Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optical techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Spectroscopic Determination of Trace Contaminants in High-Purity Oxygen

Oxygen used for extravehicular activities (EVAs) must be free of contaminants because a difference in a few tenths of a percent of argon or nitrogen content can mean significant reduction in available EVA time. These inert gases build up in the extravehicular mobility unit because they are not metabolized or scrubbed from the atmosphere. A prototype optical emission technique capable of detecting argon and nitrogen below 0.1% in oxygen has been developed. This instrument uses a glow discharge in reduced-pressure gas to produce atomic emission from the species present. Because the atomic emission lines from oxygen, nitrogen, and argon are discrete, and in many cases well-separated, trace amounts of argon and nitrogen can be detected in the ultraviolet and visible spectrum. This is a straightforward, direct measurement of the target contaminants, and may lend itself to a device capable of on-orbit verification of oxygen purity. A glow discharge is a plasma formed in a low-pressure (1 to 10 Torr) gas cell between two electrodes. Depending on the configuration, voltages ranging from 200 V and above are required to sustain the discharge. In the discharge region, the gas is ionized and a certain population is in the excited state. Light is produced by the transitions from the excited states formed in the plasma to the ground state. The spectrum consists of discrete, narrow emission lines for the atomic species, and broader peaks that may appear as a manifold for molecular species such as O2 and N2, the wavelengths and intensities of which are a characteristic of each atom. The oxygen emission is dominated by two peaks at 777 and 844 nm.

Hornung, Steven↗
NASA NTRS2014

Push-Pull Locomotion for Vehicle Extrication

For applications in which unmanned vehicles must traverse unfamiliar terrain, there often exists the risk of vehicle entrapment. Typically, this risk can be reduced by using feedback from on-board sensors that assess the terrain. This work addressed the situations where a vehicle has already become immobilized or the desired route cannot be traversed using conventional rolling. Specifically, the focus was on using push-pull locomotion in high sinkage granular material. Push-pull locomotion is an alternative mode of travel that generates thrust through articulated motion, using vehicle components as anchors to push or pull against. It has been revealed through previous research that push-pull locomotion has the capacity for generating higher net traction forces than rolling, and a unique optical flow technique indicated that this is the result of a more efficient soil shearing method. It has now been found that pushpull locomotion results in less sinkage, lower travel reduction, and better power efficiency in high sinkage material as compared to rolling. Even when starting from an "entrapped" condition, push-pull locomotion was able to extricate the test vehicle. It is the authors' recommendation that push-pull locomotion be considered as a reliable back-up mode of travel for applications where terrain entrapment is a possibility.

extrication↗
NASA NTRS2016

Archived 1976-1985 JPL Aircraft SAR Data

This report describes archived data from the Jet Propulsion Laboratory (JPL) aircraft radar expeditions in the mid-1970s through the mid-1980s collected by Ron Blom, JPL Radar Geologist. The dataset was collected during Ron's career at JPL from the 1970s through 2015. Synthetic Aperture Radar (SAR) data in the 1970s and 1980s were recorded optically on long strips of film. SAR imagery was produced via an optical, holographic technique that resulted in long strips of film imagery.

Thompson, Thomas W.↗
NASA NTRS2015

Precision of FLEET Velocimetry Using High-Speed CMOS Camera Systems

Femtosecond laser electronic excitation tagging (FLEET) is an optical measurement technique that permits quantitative velocimetry of unseeded air or nitrogen using a single laser and a single camera. In this paper, we seek to determine the fundamental precision of the FLEET technique using high-speed complementary metal-oxide semiconductor (CMOS) cameras. Also, we compare the performance of several different high-speed CMOS camera systems for acquiring FLEET velocimetry data in air and nitrogen free-jet flows. The precision was defined as the standard deviation of a set of several hundred single-shot velocity measurements. Methods of enhancing the precision of the measurement were explored such as digital binning (similar in concept to on-sensor binning, but done in post-processing), row-wise digital binning of the signal in adjacent pixels and increasing the time delay between successive exposures. These techniques generally improved precision; however, binning provided the greatest improvement to the un-intensified camera systems which had low signal-to-noise ratio. When binning row-wise by 8 pixels (about the thickness of the tagged region) and using an inter-frame delay of 65 microseconds, precisions of 0.5 meters per second in air and 0.2 meters per second in nitrogen were achieved. The camera comparison included a pco.dimax HD, a LaVision Imager scientific CMOS (sCMOS) and a Photron FASTCAM SA-X2, along with a two-stage LaVision HighSpeed IRO intensifier. Excluding the LaVision Imager sCMOS, the cameras were tested with and without intensification and with both short and long inter-frame delays. Use of intensification and longer inter-frame delay generally improved precision. Overall, the Photron FASTCAM SA-X2 exhibited the best performance in terms of greatest precision and highest signal-to-noise ratio primarily because it had the largest pixels.

