Si:H(i) on an n-type crystalline silicon wafer, where the selectivity is provided by the a-Si:H(p) and the passivation is provided by the a-Si:H(i). However, in addition to the passivation provided by the a-Si:H(i), this layer also creates a potential barrier to the collection of photogenerated holes. There have been experimental studies in the literature that have suggested that multi-phonon processes are the main transport mechanism that assists in the transport of holes across the intrinsic a-Si:H barrier. Simulations presented here show that multi-phonon injection of holes into the a-Si:H(i) layer is the rate limiting step for transport across the a-Si:H(i) layer. Our results indicate that multi-phonon transport is strongly dependent on the electric field at the a-Si:H(i)/c-Si heterointerface as well. Transport simulations presented in this paper are consistent with experimental findings that multi-phonon processes limit transport across the a-Si:H(i) layer and are responsible for photocurrent suppression at the a-Si:H(i)/c-Si heterointerface when these processes are slower than the associated incident hole flux due to photo-excitation.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Ice water path estimation and characterization using passive microwave radiometry

Model computations of top-of-atmospheric microwave brightness temperatures T(B) from layers of precipitation-sized ice of variable bulk density and ice water content (IWC) are presented. It is shown that the 85-GHz T(B) depends essentially on the ice optical thickness. The results demonstrate the potential usefulness of scattering-based channels for characterizing the ice phase and suggest a top-down methodology for retrieval of cloud vertical structure and precipitation estimation from multifrequency passive microwave measurements. Attention is also given to radiative transfer model results based on the multiparameter radar data initialization from the Cooperative Huntsville Meteorological Experiment (COHMEX) in northern Alabama. It is shown that brightness temperature warming effects due to the inclusion of a cloud liquid water profile are especially significant at 85 GHz during later stages of cloud evolution.

Vivekanandan, J.↗

Analysis of Al diffusion processes in TiN barrier layers for the application in silicon solar cell metallization

An evaporated Al layer is known as an excellent rear metallization for highly efficient solar cells, but suffers from incompatibility with a common solder process. To enable solar cell-interconnection and module integration, in this work the Al layer is complemented with a solder stack of TiN/Ti/Ag or TiN/NiV/Ag, in which the TiN layer acts as an Al diffusion barrier. X-ray photoelectron spectroscopy measurements prove that diffusion of Al through the stack and the formation of an Al{sub 2}O{sub 3} layer on the stack's surface are responsible for a loss of solderability after a strong post-metallization anneal, which is often mandatory to improve contact resistance and passivation quality. An optimization of the reactive TiN sputter process results in a densification of the TiN layer, which improves its barrier quality against Al diffusion. However, measurements with X-ray diffraction and scanning electron microscopy show that small grains with vertical grain boundaries persist, which still offer fast diffusion paths. Therefore, the concept of stuffing is introduced. By incorporating oxygen into the grain boundaries of the sputtered TiN layer, Al diffusion is strongly reduced as confirmed by secondary ion mass spectroscopy profiles. A quantitative analysis reveals a one order of magnitude lower Al diffusion coefficient for stuffed TiN layers. This metallization system maintains its solderability even after strong post-metallization annealing at 425 °C for 15 min. This paper thus presents an industrially feasible, conventionally solderable, and long-term stable metallization scheme for highly efficient silicon solar cells.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Trap state passivation improved hot-carrier instability by zirconium-doping in hafnium oxide in a nanoscale n-metal-oxide semiconductor-field effect transistors with high-k/metal gate

