SEARCH · Engineering Papers

Results for “model testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

All sources NASA NTRS DOE OSTI

NASA NTRS1984

Conceptual design of a noncontacting power transfer device for the ASPS Vernier system

The conceptual of electrical power transfer across a magnetically controlled gap as discussed for several years. The design represents the culmination of the first serious attempt to design a very low force, noncontracting power transfer mechanism. The electromagnetic device advanced herein is an ironless, translatable secondary transformer in which one of the two coils is fixed to the entire magnetic core. The second coil is free to move within the core over the full range of motions required. The specific application considered for this design was the Vernier subsystem of the Annular Suspension and Pointing System (ASPS). The development of and rationale for the electromagnetics design is presented. Similar documentation is provided for the Electronics Design. The Appendices detail the results of small scale model tests, disturbance force calculations, the baseline transformer fabrication drawings, the AVS Converter Parts List, and model schematic diagrams.

Kroeger, J.↗

NASA NTRS1983

Additional flow field studies of the GA(W)-1 airfoil with 30-percent chord Fowler flap including slot-gap variations and cove shape modifications

Experimental measurements were made to determine the effects of slot gap opening and flap cove shape on flap and airfoil flow fields. Test model was the GA(W)-1 airfoil with 0.30c Fowler flap deflected 35 degrees. Tests were conducted with optimum, wide and narrow gaps, and with three cove shapes. Three test angles were selected, corresponding to pre-stall and post-stall conditions. Reynolds number was 2,200,000 and Mach number was 0.13. Force, surface pressure, total pressure, and split-film turbulence measurements were made. Results were compared with theory for those parameters for which theoretical values were available.

Wentz, W. H., Jr.↗

NASA NTRS1990

Modeling of near-wall turbulence

An improved k-epsilon model and a second order closure model is presented for low Reynolds number turbulence near a wall. For the k-epsilon model, a modified form of the eddy viscosity having correct asymptotic near wall behavior is suggested, and a model for the pressure diffusion term in the turbulent kinetic energy equation is proposed. For the second order closure model, the existing models are modified for the Reynolds stress equations to have proper near wall behavior. A dissipation rate equation for the turbulent kinetic energy is also reformulated. The proposed models satisfy realizability and will not produce unphysical behavior. Fully developed channel flows are used for model testing. The calculations are compared with direct numerical simulations. It is shown that the present models, both the k-epsilon model and the second order closure model, perform well in predicting the behavior of the near wall turbulence. Significant improvements over previous models are obtained.

Shih, T. H.↗

NASA NTRS1925

Propeller scale effect and body interference

This note shows that the main part of the discrepancy between full flight propeller performance and the performance of models in a wind tunnel is due to a scale effect, and that a minor part is caused by body interference. Analyses are made of propeller performances on several standard airplanes, and the actual brake horsepower compared with the power as calculated from model test data. The calculated power is based on that absorbed by a wind tunnel propeller model which is geometrically similar to the full scale propeller and is operating under the same ratio of V/nD.

Weick, Fred E↗

NASA NTRS2006

Adjoint Method and Predictive Control for 1-D Flow in NASA Ames 11-Foot Transonic Wind Tunnel

This paper describes a modeling method and a new optimal control approach to investigate a Mach number control problem for the NASA Ames 11-Foot Transonic Wind Tunnel. The flow in the wind tunnel is modeled by the 1-D unsteady Euler equations whose boundary conditions prescribe a controlling action by a compressor. The boundary control inputs to the compressor are in turn controlled by a drive motor system and an inlet guide vane system whose dynamics are modeled by ordinary differential equations. The resulting Euler equations are thus coupled to the ordinary differential equations via the boundary conditions. Optimality conditions are established by an adjoint method and are used to develop a model predictive linear-quadratic optimal control for regulating the Mach number due to a test model disturbance during a continuous pitch

Nguyen, Nhan↗

NASA NTRSDate not supplied

Acoustic Testing of the Joby Aviation Propeller in the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel

The advanced air mobility sector has progressed in recent years with electric vertical take-Off and landing vehicles at the forefront. In response, the NASA Advanced Air Mobility Project has initiated the Advanced Air Mobility National Campaign to partner with industry to progress this emerging market. This resulted in NASA’s Revolutionary Vertical Lift Technology project to participate to progress research efforts for software tool validation for these advanced air mobility vehicle configurations. Noise has been identified as one of the main obstacles to succeeding in this emerging market for community acceptance. To further understand electric vertical take-Off and landing vehicle noise, an isolated Joby Aviation S4 propeller was tested in the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel to aid in providing high quality performance, loads, and acoustic data. Details of test hardware and setup are described with a focus on acoustics, which includes facility, test model, microphone locations, and data acquisition system details. Additionally, the data processing techniques and completed test matrix for acoustic points are provided. To aid in identifying potential acoustic reflections, an acoustic reflection test was performed prior to the start of the test and highlighted the presence of reflections at every microphone location. Acoustic results are provided for various flight regimes for sweeps of blade pitch, RPM, flow angle, and wind speed. These results show an optimum RPM for a specific thrust level for noise, and further reductions in RPM can increase noise levels. This dataset will be used to evaluate and improve computational tools.

Aviation Propeller↗

NASA NTRS1974

Helicopter derivative identification from analytic models and flight test data

Recent results of stability derivative identification from helicopter analytic models and flight test data are presented. Six and nine degree-of-freedom (DOF) linear models are identified from an analytic nonlinear helicopter simulation using a least square technique. The identified models are compared with the convectional partial differentiation method for obtaining derivatives to form the basis for interpretation of derivatives identified from flight data. Six degree-of-freedom models are identified from CH-53A and CH-54B flight data, using an extended Kalman filter modified to process several maneuvers simultaneously. The a priori derivative estimate is obtained by optimal filtering of the data and then using a least square method. The results demonstrate that a six DOF identified model is sufficient to determine the low frequency modes of motion, but a nine DOF rotor/body model is necessary for proper representation of short-term response.

Molusis, J. H.↗

NASA NTRS1994

Conceptual design and analysis of a dynamic scale model of the Space Station Freedom

This report documents the conceptual design study performed to evaluate design options for a subscale dynamic test model which could be used to investigate the expected on-orbit structural dynamic characteristics of the Space Station Freedom early build configurations. The baseline option was a 'near-replica' model of the SSF SC-7 pre-integrated truss configuration. The approach used to develop conceptual design options involved three sets of studies: evaluation of the full-scale design and analysis databases, conducting scale factor trade studies, and performing design sensitivity studies. The scale factor trade study was conducted to develop a fundamental understanding of the key scaling parameters that drive design, performance and cost of a SSF dynamic scale model. Four scale model options were estimated: 1/4, 1/5, 1/7, and 1/10 scale. Prototype hardware was fabricated to assess producibility issues. Based on the results of the study, a 1/4-scale size is recommended based on the increased model fidelity associated with a larger scale factor. A design sensitivity study was performed to identify critical hardware component properties that drive dynamic performance. A total of 118 component properties were identified which require high-fidelity replication. Lower fidelity dynamic similarity scaling can be used for non-critical components.

Davis, D. A.↗

NASA NTRS1997

Qualitative Flow Visualization of a 110-N Hydrogen/Oxygen Laboratory Model Thruster

The flow field inside a 110 N gaseous hydrogen/oxygen thruster was investigated using an optically accessible, two-dimensional laboratory test model installed in a high altitude chamber. The injector for this study produced an oxidizer-rich core flow, which was designed to fully mix and react inside a fuel-film sleeve insert before emerging into the main chamber section, where a substantial fuel film cooling layer was added to protect the chamber wall. Techniques used to investigate the flow consisted of spontaneous Raman spectra measurements, visible emission imaging, ultraviolet hydroxyl spectroscopy, and high speed schlieren imaging. Experimental results indicate that the oxygen rich core flow continued to react while emerging from the fuel-film sleeve, suggesting incomplete mixing of the hydrogen in the oxygen rich core flow. Experiments also showed that the fuel film cooling protective layer retained its integrity throughout the straight section of the combustion chamber. In the converging portion of the chamber, however, a turbulent reaction zone near the wall destroyed the integrity of the film layer, a result which implies that a lower contraction angle may improve the fuel film cooling in the converging section and extend the hardware lifetime.