Peters, Christopher J.↗
NASA NTRS2015

Precision of FLEET Velocimetry Using High-speed CMOS Camera Systems

Femtosecond laser electronic excitation tagging (FLEET) is an optical measurement technique that permits quantitative velocimetry of unseeded air or nitrogen using a single laser and a single camera. In this paper, we seek to determine the fundamental precision of the FLEET technique using high-speed complementary metal-oxide semiconductor (CMOS) cameras. Also, we compare the performance of several different high-speed CMOS camera systems for acquiring FLEET velocimetry data in air and nitrogen free-jet flows. The precision was defined as the standard deviation of a set of several hundred single-shot velocity measurements. Methods of enhancing the precision of the measurement were explored such as digital binning (similar in concept to on-sensor binning, but done in post-processing), row-wise digital binning of the signal in adjacent pixels and increasing the time delay between successive exposures. These techniques generally improved precision; however, binning provided the greatest improvement to the un-intensified camera systems which had low signal-to-noise ratio. When binning row-wise by 8 pixels (about the thickness of the tagged region) and using an inter-frame delay of 65 micro sec, precisions of 0.5 m/s in air and 0.2 m/s in nitrogen were achieved. The camera comparison included a pco.dimax HD, a LaVision Imager scientific CMOS (sCMOS) and a Photron FASTCAM SA-X2, along with a two-stage LaVision High Speed IRO intensifier. Excluding the LaVision Imager sCMOS, the cameras were tested with and without intensification and with both short and long inter-frame delays. Use of intensification and longer inter-frame delay generally improved precision. Overall, the Photron FASTCAM SA-X2 exhibited the best performance in terms of greatest precision and highest signal-to-noise ratio primarily because it had the largest pixels.

Peters, Christopher J.↗
NASA NTRS2016

Estimating the Relative Water Content of Single Leaves from Optical Polarization Measurements

Remotely sensing the water status of plants and the water content of canopies remain long-term goals of remote sensing research. For monitoring canopy water status, existing approaches such as the Crop Water Stress Index and the Equivalent Water Thickness have limitations. The CWSI does not work well in humid regions, requires estimates of the vapor pressure deficit near the canopy during the remote sensing over-flight and, once stomata close, provides little information regarding the canopy water status. The EWI is based upon the physics of water-light interaction, not plant physiology. In this research, we applied optical polarization techniques to monitor the VISNIR light reflected from the leaf interior, R, as well as the leaf transmittance, T, as the relative water content (RWC) of corn (Zea mays) leaves decreased. Our results show that R and T both changed nonlinearly as each leaf dried, R increasing and T decreasing. Our results tie changes in the VISNIR R and T to leaf physiological changes linking the light scattered out of the drying leaf interior to its relative water content and to changes in leaf cellular structure and pigments. Our results suggest remotely sensing the physiological water status of a single leaf and perhaps of a plant canopy might be possible in the future. However, using our approach to estimate the water status of a leaf does not appear possible at present, because our results display too much variability that we do not yet understand.

Leaf Reflectance↗
NASA NTRS2018

Navigation Requirements Development and Performance Assessment of a Martian Ascent Vehicle

To support development of Martian Ascent Vehicles, analysis tools are needed to support the development of Guidance, Navigation, and Control requirements. This paper presents a focused approach to Navigation analysis to capture development of requirements on initial state knowledge and inertial sensor capabilities. A simulation and analysis framework was used to assess the capability of a range of sensors to operate inertially along a range of launch trajectories. The baseline Martian Ascent Vehicle was used as the input for optimizing a set of trajectories from each launch site. These trajectories were used to perform Monte Carlo analysis dispersing error sensor terms and their effects on integrated vehicle performance. Additionally, this paper provides insight into the use of optical navigation techniques to assess state determination and the potential to use observations of local extraplanetary bodies to estimate state. This paper provides an initial level of performance assessment of navigation components to support continued requirements development of a Martian Ascent Vehicle with applications to both crew and sample return missions.

