Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “load response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Aircraft Cargo Compartment Fire Test Simulation Program

The objective of the test was to assess fire containment and fire extinguishment in the cargo by reducing the ventilation through the cargo compartment. Parameters which were measured included ignition time, burnthrough time, and physical damage to the cargo liner, composition of selected combustible gases, temperature-time histories, heat flux, and detector response. The ignitor load was made of a typical cargo consisting of filled cardboard cartons occupying 50% of the compartment volume.

Blumke, R. E.↗
NASA NTRS1977

Treatment of low strains and long hold times in high temperature metal fatigue by strainrange partitioning

A procedure for treating creep-fatigue for low strainranges and long hold times is outlined. A semi-experimental approach, wherein several cycles of the imposed loading is actually applied to a specimen in order to determine the stable hysteresis loop, can be very useful in the analysis. Because such tests require only a small fraction of the total failure time, they are not inherently prohibitive if experimental equipment is available. The need for accurate constitutive equations is bypassed because the material itself acts to translate the imposed loading into the responsive hysteresis loops. When strainrange partitioning has been applied in such cases very good results have been obtained.

Manson, S. S.↗
NASA NTRS1978

The viscoelastic stiffness model of seismicity

A viscoelastic stiffness model of seismicity is developed by introducing a viscoelastic element into the stiffness model for fault dynamics. The introduction of this element permits modeling of transient anelastic deformations in response to stress loading and relaxation and provides a mechanism for partial stress recovery following an earthquake. As a consequence, several phenomena not present in elastic stiffness theory emerge. These include postseismic creep, foreshocks, and aftershocks. Numerical simulations of fault motion also reveal episodes of stable sliding, tertiary creep preceeding earthquakes, and long-term aseismic creep.

Cohen, S. C.↗
NASA NTRS1979

Path dependence of J in three numerical examples

Three cracked geometries are studied with the aid of a new finite element model. The procedure employs a variable singularity at the crack tip that tracks changes in the material response during the loading process. Two of the problems are tension-loaded center-crack panels and the other is a three-point bend specimen. Results usually agree with other numerical and analytical analyses, except the finding that J is path dependent as a substantial plastic zone develops. Credible J values are obtained near the crack tip and J shows a significant increase as the radius of J path increases over two orders of magnitude. Incremental and deformation theories are identical provided the stresses exhibit proportionality found in the far field stresses but not near the tip.

Karabin, M. E., Jr.↗
NASA NTRS1980

Assessment of oxygen and carbogen therapy effect in Meniere's disease according to clinical and electroencephalographic data

The method of constructing fields on the basis of EEG data gives a quantitative characterization of bioelectrical activity. Fields of average rates of the change of potentials in healthy people have a well defined configuration, where the greatest rates are found in the occipital zones, lower in the frontal and parietal, and least in the temporal zones. In response to functional loads the form of the field remains the same because of a synchronous change in the average rates in both hemispheres of the cerebrum to the same extent. The configuration of the fields of background bioelectric activity of the cerebrum in people with Meniere's disease is not uniform. On the basis of this investigation, a clear correlation was found between the subjective sensations of patients during oxygen and carbogen therapy and the changes in the spatial characteristics of the field of potentials of the cerebrum. This correlation makes it possible to objectively identify the nature of the vascular disturbances in Meniere's disease, develop a pathogenetic treatment plan, and evaluate its effectiveness.

Boronoyev, A. B.↗
NASA NTRS1981

Comparison of upwind and downwind rotor operations of the DOE/NASA 100-kW Mod-O wind turbine

Three aspects of the test results are compared: rotor blade bending loads, rotor teeter response, and nacelle yaw moments. As a result of the tests, it is shown that while mean flatwise bending moments were unaffected by the placement of the rotor, cyclic flatwise bending tended to increase with wind speed for the downwind rotor while remaining somewhat uniform with wind speed for the upwind rotor, reflecting the effects of increased flow disturbance for a downwind rotor. Rotor teeter response was not significantly affected by the rotor location relative to the tower, but appears to reflect reduced teeter stability near rated wind speed for both configurations. Teeter stability appears to return above wind speed, however. Nacelle yaw moments are higher for the upwind rotor but do not indicate significant design problems for either configuration.

Glasgow, J. C.↗
NASA NTRS1981

Comparison of upwind and downwind rotor operation of the DOE/NASA 100-kW MOD-0 wind turbine

Tests were conducted on a 38m diameter horizontal axis wind turbine, which had first a rotor downwind of the supporting truss tower and then upwind of the tower. Aside from the placement of the rotor and the direction of rotation of the drive train, the wind turbine was identical for both tests. Three aspects of the test results are compared: rotor blade bending loads, rotor teeter response, and nacelle yaw moments. As a result of the tests, it is shown that while mean flatwise bending moments were unaffected by the placement of the rotor, cyclic flatwise bending tended to increase with wind speed for the downwind rotor while remaining somewhat uniform with wind speed for the upwind rotor, reflecting the effects of increased flow disturbance for downwind rotor. Rotor teeter response was not significantly affected by the rotor location relative to the tower, but appears to reflect reduced teeter stability near rated wind speed for both configurations. Teeter stability appears to return above rated wind speed, however. Nacelle yaw moments are higher for the upwind rotor but do not indicate significant design problems for either configuration.