This work investigates the effect on hot carrier degradation (HCD) of doping zirconium into the hafnium oxide high-k layer in the nanoscale high-k/metal gate n-channel metal-oxide-semiconductor field-effect-transistors. Previous n-metal-oxide semiconductor-field effect transistor studies demonstrated that zirconium-doped hafnium oxide reduces charge trapping and improves positive bias temperature instability. In this work, a clear reduction in HCD is observed with zirconium-doped hafnium oxide because channel hot electron (CHE) trapping in pre-existing high-k bulk defects is the main degradation mechanism. However, this reduced HCD became ineffective at ultra-low temperature, since CHE traps in the deeper bulk defects at ultra-low temperature, while zirconium-doping only passivates shallow bulk defects.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Zirconium oxide surface passivation of crystalline silicon

This letter reports effective passivation of crystalline silicon (c-Si) surfaces by thermal atomic layer deposited zirconium oxide (ZrO x ). The optimum layer thickness and activation annealing conditions are determined to be 20 nm and 300 °C for 20 min. Cross-sectional transmission electron microscopy imaging shows an approximately 1.6 nm thick SiO x interfacial layer underneath an 18 nm ZrO x layer, consistent with ellipsometry measurements (~20 nm). Capacitance-voltage measurements show that the annealed ZrO x film features a low interface defect density of 1.0 × 10 11 cm -2 eV -1 and a low negative film charge density of -6 × 10 10 cm -2 . Effective lifetimes of 673 μs and 1.1 ms are achieved on p-type and n-type 1 Ω cm undiffused c-Si wafers, respectively, corresponding to an implied open circuit voltage above 720 mV in both cases. The results demonstrate that surface passivation quality provided by ALD ZrO x is consistent with the requirements of high efficiency silicon solar cells.

36 MATERIALS SCIENCE↗

Formation of a strontium buffer layer on Si(001) by pulsed-laser deposition through the Sr/Si(001)(2 × 3) surface reconstruction

The formation of a ½ monolayer (ML) of strontium (Sr) on Si(001) represents the most widely used and effective passivation procedure for the epitaxial growth of strontium titanate (SrTiO{sub 3}) on Si with molecular beam epitaxy (MBE). In the present study, we demonstrate experimentally the possibility of preparing such a buffer layer with the pulsed-laser deposition (PLD) technique. In-situ analysis using reflection high-energy electron diffraction (RHEED) showed surface structure evolution from two-domain (2 × 1) + (1 × 2), exhibited by the bare silicon surface, to a (3 × 2) + (2 × 3) structure at 1/6 ML Sr coverage, which is then replaced by (1 × 2) + (2 × 1) structure at ¼ ML and maintained up to ½ ML coverage. In addition, two different processes for the removal of native silicon dioxide (SiO{sub 2}) layer were studied: thermal and Sr-induced deoxidation process. Annealing above 1100 °C proved to be the most efficient in terms of carbon contamination. The results highlight the possibilities of using the PLD technique for the synthesis of an epitaxial SrTiO{sub 3} layer on Si, needed for the integration of different functional oxides with a Si platform.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Carrier Selective, Passivated Contacts for High Efficiency Silicon Solar Cells based on Transparent Conducting Oxides

We describe the design, fabrication and results of passivated contacts to n-type silicon utilizing thin SiO 2 and transparent conducting oxide layers. High temperature silicon dioxide is grown on both surfaces of an n-type wafer to a thickness <50 Å, followed by deposition of tin-doped indium oxide (ITO) and a patterned metal contacting layer. As deposited, the thin-film stack has a very high J0, contact , and a non-ohmic, high contact resistance. However, after a forming gas anneal, the passivation quality and the contact resistivity improve significantly. The contacts are characterized by measuring the recombination parameter of the contact (J0, contact ) and the specific contact resistivity (ρ contact ) using a TLM pattern. The best ITO/SiO 2 passivated contact in this study has J 0,contact = 92.5 fA/cm 2 and ρ contact = 11.5 mOhm-cm 2 . These values are placed in context with other passivating contacts using an analysis that determines the ultimate efficiency and the optimal area fraction for contacts for a given set of (J0, contact , ρ contact ) values. The ITO/SiO 2 contacts are found to have a higher J0, contact , but a similar ρ contact compared to the best reported passivated contacts.