Anzalone, Evan J.↗
NASA NTRS2018

Development of a Mars Lidar (MARLI) for Measuring Wind and Aerosol Profiles from Orbit

Our understanding of the Mars atmosphere and the coupled atmospheric processes that drive its seasonal cycles is limited by a lack of observation data, particularly measurements that capture diurnal and seasonal variations on a global scale. As outlined in the 2011 Planetary Science Decadal Survey and the recent Mars Exploration Program Analysis Group(MEPAG) Goals Document, near-polar-orbital measurements of height-resolved aerosol backscatter and wind profiles area high-priority for the scientific community and would be valuable science products as part of a next-generation orbital science package. To address these needs, we have designed and tested a breadboard version of a direct detection atmospheric wind lidar for Mars orbit. It uses a single-frequency, seeded Nd:YAG laser ring oscillator operating at 1064nm (4 kHz repetition rate), with a 30-ns pulse duration amplified to 4 mJ pulse energy. The receiver uses a Fabry-Perotetalon as part of a dual-edge optical discrimination technique to isolate the Doppler-induced frequency shift of the back scattered photons. To detect weak aerosol backscatter profiles, the instrument uses a 4x4 photon-counting HgCdTeAPD detector with a 7 MHz bandwidth and < 0.4 fW/Hz(exp 1/2) noise equivalent power. With the MARLI lidar breadboard instrument, we were able to measure Doppler shifts continuously between 1 and 30 m/s by using a rotating chopper wheel to impart a Doppler shift to incident laser pulses. We then coupled the transmitter and receiver systems to a laser ranging telescope at the Goddard Geophysical and Astronomical Observatory (GGAO) to measure backscatter and Doppler wind profiles in the atmosphere from the ground. We measured a 5.3 ± 0.8 m/s wind speed from clouds in the planetary boundary layer at a range of 4 to 6 km. This measurement was confirmed with a range-over-time measurement to the same clouds as well as compared to EMC meteorological models. Here we describe the lidar approach and the breadboard instrument, and report some early results from ongoing field experiments.

Cremons, Daniel R.↗
NASA NTRS2019

Applying Optical Diagnostics to Study Aircraft Gas Turbine Combustor Performance

This is for an invited lecture at Cleveland State University for a combustion course. The presentation gives an overview of some of the optical diagnostic techniques the Combustion Branch uses to characterize research fuel injection concepts to reduce emissions. Examples are provided that come from previously presented conference papers

Hicks, Yolanda R.↗
NASA NTRS2020

Delta Cp RMS and Shadowgraph Data from t11-0377 (ATAT)

The plots included in this NF-1676 were collected during a recent wind tunnel test at the 11’x11’ Transonic test section of the Unitary Plan Wind Tunnel. The data is not SBU or ITAR since the images are qualitative and do not share model measurements. The on-body data is Delta Cp RMS. The off-body data is Time-Variance of the Shadowgraph intensity. No tunnel conditions other than Mach, Alpha, Beta, and Tunnel Drive Speed (RPM) are shared. Most importantly, dynamic pressure and static pressure are not included.

Aerodynamics↗
NASA NTRS2021

Phase Diagram, Melt Growth and Characterization of Cd0.8Zn0.2Te Crystals for X-Ray Detector

In this study, the solidus curve of the Cd0.8Zn0.2Te homogeneity range was constructed from the partial pressure measurements by optical absorption technique which provided the information of the melt growth parameters to process crystals with the required electrical resistivity. The melt growth of Cd0.8Zn0.2Te crystals were then processed by directional solidification under controlled Cd overpressure. During the growth experiments, several procedures have been developed to improve the crystalline quality: (1) minimizing the contamination of impurities (2) improving the structural defects and (3) minimizing the Te-precipitates within the grown crystals to enhance charge transport properties. Additionally, the thermal conductivity, electrical conductivity, and Seebeck coefficient of a vapor-grown CdTe and two melt-grown Cd0.8Zn0.2Te crystals were measured between 190oC and 780oC to provide an in-depth understanding of the thermal and electrical conduction mechanisms of the crystals as well as the prospect of its thermoelectric applications.