Glasgow, J. C.↗
NASA NTRS1981

Instrumentation applications to Space Shuttle models and thermal protection system tiles tested in NASA-AMES wind tunnels

The highlights of the many wind-tunnel tests conducted in the course of the Space Shuttle development program are presented with emphasis on instrumentation applications. The examples of tests discussed include airframe aerodynamics, aerodynamic heating, aerodynamic noise, tile dynamic response, and tile loads. Many of the tests were conducted with standard wind-tunnel instrumentation. Most of the more unusual instrumentation requirements were related to the thermal protection system, where some pressure-sensor concepts were adapted to measure airloads on tiles. These measurements provided the only quantitative data that could be used to confirm the airload analysis procedure. Limited applications of computers to experimental control, in conjunction with data taken during Shuttle tests, have resulted in substantial benefits in overall test efficiency.

Coe, C. F.↗
NASA NTRS1983

A short cut integration scheme to determine the dynamic response of a launch vehicle with several payloads

The coupled base motion equations of a system composed of a launch vehicle and several payloads are derived. In previous work it was shown how the special form of these equations allow for a quick and accurate solution both for the response and the loads of the system. In this paper a short-cut version of this direct integration technique is presented and evaluated. The result is a method which, depending on the nature of the structure at hand, vasilates between a full-scale coupled base motion approach and an open loop base drive method. Although completely general, the presented technique is most effective when the number of interface degrees of freedom is relatively small compared to the overall number of degrees of freedom of the system. The S.T.S.-S.T.-O.M.S. Kit system is used as an illustrative example.

Engels, R. C.↗
NASA NTRS1984

SPIKE-2: a Practical Stirling Engine for Kilowatt Level Solar Power

Recent advances in the art of free piston Stirling engine design make possible the production of 1-10kW free piston Stirling linear alternator engine, hermetically sealed, efficient, durable and simple in construction and operation. Power output is in the form of single or three phase 60 Hz. AC, or DC. The three phase capability is available from single machines without need of external conditioning. Engine voltage control regains set voltage within 5 cycles in response to any load change. The existing SPIKE-2 design has an engine alternator efficiency of 25% at 650 C heater wall temperature and a service life of over three years in solar service. The same system can be scaled over a range of at least 100 watts to 25kW.

Beale, W. T.↗
NASA NTRS1984

A theoretical study of resin flows for thermosetting materials during prepreg processing

A flow model which describes the process of resin consolidation during prepreg lamination was developed. The salient features of model predictions were explored. It is assumed that resin flows in all directions originate from squeezing action between two approaching adjacent fiber/fabric layers. In the horizontal direction, a squeezing flow between two nonporous parallel plates is analyzed, while in the vertical direction a poiseuille type pressure flow through porous media is assumed. Proper force and mass balance was established for the whole system which is composed of these two types of flow. A flow parameter, CF, shows to be a measure of processibility for the curing resin. For a given external load-F the responses of resin flow during prepreg lamination, as measured by CF, are categorized into three regions: (1) the low CF region where resin flows are inhibited by the high chemoviscosity during initial curing stages; (2) the median CF region where resin flows are properly controllable; and (3) the high CF region where resin flows are ceased due to fiber/fabric compression effects. Resin losses in both directions are calculated. Potential uses of this model and quality control of incoming prepreg material are discussed.

Hou, T. H.↗
NASA NTRS1985

Coupled rotor-body vibrations with inplane degrees of freedom

In an effort to understand the vibration mechanisms of helicopters, the following basic studies are considered. A coupled rotor-fuselage vibration analysis including inplane degrees of freedom of both rotor and airframe is performed by matching of rotor and fuselage impedances at the hub. A rigid blade model including hub motion is used to set up the rotor flaplag equations. For the airframe, 9 degrees of freedom and hub offsets are used. The equations are solved by harmonic balance. For a 4-bladed rotor, the coupled responses and hub loads are calculated for various parameters in forward flight. The results show that the addition of inplane degrees of freedom does not significantly affect the vertical vibrations for the cases considered, and that inplane vibrations have similar resonance trends as do flapping vibrations.