deGroot, Wim A.↗

NASA NTRS1972

Flight and wind tunnel investigation of the effects of Reynolds number on installed boattail drag at subsonic speeds

A flight and wind tunnel investigation was conducted to determine the effects of Reynolds number on the installed boattail drag of an underwing nacelle. Tests were run on a modified F-106B aircraft and 0.05 and 0.22 scale wind tunnel models. Tests were conducted at Mach numbers of 0.6 and 0.9 and over a 16 to 1 range of Reynolds numbers. Highest drag was obtained at intermediate Reynolds numbers corresponding to about the lowest flight values and that of the 0.22 scale model. Significantly lower drag was obtained at both higher and lower Reynolds numbers.

Chamberlin, R.↗

NASA NTRS1973

Flight and wind tunnel investigation of the effects of Reynolds number on installed boattail drag at subsonic speeds.

Chamberlin, R.↗

NASA NTRS1961

Preliminary Base Pressures Obtained from the X-15 Airplane at Mach Numbers from 1.1 to 3.2

Base pressure measurements have been made on the fuselage, 10 deg.-wedge vertical fin, and side fairing of the X-15 airplane. Data are presented for Mach numbers between 1.1 and 3.2 for both powered and unpowered flight. Comparisons are made with data from small-scale-model tests, semiempirical estimates, and theory. The results of this preliminary study show that operation of the interim rocket engines (propellant flow rate approximately 70 lb/sec) reduces the base drag of the X-15 by 25 to 35 percent throughout the test Mach number range. Values of base drag coefficient for the side fairing and fuselage obtained from X-15 wind-tunnel models were adequate for predicting the overall full-scale performance of the test airplane. The leading-edge sweep of the upper movable vertical fin was not an important factor affecting the fin base pressure. The power-off base pressure coefficients of the upper movable vertical fin (a 10 deg. wedge with chord-to-thickness ratio of 5.5 and semispan-to-thickness ratio of 3.2) are in general agreement with the small-scale blunt-trailing-edge-wing data of several investigators and with two-dimensional theory.

Saltzman, Edwin J.↗

NASA NTRS2005

Dynamics Impact Tolerance of Shuttle RCC Leading Edge Panels Using LS-DYNA

This paper describes a research program conducted to enable accurate prediction of the impact tolerance of the shuttle Orbiter leading-edge wing panels using physics-based codes such as LS-DYNA, a nonlinear, explicit transient dynamic finite element code. The shuttle leading-edge panels are constructed of Reinforced-Carbon-Carbon (RCC) composite material, which is used because of its thermal properties to protect the shuttle during reentry into the Earth's atmosphere. Accurate predictions of impact damage from insulating foam and other debris strikes that occur during launch required materials characterization of expected debris, including strain-rate effects. First, analytical models of individual foam and RCC materials were validated. Next, analytical models of foam cylinders impacting 6- in. x 6-in. RCC flat plates were developed and validated. LS-DYNA pre-test models of the RCC flat plate specimens established the impact velocity of the test for three damage levels: no-detectable damage, non-destructive evaluation (NDE) detectable damage, or visible damage such as a through crack or hole. Finally, the threshold of impact damage for RCC on representative Orbiter wing panels was predicted for both a small through crack and for NDE-detectable damage.

Fasanella, Edwin L.↗

NASA NTRS2003

Aeroservoelastic Model Validation and Test Data Analysis of the F/A-18 Active Aeroelastic Wing

Model validation and flight test data analysis require careful consideration of the effects of uncertainty, noise, and nonlinearity. Uncertainty prevails in the data analysis techniques and results in a composite model uncertainty from unmodeled dynamics, assumptions and mechanics of the estimation procedures, noise, and nonlinearity. A fundamental requirement for reliable and robust model development is an attempt to account for each of these sources of error, in particular, for model validation, robust stability prediction, and flight control system development. This paper is concerned with data processing procedures for uncertainty reduction in model validation for stability estimation and nonlinear identification. F/A-18 Active Aeroelastic Wing (AAW) aircraft data is used to demonstrate signal representation effects on uncertain model development, stability estimation, and nonlinear identification. Data is decomposed using adaptive orthonormal best-basis and wavelet-basis signal decompositions for signal denoising into linear and nonlinear identification algorithms. Nonlinear identification from a wavelet-based Volterra kernel procedure is used to extract nonlinear dynamics from aeroelastic responses, and to assist model development and uncertainty reduction for model validation and stability prediction by removing a class of nonlinearity from the uncertainty.