x-ray detector↗
NASA NTRSDate not supplied

Validation of the Corcos Model for the Space Launch System using Unsteady Pressure Sensitive Paint

During atmospheric ascent launch vehicles (LVs) experience large dynamic loads at transonic conditions where aerodynamic buffet is most critical. To estimate buffet loads, coupled loads analyses typically utilize suitable forcing functions, called buffet forcing functions (BFFs). One of the key buffet environment contributors is the turbulent boundary layer (TBL) on the LV outer skin. The TBL-induced fluctuating pressures can be estimated using the widely-accepted Corcos model. In the context of transonic buffet, the performance of this model is not well established, partly because of lack of data. To fill this gap, NASA recently acquired extremely high-spatial-density data for the Space Launch System (SLS) vehicle, using the unsteady pressure sensitive paint (uPSP) optical measurement technique. A methodology is developed for validation of the Corcos model using these unique data, with a focus on the LV-design application. The model hypotheses are verified and the model parameters are empirically tuned. For selected panels on the vehicle, BFF coherence factors are derived based on the Corcos model and the associated panel BFFs are compared to uPSP data. It is shown that the modeled BFFs are in agreement with direct integration of uPSP data, except for regions where pressure fluctuations are spatially nonuniform. In those regions, the Corcos-based BFFs exhibit inherent limitations of BFF estimation methods that rely on discrete pressure measurements.

buffet↗
NASA NTRSDate not supplied

Validation of the Corcos Model for the Space Launch System using Unsteady Pressure Sensitive Paint

During atmospheric ascent launch vehicles (LVs) experience large dynamic loads at transonic conditions where aerodynamic buffet is most critical. To estimate buffet loads, coupled loads analyses typically utilize suitable forcing functions, called buffet forcing functions (BFFs). One of the key buffet environment contributors is the turbulent boundary layer (TBL) on the LV outer skin. The TBL-induced fluctuating pressures can be estimated using the widely-accepted Corcos model. In the context of transonic buffet, the performance of this model is not well established, partly because of lack of data. To fill this gap, NASA recently acquired extremely high-spatial-density data for the Space Launch System (SLS) vehicle, using the unsteady pressure sensitive paint (uPSP) optical measurement technique. A methodology is developed for validation of the Corcos model using these unique data, with a focus on the LV-design application. The model hypotheses are verified and the model parameters are empirically tuned. For selected panels on the vehicle, BFF coherence factors are derived based on the Corcos model and the associated panel BFFs are compared to uPSP data. It is shown that the modeled BFFs are in agreement with direct integration of uPSP data, except for regions where pressure fluctuations are spatially nonuniform. In those regions, the Corcos-based BFFs exhibit inherent limitations of BFF estimation methods that rely on discrete pressure measurements.

buffet↗
NASA NTRS2022

Impact of Future Low-Emissions Combustor Technology on Acoustic Scaling Laws

The overall goal of a recent research project at the Raytheon Technologies Research Center, under National Aeronautics and Space Administration sponsorship, was to develop a first-ofits-kind database of detailed unsteady measurements characterizing noise sources of far-term advanced low-emissions aero-combustors. The program addressed the need for fundamental combustion-noise experiments which, in the near term, enable improvements to reduced-order models for use in system level noise assessments at the preliminary design stage for advanced air transport vehicles. In addition, optical measurement techniques were refined and validated for usage at the higher pressures and temperatures relevant to future combustor designs. In the long term, results from this program can be utilized to validate high-fidelity prediction methods suited for detailed multi-disciplinary acoustics/emissions combustor design. This paper concentrates on one aspect of the overall project, namely an examination of the legacy scaling laws for broadband combustor noise.

aeroacoustics, turbomachinery noise, combustor noi↗
NASA NTRSDate not supplied

Impact of Future Low-Emissions Combustor Technology on Acoustic Scaling Laws

The work is a summary and further analysis of unlimited-rights acoustic data acquired under NRA Contract NNC16CA39C (September 2016 - November2019) with United Technologies (now Raytheon Technologies) Research Center, East Hartford, Connecticut. NASA/CR-20205011099/VOL1, https://ntrs.nasa.gov/citations/20205011099. The overall goal of the Contract was to develop a first-of-its- kind database of detailed unsteady measurements characterizing noise sources of far-term advanced low-emissions aero-combustors. The program addressed the need for fundamental combustion-noise experiments which, in the near term, enable improvements to reduced-order models for use in system level noise assessments at the preliminary design stage for advanced air transport vehicles. In addition, optical measurement techniques were refined and validated for usage at the higher pressures and temperatures relevant to future combustor designs. In the long term, results from this program can be utilized to validate high-fidelity prediction methods suited for detailed multi-disciplinary acoustics/emissions combustor design. This presentation concentrates on one aspect of the overall project, namely an examination of the legacy scaling laws for broadband combustor noise.