Ming-Sheng, H.↗
NASA NTRS1987

Active control of flexural vibrations in beams

The feasibility of using piezoelectric actuators to control the flexural oscillations of large structures in space is investigated. Flexural oscillations are excited by impulsive loads. The vibratory response can degrade the pointing accuracy of cameras and antennae, and can cause high stresses at structural node points. Piezoelectric actuators have the advantage of exerting localized bending moments. In this way, vibration is controlled without exciting rigid body modes. The actuators are used in collocated sensor/driver pairs to form a feedback control system. The sensor produces a voltage that is proportional to the dynamic stress at the sensor location, and the driver produces a force that is proportional to the voltage applied to it. The analog control system amplifies and phase shifts the sensor signal to produce the voltage signal that is applied to the driver. The feedback control is demonstrated to increase the first mode damping in a cantilever beam by up to 100 percent, depending on the amplifier gain. The damping efficiency of the control system when the piezoelectrics are not optimally positioned at points of high stress in the beam is evaluated.

Gerhold, Carl H.↗
NASA NTRS1988

Modeling the viscoplastic behavior of Inconel 718 at 1200 F

A large number of tests, including tensile, creep, fatigue, and creep-fatigue were performed to characterize the mechanical properties of Inconel 718 (a nickel based superalloy) at 1200 F, the operating temperature for turbine blades. In addition, a few attempts were made to model the behavior of Inconel 718 at 1200 F using viscoplastic theories. The Chaboche theory of viscoplasticity can model a wide variety of mechanical behavior, including monotonic, sustained, and cyclic responses of homogeneous, initially-isotropic, strain hardening (or softening) materials. It is shown how the Chaboche theory can be used to model the viscoplastic behavior of Inconel 718 at 1200 F. First, an algorithm was developed to systematically determine the material parameters of the Chaboche theory from uniaxial tensile, creep, and cyclic data. The algorithm is general and can be used in conjunction with similar high temperature materials. A sensitivity study was then performed and an optimal set of Chaboche's parameters were obtained. This study has also indicated the role of each parameter in modeling the response to different loading conditions.

Abdel-Kader, M. S.↗
NASA NTRS1990

Three dimensional full potential method for the aeroelastic modeling of propfans

A three-dimensional time dependent full potential aerodynamic analysis of single rotation propellers has been developed. The primary purpose of the code is to provide a capability of doing propfan aeroelastic analysis in the nonlinear transonic regime. A secondary purpose is to provide a validation of the unsteady lifting surface panel method that has been have developed. Results will be shown for steady state aerodynamic loading, unsteady aerodynamic response to forced aeroelastic deformations, and free aeroelastic response. Comparisons are made to experimental data and corresponding panel code results.

Williams, Marc H.↗
NASA NTRS1991

Control system software, simulation, and robotic applications

All essential existing capabilities needed to create a man-machine interaction dynamics and performance (MMIDAP) capability are reviewed. The multibody system dynamics software program Order N DISCOS will be used for machine and musculo-skeletal dynamics modeling. The program JACK will be used for estimating and animating whole body human response to given loading situations and motion constraints. The basic elements of performance (BEP) task decomposition methodologies associated with the Human Performance Institute database will be used for performance assessment. Techniques for resolving the statically indeterminant muscular load sharing problem will be used for a detailed understanding of potential musculotendon or ligamentous fatigue, pain, discomfort, and trauma. The envisioned capacity is to be used for mechanical system design, human performance assessment, extrapolation of man/machine interaction test data, biomedical engineering, and soft prototyping within a concurrent engineering (CE) system.

Frisch, Harold P.↗
NASA NTRS1990

Analysis of the thermal performance of heat pipe radiators

A comprehensive mathematical model and computational methodology are presented to obtain numerical solutions for the transient behavior of a heat pipe radiator in a space environment. The modeling is focused on a typical radiator panel having a long heat pipe at the center and two extended surfaces attached to opposing sides of the heat pipe shell in the condenser section. In the set of governing equations developed for the model, each region of the heat pipe - shell, liquid, and vapor - is thermally lumped to the extent possible, while the fin is lumped only in the direction normal to its surface. Convection is considered to be the only significant heat transfer mode in the vapor, and the evaporation and condensation velocity at the liquid-vapor interface is calculated from kinetic theory. A finite-difference numerical technique is used to predict the transient behavior of the entire radiator in response to changing loads.

Boo, J. H.↗
NASA NTRS1991

Developments in impact damage modeling for laminated composite structures

Damage tolerance is the most critical technical issue for composite fuselage structures studied in the Advanced Technology Composite Aircraft Structures (ATCAS) program. The objective here is to understand both the impact damage resistance and residual strength of the laminated composite fuselage structure. An understanding of the different damage mechanisms which occur during an impact event will support the selection of materials and structural configurations used in different fuselage quadrants and guide the development of analysis tools for predicting the residual strength of impacted laminates. Prediction of the damage state along with the knowledge of post-impact response to applied loads will allow for engineered stacking sequencies and structural configurations; intelligent decisions on repair requirements will also result.

Dost, Ernest F.↗