Brenner, Martin J.↗

NASA NTRS2008

Dynamic Impact Tolerance of Shuttle RCC Leading Edge Panels using LS-DYNA

This paper describes a research program conducted to enable accurate prediction of the impact tolerance of the shuttle Orbiter leading-edge wing panels using 'physics-based- codes such as LS-DYNA, a nonlinear, explicit transient dynamic finite element code. The shuttle leading-edge panels are constructed of Reinforced-Carbon-Carbon (RCC) composite material, which issued because of its thermal properties to protect the shuttle during re-entry into the Earth's atmosphere. Accurate predictions of impact damage from insulating foam and other debris strikes that occur during launch required materials characterization of expected debris, including strain-rate effects. First, analytical models of individual foam and RCC materials were validated. Next, analytical models of individual foam cylinders impacting 6-in. x 6-in. RCC flat plates were developed and validated. LS-DYNA pre-test models of the RCC flat plate specimens established the impact velocity of the test for three damage levels: no-detectable damage, non-destructive evaluation (NDE) detectable damage, or visible damage such as a through crack or hole. Finally, the threshold of impact damage for RCC on representative Orbiter wing panels was predicted for both a small through crack and for NDE-detectable damage.

Fasanella, Edwin↗

NASA NTRS1985

Comparative study of Suits and SAIL canopy reflectance models

A detailed understanding of the relationships between the canopy reflectance and the characteristics of canopy elements is an important factor for the full exploitation of the potential of remote sensing from aircraft and spacecraft altitudes to map vegetation and estimate key agronomic parameters such as the leaf area index (LAI) and biomass (BM). Suits (1972) idealized the canopy geometry by replacing each plant component with three orthogonal projections of that component. Verhoeff and Bunnik (1981) extended the Suits model, henceforth called the SAIL (Scattering from Arbitrarily Inclined Leaves) model, by removing certain constraints. The present investigation is concerned with an evaluation of the performance of the Suits and SAIL models, taking into account two data sets on soybean and corn. It was found that the tested models have significant deficiencies. However, the performance of the SAIL model is better than that of the Suits model because it provides a more realistic description of the canopy architecture.

Badhwar, G. D.↗

NASA NTRS1987

Model 360 rotor test at DNW - Review of performance and blade airload data

The results of tests on a pressure gage instrumented model rotor, performed at the Duits Nederlandse Windtunnel (DNW) are discussed. The rotor, which was a 1/5 scale model of the Boeing Vertol model 360 rotor, was tested both in the anechoic open jet test section, and in the 8 x 6 m closed test section of the DNW. The wind tunnel, the blade instrumentation, and the test conditions are described, and data on rotor performance, blade and control loads, and blade-pressure and acoustic measurements are presented.

Dadone, Leo↗

NASA NTRS1995

Vibration damping of the Cassini spacecraft structure

Cassini is a large robotic spacecraft currently under development at the Jet Propulsion Laboratory (JPL) whose interplanetary scientific mission is to explore Saturn, its ring, and its moons. Cassini is scheduled to launch on a Titan IV rocket with a Centaur upper stage booster, and will be protected during ascent through the atmosphere by a lightweight aluminum payload fairing (PLF). As a result of the extreme noise levels generated by the powerful Titan IV at liftoff, and the acoustic transparency of the PLF, Cassini is predicted to experience sever acoustic levels. Furthermore, the high acoustic levels, coupled with the size and configuration of the spacecraft, will induce unacceptable random vibration levels on the structure and critical spacecraft components. Studies showed that the use of Tuned Vibration Absorbers (TVAs) would be effective in reducing vibration. A series of reverberant acoustic tests were performed on a partial development test model (DTM) of Cassini to evaluate the effectiveness of TVAs in reducing the structural vibration. The test results showed that significant vibration attenuation was achieved.

vibration damping↗