aeroacoustics, turbomachinery noise, combustor noi↗
NASA NTRSDate not supplied

Infrared Reflection Removal in Wind Tunnels Using Polarization Theory

Infrared radiometry with infrared cameras allows for high spatial resolution, noncontact measurements in wind tunnel experiments and has been increasingly used to visualize flow features. Reflections from test section walls present a major challenge in collecting these measurements as it is difficult or impossible to separate them from the true model emission signal. This paper outlines a method to quantitatively remove specular reflections using polarization theory for materials common in the Unitary Plan Wind Tunnel. The method was however ultimately ineffective due to unexpected diffuse reflection and was unable to remove the specular reflection. The experiment provided insight into ways that polarization could be utilized to improve data collection capabilities of optical measurement techniques in wind tunnel settings.

Infrared↗
NASA NTRS2023

Space Launch System Unsteady Forces Developed from Unsteady-Pressure-Sensitive-Paint–Based Corcos Model Parameters

During atmospheric ascent, launch vehicles (LVs) experience large dynamic loads at transonic conditions where aerodynamic buffet is most critical. To estimate buffet loads, coupled loads analyses typically utilize suitable forcing functions, called buffet forcing functions (BFFs). One of the key buffet environment contributors is the turbulent boundary layer (TBL) on the LV outer skin. The TBL-induced fluctuating pressures can be estimated using the widely-accepted Corcos model. In the context of transonic buffet, the performance of this model is not well established, partly because of lack of data. To fill this gap, NASA recently acquired extremely high-spatial-density data for the Space Launch System (SLS) vehicle, using the unsteady pressure sensitive paint (uPSP) optical measurement technique. A methodology is developed for validation of the Corcos model using these unique data, with a focus on the LV-design application. The model hypotheses are verified and the model parameters are empirically tuned. For selected panels on the vehicle, BFF coherence factors are derived based on the Corcos model and the associated panel BFFs are compared to uPSP data. It is shown that the modeled BFFs are in agreement with direct integration of uPSP data, except for regions where pressure fluctuations are spatially nonuniform. In those regions, the Corcos-based BFFs exhibit inherent limitations of BFF estimation methods that rely on discrete pressure measurements.

buffet↗
NASA NTRSDate not supplied

Designing the Imaging and Breadboard System for FBCE-TL Project

This presentation outlines the support work done on designing the imaging and breadboard system of the Transfer Line (TL) project, which is the third module for the Flow Boiling and Condensation Experiment (FBCE) operating in the Fluids Integrated Rack on-board the International Space Station (ISS). The goal of the FBCE is to serve as a facility for flow boiling and condensation investigating two-phase flow and heat transfer data in microgravity. The TL module aims use existing FBCE hardware to study cryogenic chilldown, a large component of cryogenic propellant tank transfer research. The TL test module will perform chilldown studies with normal-perfluorohexane (nPFH), a cryogenic simulant, flowing through a super-heated line, which is heated through the process of Joule-heating. SolidWorks and Creo were used to create electrically conductive pipe junctions that connect and seal several Indium Tin Oxide (ITO) coated sapphire tube sections together to allow for low leak probability fluid flow and circumferentially uniform electrical current density. It is necessary to understand and calculate the thermal expansion of the tubing sections such that the junctions would not leak at anticipated operating temperatures and pressures, would maintain electrical contact, and not crack the crystalline tubes. Optical imaging techniques were used to build an experimentally validated image remapping process for flight-like setups of cylindrical tubes. Then MATLAB was used to create an algorithm that distorts an image based on the refraction of light passing through the mediums we were imaging through to accurately visualize the cryogenic chilldown that is of scientific interest. This research will assist NASA to move forward with long-duration spaceflight missions where knowledge of efficient heat transfer processes becomes more critical.

imaging system↗