14 SOLAR ENERGY↗

High-Throughput In-Line Deposition of Silicon Oxide for Polycrystalline Silicon Passivating Contacts

Polycrystalline silicon passivating contacts rely on an ultrathin (1–2 nm) silicon oxide layer to minimize recombination at the wafer/oxide interface and regulate dopant diffusion. Traditionally formed by thermal or chemical oxidation, this oxide is herein replaced by silicon oxide deposited via aerosol impact-driven assembly (AIDA), enabling high wafer-per-hour throughput and precise thickness control. In this study, we show that AIDA coatings conformally cover planar or textured substrates and achieve a SiO x /poly-Si(n) structure with an implied open-circuit voltage (iV oc = 726 mV) and contact saturation current density (J 0 = 8.8 fA/cm 2 ). Furthermore, annealing AIDA SiO x films at elevated temperatures desorbs hydroxyl groups while the stoichiometry transitions toward SiO 2 , improving passivation quality. Together, these results highlight AIDA’s potential for scalable, high-throughput manufacturing of advanced passivating contacts, offering a cost-effective alternative to conventional low-pressure chemical vapor deposition and plasma-enhanced chemical vapor deposition-based silicon and oxide processes.

TOPcon↗

Developing Efficient Perovskite/Silicon Tandem Devices

This project aims at developing highly efficient perovskite/silicon tandem solar cells by developing efficient perovskite top cells, silicon bottom cells, and monolithically integrating the subcells for highly efficient tandem solar cells. The project focused on increasing the efficiency of perovskite solar cells to 20% and understanding related materials science and device physics, as well as developing a compatible bottom high-efficiency c-Si solar cell. The perovskite cells with a wide bandgap of 1.61 eV and 1.84 eV are fabricated by a low-cost, low-temperature, scalable solution process on lower bandgap silicon bottom cells. The bandgaps of perovskite top cells have been tuned between 1.61 eV and 1.84 eV by composition engineering mainly through controlling the halide mixing ratio in perovskite materials. The efficiencies of the wide bandgap perovskite solar cells have been improved to an excellent efficiency of 21.0% for perovskites with a bandgap of 1.63 eV with increased grain size, reduced energy disorder at cathode contact, and defect passivation. We invented a solvent annealing approach with solvent vapor during thermal annealing to enlarge grain size of perovskite film which reduces the charge trap density and improves the device efficiency. Moreover, we discovered that the non-wetting surface could further increase the grain size for perovskite films, because non-wetting surface could prevent the formation of too dense nuclei from heterogeneous nucleation process. We proposed to reduce the energy disorder of organic charge extraction layer to reduce the power loss in perovskite cells. We pioneered defect passivation concept and techniques to suppress the charge non-radiative recombination in perovskite solar cells to boost the efficiency. For the silicon bottom cell development, different from the conventional silicon cell work under full illumination, the light available for the silicon bottom cell in tandem structure is mainly NIR region. We developed a NIR enhanced silicon cell with efficiency of 21.2% by applying a double-layer antireflection coating at the front side and a MgF2 back reflector layer at the rear side. For the perovskite/silicon tandem device, we achieved a highest reported power conversion efficiency of 25.4% in 2018, and further increased the efficiency up to 26.0% in 2019. The research on tandem solar cells focused on reducing reflection loss to <5% at spectrum of 300-1100 nm by antireflection layer, tuning the bandgap of perovskite film for matched current density between sub-cells, and utilizing a ITO layer between perovskite top cell and silicon bottom cell as interconnect layer without Voc loss. Finally, we developed a blading technique to fabricate perovskite films which produces perovskite solar cells with comparable or even superior efficiency to those made by non-scalable spin coating method. This paves the way for scaling up perovskite/silicon tandem solar cells using solution approach.

14 SOLAR ENERGY↗

Scale-Enhanced Magnetism in Exfoliated Atomically Thin Magnetite Sheets

The discovery of ferromagnetism in atomically thin layers at room temperature widens the prospects of 2D materials for device applications. Recently, two independent experiments demonstrated magnetic ordering in two dissimilar 2D systems, CrI 3 and Cr 2 Ge 2 Te 6 , at low temperatures and in VSe 2 at room temperature, but observation of intrinsic room-temperature magnetism in 2D materials is still a challenge. Here a transition at room temperature that increases the magnetization in magnetite while thinning down the bulk material to a few atom-thick sheets is reported. DC magnetization measurements prove ferrimagnetic ordering with increased magnetization and density functional theory calculations ascribe their origin to the low dimensionality of the magnetite layers. Additionally, surface energy calculations for different cleavage planes in passivated magnetite crystal agree with the experimental observations of obtaining 2D sheets from non-van der Waals crystals.

2D Magnetism↗

Impact of Cloud Longwave Scattering on Radiative Fluxes Associated With the Madden-Julian Oscillation in the Indian Ocean and Maritime Continent

Previous studies suggested that cloud longwave radiation contributes to the development and maintenance of the Madden-Julian Oscillation (MJO) and model-based convection is highly sensitive to the radiation scheme. However, currently used radiation schemes do not take cloud longwave scattering into account, resulting in an overestimation of the outgoing longwave radiation (OLR) and an underestimation of the downward longwave flux at the surface. We use combined active and passive satellite cloud property retrievals to quantify the one-layer cloud OLR and heating rate (HR) biases introduced by neglecting cloud longwave scattering in the Indian Ocean and Maritime Continent in the context of MJO, with a focus on its phases 3, 5, and 6. Here, the results show that the satellite-detected one-layer cloud area consists primarily of ice clouds, particularly during the boreal winter in the 4-year study period. An increased ice cloud area fraction of one-layer cloud groups is present up to 5 days before the onset of MJO events. If longwave scattering is neglected, the composite mean OLR overestimation over the one-layer ice cloud area from 5 days before to 4 days after the MJO passage is approximately 3.5 to 5.0 W m –2 . Neglecting longwave scattering also leads to a HR underestimation at cloud base and an overestimation at cloud top, making the base-to-top heating gradient less sharp at the cloud-resolving scale.

54 ENVIRONMENTAL SCIENCES↗

Sensitivities of Large Eddy Simulations of Aerosol Plume Transport and Cloud Response

Abstract Cloud responses to surface‐based sources of aerosol perturbation partially depend on how turbulent transport of the aerosol to cloud base affects the spatial and temporal distribution of aerosol. Here, scenarios of plume injection below a marine stratocumulus cloud are modeled using large eddy simulations coupled to a prognostic bulk aerosol and cloud microphysics scheme. Both passive plumes, consisting of an inert tracer, and active plumes are investigated, where the latter are representative of saltwater droplet plumes such as have been proposed for marine cloud brightening. Passive plume scenarios show higher in‐plume cloud brightness (relative to out‐of‐plume) due to the predominant transport of the passive plume tracer from the near‐surface to the cloud layer within updrafts. These updrafts rise into brighter areas within the cloud deck, even in the absence of an aerosol perturbation associated with an active plume. Comparing albedo at in‐plume to out‐of‐plume locations associates the inert plume with the brightest cloud locations, without any causal effect of the plume on the cloud. Numerical sensitivities are first assessed to establish a suitable model configuration. Then sensitivity to particle injection rate is investigated. Trade‐offs are identified between the number of injected particles and the suppressive effect of droplet evaporation on plume loft and spread. Furthermore, as the near‐field in‐plume brightening effect does not depend significantly on injection rate given a suitable definition of perturbed versus unperturbed regions of the flow, plume area is a key controlling factor on the overall cloud brightening effect of an aerosol perturbation.

54 ENVIRONMENTAL SCIENCES↗